Search Documents

Conflicting claims and views on the priming of ammonium nitrate/fuel oil (ANFO) are reviewed; certain fallacies and misconceptions are rectified. Optimum priming systems for a range of blasthole conditions are indicated. Moves towards optimum priming lead to reductions in the combined cost of drilling, blasting and handling the material. With shallow blastholes, two-point priming is rarely warranted. Best blasting results from single priming are usually obtained when the primer is located near, but not at, the bottom of the blasthole. As blast- hole depth increases, two-point priming becomes more reliable and effective than single priming. For two-point priming, primers should be located such that detonation waves in the ANFO collide at grade level or, if preferred, within a hard band in the burden. Where blastholes are very deep and/or strata variations can be appreciable, three or more spaced primers are often justified. The effectiveness of a primer varies with its detonation pressure, diameter and length. Primer properties influence the velocity of detonation (VOD) near the primer, but do not affect the final (steady-state) VOD in the ANFO. Some primers cause 'run-up' (i.e. lower than steady-state) velocities whereas others cause

Jan 1, 1974

The Mt Leyshon Gold Mine is located 30 kilometres south of Charters Towers in Northern Queensland. The current open cut mine has been in operation since 1986. In 1992 a feasibility study was completed that recommended an increase in production to over 240 000 ounces of gold per year. This proposal required an upgrade of the processing plant to five million tonnes per year, and an enlarged mining fleet to provide additional ore, and to meet the increased waste removal requirements. The implementation of the mine expansion program during 1993 required the Life of Mine plan to be extensively revised. This required the assessment and management of potential risks associated with the mine design. The updated geological model using the 1992 drilling results along with the actual contract mining and processing costs were used to establish a series of nested optimised pit shells. The total and incremental quantities and costs were then analysed to determine a suitable pit perimeter. The pit and phase plans were then created and used to devise a staged development plan. The block layout plans for each bench were then established from which a detailed life of mine production schedule was created.

Jan 1, 1994

By E V. Man, O N. Savassi, J-P Franzidis

In flotation, the property that is exploited to effect the separation of a mineral from an ore is referred to as its floatability. Assessment and quantification of ore floatability is of fundamental importance in modelling and simulation of flotation circuits. This paper describes the design, construction and operation of a new laboratory flotation rig that has been developed at the Julius Kruttschnitt Mineral Research Centre (JKMRC) to determine the floatability of different ores on a small-sale. The rig is designed for continuous operation. The major features of the rig are highlighted in this paper. An unique characteristic of the rig is a 9.1 L conditioning vessel. This provides a mixing regime close to plug-flow which avoids complications such as different collector coverages for similarly sized particles (which would considerably increase the complexity of ore floatability determination). The main advantages of this rig when compared to conventional batch flotation cells include better control of the chemical environment and the ability to determine froth recovery, entrainment and water recovery with increased accuracy. Preliminary tests undertaken with a high-grade lead/zinc ore from BHP Cannington are presented demonstrating the good level of reproducibility obtainable in operating the equipment.

Jan 1, 2000

The comminution process indicates that the most energy-efficient comminution system would be one where the particles leave the breakage field as soon as they reach product size. Contrary to the free falling gravitational (vertical) flow in crushers, the grinding millÆs energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of a pulp lifter is to transport the broken material and slurry from the discharge grate out of the mill. Hence, the design optimisation of pulp lifters affects not only the energy efficiency and throughput of autogenous grinding/semi-autogenous (AG/SAG) grinding mills, but also contributes other process benefits such as improved wear life and operator-friendly steady and smooth mill operation. Following its introduction in 2006, OutotecÆs patented Turbo Pulp Lifter (TPLÖ) design has been retrofitted at existing sites and also installed in some new ones around the world. This paper will provide operational experience and data on how the TPLÖ design has allowed AG and SAG mills to operate efficiently.

