Search Documents

Acupan is considered to be an intrusive centre as several igneous phases have been emplaced in the vicinity of the mine over the past 8 Ma. They include the Lucbuban gabbro, Virac granodiorite, Ampucao dacite porphyry (ADP), Hartwell plug, Itogon plug and the multi-phase Balatoc diatreme. These intrusives have high-K calc-alkaline affinities and are grouped together as the Virac Complex.Porphyry-style mineralisation formed during the final crystallization of the ADP in the late Pliocene, with the deposition of two vein stages from high-temperature hypersaline magmatic-hydrothermal fluids. K-silicate alteration halos surround the first stage of veinlets (stage I); they are surrounded in turn by a propylitic assemblage. White sericite and/or intense propylitic halos envelop the second stage of veinlets (stage II) and grade into a weak nrnnvlitir accPmht o

Jan 1, 1990

QEMSCAN« technology is a widely accepted automated e-beam technique providing quantitative and statistically robust mineralogical data to the mining industry. It uses X-ray mapping combined with backscattered electron (BSE) brightness to identify minerals in almost any type of geological material (Gottlieb et al, 2000). Besides the modal mineralogy also the liberation, associations, average grain size and other textural information can be obtained. The aim of this study is to test reproducibility of this technique by setting up and running standard tests on different QEMSCAN« systems. Multiple sample blocks were prepared by our standard operating procedure as epoxy-mounted, carbon-coated, polished blocks. The replicates were measured under the same conditions and measurement parameter settings on different QEMSCAN« instruments. The relative standard deviation (RSD) for the set of measurements was calculated. Generally the reproducibility of the systems themselves was found to be excellent, ranging between 0.4 and 1.5 per cent RSD. The more significant change in the reproducibility was found to be caused potentially by the sample preparation and variation in the mineralogy of the replicates. The measurement parameter settings together with these variations can account for almost 15 per cent RSD for minerals of low abundance. For analysed samples good results for the main phases present in quantities higher than 2 - 5 wt per cent of the total mass of the sample were confirmed with RSD generally below six per cent. Following the experiments, the parameters having the biggest influence on the performance of the QEMSCAN« and its precision are discussed in detail. The importance of sample preparation procedures and measurement parameter settings is emphasised. It is shown that experience and excellence is necessary for getting the most from the automatic mineralogical methods like QEMSCAN«.

Jan 1, 2008

THE absence of any locality maps of the district of Morobe has been seriously felt by mining engineers engaged on the goldfields, and as it was evident at the beginning of operations that the administration would be unable to make good this deficiency, ascheme for making rapid traverses was worked out, and in all subsequent travelling the necessary records were kept for the construction of a reliable reconnaissance map of the Bulolo goldfield and its approaches (see Plate 1.). Since all the field work had tobe carried out without encroaching on primary duties, the compilation of sufficient data was a somewhat lengthy business. It was found that in this r;ough country a pedometer was useless, as it was impossible to calibrate it for the variation in length ofpace between climbing semi-precipices and walking over level country. Further, the native tracks "meander" so excessively that the only method of calculating air-line distance is by timing, and a knowledge of what the timing represents, and until a 10kg experience had been gained in the time taken to cover known distances in various types of-country, one could not feel competent to estimate sufficiently accurately. It was found that reliability could be attained only when walking at nearly top pace. Inregard to aeroplane traverses, results were reliable only when the air was fairly still.BEARINGSIn arriving at the bearing between main traverse points, the method used was to keep a "boy" about two chains- behind when marching and sight back on him, standing, at about two-chain intervals. These bearings were averaged into the field book at the end of the day, each line being averaged separately. As the roads became known, it was possible to get a considerable amount...

