Search Documents

By Ahmed M, Leung L

A program of microseismic noise monitor ing for gas outbursts, in conjunction with other mining engineering measurements and observations, is being undertaken at Leichhardt colliery in Queensland. Headings are developed at present by shotfiring. The equipment being used in this study includes piezoelectric accelerometer assemblies to detect microseismic noise which is then transmitted to a surface base station by cable. Data are recorded on an analogue magnetic tape recorder and are also analysed on-line using a commercially-available acoustic emission pulse analyser. It is proposed to re-interpret recorded data using various modes of analysis and to interface a desktop computer to the existing system to permit continuous monitoring on the mine site. No outbursts have been recorded or analysed and only a limited number of develop- ment shots, and the resultant microseismic activity, have been recorded to date.

Jan 1, 1980

This work was instituted to investigate the microscopic structure of brown coals by means of microtome sections cut from them. It was found to be essential to impregnate the coal with some material prior to cutting, because of its powdery and crumbly nature. Of a number of impregnating materials tried, e.g., glycerine gum, gelatine, by far the most satisfactory was paraffin wax. Samples of brown coals for section cutting must be moist. When obtained, they should be put immediately into air-tight tins, and, if they are not to be used for some time, it is desirable to keep them under water containing a small amount of formalin. If the sample is allowed to dry in air, it becomes too hard to be cut. It cannot be softened again even by prolonged soaking in water.PREPARATION OF COALSmall rectangular, blocks were cut from the sample with a chisel and a strong scalpel. The largest block prepared was 3·2 x 2·5 x 0·6 cm. The faces of the block from which sections were to be cut were approximately levelled before treatment. The block was then painted carefully on all sides with two coats of warm aqueous agar, approximately 2 %. This prevented crumbling and breakage of the block during treatment. When the agar was set, the block was placed in water, and all the air removed with a vacuum pump. The water was replaced first by alcohol, then by chloroform, by the usual step transference of a series of liquids, in each of which the block was placed for 24 hours: Ethanol %, 10, 20, 30, 50, 70, 85, 95, 100 (three changes); Ethanol-chloroform, 3: 1, 1: 1, 1 : 3, chloroform pure (three changes) '. The blocks were then embedded in paraffin of melting point 56-58°C. Fresh...

Jan 1, 1947

A nine-month investigation was conducted into the effect on coke quality and blast furnace operation of the addition of bentonite and southern coal to the northern coal fed to the coke ovens at the Newcastle steelworks.Additions of 0·3 per cent bentonite or 25 per cent southern coal to the northern coal increased the coke strength from 15-20 A.S.T.M. stability to 25-30 A.S.T.M. stability. It is likely that improved mixing and blending facilities would, in both cases, give a coke of over 30 A.S.T.M. stability.For the same coke strength, the use of 0 3 per cent imported Wyoming bentonite was considerably cheaper than the use of 25 per cent southern coal, but the use of Australian bentonite promises the same coke strength for still lower costs. Other additives such as coke breeze, charcoal, iron ore fines, and certain other finely divided materials, gave relatively minor improvements in coke quality.There appeared to be sufficient improvement in blast furnace operation and production to justify full scale addition of bentonite to improve coke quality, although other variables, particularly iron ore physical quality, overshadowed on many occasions the effect of coke quality. Further coke trials with southern or bentonite will be carried out when ore quality has been improved by the introduction of ore sintering at Newcastle.INTRODUCTIONDuring the period of operation of the Newcastle coke ovens and blast furnaces from April 1960 (when No. 3 blast furnace was blown in after rebuilding) to December 1960, a bentonite coke trial was carried out based on earlier research findings (Gregory, 1959a, 1959b; Felton and Gregory, 1960; Gregory, 1960) that as little as 0 3 per cent to 05 per cent bentonite clay added to northern N.S.W. high volatile coking coals gave a significant increase in coke strength. The bentonite coke trial was followed by trials...

Jan 1, 1962

By Walters GW

A countercurrent method of metal refining using crystallization and reflux is discussed. 4n account is given of the development of this technique for the separation of silver and bismuth from lead using bench-scale studies to the present small pilot-plant unit (around one tonne per day) in the "Commonwealth Scientific and Industrial Research Organization (CSIRO)" Division of Chemical Engineering.

