Search Documents

By E Werner, B R. Leavitt

The chemistry of acidic mine drainage discharging from flooded coal mines is commonly reported to improve with time after flooding. This investigation describes a 18-year dataset of post-flooding water chemistry for a below-drainage underground coal mine within the northern Pittsburgh coal basin (Pennsylvania, USA). The Montour mine is a 5650-hectare below-drainage coal mine of maximum 260 metres depth. Montour was closed in 1980 and flooded to within 38 metres of land surface within 4.8 years. Pumping averaging 210 L/s was then employed to maintain water levels at this elevation. The flooded proportion of the mine (by volume) at full flooding was 56 per cent. The shaft where water was pumped from Montour for water control is located about 70 per cent of the distance between the mine water table and the back of the mine ù that is, it is close to the back of the mine. The residence time (total water volume at flooding divided by pumping rate for control) is estimated at 5.6 years. Time series of chemical analyses show three phases of chemical behavior in post-flooding discharge. In Phase I (zero to two years after flooding), iron concentrations were high and reached their maximum (1100 mg/L). In Phase II (two to four years after flooding), a transition was begun to alkaline conditions, with decline in iron and other solutes. In Phase III (>4 years), net alkaline conditions began, with iron concentrations declining exponentially to 50 per cent of mined volume. This attainment of net alkalinity in this case may have also depended on abundant calcite in overburden extended up to 30 m above the mine floor.

Jan 1, 2003

On the 18th November, 19'58, the first coal was delivered to the Morwell Power Station from the adjacent Open Cut using conveyors for the transport of the coal from the working face to the boiler bunkers. As the cut develops the coal seam will be worked for its full depth of about 360 feet from four benches, each feeding a conveyor line along th.e face and up out of the cut to the power station and briquette factory. By 1970 the estimated maximum daily demand reaches 60,000 tons and the total annual output 18 million tons. The complete conveyor installation will then total some 9 miles with a capital cost of over £3~ million.The choice of conveyors in place of the more usual rail system was made possible by the development of movable belt conveyors which use mechanical conveyor shifting, high belt speeds and flexible high strength belts and the paper deals with these and some other aspects of the scheme.INTRODUCTIONThe development of brown coal deposits is usually based on open cut workings equipped with a few large dredgers giving an almost continuous output of coal or overburden which has to be hauled a comparatively short distance. These are ideal conditions for conveyor operation, and it is surprising that, until recently, rail transport has been used almost exclusively in brown coal open cuts. In some cases inclined conveyors have been introduced to take the coal from the coal levels up out of the cut to bunkers at groundlevel, but trains have been left to operate between the ditch bunker feeding the conveyor system and the dredger.

Jan 1, 1960

By I Haine, J Penm, T Waring

During 1999 there was a considerable turnaround in world prices for most minerals and energy commodities, except for the bulk commodities (coal and iron ore). The main reasons for this turnaround were: improved prospects in demand for most minerals and energy commodities in the Asian region following a return to both economic and industrial production growth in key economies in that region; continued moderate growth in demand in Europe and North America; substantial production cutbacks in a range of minerals and energy industries; effective reductions in the supply of oil by OPEC nations; and an announcement by European central banks that they would cap the amount of gold they sell and loan in the next five years. Most of these influences are expected to be sustained into the first years of the new millennium. In 2000, with exception of coal, average world prices of minerals and metals are forecast to rise significantly. Gross domestic product and industrial production is expected to grow in some European countries and most Asian countries in 2000 and, with moderate growth expected to be sustained in the United States, demand for minerals and energy is expected to increase. AustraliaÆs main bulk commodities, iron ore and coal, saw prices set for 1999 - 2000 at substantially lower levels in negotiations in early-1999. Double digit price cuts were locked in. However, similar falls appear to have been avoided for coal in Japanese Fiscal Year 2001, while increases of between four and six per cent were achieved for iron ore. Forecast modest recovery in economic growth in Japan and increasing demand elsewhere in Asia are expected to lead to tighter market conditions in 2000. Beyond 2000, world minerals and energy markets will be influenced by the expected robust global supply responses of minerals and energy companies, against a background of sustained economic growth and industrial production growth in major consuming countries. Over the medium-term, a return to declining real prices which have been evident for most commodities in the recent past, is expected as exploration, mining and processing technological change and associated productivity growth continues to reduce industry costs. While lower rates of exploration and mining investment in Australia between 1998 and 2000 will modestly constrain the rate of future industry expansion, Australia remains an important contributor to expected growth in global minerals supply over the medium-term. Australian mine production is forecast to grow between 1999 - 2000 and 2004 - 05, boosted by production from recently commissioned mines and minerals processing facilities and comissioning of other projects at advanced stages of planning.