Jan 1, 1928

Launching the Queensland Water Plan 2005 - 2010 in August 2005, Premier Peter Beattie compared the stateÆs water resources with liquid gold. QueenslandÆs peak industry body for the minerals and energy sector, the Queensland Resources Council (QRC), believes the analogy is appropriate. During early development of an industry water strategy, it has become apparent that water is like liquid gold, in that it is revered, hoarded, recycled, priced on purity, a magnet for speculators, both difficult and expensive to transport effectively, heavily regulated and fundamentally linked to issues of security. To date it has generally been economic and relatively straightforward for the resources sector to secure water. Although production has not been compromised, this must not be grounds for complacency as there is every indication that water will continue to become increasingly expensive, more tightly regulated and, relative to a growing demand for a finite water supply, increasingly scarce. During 2006, QRC has developed and is implementing a voluntary industry water strategy to address a range of challenges confronting the resource sectorÆs security of access to water. As a consequence of, at times, protracted community consultations over QueenslandÆs catchment-based water planning processes it has become clear that many community stakeholders have outdated perceptions of the stateÆs resources sector. Once established, QRCÆs water strategy will incorporate a community engagement campaign to present the industryÆs credentials as a leader in water resource management. The development of QRCÆs water strategy, and the challenges the strategy is designed to address, provides insight into the fundamental reforms that are occurring in how water is managed and regulated in Queensland. These reforms have implications for how government policies are designed and administered and also for how industry engages with communities during this transition process.

Jan 1, 2006

The current talk of risk management as a separate discipline and management function is like earlier imposition of Quality Control (QC) as an overlay on shoddy production management. Risk management is vital, but is integral in the way we marshal our staff, make decisions, then monitor and review and make crucial secondary decisions. New leaders must not assume that hiring experts ensures good decisions. It is only the essential step one. The worst company I worked for had more expertise than the best. The difference was in culture and decision-making processes. Failed feasibility studies, persistent technical factions in a company that cancel each other, heaps of expert consultant reports piled up like a dump of bricks, even great but half-managers in large and small companies cancelling expertise at their disposal, are the worst manifestations. Just daily foul-ups are common even amongst smart people. We miners have made a great industry but are content to drift far below excellence, even where that word is bandied around. All the management literature and management courses will not right the situation û we have been sending budding managers to this good stuff for two generations and the effects are worthwhile but marginal. A few key ideals, ideas and slogans are not the way. These make inspiring books that work about as long as the Christmas spirit does in the real world. What we need is a coachesÆ manual and a standard of the essential package of culture and work processes that make excellence possible and show how to maintain it long term. It has not been written until now because most managers want to remain dilettante amateur managers without the discipline that creates excellence. First, believe excellence is possible and worth any effort; then commit to it.

Jan 1, 2007

Completion of a project requires two separate money-focused activities, namely economic evaluation of the cash flows underlying the project (before financing) and if the economics look promising, how it can be financed. Economic evaluation might be best led by a person with a technical-operating background, whereas financing might be best led by an accountant. Both should be presented in simple language with easy to understand models. Economic evaluation has a sad and bad history because it evolved from the fringes of accounting. Anyone can become a self-appointed practitioner. Some still take pride in mathematical complexity without realising that they distance themselves from the decision-makers and alienate other team members. Today there is no evaluation modelling consistency across the mining industry and this reflects poorly on our discipline. It is not tolerated amongst our peers in engineering and accounting. In 2009 æbest practiceÆ economic evaluation modelling is well defined. It is:easy to follow;tailored to its purpose;transparent;discipline, rigour and consistency;recording of all source data; and hencequick to audit. Mantra: If you cannot readily understand my model you do not have a problem, I do! The task of the economic model is to make the range of business cases underlying the decision easy to understand. Intellectual power is used to simplify the decision to its key issues and risks and to present the full range of possible business outcomes in readily understood terms. Project team members, management and the board must be able to make their decisions with æeyes wide openÆ. A steering committee should be established to develop a set of standards and practices that could be adopted for economic modelling within the industry. The industry needs to purge itself of the undisciplined economic evaluation modelling that now characterises the discipline.