Jan 1, 2009

Expansion of the B.H.P. Co. Ltd. mater ials handling facilities, at their Newcastle Steelworks, began in 1964 and continued until 1970. The present complex handles the annual iron ore requirement of some three million tons for the Sinter Plant and Blast Furnaces. Iron ore is discharged from ore carriers and conveyed at rates up to 3,000 t.p.h. to either of two 180,000 ton capacity storage yards, where it is blended using boom stackers. Material is reclaimed from these yards at rates up to 1,000 t.p.h. using a slewing boom bucket-wheel reclaimer and fed to a screening station. Oversize material is scalped out and crushed in a closed circuit cone crusher. Undersize material is sized on double-deck vibratory screens which separate at 1/4in (6mm). The two fractions are blended in two of four 70,000 ton capacity blending yards using slewing boom travelling stackers. Bridge-mounted bucket-wheel reclaimers reclaim the blended piles at 1,000 t.p.h. Fine ore is conveyed to the Sinter Plant and lump ore to a second screening station, for rescreening, before passing to the Blast Furnace.

Jan 1, 1972

By Bhattacharyya A. K>

The Pemali Open Pit Mine is situated in a small island called Bangka in Indonesia. It produces approximately 165,000 m3/year of tin ore with an average grade of 3.67 kg/m' of tin from a primary deposit. The deposit occurs at the rim of a granitoid intrusion within sedimentary beds. The rock formations, all extremely weathered, and the overlying alluvium, are exposed to a rainfall exceeding 3m/year. Serious slope stability problems are experienced at the mine, despite using overall pit slopes of 20¦-29¦, the latter resulting in a stripping ratio of 4:1. This paper outlines a computer based back analysis of a major slope failure involving some 250,000 m' of material which occurred on the west wall of the pit in February, 1984. The findings from the analysis, together with other information, are used to examine the stability of the east wall of the pit, where tension cracks developed later. The results indicate that the large influx of water was the most significant cause of such slope stability problems and a more intensified water management programme would be beneficial.

Jan 1, 1989

By Wilson CJN

The central Taupo Volcanic Zone is a region of intense Quaternary silicic volcanism accompanying rapid crustal extension. Modem central TVZ is the most frequently active and productive silicic volcanic system on Earth, erupting rhyolite at c. 0.28 m' s'. The rhyolites show no major compositional changes with time, but the total extent of magma chamber zonation has changed with the advent of rifting and crustal extension at c.0.7 Ma. At least 34 caldera-forming ignimbrite eruptions have formed a complex sequence of relatively short-lived, nested and/or overlapping volcanic centres in central TVZ. Taupo contrasts with other large silicic magmatic systems in the exceptionally high frequency, but small size, of caldera- forming eruptions. This contrast reflects the thin, rifted nature of the TVZ crust, that precludes the development of long- term magmatic cycles at Taupo.Within central TVZ, non-rhyolitic compositions have been erupted apparently irregularly in time and space; in particular there is no evidence for a geographic separation of basalts from andesites. TVZ is a rifted arc, but its segmented nature, high thermal flux and voluminous rhyolitic volcanism make it unique on Earth.

Jan 1, 1995

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. J. G. SYMONS) IN PRESENTING THE CERTIFICATE TO ROBERT COLVILLE BRADSHAW, O.B.E.Today it is my privilege and pleasure to introduce to you, Robert Colville Bradshaw. O.B.E., the third New Zealander to be honoured with Honorary Membership of The Institute. Sir William Hudson and Mr. C. H. Benney were the others.Mr. Bradshaw has been an Affiliate Member of The Institute since the formation of the New Zealand Branch in 1966. Like his friend Matt Benney. Bob Bradshaw is an accountant by training. Last June he retired as senior partner of the firm of chartered accountants, now known as Wilkinson Wilberfoss, with which he served from January 1929.Mr. Bradshaw grew up in New Zealand attending the Terrace School in Wellington, the New Plymouth Boys' High School where he was a boarder, and completing a Bachelor of Commerce at the university now known as the Victoria University of Wellington. He is an elected Fellow of the New Zealand Society of Accountants and an Associate of the United Kingdom Institute of Cost and Works Accountants.