Jan 1, 2000

Severe development difficulties were experienced soon after in-seam mining commenced at Appin Colliery in'1962. Thirteen years later no significant pro- gress had been made in overcoming some aspects of this development problem. Some success had been achieved in destressing roadways both in development and pillar extraction. Longwall retreat mining had shown promise of being highly productive but at an extremely high cost in terms of development requirements both in number of roadways and intensity of support in those roadways. No real advance was made in the problem of driving the first heading of a group of headings under conditions of apparently high stress in directions other than the preferred mining directions, although failure of the roof in this heading did seem to give easier work in the subsequent headings driven particularly if they were driven on narrow centres.

Jan 1, 1976

Broken Hill South Limited's discovery of phosphate deposits in the northwest of Queensland in 1966 prompted intensive exploration which has proved phosphate rock in excess of 2,000 million tons at ten separate deposits.Systematic exploration for phosphate in Australia was initiated by the company in 1964. Early in 1966, an investigation of oil wells in the Georgina Basin in the Northern Territory and Queensland revealed widespread anomalous phosphate in early Middle Cambrian Beetle Creek Formation and Thorntonia Limestone. Phosphorites recognized in oil wells in the southeastern part of the Basin, Queensland, led to the discovery of the Duchess deposits. Exploration of the Beetle Creek Formation since 1966 has disclosed nine other sizeable deposits north of Duchess around the eastern margin of the Basin. The Lady Annie and the adjoining Lady Jane deposits, by reason of their location, 160 miles south of the Gulf of Carpentaria, are expected to be the first to be brought into production.Beneficiation testing and engineering investigations commenced in 1967. Transport between the deposits and various port sites in the Gulf of Carpentaria has been extensively studied and a slurry pipeline as a means of transport to a deep water island port, is now being investigated.

Jan 1, 1971

By Sparrow G. J

In a recently completed AMIRA project, 20 samples were searched for gold mineralisation using the automated location facility (ALF) for rare phases on a scanning electron microscope in the CSIRO Division of Mineral Products, Melbourne. The samples were submitted by mining companies in Australia, and Papua New Guinea, and included crushed ore samples, cyclone overflow and underflow products, a flotation concentrate, and 12 tailing samples. Their gold contents ranged from 600 to 0.2 g/t An. Native gold and gold minerals including a gold telluride, gold-silver tellurides, and a gold bismuth mineral, were located in the samples as free grains and associated with other minerals such as pyrite, magnetite, hematite, ankerite, copper sulphides, silicate minerals, and quartz. In the highest grade samples, both micron sized and 200 ¦m grains of gold were found with ALF. It would be difficult to locate such d wide size range of gold in a manual search. Gold mineralisation was located in the tailing samples assaying 0.4 g/t An and higher. In several tailing samples coarse grains of native gold over 40 p.m in size were located. One grain was estimated to have contributed 40 per cent of the gold in the sample. As well as locating gold mineralisation, the ALF examination resulted in the identification of uranium, mercury, and bismuth minerals in the samples. Knowledge of the distribution of these minerals in processing streams could be important in the operation of a concentrator.