Jan 1, 2009

In the past few years the Rietveld method emerged as a routine tool for quantitative phase analysis (QPA) from X-ray diffraction data. Fast and reliable results became possible by combining modern computer technology and optimised mathematical algorithms with the fundamental parameters approach in the Bruker AXS TOPAS software. Here the routine analysis of bauxite raw material and of aluminium bath electrolyte is presented. The accuracy of bauxite quantification was tested by analysing the IUCr round robin sample. An agreement of better than one per cent was obtained for minor constituents and a maximum deviation of 2.5 per cent for the major phases. This is excellent agreement with expected results from weighting. Ten different phases were quantified in natural samples from Turkey with a precision better 0.5 per cent for the major phases and one per cent for the minor phases. Additionally, crystallite sizes were obtained from the peak profiles that give valuable information for the processability of the material. XRD data from solidified aluminium electrolytes were rapidly measured using silicon strip detector technology. With the LynxEyeTM detector full patterns were collected in 90 seconds and analysed with TOPAS. It is shown how to derive well-established measures such as bath ratio and excess AlF3 from the Rietveld results. These measures are widely used in aluminium production and readily available with very high precision. The excellent agreement with ALCAN reference data demonstrates the outstanding accuracy of the method. The mean deviation between here presented results and reference data is below 0.5 per cent for total CaF2, below 0.25 per cent for excess AlF3 and 0.02 for the bath ratio. The precision of the method was evaluated by repeated measurements.

Jan 1, 2008

By I Warren, M P. Simpson

Adularia-sericite epithermal ore deposits have well-documented alteration mineral zonation patterns with distinctive geochemical signatures. Proper use of whole-rock geochemistry can provide useful vectors for exploration and can enhance efforts to characterise and quantify the mineralogy and intensity of hydrothermal alteration.   Analyses of Au and Ag provide the most direct vectors to orebodies, and pathfinder elements such as As, Sb, Hg, Zn, Pb and Se are similarly zoned around at least some orebodies. However, the minerals that contain these elements occur almost exclusively in veins, and therefore identifying geochemical vectors related to wallrock alteration that is zoned outward from orebodies is crucial for effective exploration.   Distal alteration zones contain quartz-illite-chlorite-carbonate-pyrite, whereas samples proximal to veins contain quartz-adularia-pyrite, with lesser though variable illite-chlorite-carbonate. Therefore, adularia-sericite epithermal ore deposits show K alteration in their cores. The resulting K-metasomatism can be evaluated in several ways. Areas that have been most intensely altered are commonly characterised by highest K contents, but these results can be complicated by variations in rock type across the prospective area. Potassium mass balance results provide a robust and rigorous assessment of K-metasomatism, however, knowledge about the composition of fresh rocks and correct identification of fresh precursor compositions of altered rocks are required. Three alteration indices provide effective evaluation of K-metasomatism: 1.   the K number, which is the ratio K/(2Ca+K+Na) (molar); 2.   Barrie values [(K2O * 100) / Sr]; and 3.   the Rb/Sr ratio. In most places these provide similar vectors, although K numbers can be complicated by the appearance of hydrothermal calcite and/or albite.   Plots of K/Al vs (2 Ca + K + Na)/Al (molar) allow estimation of the intensity of K-metasomatism and its mineralogical products, thereby complementing traditional XRD and petrographic studies of alteration minerals.

Jan 1, 2005

Although the effects of sea level changes on ore concentration processes are to some extent obvious with certain deposits, e.g. beach placer deposits, they have been largely overlooked with others such as Mississippi Valley type lead-zinc deposits. It is contended that sea level variations may have more profound effects on a wide range of deposits than has previously been appreciated. These deposits include not only placer'and residual deposits but also stratiform copper deposits, Mississippi Valley type deposits, stratiform manganese deposits and Minette type iron deposits. Sea levels in paralic basins profoundly affect the influx of 'detrital sediment, and this has to be suppressed to allow for the accumulation of thick rich deposits of coal evaporites, phosphate or metalliferous sediment. Emergence can be associated with oxidized waters, erosion, and,solution of soluble rocks. Submergence can reverse the Eh trend and can lead to preservation of ores. Both realms of surficial sedimentary environments and subsurface diagenetic environments can be affected by changes in water pressure, gas pressure (pC02), Eh, pH, and temperature as sea levels fluctuate. Even relatively small sea level changes may have profound effects. For example, there is some evidence to suggest that when the level dropped below 100 metres about 10,000 years ago, the Red Sea became isolated by the sill at Bab el Mandeb in the south, and evaporated away to leave a series of shallow lakes. The Red Sea is 1 to 2 km deep. It was at times such as this that the well-known copper-zinc mineralization developed in the Red Sea trough. Changes in sea level also affect the stability field of gas hydrates which can yield large volumes of gas leading to mass movements on the sea floor (Warnke, 1986).

