Search Documents

By M Darby, B Burdett, F Lovell

The results of the process control improvement project aimed at improving the quality of Australian Bulk MineralsÆ (ABM) iron ore pellets produced by four vertical shaft furnaces are very positive. These results are achieved through process stabilisation and optimisation, improvement in process monitoring and taking early corrective actions when operating variables were outside the target ranges. A number of benefits are obtained from this project. These benefits include: More consistent and improved pellet quality. The average cold compression strength (CCS) value of pellets produced during the eight-month trial is 260 kg/pellet, which is 16 kg/pellet higher than that produced during the 12 months prior to the trial (244 kg/pellet). Reduction in the heat input by eight per cent, from 727 MJ/tonne to 668 MJ/tonne. Reduction in bentonite rate by six per cent, from 7.1 kg/tonne to 6.7 kg/tonne. Increase in the furnace throughput rate by four per cent and additional production of 10 000 tonnes per annum through process stabilisation. Better understanding of the process behaviour. This knowledge is valuable not only for setting the target operating conditions but also for developing the ABM expert system to control the process.

Jan 1, 2005

Trucks are the primary means of bulk material transport in Open Pit hard rock mines worldwide. They are considered to be the most- flexible system available. The large number of trucks used in some mines provides flexibility. Spare units allow for the reduced availability of the single units. Trucks have however very poor energy efficiency. Only 40% of the consumed energy is for transport of the payload, the remaining energy is required to move the dead load of the trucks. With the increase in cost, pressure, mine operators are now looking for alternative methods to make their operation more economical. Energy conservation and increasing haulage distances and uphill haulage are major factors in many well established operations. New methods have already proven themselves as more economical alternatives. Belt conveyors are an alternative means of transport with much higher energy efficiency. They use up to 80% of the consumed energy for transportation of the payload. Energy costs for conveyors are 30% of the energy costs for trucks on level transport and as little as 15% for elevating payloads. Belt conveyors require much fear spare parts and wear components than trucks. A factor of one to two times applies for level transport and ten to twenty times for uphill transport.

Jan 1, 1986

Through the stress synthesis of many examples of macrostructure in the middle of China, it can be concluded that in the middle of Chinesetectonics there are two compression-torsion-forces, one of which ( from NW to SE ) came from the northwest side of Aerjinshan abyssal and giant fault("F1A", see Fig.7,8,9 ); the other (from S to N ) came from the south side of the north piedmontal fault of Kunlunshan-the south piedmontal fault of Qinlingshan ("F2K-F2Q", see Fig-7,829 ).Owing to the two compression torsion forces a new special type of structure named rotation-apart structure occurred from Chaidamu basin to Hebai, Henan, Anhui plain,from Caledonian movement, Hercynian movement,Yenshan movement to Himalayan movement, step by step In the north of Qilianshan during the late Caledonian movement: during the Hercynian movement it extended into a vast area including the Chaidamu basin and Eerduosi basin; during the Yenshan movement it spread over the whole area of Helanshan,Eerduosi basin and Hebai , Henan, Anhui plain. In the period of Himalayan movement all these structures revived .The rotation-apart structure controlled the distribution of all mineral deposits and also were the mineralizing structures.The relation between these rotation-apart structure and earthquakes is very close.

Jan 1, 1990

By P Mackenzie, S Askraba

Pyritic black shales present several challenges to mining operations due to their reactivity. The risk of predetonation of explosives in blastholes, spontaneous combustion of fractured rock and the generation of acid rock drainage must be managed for safety, operational and environmental reasons. At the Mt Tom Price iron ore mine there is a need to differentiate between reactive and non-reactive shale in order to assess risk and make decisions on materials handling. The current approach uses a combination of stratigraphic information and sulfur analysis of blasthole samples. The time taken for sulfur analyses can be a constraining factor on mine production. A new instrument developed by ANSTO Minerals overcomes some of the current limitations on material characterisation. The IOR MeterÖ measures the intrinsic oxidation rate (IOR) of samples of broken rock by circulating air through a sample and monitoring the oxygen concentration over time. The intrinsic oxidation rate is given by the rate at which oxygen is consumed per unit mass of sample, in units of kg(oxygen) kg-1(sample) s-1. Up to eight samples can be measured simultaneously and the turn-around time can be less than 12 hours. Initial trials of the IOR MeterÖ were undertaken at the Mt Tom Price mine in July 2004. The measured IOR of samples from a blasthole pattern spanning different geological layers containing black shale, correlated strongly with the expected reactivity of those layers. The correlation between position in the geological sequence (detailed stratigraphy) and IOR MeterÖ results were much stronger than that between stratigraphy and sulfur content. The new characterisation technique offers the prospect of improving the ability to identify and predict the behaviour of reactive black shales and to differentiate more precisely between different materials. Mine planning, operations, safety and environment all stand to benefit from the success of further trials of the technique.