Jan 1, 1992

By D Sinclair

Sustainability will become a more stringent issue in mine planning over the next 40 years. The evidence of this is apparent in State and Commonwealth government policies now emerging in respect to water, green house gases, waste and other process emissions. The mining industry has developed policies such as æEnduring ValueÆ, which go some way towards establishing a framework within which mining can continue to be an underpinning strength within the Australian economy. However, the demands of new policies are directed at extending sustainability in ways that will change the way in which projects are implemented. This paper examines the nature of new policies aimed at water, energy and emissions, considering examples of where mining practices have or may change in order to meet new objectives in resource efficiency. Important issues will, as always, be the international price competitiveness of the mineral resources being produced but, where this is now devolved around mining and processing costs, these costs may in the future be strongly correlated to the nature and cost of local energy resources compared with those in Australia, the ability to mitigate and minimise water resource use and environmental impacts deriving from emissions and the veracity of competitor nations in meeting the same standards of performance in resource efficiency usage and in emissions control. As these systems bed down internationally mining in Australia will need to concentrate, amongst other things, on finding higher grade orebodies and on better technologies to release the value of lower grade ores. For our mining industry to remain strong, greater expenditure will need to be focused on these objectives. Finally, it will be important for the industry to remain vigilant and proactive in directing government policy development to ensure that practical objectives in mining are not curtailed unnecessarily through ignorance of mining market precepts developed over the centuries of mining operations.

Jan 1, 2008

Magmatism is of first order significance in the extension process. Continental extension is terminated when sea-floor spreading commences, but sea-floor spreading will not commence if magmas do not begin to arrive in sufficient volumes. In the oceanic lithosphere, the rate of magma supply may determine whether sea-floor spreading takes place, or lithospheric extension as the result of normal fault arrays. In continental crust thickened as the result of previous compressional orogeny, the availability of magma may determine a completely different process. The author has examined metamorphic core complexes in a number of tectonic environments, in the North American Cordillera, in the Aegean Sea, Greece, and in the Solomon Sea, Papua and New Guinea. What these terrains have in common is a major collisional orogeny predating a major extensional event. The "roll back" of the lithospheric flexure associated with subduction can be seen as the "driving force" for extension in two of these cases. Metamorphic core complexes in these environments are characterized by domal exposures of crustal scale ductile shear zones, underneath which massive plutonic complexes have been formed. Emplacement of these plutons is associated with anatexis of the surrounding rocks. Migmatite complexes are well developed in the Aegean and Solomon Sea core complexes, and in some core complexes in the Basin and Range. Chains of core complexes can be explained as the result of basaltic and andesitic magmas derived from a linear belt of relatively hot rising asthenosphere, in a zone of attempted continental "break up". It is argued that core complexes are the results of magmas derived from relatively short lived mantle "hot spots" impingeing on extending continental crust which has been overthickened during previous compressional orogeny.

Jan 1, 1990

Education for the Mineral Industry in Australia developed in an uncoordinated but effective fashion till the mid 1960's, with recognised quality in graduates, with output matching demand, and with industry needs being fulfilled. Then in the space of a further 20 years, as company structures expanded, as the number, complexity, and costs of mineral projects escalated, as educational facilities, costs and politics increased, as community perceptions and aspirations changed, as government control of minerals and education increased, and as mineral sales cycles and markets fluctuated widely, the very fabric of Australian Mineral Education fell in tatters. Extractive Metallurgy Education suffered most in this collapse, and no compre- hensive remedies have been initiated. We are all the losers. In the 1990's, the extraction of Australian minerals and metals will increase in international significance, and the education of Extractive Metallurgists must meet this need. After examining the current situation, a series of management strategies are proposed to enable Extractive Metallurgical Education to survive and prosper in the next two decades and beyond. These strategic proposals involve industry, the government, the educational bodies, and individuals, in a range of short and long term objectives, policies, and actions.