Jan 1, 1987

By M Donatelli, E Grazio, A Heissenberger

The distribution of a contaminant in a bulk mass greatly influences the effectiveness of sampling procedures. Most currently used sampling guidelines for genetically modified organisms (GMO) testing have stringent distribution requirements. Specifically, all these protocols are based upon the assumption that GM material, if present, is randomly distributed. Yet, assuming randomness is risky because the applied sampling plan may not provide an accurate estimate of the content of the contaminant. Despite the general consensus that an evaluation of the possibility of non-random distribution of GM materials within lots is a pre-requisite for the definition of effective sampling protocols, no experimental data on the distribution of GMOs in kernel lots are available anywhere in the world. Additionally, to date there is no distribution-free statistical model to estimate sampling errors, thus making the theoretical definition of optimal sampling technique impossible when randomness cannot be assumed. Here we present preliminary results of the KeLDA project, which is the first study investigating the distribution of GM materials in large soybean lots imported within the European Union. The extensive variability of GM content, observable both within and among soybean lots, indicates that heterogeneity issues cannot be overlooked when defining sampling strategies for large lots of particulate material and that randomness cannot be assumed a priori. A new statistical model free from any distribution assumptions, developed in order to estimate the sampling error associated with different sampling protocols together with the risk of false-negative results, is also presented. The new model, which is applicable to any consignment of particulate material with respect to any kind of contamination, presents two novelties: first, freedom from any distribution assumption; second, the possibility of estimating the magnitude of the sampling error associated with different sampling protocols as a function of specific distributional properties.

Jan 1, 2005

THE slag from the blast furnaces having been granulated, a representative sample is taken to the sample mill. It is then dried, crushed through a 100-mesh screen, intimately mixed, and packeted for assay purposes.METHOD OF ANALYSISINSOLUBLEWeigh 1 grm. of the finely-pulverized slag into a 3t-in. casserole, moisten with a little water to prevent sticking, cover with a clock glass, and add 20 cc. of hot acid (1 HNOs, 3 HCI, 4 H2 0). Evaporate slowly to dryness on a hot plate and bake (without overheating) until all the gelatinous silica is dehydrated. Cool, add 20 cc. HCI (1-1), and boil gently for several minutes; filter into a 300-cc. beaker, cleaning out the casserole thoroughly with a rubber-tipped glass rod. Wash residue with hot distilled water and transfer it to a No. 1 porcelain crucible. Dry, ignite, cool in a desiccator and weigh as total insoluble matter. Dilute filtrate to 200 cc. and neutralize some of the excess HCI with NHa.OH. Warm, and pass H2S for 15 min. Filter and wash withhot water. Boil off H2 S, oxidize with 5 cc. HNOll , reduce bulk of the solution by evaporation. to about 100 cc., and transfer to a 250 cc. flask.SILICAFuse insoluble residue over a blast lamp in a platinum crucible with three or four times its weight of anhydrous carbonate of soda, for 10 to 15 minutes, or until decomposition is complete. Cool, and extract fusion in an 8-in. evaporating dish with HCI (1-1); rinse crucible and cover with distilled water, and evaporate to dryness over a water bath. Take up dry mass with 10 cc. strong HCI, and then.