Jan 1, 2005

By S Johnston, L Howe, S Stevens

Regulators have an important role to play in fostering and enabling reliable, effective, environmental management. Given this, it is perhaps surprising that there has been relatively little debate on exactly how regulators can enhance their own approaches, in order to promote improved outcomes overall. The authors argue that applying research on High Reliability Organisations, as well as the University of Pennsylvania’s Penn Program Framework for Regulatory Excellence, to regulators has the potential to facilitate positive environmental results across the mine life cycle.

Aug 2, 2023

By J-P Franzidis

Mill operators have traditionally been forced to rely on grade-recovery curves and overall flotation rate constants when analysing proposed improvements to plants. This has led to loss in money and time when a proposed change that showed potential in laboratory scale tests failed to show improvement in the plant. Frequently, this is a result of the operators being unable to gain insight into how and why the proposed change affected the flotation performance. This is due to the classical models not including any description of the subprocesses of flotation and their individual contribution to the overall flotation performance. A new flotation model has been developed as part of the AMIRA P9 project that separates the flotation process into subprocesses and includes the contribution of both the pulp phase and froth phase to the overall flotation recovery. It is not possible to determine the individual components of this new model on traditional pilot plants as they lack the required flexibility and scale. Therefore a new pilot plant has been developed known as the Floatability Characterisation Test Rig (FCTR) that has the flexibility and features required for the determination of the flotation subprocesses. The flexibility and features of the FCTR also make it an ideal tool for investigations into many different aspects of flotation research. These include the effect of reagents, grinding, and power on the flotation performance. This paper will describe the methodology for using the FCTR in these fields of research and highlights the advantages of using the FCTR over traditional methods.

Jan 1, 2000

This paper describes the new legislative regime that will apply to the regulation of the minerals industry in New Zealand.The reform of New Zealands minerals legislation was initiated in January 1988 when the Minister for the Environment, Rt Hon Geoffrey Palmer, announced the Governments intention to review all the major laws governing New Zealands resources. The Resource Management Bill is scheduled for to the House in December 1989 and its date of enactment is scheduled for June 1990.With some matters still to be determined (at the time of writing), this paper cannot be a definitive review and description of the new legislation, it is instead an attempt to outline the major features of the Bill, to date, that are seen as important to the mining industry.

Jan 1, 1990

By Belcher C. B

A simple gravimetric procedure was developed for the rapid determination of carbon dioxide in coal mine roadway dust samples and the result is used for the subsequent calculation of incombustible matter contentaccording to the requirements of the Queensland Coal Mining Act. The carbon dioxide is determined through loss of mass by a semi-enclosed apparatus, following room-temper.ature hydrochloric acid attack on the sample.With a sample containing 36 per cent carbon dioxide, the achieved standard deviation (ls) of 0·3 per cent CO. is adequate for coal mine roadway dust analysis.This simple procedure enables relatively unskilled labour in mine laboratories, to analyze coal mine roadway dust samples in accordance with the Act. Some 50 analyses can be achieved per day compared with 8 by the Australian Standard Method for coal.