Jan 1, 1984

More than ten seafloor massive sulfides (SMSs), which tend to be enriched in Au and Ag with varying amounts of Zn, Pb and Ba, have been reported in Japanese Exclusive Economic Zone (EEZ) including the Jade hydrothermal field in the Izena cauldron Okinawa, theSunrise deposit in Myojin knoll Izu-Ogasawara, and other active deposits found in the past 20 years. From the fiscal year 2008 some universities in Japan will begin development of sensing devices to delineate surface distributions of known SMSs and to find new ones. The devices would be deployed by an autonomous underwater vehicle (AUV) or remotely-operated underwater vehicle (ROV) later in active hydrothermal fields and potential areas in the EEZ. On the other hand, different laboratories are planning to research and evaluate SMSs with state-of-the-art methods such as the benthic multi-coring system and geophysical devices to collect information in deeper parts of the SMSs. In this session recent projects on exploration and evaluation of SMSs with some new trials including geophysical and geological surveys in Japan will be reported. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Forty two new apatite and zircon fission track analyses on the Kubor-Marum-Bena Bena area of northern Papua New Guinea severely constrain the timing of tectonic events and hence the tectonic models for New Guinea, particularly arc-continent collision. In addition, the data can be analysed regionally in terms of known and assumed lithospheric fault zones inferred to control mineralisation (eg. Corbett 1994; Kendrick et al 1995; Hill et al 1996) to determine reactivation of these zones. When combined with the new kinematic plate models for the evolution of New Guinea (Hall 1997) there is the potential to predict likely zones of mineralisation. The low-medium grade? Palaeozoic rocks of the Bena Bena terrane yielded a zircon fission track age of 17 Ma, indicating the time of cooling below 200¦C. The age is consistent with `the shift, at about 16-18 Ma, from volcanolithic sediments to mixed provenance sediments rich in quartz and metasedimentary lithic fragments in the southern Finisterre Ranges (Abbott et al. 1994). This shift was recorded in the Sukurum Formation, which ranges in age from Middle Miocene to Pliocene with quartzose and metasedimentary grains in all samples. Although recording rocks at temperatures of 200¦C and hence depths of ---5km, the 17 Ma age suggests the Bena Dena terrane was rapidly cooling at that time due to uplift and erosion, supplying metasediments to the southern flank of the Finisterre Range, currently 100 km to the east. Significantly, the Middle Miocene Akuna Intrusive Complex, dated 14-17 Ma by Page (1976), lies almost entirely within or adjacent to the Bena Bena terrane. Potentially the uplift, erosion and cooling of the terrane at 17 Ma may have been caused by the rising plutons. If so the 800 sq km exposure Akuna Intrusive Complex at the SE end of the Bena Bena terrane may have been the focus of uplift and supplied the metasedimentary detritus to the Finisterre Range. This suggests that the Finisterre Range was not far removed from the Bena Bena terrane, perhaps less than the 200 - 400 km indicated by Abbott et al (1984). The Akuna Intrusive Complex probably resulted from subduction of the Solomon Sea Plate beneath the PNG margin. In order for the subducted slab to reach depths of -100km below the area to facilitate partial melting and plutonism (Hamilton 1994), subduction probably commenced 3-5 Ma Ma before plutonism, ie at or prior to 20 Ma suggesting a significant change in the tectonic regime at -20 Ma, perhaps related to collision of the Solomons - Ontong Java Plateau collision (eg. Hall 1997). The main result to emerge from the 28 apatite fission track analyses is that the whole of the study area underwent rapid cooling due to uplift and denudation in the Late Miocene, mainly between 7-10 Ma. Results from several samples indicate that they were not totally overprinted prior to uplift indicating maximum burial of -3 km in the Middle Miocene, assuming normal temperature gradients. The burial is less if higher gradients are assumed, allowing for Middle Miocene plutonism. The Late Miocene cooling in the Mobile Belt agrees well with the Pliocene to Recent cooling in the Fold Belt to the SW, interpreted to be due to uplift and erosion associated with fold and thrust deformation of the Miocene Limestones (Hill & Gleadow 1989). This timing relationship suggests, that compressional deformation in the Mobile Belt occurred in the Late Miocene, at 105 Ma, and that the deformation migrated towards the undeformed foreland in the southwest in the Pliocene, at 5-2 Ma. The regional Late Miocene uplift and denudation in the Mobile Belt is also consistent with that postulated by Crowhurst et al (1996; 1997) for northwest PNG, although they considered the event to have occurred mainly from 8-5 Ma. If so, then the uplift and denudation may have been migrating from east to west as well as to the south into the Fold Belt. These timing relationships place significant constraints on tectonic models for the area, indicating that the major compressional pulse in PNG commenced in the northeast at -10 Ma and migrated to the southwest and west in the latest Miocene to Pliocene. This suggests that the initial arc-continent collision and associated shortening occurred in the Late Miocene around -10-12 Ma. This immediately followed intrusion and cooling of the Akuna Intrusive Complex at -17-14 Ma and the Bismarck Intrusive Complex at -12.5 Ma (Page 1976), indicating a linkage between the end of plutonism and the start of compressional deformation. The timing is consistent with the observation of Hamilton (1994) that in areas of subduction `the common regime in overriding plates is extensional and leading edges are crumpled only in collisions. This suggests that the Middle Miocene magmatism in northern New Guinea occurred during extension above a subducting slab and was terminated by Late Miocene arc collision and resultant compression commencing at -10-12 Ma. In general, these data indicate that the acme of denudation and cooling in the Mobile Belt was in the Late Miocene, with relatively little denudation there since. In contrast, Hill & Gleadow (1989) found that the peak of denudation in basement outcrops in the Fold Belt was in the Pliocene at -4 Ma. However, in this study some samples from the Mobile Belt yielded Pliocene ages or high