Jan 1, 1922

Mineral policy is now generally regarded as a function reserved to government. Government is reponsible for the economic health and progress of nations, and must therefore interest itself in minerals as a basic national resource. Government should therefore identify objectives which it sees as suitable and necessary for the mineral industry so that the industry can play its part in achieving national goals. It should provide the legislative framework and policy guidelines to enable these objectives to be achieved. The essential objective of a national mineral policy should be rational development of the nation's minerals resources. To achieve this, it need not be too formal; broad guidelines are enough. But it must be dynamic, to keep pace with the changing circumstances of the mineral industry in the world scene and the changing requirements of government. It should be flexible, recognising that there is no such thing as a "typical" mineral deposit; above all it should represent the outcome of a continuing dialogue between government and industry. Both government policy and corporate planning need to be formulated on the practical understanding of the potential economic value of the mineral sector and what it can contribute to the nation's prosperity. There needs to be a common understanding of the wide range of the costs of risks that may arise through the exploration and development stages and of the uncertainties affecting ventures at the production stage. There needs to be a common understanding that the size and importance of the mineral sector is determined in the long run by the level of investment in exploration. The development of a continuing understanding between government and industry should lead to the formulation of ground rules which ensure the continuance of a strong industry able to adapt to the changing world scene and make its contribution to national growth and wellbeing.

Jan 1, 1986

The process of mine planning at AnacondaÆs nickel and cobalt laterite operation located at Murrin-Murrin in the Northern Goldfields of Western Australia is carried out in a number of stages in an endeavour to determine the optimum mining sequence in order to maintain supply to the 4 Mtpa plant subject to operational constraints. The 296 Mt @ 0.99 per cent Ni and 0.064 per cent Co ore reserve (based on a cut-off grade of 0.8 per cent Nickel) is spread geographically widely over three regions comprising Murrin North (15 km + 15 km), Murrin South (7 km + 16 km) and Murrin East (5 km + 13 km) (refer Figure 2). The nickel mineralisation has been broken up further within each region into 18 separate manageable block models representing the 32 different deposits. The models are based initially on the 50 m + 50 m resource drilling for long term planning and updated with 12.5 m + 12.5 m grade control drilling prior to mining. Each of the individual block models are optimised using Whittle 4X software to provide the shells used as the basis for each of the 126 pit designs. The pits are generally nested with starter pits targeting the higher value shells with subsequent pits incrementally cutting back ultimately to the life of mine shells. A series of steps including: the coding of the individual pits into the block model; data export; TCL scripting (to calculate additional economic and tracking information); importing; and re-blocking; completes the transfer of the data into a MineMax (mixed integer linear programming schedule optimising software) model. Using MineMax and the application of operational and production constraints allows the optimisation, assessment and economic evaluation of alternative scenarios in order to determine the optimum life of mine plan and schedule.

Jan 1, 2003

The face of project evaluation is changing continuously, making it ever more critical to get a clear understanding upfront of the objectives, decision-making processes and criteria of the project proponents. Requirements are usually significantly different for emerging æjuniorsÆ compared with long established major mining houses and companies in developing countries compared with western companies. Requirements are also different for different types of evaluations, such as due diligence studies compared with feasibility studies of æownedÆ projects and there are often key misunderstandings around the use of the term æbankableÆ. Further, it has become increasingly important with increasingly remote and lower quality resources to understand risk relativities such as infrastructure compared with the core processing facilities. This has also driven the need for more trade-off studies to determine the best balance between critical issues, such as optimisation of the interface between mine and processing plant, capital versus operating cost and automation versus labour. In every project evaluation, it is also critical to consider emerging trends and changing requirements and standards such as sustainability and community interface. Finally, the inescapable drive to reduce time to market has driven changes such as increased use of more standardised designs and innovative approaches to the transition from project development to execution. This paper begins with a brief review of the different objectives and risks of each project development stage to establish a framework for subsequent discussion of the different requirements of different types of companies in different locations, different types of evaluations and different types of projects and project components. This is followed by a review of changing requirements and standards and some innovative developments in sustainability and community interface are presented. Finally, the paper outlines a number of developments in the area of operational readiness planning that focus on minimising the time to achieve maximum return on investment.