Jan 1, 1976

This report chronicles the historical development of longwall mining in the United States and speculates on future developments to the turn of the century. Five eras of technological development during the modern period are described and analyzed. These eras discuss the development of (1) mechanized extraction, (2) self advancing roof supports, (3) high capacity roof supports, (4) shield supports, and (5) system automation. Current trends are analyzed in terms of: longwall utilization, production capability, support capacity, face widths, and new technological developments. From these analyses, the future of longwall mining to the year 2000 is speculated. It is concluded that longwall mining will continue to grow in importance during the next decade and that the next major technological milestone will be the realization of a fully automated longwall mining system.

Jan 1, 1992

By Williams D. J

The boundary element method is one of a number of tools that have found wide application in geomechanics for mine design and stress analysis. Two examples are presented in this paper, illustrating the use of the boundary element method to find potential problem regions in large-scale excavations. These examples are from a Papua New Guinea open cut mine and an Australian sub-level caving operation. Because of the scale of the mines and the complexity of the excavations, the boundary element method is the only practical numerical modelling technique to account for the major influences. Although the boundary element method uses only linear elastic models of the rock mass, the paper illustrates techniques for dealing with non-homogenous and anisotropic rock masses, as well as clasto-plastic effects associated with an excavation.

Jan 1, 1995

The Mons Cupri Cu-Pb-Zn deposit is situated within a complex Archaean volcanic sequence dominated by rhyolitic fragmental rocks. This sequence is underlain by a 150 m group of rhyolitic ash flow tuffs with minor conglomerate and sandstone, and is overlain by approximately 180 m of dacite and andesite flows. The Mons Cupri sequence itself consists of several elongate or circular rhyolite domes, flanked by rhyolitic fragmental rocks ranging up to 400 m in thickness away from the domes. The lithology of clasts (typically 1 cm to 1.5 m in size) provides strong evidence that the flanking fragmental unit was derived by explosive eruptions associated with the rhyolite domes. An approximately 15 m thick shale horizon, bleached and silicified at its base, overlies both the rhyolite domes and the frag- mental unit. A south-dipping chloritic pipe-like body, with near-surface dimensions of 1,000 by 250 m and narrowing at depth to produce a cone-shaped cross section, lies within the rhyolitic frag- mental rocks about 250 m north of the largest rhyolite'dome in the Mons Cupri vicinity. Its east west elongation parallels that of the rhyolite dome. Ghost fragments indicate that the material in this fissure is a severely chloritized derivative of the rhyolitic frag- mental unit. The chloritic pipe is overlain

Jan 1, 1973

By A M. L Smith, W E. Dubbin, K A. Hudson-Edwards

Jarosites (KFe3(SO4)2(OH)6) are examples of minerals that are highly effective scavengers of toxic elements, and are abundant in acid rock drainage systems, acid sulfate soils, metallurgical wastes and other contaminated sites. The K, Fe and S sites can be filled by toxic elements such as Cd, Cu and Zn, but the mechanisms of this incorporation are not well understood.We have used atomistic simulation methods to model the jarosite (102) surface and its interactions with Cd, Zn and Cu, in order to understand the mechanisms by which these potentially toxic elements are incorporated into the K-jarosite structure. Our results suggest that incorporation via a defect complex consisting of an impurity cation at the K site charge balanced by a K vacancy stabilises the (102) surface in the order Cu>Zn>Cd.

Jan 1, 2008

By Curless JM, Power SG

Polymetallic hydrothermal veins of the Western Cascades are hosted in propylitically altered Tertiary volcanics of calc-alkaline affinity and (or) in nearby, altered, and compositionally similar plutons. Ores from shallow and now abandoned mines produced mostly gold and were considered to be of epithermal origin. However, recent discovery of breccia and porphyry types of Cu-Mo mineralisation and other data suggest that the deposits of this terrane vary systematically both regionally, south to north, and locally, high to low altitudes. The evidence includes changes in (1) size, composition, and complexity of plutons, (2) types of mineral deposits; (3) assemblages of alteration and ore minerals; (4) trace metal geochemistry of host rocks; and (5) fluid inclusion and sulphur isotope data. They collectively imply a consanguineous origin of vein, breccia, and disseminated-veinlet types of mineralisation by magmatic hydrothermal processes.