Jan 1, 1997

By Whittaker B. N, Reddish D. J

The rockbolting method of support is employed widely in several countries in different of mines. Hard rock mines use this method extensively. Soft rock mines, such as coal mines, have employed standing supports (steel sets) as the main method, although some countries such as the U.S.A. and Australia have preferred rockbolting. There is increasing interest in extending the rockbolting method in coal mines. The application of rockbolting techniques in an industry which traditionally has not applied such techniques, has required the development of a systematic design approach. This design approach uses extensive monitoring, to asses the viability of the support system in differing conditions. Currently at a number of new and existing mine developments in the U.K., rockbolting is being successfully applied. Although, inevitably some localised geotechnical problems have been encountered and have needed to be taken into account. The effect of faulting on roadway conditions is discussed in this paper and a design approach has been applied using a numerical analysis method, namely the Finite Element Method. The results presented in the paper serve as a useful guide to roadway support designers, and in particular the role played by different bolts in a range of conditions.

Jan 1, 1992

By Kohra A, Shoji S

The amount of copper production by flash smelting process occupies about 17% (equivalent to 1.4 million t/year) of total free world production. In Japan, 650,000 tons of copper is produced annually by flash smelting. This is 65% of the gross copper production of Japan. To reinforce pollution control, promote energy saving, and enhance production efficiency by increasing the size of furnaces, conventional blast furnaces and reverberatory furnaces are being replaced with the flash smelters worldwide. The Ashio Smelter started copper production in 1884 and developed in association with the Ashio mine. In those days, the Ashio smelter produced copper by using the blast furnace process designed for the high-grade ore from the copper mine. At that time, this process was specialized in Japan. In 1956, for the first time in Japan, the Ashio Smelter introduced the flash smelting process developed by Outokumpu Oy of Finland (it is suitable for treating the copper concentrate, producing sulfuric acid and improving production efficiency). The flash furnace in Ashio, the first ever in Japan, had a capacity of 230 t/day for copper concentrate and was operated up to 1962. During this period, various operational troubles were solved, and further improvements were made; and, in 1962, a Furukawa-type flash smelting furnace was completed in Ashio. This improved version of a flash furnace had a capacity of 450 t/day. There was one flash furnace and one waste heat boiler, which were arranged in a unique pattern for that time. This furnace may be said to be the prototype of the present flash smelting process in the world.