Jan 1, 2009

By J D. van Wees

Preliminary project evaluation is relevant to the evaluation process of the decision makers (or executives) prior to making the critical business choices. Important to the assessment is an integrated sensitivity, scenario and risk analysis at every stage of a mining project. This should include the evaluation of different options taking into account uncertainties. Construction of interactive financial computer models where each element is functionally integrated into a fully integrated life-cycle allows rapid and automatic study of the sensitivity of each element through changes in the value of an input. The scenario analysis is the effect of changing more than one input at a time, organised through scenarios in a decision tree. Risk analysis is an integrated analysis of the effect of all uncertainties of the parameters, using Monte Carlo simulation. Key to the asset decisions process is that the decision maker is provided with the essential integrated decision information. We have clustered this information into several scenario groups. Within each group, two levels of uncertain information are distinguished: discrete scenarios critical for the decisions; and remaining uncertainty within the scenario (risk analysis) which can be modelled by continuous probability density functions (pdfÆs). For an asset, the relevant scenarios in each group and the associated continuous pdfÆs need to be defined. When the scenario groups and associated pdfÆs have been defined for the asset, the decision process can be started by structuring the different scenario groups in a Scenario Tree. A Scenario Tree contains decision and end nodes. Each end node corresponds to a completely defined mine project or asset model. The calculations for each end node result in a set of stochastic realisations for the reserves, production forecast, cash flow, and profitability indicators (NPV, IRR, DPR). Thus, a deterministic and fully probabilistic multi-commodity analysis tool is provided to investigate the sensitivity and robustness of decisions.

Jan 1, 2003

Airblast overpressure legislative limits can be extremely difficult to meet throughout Australia, which has by far the most stringent limits of any nation in the world. As the difficulty in meeting the limits is strongly dependent on the scale of mining, it is not surprising that the Australian coal mining industry is experiencing particular difficulties in meeting these limits. Eight full scale overburden blasts have been modelled with respect to overpressure impact for a strip coal mine, involving both dragline (cast) blasting and pre-strip (non-cast) blasting. Overpressure levels in the range 100 to 125 dBL have been measured at distances varying from 2.4 to 5.7 km, and modelling has successfully estimated both the amplitude and shape of overpressure waveforms to within an average of 1.2 dBL. Typical errors of prediction are around 0.6 dBL. This accuracy of prediction has been achieved by considering the impact of only the face holes, and the accuracy of prediction of both shape and amplitude suggests that it is these holes which dominate the environmental overpressure impact at distances in the range two to six kilometres, for cast and pre-strip blasting operations. Modelling has been based upon the Elemental Overpressure Wavelet proposed by Richards and Moore (2002), incorporating actual hole coordinates, actual delay timing, and assumed delay scatter statistics. The incorporation of delay scatter statistics has been particularly significant, and allows the determination of the range over which the peak overpressure levels are expected to vary. To date, modelling has considered only the use of conventional pyrotechnic delays, though simple adjustment to the scatter definition would allow estimation of overpressure levels, and their variability, with electronic delays.

Jan 1, 2004

The object of this paper is not to describe any particular type of engine in close technical detail but rather to give a general picture of past and present practice in this important section of the industry. The subject involves the study of almost 600 years of coal mining history which has fluctuated from stagnation to extremely rapid progress.Up to the year 1300, coal was obtained from outcrops and exposed beds, but this easily worked source soon gave out, so by that time shafts had to be sunk to the coal seams, and coal mining proper commenced its career.These early shafts were very shallow, and winding equipment was not a matter for much concern. Raising coal was generally achieved by human labour, which was called "coal bearing." Coal was loaded into baskets. strapped to a man's back, and carried from the underground workings to the pit bottom. The unfortunate individual then climbed ladders to the top of the shaft, unloaded the basket, and descended the shaft for the next load. Men, women and even children, were employed as the mine expanded, and were generally bound to the colliery for life, performing daily work which would now be regarded as slavery. This primitive method of raising coal to the surface was slow, inefficient and highly dangerous, yet for want of a better method it continued until in 1602 it isrecorded as having been abolished in Wales, one of England's great coal districts. It was not until 100 years later, however, that it was abolished in the northern coalfields, and the colliers were freed forever from their dreadful life.WINDLASSThe first step towards winding coal was the introduction of the windlass. This was similar to the common windlass used over a well, and was operated by man power. The...

