Search Documents

The transportable moisture limit of a mineral concentrate (TML) is of great importance in the shipping of that material from Australian ports. Each year Australian mining companies incur substantial costs as a consequence of delaying shipments and/or multi-handling concentrates so as to comply with transportable moisture limits. Despite this there is a general lack of in-depth knowledge concerning factors that influence the parameter. Eight major Australian mining companies supplied sizing, specific gravity and TML data for their concentrates. Zinc, lead, copper and bulk concentrates were represented in their data. Estimated surface areas of the concentrates, as calculated from their normalised sizing data, correlated strongly with the reported transportable moisture limits. This high correlation prevailed in spite of the acknowledged limitations associated with the use of multi-sourced data and the adoption of simplistic approaches in the normalisation of sizing data and the estimation of surface area. Based on the broad range of concentrates studied, concentrate sizing data were concluded to offer potential as an alternative means of reliably estimating transportable moisture limits.

Jan 1, 1993

By Gardavsky V, Gabell AR, Green AA

The I,)hyllosilicate mineral chlorite is a common constituent of altered rocks associated with volcanogenic massive sulphide deposits, and literature studies indicate that, in general, this mineral is progressively enriched in magnesium relative to iron as an orebody is approached. Studies have shown that there is a direct correlation between the Mg/Mg + Fe ratio of chlorite and its absorption spectra in the 2.7 to 3.0 um range. However, this region, which contains the fundamental 0-H stretch absorption features, is affected by intense atmospheric absorption, and therefore cannot be used for remote sensing. At shorter wavelengths (0.4 - 2.5um), there are windows where the atmosphere is sufficiently transparent and vibrational absorption bands still occur, although they are clue to overtones and combinations, and accord- ingly are much weaker than the fundamental features. Shifts to longer wavelengths with increasing iron content can still be observed in this region of the spectrum and, with better spectral resolution and sensitivity, it may be possible to monitor subtle variations in chlorite chemist by remote sensing techniques.

Jan 1, 1987

The mIning operations of Bougainville Copper Pty. Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea.C.R.A. Exploration Pty. Limited first established mineralization in the Panguna area in 1964. Exploration work since then has established ore reserves estimated to be 900,000,000 long tons of ore assaying 0·48 per cent copper and 0·36 dwt/ton gold. An economic feasibility study completed in July, 1969 enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons/day. The concentrate will be pnmped as a slurry through a 16 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 MW steam power station, and access roads.

Jan 1, 1971

By Avraamides J, Ritchie I. M

Gold Tellurides are important sources of gold at Kalgoorlie, Western Australia, Cripple Creek, Colorado and Vatukoula, Fiji. Unlike free gold, the tellurides of gold are rather refractory and the usual treatment practice has been to oxidize the tellurides, either chemically or by roasting prior to cyanidation of the liberated free gold. There is a large measure of disagree- ment as to the actual cause of the refractory nature of gold tellurides. In order to investigate the leaching chemistry of gold telluride, a study was undertaken on the thermodynamics and kinetics of its dissolution using electrochemical methods. From this study suitable direct leaching condi- tions are suggested. In acidic chloride solutions gold telluride can be leached using iron(III) as the oxidant. At lower acid concentrations the reaction is controlled by the formation of a passivating film of H2TeO3. In alkaline solutions containing cyanide the rate of gold telluride dissolution increases with increasing pH and strength of oxidant. However, this can result in excessive consumption of cyanide in the presence of stronger oxidants.

Jan 1, 1991

By Likar J, Janexic S, Zigman F

When driving mine roadways in the vicinity of tectonic disturbances and fault zones, sudden outbursts of gas, along with ejections of fine coal, occur. Substantial dynamic changes occur around the roadways in the coal and around the support. The problem has several aspects. Studies have been carried out on the technical analyses of the phenomena which occurred in the Velenje Lignite Mine from 1957 to 1988. The second part of the investigation involves systematic laboratory studies of strength and deformability characteristics of lignite samples and "in-situ" measurements of stress changes during the driving of some roadways. Analyses of events (using the model of limit convergence and the finite element method) showed the possibility of gas outbursts, taking into account the deformability conditions when crossing over from compact lignite to the disturbed region. The rate of advance of roadways and the method of support strongly influence the occurrence of the phenomenon. The preventative measures used in driving roadways under such conditions include trial drilling and the use of blasting instead of machine cutting.

Jan 1, 1992

Mining companies in order to compete and succeed in being viable business propositions must look to the future and select mining methods which guarantee improved efficiency and productivity as well as lower costs.A mining company in adopting a method of mining must now select the equipment most compatible. To some mines compatible equipment may mean the use of drilling jumbos to replace hand held rock drills or the use of load haul dump units to replace scrapers. To other more mechanized mines compatible equipment may mean the use of raise borers and road heading machines. The right decision will be where equipment compliments method in such a way that the working environment is improved, productivity is maximized, cost if reduced and all profit opportunities are optimized. An example of such is where the use of improved mining techniques in underground operations may see cut off grades reduced. By selectively mining these lower grade orebodies, smaller operation's ore reserves improve and the capacity for continued growth is enhanced.