Jan 1, 1987

By E Kunz

Decreasing the gas content in the worked seam by degassing before the start of winning has proven its worth in some areas of German hard coal mines. On the one hand, it removes the risk of gas/coal outbursts and on the other hand it reduces the gas inflow into the longwall. The underground experiences of the last 30 years have led to a æhit listÆ of coal seams with respect to their suitability to predegassing. Trials in the DMT laboratory and also results gained in the deposit show that the suitability of a seam for predegassing depends on its rank. In seams with volatile matter of 20 - 30 per cent, high efficiency ratings are achieved as a rule, with lower ratings both in seams with lower and with higher content of volatile matter.If the rock pressure is unusually high, the efficiency rating of the predegassing is lower, even in seams which would normally be suitable for this process. Under unfavourable conditions, for example below or above residual pillars, in-seam boreholes cannot be drilled successfully and the method is not practical. But if the worked seam was already stress relieved, the predegassing has an optimal efficiency. Latest investigations show that the distance between the in-seam boreholes can be extended. But in that case, the time necessary to reach the same reduction of the gas content increases considerably.

Jan 1, 2005

The accepting of the geologist as part of the mining industry team has only become a reality in the last fifty years in Australia. Commencing in the 1920's it received a check in its progress during World War II. Since then it has had its highs and lows to extremes not hitherto experienced. The recent mining boom and the succeeding slump have provided opportunity to examine more critically and positively the role of the geologist in the mining industry. The future is examined, not in crystal ball fashion, but in terms of selected specific aspects. Suggestions are offered concerning these aspects.

Jan 1, 1976

By R Herbert, M E. Malmstr÷, S U. Salmon

The study focuses on sulfide oxidation processes in unweathered pyrite-rich mine tailings from a soil-covered impoundment in northern Sweden. To simulate the oxygen-limited conditions in water saturated tailings two long-term column experiments were performed. Results are presented for the first 11 months of the experiments at room temperature. The tailings used in the experiments were of two different grain sizes (one coarse grained, in the range 0.02 - 0.6 mm with a grain surface area of 1.86 m2 g-1, and one fine-grained, in the range 0.0015 - 0.06 mm with a grain surface area of 10.00 m2 g-1) and with slightly different mineralogical composition. The S:Fe molar ratio in the leachates (1.0 - 1.5) indicates either that pyrrhotite is the main iron sulfide undergoing oxidation in our experiments, or, alternatively that the S:Fe molar ratio in the leachate is determined by pyrite weathering in conjunction with other processes releasing iron or immobilising sulfate. However, speciation modelling of the leachates indicates that ferrihydrite was close to saturation, suggesting that a ferric oxyhydroxide may have dissolved/ precipitated during the experimental period, thereby affecting the S:Fe molar ratio. Pyrite oxidation rates obtained from the two column experiments during æsteady-stateÆ were 2.25 + 10-13 and 8.45 + 10-14 mol m-2 s-1 in the coarse and fine tailings, respectively. Pyrrhotite oxidation rates, as an alternative, were 2.31 + 10-12 and 1.24 + 10-11 mol m-2 s-1 in the coarse and fine tailings, respectively. Natural microbial activity was confirmed in both the tailings and the leachates; therefore, the obtained oxidation rates are not strictly abiotic. It is thus concluded, based on the experimental results, that tailing heterogeneity will result in zones with different oxidation rates, related to their physical and chemical properties.