Jan 1, 1977

By Eren H

For a hydrocyclone of fIXed geometry, DC, Di, DO and ? are constants, the variable parameters affecting the performance are Qi, Fi, Du and H. (See Appendix 2 for definition of symbols).The relationship between d50c, Qi, Fi, Du and H gives models which can effectively be used for performance predictions. Such models have already been established by Lynch et al and by Plitt.These models have been tried in a limited manner under continuous operating conditions for on-line cowol. For on-line control effective and accurate instrumentation is required for which a new set up is proposed. Using this set up, a new model was established. A feature in this model is that deviations from the norm of operational parameters affecting d50c were considered. It is shown that these deviations generated by the disturbance of one or more of variations in the parameters, can be monitored by a computer and suitable signals generated to control servo mechanisms for restoring the required d50c value.The logic followed in developing the computer software is described and the application of the model is indicated.

Jan 1, 1990

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

By R Frew, E Wong, G Ferguson

The Chang Jiang Tunnel and Bridge Project, when completed, will provide a fixed link between ShanghaiÆs rapidly developing Pudong District and Chong Ming Island, situated in the Yangtze River delta. The link includes 7.5 km of bored tunnel from the Pudong to the intermediate Changxing Island from where the link comprises viaduct and a cable stayed bridge. The bored section comprises twin 13.7 m internal diameter segmentally lined three-lane highway tunnels. At its deepest point the tunnel will be 55 m below the river. Cross passages will link the two bores for passenger evacuation. Tunnel boring commenced in October 2006 and is scheduled for completion in mid-2009. The paper describes the key features of the design and construction of the bored tunnel by two 14.53 m diameter slurry TBMs and eight cross passages using ground freezing techniques in alluvial sediments. A decision to include light rail below the road deck was taken after the completion of the detailed design. This posed a number of design challenges including passenger evacuation to the road deck, and the redesign of the low point sumps. The various options considered are discussed together with those adopted for construction.

Jan 1, 2008

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important alvantage. of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate: (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elim-ination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the thresthold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step copper smelting is still a process of the future.The paper describes the potential advan-tages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985

By Zervoudis J

Limitations of current touch-up solders for galvanised steel include coating thickness control problems and poor corrosion and abrasion resistance as well as health and environmental concerns due to toxic constituents such as lead. This paper reports on progress in ILZRO-sponsored research to develop an improved touch-up solder. Encouraging results were achieved in torch soldering trials with experimental zinc-tin-based alloys. Mouldability and coating thickness control were achieved over a practical working temperature range in which the solders consisted of a viscous mixture of solid primary zinc phase particles in a liquid zinc-tin eutectic matrix. The mouldability was dependent on the microstructure of the solder sticks, and optimum structures could be obtained through control of casting solidification rates and by the addition of small amounts of copper. Hardness, abrasion resistance, adhesion and corrosion tests on experimental Zn- (40 - 50 per cent) Sn-I per cent Cu also showed improved performance over lead-tin-zinc solders and compared the effects of tin content within this range. Atmospheric corrosion testing and optimisation of alloy composition and methods of solder stick production are continuing.

Jan 1, 1993

By X X. Qiu, T Zhang, B L. Wang, X Qiu, Y H. Du

This paper summarises the information about current state of eco-environmental problems, geological disaster and mining waste causing during the process of limestone mining. By comparing the management experiences of limestone mines in other countries, management problems in China have been discussed and improved management options have been proposed here. These options include: accelerating the process of legislation, promoting and strengthening environmental impact assessment for limestone mine, and increasing compensation requirements according to the local eco-environment conditions.CITATION :Wang, B L, Qiu, X X, Qiu, X, Zhang, T and Du, Y H, 2012. Eco-environmental problems caused by the process of limestone mining and management options, in Proceedings Life-of-Mine 2012 , pp 357-360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By K Hooper