Jan 1, 1990

By Godresse M, Turczynski G. P J, Driver I. J, Low G, Ozawa N

Geological evaluations of coal deposits have been traditionally undertaken in a somewhat manual manner. Information is collected downhole by chip sampling, coring and using downhole geophysical logging. This information is then interpreted by an experienced geologist to define the coal and noncoal lithological units. Coal units were subsequently correlated to provide data for structural modelling. In recent years a number of advancements in interpretation techniques have been made based on Artificial Intelligence. This paper describes an integrated geological interpretation system based on maximised use of Al techniques. The first part describes the lithological interpretation which uses a number of boreholes with both logged lithology and downhole geophysical logs. This information provides a learning set of data to the neural network. The second part concentrates on the correlation of both coal and noncoal units from borehole to borehole. Problems in this area, in a manual sense, are interpretation of correlation across weathering zones and other geological anomolies. The technique is based on pattern recognition and dynamic programming techniques where a correlation matrix is developed relating all holes with their maximum correlations.

Jan 1, 1995

By West-Sells P, King J. A, Patel C

The Eskay Creek orebody is located in north-central British Columbia (Canada). The ore contains major gold and silver values and minor but economically significant quantities of zinc. The refractory nature of the gold necessitates a pressure oxidation pretreatment prior to cyanidation. After solid-liquid separation the oxidation solution can be treated by oxyhydrolysis for iron removal and cementation with zinc dust for noble element removal. The resulting solution, as obtained in pilot studies, contains 7 - 10 g/L Zn, 0.5 g/L Ca and 2 - 4 g/L Mg. Minor amounts of cadmium, copper and iron may also be present in the solution. Over 90 per cent recovery of zinc from Eskay Creek oxidation solutions could be obtained by four stages of zinc extraction with Cyanex 302 extractant (Cyanamid Canada Inc, Niagara Falls, Canada). Zinc was stripped from the organic with spent zinc electrolyte in two stages. A complete description of the bench scale and miniplant studies of the solvent-extraction electrowinning circuit follows. The behaviour of minor amounts of copper, cadmium and iron in the circuit is also Discussed.

Jan 1, 1993

By B Chappell

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to be placed in a tailings dam. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electroosmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By P Salmon, M Kennedy

Sun Metals Corporation Pty Ltd (SMC), a wholly owned subsidiary of Korea Zinc Co Ltd (KZC) is a company formed to develop, construct and operate a zinc refinery, 11 km south of Townsville in North Queensland. The project opportunity exists because of on-going consumption growth for refined zinc metal, technological, environmental and economic obsolescence of existing zinc processing plants, and a prolonged ædroughtÆ of new zinc processing capacity under construction. The Project will utilise proven technology developed by KZC at the Onsan refinery in Korea. The Townsville Refinery has been designed to be the most environmentally-friendly zinc refinery in the world, and in particular to resolve the issue of secure, long term treatment of the ironbearing content of the zinc raw materials.

Jan 1, 1998

By M Nehring, M Kizil, P Knights

Mining and beneficiation can be described as sequential processes of separation of valuable minerals from waste. There is a great deal of interest in how the industry can be more effective – and efficient – with these processes. In particular, many mining companies are looking towards digital technologies to improve precision mining practices; that is, the targeted identification and separation of valuable ore from waste during the mining process. Greater precision will help unlock the value in many complex orebodies that are currently considered Tier 2 or 3 deposits. CITATION: Knights, P, Kizil, M and Nehring, M, 2018. Selection of precision surface mining methods for complex metalliferous orebodies, in Proceedings Complex Orebodies Conference 2018, pp 31–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

This paper looks at the problems associated with surface settlements and other subsidence effects from the underground extraction of coal in relation to consent applications under the Resource Management Act. The main features of subsidence are examined with respect to identifying the adverse effects as defined under the RMA. Particular attention is paid to sites where little or no data is available as in the case of greenfield sites or at mines where new or different mining methods are being introduced. In these situations it is not possible to make accurate predictions of settlements or strains and therefore other factors need to be considered. The long term effects which might occur post mining are examined in relation to mitigation and management options.

Jan 1, 2003

Peraluminous metamorphic rocks may form from a variety of protoliths by a range of processes. Stratiform bodies of such rocks are relatively common in the Precambrian, but less commonly, also occur in the Phanerozoic. The protoliths of such stratiform bodies may have been regionally deposited chamosite-rich sediments, with varying amounts of clastic component, or may have resulted from the in-situ depositional or diagenetic alteration of volcaniclastic sediments, ranging in composition from rhyolite to basaltic andesite.Stratiform peraluminous metasediments, especially those of low to medium metamorphic grade, and relatively iron rich, may be genetically associated with, or be the host rocks for, a variety of styles of mineralization, especially for the ores of An, Ag, Cu, Zn and Pb.