Jan 1, 1987

By E Widzyk-Capehart

The conventional ammonium nitrate fuel oil (ANFO) loader utilises a pneumatic system to control the flow of ANFO (via rotary actuator/ball valve) and air (via an auxiliary air valve). This system, though relatively simple and reliable, has several drawbacks with respect to ease of control and level of automation. In this paper, a radio frequency (RF) remote control for explosives charging is discussed. The system design incorporates electric solenoid valves to control the rotary actuator and the auxiliary air valve. All operations associated with explosives charging are selectable at the remote and are completed according to a modifiable time sequence. This allows the following charging sequence to be reduced to a single momentary application of the remote:removal of water from the hole prior to charging with ANFO; charging of the hole for a preset but adjustable period of time; and removal of the remaining ANFO from the ANFO hose. A specially developed remote switch allows the operator to maintain two-handed control of the ANFO hose whilst achieving full control of the charge-up process. Failsafe electronic architecture is incorporated into the systemÆs design to increase safety to the highest level. Should the RF remote control fail, a wired remote is included in the system to allow for the charging process to continue, albeit at a reduced level of control. The application of the RF remote control system in an underground explosives charging operation minimises and/or eliminates many problems associated with the use of the conventional charging system. These include: the wet-hole problem, trip and entanglement hazards, air embolism and the two-man loader control requirement. The developed remote control unit proved to be effective at removing water from wet holes leading to increased face advance per drilling operation. It proved to be economically feasible, allowed for an increase in systemÆs dependability and safety factor and for a truly one-man operation which resulted in reduced manpower.

Jan 1, 1999

By R Engle, R P. McMahan, D A. Bowman, S Schafrik, W Thabet

Preventing injuries and fatalities related to conveyor system use in the mining industry is important and increases uptime while decreasing lost time. The research presented here is funded by the National Institute for Occupational Safety and Health (NIOSH), and intended to accomplish this prevention by the use virtual environments (VEs) to improve training and help miners better understand the hazards of working around conveyor systems. Two conveyor system VEs designed to teach miners about hazards and to safely complete tasks around conveyor systems were developed for this project. The first conveyor system VE, called the instructional tour, gives the miner a semi-automated tour of a conveyor system and teaches the miner about possible hazards (eg, missing guarding) and how to safely fix conveyor problems (eg, a stuck idler) using lock-out, tag-out procedures. The second, called the virtual shift, allows the miner to freely navigate around a conveyor system to detect and avoid hazards. The miner is presented with equipment failures that need to be safely repaired during the virtual shift. If the miner fails to identify and avoid a hazard or fix a failure in a safe manner, an animation of the consequences is shown to the miner, who must start the virtual shift over. The models for the conveyor system VEs were created using 3DS Max. Desktop versions of the VEs were then created using Deep CreatorÖ, an authoring application for creating interactive 3D environments. Later, more realistic versions of the VEs were created for CAVEÖ, a room-sized visualisation system, using DIVERSE, an application programming interface. In initial evaluations of the conveyor system VEs, mining colleagues have indicated great interest in such training tools. According to their feedback, these and similar VEs would provide excellent alternatives to normal classroom training and serve as positive precursors to hands-on experience. These VEs provide new miners a chance to experience hazards associated with working around conveyor systems without being in possible danger.

Jan 1, 2008

Commercial explosives range from pure emulsions to pure ANFO, with blends of these providing interesting alternatives: energy is often adjusted through addition of aluminium, or the control of density. The energy rating of explosives is derived chiefly from detonation codes, which are used to derive expressions for the internal energy change of the detonation products as they do work under expansion. While all codes used for this purpose work on the basis of Ideal detonation, it is common knowledge that commercial explosives operate in the Non-Ideal domain, which affects the mode of energy delivery to the environment. However, since Ideality represents the foundation from which actual performance evolves, it is valuable to examine the intrinsic energy release of a formulation before attempting to understand the influence of Non-Ideality. In examining the Ideal pressure profile of fundamental formulations, remarkable correlation has been found with field performance, and this increases understanding of the influence of various formulation modifications, especially in regard to the stage at which energy is released, and the effect on rockbreaking. This work has emphasised the value of attempting to understand and define better the non-ideal detonation process.