Over the past 20 to 30 years statistics as a science has grown in significance. Not a day passes without reference to the latest statistics by the print, audio and audio-visual media. The Northern Territory Government has been part of this growth and like other public and private sector organisations collects a broad range of statistics. The Northern Territory Department of Mines and Energy participates in the government's statistics collection process. Statistics collected and published by the Department of Mines and Energy include geoscientific; mining and exploration tenure; environmental (e.g. mine site waste water management); production of minerals, oil and gas; mining sector employment; and occupational health and safety. The importance of statistics collection to the Northern Territory Government is discussed in the paper.

Jan 1, 1994

By G Johnson, G W. Wilson

The settlement and drainage behaviour of co-mix, or mixtures of waste rock and tailings, are examined in a column study. Three co-mix profiles were observed for settlement, drainage, and pore water pressure response. A fourth profile with waste rock and no tailings was also observed for settlement. Co-mix consolidated faster than predictions for tailings alone, and maintained a saturated void space relative to waste rock alone. Practical benefits of co-mix as a waste disposal technology may include faster time to consolidation than tailings, a reduction in total settlement of placed material compared to tailings alone, and a reduction in acid drainage by limiting the flow of water and oxygen through maintenance of a saturated void space.

Jan 1, 2003

By Andersen AK

A previous paper (1) indicated that electrowinning of copper at current densities considerably higher than those currently employed in electrowinning operations is technically feasible. It is of interest, therefore, to establish the extent of economic benefits which may be obtained from high current density operation and to determine the value of the optimum current density. Optimization of electrorefining processes has been discussed in considerable detail by Ibl (2) and Schmidt (3) whop from theoretical considerations, derived expressions for the optimum current density. In this work, general equations relating both the capital investment and the production cost for copper electrowinning plants to current density and plant capacity are established. From these equations, the optimum current density can be calculated for any desired plant capacity.

Jan 1, 1969

Does coal mining get enough out of its people?. In a number of cases, Yes. Several companies have rethought their management systems and accordingly are improving their utilisation of people to improve productivity. For some, capital and technology are the panacea for improved productivity and lower costs. Computerised mine planning, improved beneficiation processes, heftier longwall equipment, bigger trucks and shovels and upgraded coal clearance systems are expected to provide the answers.Whilst these factors are important they only contribute to part of the productive potential of a mining operation. Production flexibility provided by recent Industry award changes has brought about increases in total output. However, these improvements have not been matched by corresponding decreases in the unit cost of production.

Jan 1, 1991

Traditionally mill operators have been employed with varying educational backgrounds with little if any formal training in aspects of mineral processing. Pasminco Mining-Rosebery, in line with other organisations, saw the need for a prerequisite entry level for operators to enter the industry. After initial discussions between various West Coast Mines personnel, union and government representatives, an industry working group was formed in 1989 with the aim of developing a traineeship suitable for the mineral processing industry. Training and technical representatives from four of the West Coast Mines and TAFE were commissioned with the curriculum development. The resultant course, which is recognised under the Australian Traineeship system, involved an integrated on and off-the-job training program, including 13 weeks of formal off-the-job instruction.

Jan 1, 1991

To reduce the corrosion of a stainless steel crystallizer, caused by accumulation of chloride impurity in the liquor during the crystallization of ammonium sulphate, a strongly basic anion exchange resin in the sulphate form may be used to remove the chloride from the liquor. The spent resin may be regenerated with dilute ammonium sulphate.The ions involved are sorbed by the resin in the order Equation 1. The sorption of chloride from the liquor and the regeneration of the resin depend upon the effect of concentration on the formation of the the ion pair NH6SO4. The sulphate ion dominates sorption from dilute solution of ammonium sulphate containing minor amounts of choride; choride ion dominates sorption from concentrated solution.

Jan 1, 1976