Jan 1, 2003

By V Narayanaswamy

SustainabilityÆs imperative of economic development in tandem with social advancement and environmental protection is widely accepted, but much debate remains about the practical implications for the minerals processing technologies and practices for the future. Experience in other industry sectors however suggests that sustainability can be a value-adding framework for innovation in processing technologies, business models and management systems. This position paper explores how sustainability can drive innovation in minerals processing, by reviewing pertinent ideas and experiences gained in non-minerals sectors. Sustainable innovations can generally be broadly ranked from incremental to transformative, with each category having its own typical improvement potential, timescale and technological and operational challenges. This leads to a æmud mapÆ for sustainable innovation in minerals processing with three distinct tracks: eco-efficient operations; sustainable plant design and sustainable processing. Competing models for the sustainable innovation process through either forecasting or back-casting, have in common the strong reliance on vision, perspective and competency, which in turn highlights the importance of sustainability frameworks. Such sustainability frameworks provide normative goals and option elicitation prompts to assist with the analysis of current processes and scoping of more sustainable alternatives. A comparative analysis of five prominent environmental sustainability frameworks revealed three cross cutting sustainability themes that challenge current resource processing technologies and practices. These are: fate of materials (zero dissipation of materials); compatibility of materials and processes; and materials intensity of industrial products and processes. Although the sustainability concepts presented in this paper have not been extensively road tested in the minerals processing industry, there is ample evidence that recent initiatives in the Australian resource sector illustrate the applicability of the proposed framework. It is therefore argued that more in-depth assessment of sustainable innovation concepts would be a valuable contribution to the sustainable resource processing theory and practice.

Jan 1, 2004

The explosion of a charge in a drillhole sets the surrounding rock mass into vibrating stress wave motion. Except in the immediate vicinity of the drillhole, the dynamic stresses associated with this motion do damage only to pre-existing joints, cracks, or other weak planes, not to the rock material in between these. The joints are weak in tension, therefore the damage occurs as a result of tensile stresses. The initial damage process in the rock mass that ultimately breaks loose in front of the hole is similar to that in the remaining rock behind the drillhole. Recorded or calculated values of the vibration velocity and frequency contain a wealth of information about the combination of stress and strain that causes the damage. This paper outlines a new technique by which the peak strain energy derived from measured or calculated vibration velocity records is used to determine the local fragment size distribution. It combines two previously known and well tested techniques, namely the Holmberg-Persson calculation of the peak vibration velocity generated by an extended charge and King's calculations of the fragment size distribution as a function of the strain energy in rock crushing. Both of these calculations are based on experimental data and have been tested and found to agree well with actual conditions in their respective fields. Holmberg-Persson's calculated peak vibration velocities have been used successfully to predict and control damage to the remaining rock in cautious blasting, while King's calculation successfully describes the comminution of rock in mechanical crushing. Preliminary predictions of fragmentation in two types of rock blasting, a large hole open pit mining blast and a tunnel round, indicate that the new technique for fragmentation prediction has the potential for predicting fragment size distributions within the rock removed by the Blast.

Jan 1, 1995

This paper addresses the area of utilising automatic data capture systems in the metalliferous mining environment for the purpose of tracking personnel and vehicles, for both safety and productivity purposes.As automatic data capture systems in the form of barcodes have revolutionised the stock control procedures in retail establishments in recent years, so too will similar systems in the form of radio frequency identification products (an electronic version of the barcode) transform the way in which many aspects of mining operations will be managed.

Jan 1, 1992

Coal Mining machinery has undergone enormous changes in design and complexity of controls in the past 10 years. Specialised, high productivity equipment has been manufactured in Australia, in sufficient volume, to satisfy the local mullet needs.Local manufacturers face greater challenges from overseas competition, as well as increased customer demands to improve machine performance, productivity, quality, reliability and safety. In order to meet these demands now and in the future, it will be necessary to review work practises, and restructure production and quality systems to incorporate the latest principles and philosophies.

Jan 1, 1991