Jan 1, 1975

The Manto Verde copper mine (Atacama Region, Chile) is due to go into production in 1996. It will produce 40 000 tonne/year of copper cathode by heap leaching/SX-EW. Mineralogical studies were undertaken in conjunction with the metallurgical testwork program to characterise the ore and its response to leaching by dilute sulphuric acid. The leachable copper mineralogy is dominated by the oxide copper minerals: brochantite and malachite with minor chrysocolla and atacamite. The gangue minerals include abundant orthoclase, specularite, quartz and chlorite with minor muscovite and trace smectite clay, calcite and limonite. The study showed that complete or partial decomposition of calcite, chlorite, smectite and wad consumed acid and generated solution impurities (Ca2+, Fe2+, Mg2+, A13+, K+, Si4+ and Mn4+2+ ). Although these were manageable at Manto Verde, their uncontrolled build-up could have affected the operation in several ways: the degradation of heap penneability and fonnation of crud in the SX plant from the precipitation of gypsum, goethite, colloidal silica and jarosite; and the entrainment of contaminated pregnant leach solution in the SX organic resulting in the transfer of impurities to the electrolyte and subsequent effects on cathode quality and electrowinning efficiency. In conclusion, process mineralogy played an important role in understanding and managing potential mineral-related problems in the heap leaching and SX-EW recovery of Manto Verde ore.

Jan 1, 1994

By Littlewood E

We offer these notes as a practical contribution. All the arguments we advance have been tested by practical experience.In its preparation we realised that our subject was one of such importance and covered so wide a field that, dealt with by one of us alone, it might easily have been too much for him, so we have endeavoured, by mutual criticism and advice and a pooling of ideas, to bring forward a few points that may be of advantage to members. If any of the paper is of benefit to mining on the "Golden Mile," or elsewhere, we shall feel amply repaid for our efforts.It is obvious to all that the longer the machine is working productively per shift the greater the return, to all concerned; the machine-man himself and the company. Furthermore, if a man commences a shift with a definite objective in view; for instance, to bore and fire a specific cut, which he recognizes will give him a good financial return, then that man will exercise all his capabilities to attain that objective.In this paper we hope to demonstrate the value to the machine-man of the knowledge of the capabilities of each hole he bores, so that he will be enabled to utilize his drilling time to the greatest advantage. Also, we hope to show that such drilling time can be advantageously extended.After the war, with the influx of new men to the industry, some education on the finer points of machine work may be desirable, and any instruction in this branch must stress the realization of the value of each hole.We realise that most of those present have a sound workable knowledge of machine-mining, and we are not trying to teach anyone the fundamentals of machine work, but we would like to bring to their attentIon some of the finer points which we believe are very important.The machine-man has control of gear of a capital value of over £150, and the use or misuse of that material has a direct bearing on working costs. Therefore it is imperative that the capital outlay is gainfully employed.A "bogger" in charge of a 5/- shovel engaged unproductively is bad enough. How much worse for £150 worth of gear to be not fully productive.Figs. 1 and 2 demonstrate angles of break, and the full realization of the importance of this angle is essential to our paper. Although these Sketches are two-dimensional, we hope they will be sufficient to demonstrate our meaning. We will pass over them as briefly as possible.Fig. 1 shows three holes asked to perform an identical task.(a) 7-ft. hole bored 2 ft. into solid ground-will not come out.(b) 4-ft. hole bored 1 ft. from solid ground-will come out easily.(c) 5-ft. hole bored to solid ground-the best that can be expected under general conditions encountered.The angle of break is a right-angle, normal to direction of hole.

Jan 1, 1944

Up to 80 per cent of the copper in a bornite ore can be quickly leached with percolating acidified ferric sulphate solutions. The upper limit for rapid copper extraction is set by the conversion of bornite to slowly dissolving chalcopyrite. The dissolution occurs in two stages: a rapid linear initial stage, followed by a slow, non-linear stage. The initial step is largely controlled by the rate of oxidant supply (Fe2(S04)3); temperature is not an important variable during the initial reaction. The second leaching stage is controlled by chemical and physical factors and is temperature dependent. The initial copper leaching rates are insensitive to both the concentration of the ferrous sulphate reaction product, and the sulphuric acid concentration.

Jan 1, 1973

By Withington J. T

The four major contracts for the construction of Museum Station are: 1) Installation of Soldier Piles, 2) Structural Contract including the temporary support, 3) Architectural Finishes which include Electrical and Mechanical Services and 4) Supply and Installation of lifts and escalators. Specific areas of interest include the fabrication, installation and removal of temporary support steelwork, the monitoring of ground loading, and the interface between the structure and. the temporary support. The information collated during construction confirmed the design assumptions and criteria. No major changes'were required in the design of the construction methods. The open cut excavation and construction of this major structure in an inner city area was significant by any standard and was successfully completed with minimum disruption to the public and without damage to adjoining or surrounding property.