Jan 1, 1945

DURING a period extending over about the last two and a half years, the performances of various types of rock drills in use at the mining department of the Zinc Corporation have been recorded as closely as possible. The main objective was the collection of sufficient data regarding internal water-feed hammer drills, when used for the same class of work as the older type reciprocating drill, to enable a decision to be formed on the following points:(1) Whether internal water-feed, hammer drills could efficiently perform the work previously carried out by reciprocating drills without excessive repair cost to the former.(2) If so, was it good policy commercially to eliminate the reciprocating type completely, writing these off together with the accompanying spares, accessories, and solid drill steel, and replacing with internal water-feed hammer drills, with lighter fittings, and the requisite amount of hollow drill steel.(3) What were the best types and makes of hammer drill for different classes of mining work(4) What was the economic aspect of the introduction of the principle of internal water feed to every type of machine throughout the mine.Prior to the strike of workers in May, 1919, Ingersoll-Rand E47 31-in. reciprocating drills had been used for stoping and for the major portion of driving, cross-cutting, and similar work. The accompanying columns and fittings were all 4t in. The drill steel used was solid octagon. Up to 1916 these machines were also used for winzing, after which time jackhamers were more successfully employed. These latter were of the usual types, varying in weight from 40 to' 46 Ib. Ingersoll BCR 430, Holman No. 2 spool valve, Sullivan DP33,. Waugh Clipper 55. These machines were all dry head; the drill steel was hollow hexagon, shanked.

Jan 1, 1923

By R Huntley, D Sims

Pajingo gold mine produces over 240 000 oz Au per year from underground mining using longitudinal bench stoping methods with a 15 m sublevel interval. Average mine head grade is around 12 g/t Au, contained within quartz veins between 0.5 to 16 m wide. The veins dip steeply (>60¦) and exhibit strike variations which lead to many curved and meandering drive/stope geometries. Unplanned dilution at Pajingo is predominantly controlled by fault planes that subparallel the vein and commonly lead to slabbing failure from the stope walls. Initial efforts at determining maximum spans were based on using the Stability Graph method of stope stability. However the method had a number of shortcomings that did not address mine site observations, including previous mining, interaction of different joint sets and the presence of discrete shears which resulted in poor prediction of stability. A method was developed to rate the risk of dilution for a stope based on observations made in the ore drives. The method utilises profile mapping of the ore drive, structural features observed and the orebody itself, on 10 m spaced sections along the ore drive. A matrix of factors determines the dilution risk for stoping at the time of mapping and the rating is transferred to longsection plots in the office. The dilution risk rating is used to determine the position and density of cable bolt support aimed at lessening the risk, and can be used to review blasthole designs prior to finalisation. The method has been used for more than two years and has proven to be a good indicator of potential unplanned dilution (ie waste outside of ring design). A recent review of the dilution risk mapping process has indicated it is assisting in reducing the impact of dilution at the operation and has the scope to be utilised further in the design process.

Jan 1, 2002

By K Zic, P Pickering, P Fraser

Water is a defining feature of the Pilbara. Its management was and remains vital for the pastoral industry which European settlers established when they first came to the Pilbara, and for the mining industry which now dominates economic activity in the Pilbara. Water availability in the Pilbara is, however, problematic. Severe droughts and major floods can occur at close intervals. In response to this uncertainty, the Department of Water undertook a Prefeasibility Study to determine, at a high level, the water requirements and opportunities in the Pilbara region. This paper reports on the outcomes of this study and the water integration opportunities in the region, identifying the sources of water supply and offers possible options for managing this water sustainably for the present and future demand. A range of supply opportunities is reviewed including: dewatering from mining operations, surface water, and desalination. All opportunities were subject to order of magnitude costing, including capital, whole of life and retail unit pricing with preferred options receiving further interrogation through triple bottom line (TBL) analysis to prioritise solutions. Options were also subject to intangible quantification (IQ) including benefits from the reduction of carbon emissions to ensure that the preferred option is based on factors other than just the least cost. Demand analysis was undertaken to identify current and future requirements and were assessed through review and integration of regional and sub regional master plans and consultation with mining, agriculture, industry and the community. The paper concludes that the viability of a Pilbara integrated water supply scheme depends on the development of a financial mechanism involving both government and industry participation models. The agreed scheme formed the basis of a submission to Infrastructure Australia for funding assistance.

Jan 1, 2009