Jan 1, 2001

This paper describes the planning mechanism and implementation of a progressive rehabilitation programme at Hunter Valley Mine in the Upper Hunter Valley of New South Wales. Hunter Valley Mine is a large open cut coal mine which produces approximately 7.0 million tonnes of coal (run of mine) annually for export. This production level involves the movement of some 60 million tonnes of waste and coal each year.The rehabilitation programme at Hunter Valley Mine has been developed to provide a combination of pasture, based on improved pasture species and timber belts to enhance the visual characteristics of the rehabilitated landform, whilst creating amenity in the form of shade for livestock.The operational philosophy for the rehabilitation programme is that of progressive rehabilitation. The best time to undertake rehabilitation is now.' As a result, planning for the rehabilitation programme is continuous, so that all site works are completed in time for vegetation establishment during the critical periods each year.

Jan 1, 1992

By Tsuchiya N, Takada Y, Okabe K

Alkalis in the blast furnace are removed mainly by the slag, Alkali removal by the slag was studied as a rate process of alkali vapor- ization from the slag flowing through the dropping zone in the blast furnace. The vapor-, ization rate of I:20 from CaO-Si02-A1203 IZ20 slag was- measured under various experimental conditions. An empirical formula for the vaporization rate was obtained as a function of slag basicity, temperature and surface area per unit mass of slag. A simulation model of IC20 vaporization in the dropping zone was evaluated using the rate equation when the true velocity and surface area of the slag was de- termined from a flow dynamic model of counter- current gas-liquid flow through packed beds. The influence of the dynamic conditions of flow, as well as the slag basicity and temperature, on alkali removal by the slag was estimated.

Jan 1, 1980

By Duran A, Eggers M. J

It is standard practice in geotechnical studies for mine design to drill a series of inclined oriented boreholes into the proposed pit walls. However, this investigation tool is often used without an adequate understanding of the inherent shortcomings in the method and the many potential sources of error. Of the more commonly used orientation methods in Australia the clay imprint technique is probably the most reliable. Contoured stereographic plots of oriented core data are frequently characterised by diverse pole distributions and low concentration maximums compared with line mapping data. Common sources of error producing these poor results are misinterpretation of orientation marks or imprints, inaccurate marking of the reference line, errors in the structural measurement of the defects, lack of continuity information and blind zones sub-parallel to the borehole direction which correction methods frequently do not fix. Line mapping is the preferred method of structural data collection due to the lower overall cost, availability of continuity information and higher accuracy. The projectability of field mapping data to final wall positions can be assessed with a good understanding of the regional geology and local structural patterns. Where field mapping is not possible due to a thick regolith cover, core orientation should be carried out by experienced personnel to minimise the many potential errors.A series of case studies are presented which compare oriented core with mapping and highlight the inherent problems with the technique.

Jan 1, 1992

By D S. Clarke, K B. Sporli

Structure is an important control in the localisation of gold mineralisation in epithermal systems. There has been, however, only limited investigation of the structural elements involved; such a study is currently directed at the gold deposits of the Coromandel Volcanic Zone (CVZ). Here, mineralised veining and brecciation ranges up to tens of metres in thickness. Dips of veins are mostly steep, but not vertical, and there is a significant number of low angle veins. The structural control of epithermal deposits may be considered on four scales. At the mega-tectonic scale, pre-volcanism fault patterns mostly relate to separation of the New Zealand micro-continent from Gondwana. The major structural controls on mineralisation at this scale, however, are associated with the volcanic arc processes responsible for the CVZ. Post-mineralisation faulting are linked to the Hauraki Rift and the Colville Ridge-Havre Trough system. Regional scale faults controlling the distribution of gold deposits are the product of these tectonic events; much of the faulting may relate to rifting and calderas, but further work is required to demonstrate this. Detailed study is also needed on vein systems at the prospect scale to validate models of brittle deformation responsible for such systems. Evidence that a variety of structural mechanisms dominated in different deposits is found at the vein scale, with Coromandel gold deposits being classified according to their different styles of vein-fill texture.

Jan 1, 1990