Jan 1, 1981

By Gross A. E, Neville P. C

Over the last decade heap leaching with a cement binder has allowed the economical leaching of low grade gold ores of less than 2 grams/tonne. Despite the continued use of cement as an agglomeration aid, numerous leaching operations continue to experience channelling and blinding problems. This paper describes the development of polymeric agglomeration aids, Extract Ore 9760 and 9960, which when used as a partial cement or lime replacement can result in a higher rate of and/or a higher total gold recovery in plant evaluations. Extract Ore in combination with cement acts to produce a stronger agglomerate which results in reduced fines migration during leaching and helps prevent blinding of the heap. Both of these changes will give a more even flow of cyanide solution throughout the heap and improve solution contact efficiency within the ore. Polymeric agglomeration aid programs are now being used by heap leaching operations in three different countries. A summary of benefits identified at some of these operations are presented in this paper.

Jan 1, 1994

By Shoobridge PH, Firkin GR

The Imperial Smelting Process blast furnace (ISF) of the Sulphide Corporation Pty Limited zinc/lead smelter at Cockle Creek, New South wales, has in recent years greatly increased its consumption of low grade feed materials, and as a consequence has experienced periods of unstable furnace operation. Routine examination of production sinter, including softening characteristics and micro- examination, showed that the problems had been caused by an increasing silica content in sinter. The silica entered a low melting point glass phase containing calcium and lead oxides. The relative volume of this phase increased until it formed a continuous matrix in the sinter structure and this made the sinter more likely to soften at lower temperatures. Premature softening caused loss of operating stability in both the shaft and hearth of the ISr. The required sinter structure for ISF smelting was found to consist of a network of intermeshing, refractory crystals which provided skeletal strength for sinter lumps even after the glass phases had begun to soften and melt. With an understanding of the importance of microstructure and softening temperature of zinc/lead sinter and the progressive identification of those factors in sinter production which affect the microstructure, a significant improvement in stability of operations has been possible.

Jan 1, 1980

By Trois P

A fully instrumented and bench-mounted diamond drilling machine, purpose designed and built, has been used for investigating the effect of aqueous solutions of various chemical compounds when used as drilling fluids. The rocks investigated were andesite, basalt and granite, the chemical compounds were alkylamines, with various hydrocarbon chain lengths, aluminium chloride and dioxane. Rotation speed seems to be one of the major factors affecting the emergence of mechanochemical effects as the results obtained with aluminium chloride clearly indicate. Penetration rate is either unaf- fected or enhanced by the presence of certain compounds, such as aluminium chloride. On the other hand, penetration rate diminishes when the drilling fluid contains dioxane and exhibits an apparently unpredictable behaviour with alkylamine solutions, although it appears that an increase in hydrocarbon chain length usually equates to an increase in penetration 1. Full Professor, Mining and Mineral Dressing Department University of Cagliari - Italy 2. Associate Professor, Mining and Mineral Ikea- sing Department University of Cagliari û Italy rate. Rock texture seems to have a pronounced effect on test repeatability. With hexadecy- lamine acetate solutions in concentrations ranging from 10-5 to 5 .10-4 molò dm 3 and 41.88 radòs-1 rotation speed, 46 % increments in penetration rate of andesite were observed, with respect to water, whereas penetration rate decreased in basalt by as much as 60¦%o when a dioxane solution was used as drilling fluid. An interpretation of the observed effects is proposed in the light of current knowledge of solid state physics and physical Chemistry.

Jan 1, 1992

By D J. D'Astoli, M D. Goodz

In 1993 a detailed review of drill sample yuuluy was rouxluard through twin and triplet drill holes using open hole, crossover suhreverse circulation (RC) and diamond drill methods. Advances in face-sampling RC methods demanded a further review of the validity and reproducibility of drill sample data. A program was undertaken to drill three RC holes using the latest technology (new face- sampling bits, dust suppressers, cyclones and compressors). Volumetric and mass studies were undertaken to review sample recoveries. Modal analyses on indicator minerals were logged to interpret the relative degree of mineralisation. Ambiguities in the results were immediately apparent and the consensus was for follow-up twin diamond holes using HQ3 coring tubes. The most mineralised RC hole was selected for the first twin diamond hole. This RC hole (MS 313) encountered one intersection of >0.47 g/t; in contrast the diamond hole (MS 342) had nine intersections at > I g/t. Results at hand show definitively that face-sampling RC drilling is not acceptable as a method of exploration for gold deposits of the Woods Point type. Furthermore it is demonstrated that RC drilling should not be used for any type of exploration of high-grade gold vein deposits related to highly fractured or porous hostrock, or areas of previous mining activity. Methods are proposed for reviewing of rates of sample recovery, distribution and cross-contamination. Comparisons also show that in limited metreage reconnaissance drill programs, diamond drilling is more similar to percussion in per metre costs, than it is credited with, and always provides more bang for the Buck.