Jan 1, 1990

After 15 years of operation Australian Mineral Foundation is at the cross-roads: Affected significantly in its last 21 years by Australian dollar devaluation, lower mineral industry activity and severe cut backs in the petroleum industry due to the low oil price, a re-evaluation of its goals and industry support is urgently needed. Industry support, strong at the start, has not kept pace with inflation and expectations of a totally self supporting organisation have proved impossible to sustain. Nevertheless, with a change in emphasis in education programmes, continued creative development of information services and more particularly greater awareness by industry of the services available and hence greater use of the services, industry support is expected to increase. Indeed, industry, it is believed, will accept its responsibility.

Jan 1, 1986

By K McCaffery, R P. Halomoan

Two column flotation cells have been installed as single-stage rougher cleaners at Batu Hijau. The objective was to provide additional residence time in the cleaner circuit to maintain maximum recovery during high mill throughput and high feed grade periods. Installation of the columns has allowed the relatively coarse, well-liberated rougher concentrate and the relatively fine, low-grade scavenger concentrate to be treated separately, improving metallurgical performance in the cleaner circuit. Plant results show that the columns produce a high-grade concentrate at an average stage copper recovery of approximately 80 per cent. There is also indication of increases in both overall plant copper recovery and final concentrate copper grade. In addition, the operability and stability of the cleaner circuit has greatly improved.

Jan 1, 2007

The safety in pillar extraction is closely allied to the design features of the pillar extraction system. Considering the conventional supported systems of pillar extraction there are problems associated with complying with the design system outlined. The accident causing agencies and the legislative action to overcome them are im- portant aspects. There is merit in the regularity of support and the limiting of the effects that human error can cause. But new problems and hazards are introduced by this powered support equipment. The comparison of accident experience is difficult due to lack of records and lack of uniformity of approach, but it is clear that powered supports provide a safer system. Every progress in research and practice provides further data to employ in accident prevention.

Jan 1, 1974

Pajingo Gold Mine Pty. Ltd. is a subsidiary of its United States of America parent the Battle Mountain Gold Company. Battle Mountain Gold Company was created in August 1985 as a spin-off of the United States of America Pennzoil Company's gold interests.Pajingo Gold Mine Pty. Ltd. currently has its headquarters and base for operations located in Townsville, Queensland. The Company's main current activities are the exploration and evaluation of the Pajingo Gold Property situated some 50 kilometres south-east of Charters Towers and in the northern Drummond Basin.The discovery of the Pajingo gold mineralisation by the Company was the indirect result of a regional program established to evaluate Carboniferous age volcanic plugs in north Queensland for gold mineralisation.

Jan 1, 1986

This paper will discuss Fordertechnik dawatering screens and their application in process industries. Fordertechnik screens were designed for the dewatering of deslimed, wet fines materials encountered in the mineral beneficiation, sand and coal processing industries. However, these screens have also been used in such industries as municipal waste treatment, paper pulp, chemicals and the food industries. Fordertechnik screens are of simple design and, as a result, offer low capital and maintenance costs. The design is based on the use of twin counter-rotating vibratory motors which provide high frequency, low amplitude linear movement of the screen deck which is essential for high production requirements. Fordertechnik dewatering screens are engineered and manufactured in Australia by Mitchell Cotts Engineering under licence to Fordertechnik GmbH of Mulheim, West Germany

Jan 1, 1984

By M Chappell

This paper describes the design of the steel fibre reinforced precast concrete (SFRC) segmental lining for the intake and discharge tunnels for the Gold Coast desalination plant in Queensland. In addition, the key design requirements and design methods for the lining of these 2 km long, 2.8 m internal diameter tunnels, including structural, durability and maintenance requirements are discussed. Details of the segment configuration and erection process are presented along with information on the manufacture and trial testing of the concrete for the segments. The paper also gives a brief introduction to steel fibre reinforced concrete behaviour. Construction of the tunnels commenced in April 2007, and the authors believe this is the first application of this technology in Australia.

Jan 1, 2008

By Komosa T

The increase in the proportion of sulphide ore treated by the gold mining industry has led to generally higher oxygen requirements. Additions of pure oxygen, hydrogen peroxide and in some cases calcium peroxide, have been proposed as a means of satisfying the oxygen demand and overcoming the problems from reactive sulphides in the ore. Current oxidant addition options and practice are reviewed.Laboratory oxygen demand tests are reported for a suite of ores to show some of the effects of pH and preaeration.Laboratory leach tests at high and low dissolved oxygen levels are reported on two of the ores with higher oxygen demands, and the results are assessed in terms of gold leaching kinetics, ultimate gold extraction, and cyanide requirements.

Jan 1, 1992