Jan 1, 1997

By Walshe JL, Solomon M

The Emperor vein system lies on the eastern margin of the Tavua volcanic structure. This is of Miocene age and occurs in basalts(the Mba Volcanics) probably underlain at about 2 km by calcite-rich sediments (the Vatukoro Formation). The lodes are generally flatmakes, or steep fault fillings, or complex shatter zones, and consist of quartz and altered wall rock. In areas of open cavities it is possible to establish a paragenesis which involves five quartz stages and two ore mineral stages. The first ore stage contains calaverite, krennerite, sylvanite and native tellurium, the second petzite, hessite and native gold. The quartz stages are thought to have formed slowly (102 years) from boiling solutions of low salinity at temperatures varying with time from about 250¦C to 190¦C. The system was sealed, the temperature gradient near vertical and the mass flux small. The ore mineral stages probably formed relatively rapidly (101years) from boiling solutions at 250¦ to 200¦C when the system was mainly open. Gold deposition was probably largely a result of fall in aH2S due to boiling, the calculated solution concentration falling from a maximum of about 8 ppb at 250¦C to about 8.10-3ppb at 200¦C. Boiling is also probably responsible for an increase in a02 (by loss of H2) and fall in aTe2 (by loss of H2Te). The fluids are thought to have had a large component of meteoric water and to have been heated by plutons in the core of the volcanic structure. Stable isotope data indicate that they derived their carbon from the underlying Vatukoro Formation and their sulphur from sediments. Circulation may have been confined to the outside of the volcanic structure because of the relatively low permeability of the flows, pyroclastics and dykes within it.

Jan 1, 1987

MERLIN, the Queensland Department of Minerals and Energy's corporate geographic information system, provides ready access to all georeferenced data held by the department. Its aim is to provide a consistent, current, statewide coverage of timely information to assist in tenures management, exploration targeting and competing land use decision-making. Initially developed in 1988 and under continual enhancement since then, its functionality is the result of on-going close consultation with a wide range of departmental clients and potential users. A true geographic information system, MERLIN maintains both graphical data with linked textual information on a wide range of features of interest. The proprietary software products Arclnfo and Oracle are used to hold the graphics and attribute information respectively. Access to information is provided by a specially designed graphical user interface programed in-house. Hardcopy output of graphics displays including related attribute data as well as detailed reports of textual information can be retrieved at any departmental office. MERLIN is a network of computer systems which link each of the Department's regional offices and head office in Brisbane. The current state of exploration and mining is maintained by departmental officers processing tenure applications, transactions and dealings directly into the system. Data entered at regional offices are transferred overnight to head office to up-date central records and maintain a currency of data statewide as at the close of business the previous day. Through MERLIN the Department of Minerals and Energy now offers a much streamlined tenures management service as well as access to information about past exploration and mining, Queensland's mineral and energy occurrences and resources, and up-to-date information on the state's geology including maps, boreholes, geophysical surveys and field observations. In the future, this Geographic Information system will be invaluable to the mining industry in the development of mining projects.

Jan 1, 1995

The design of a sand pump is similar in principle to that of a water pump but differs in several areas. Results of experiments on sand pump performance have been summarized and values of design parameters quoted for optimum results. Typical performance data are also Included.

Jan 1, 1973

Supercritical fluids are gases compressed to near liquid densities and, as such, have unique properties compared to liquids: low viscosity; zero latent heat; high diffusivity and pressure-dependent, solvation characteristics. These properties are being utilised in new processes and current research is delineating areas where such processes may be applicable to extractive metallurgy. The processes and areas of interest are as follows: Supercritical Fluid Extraction in which substrates are dissolved at high pressure and fractionated at successively lower pressures. Areas of interest include extraction of organic materials for regeneration of activated carbon for the CIP process and for upgrading alumina industry products and, separation of transition metal chlorides. ò Supercritical Water Oxidation in which high pressure gaseous water acts as a medium in which substrates are oxidised while suspended or dissolved. This process may be of use for oxidation of organics in Bayer liquor and oxidation of mine waters etc. ò Supercritical Fluid Reactions where reactions occur in a supercritical fluid medium, particularly when the medium itself is a reactant. This may be of use in treating refractory or carbon-aqueous auriferous ores and in lower-temperature chlorination of transition metal oxides. Research is described which is aimed at chlorination and separation of transition metal oxides by two supercritical operations.

Jan 1, 1991

The selection of an appropriate mining method should take into account the geometry of the deposit and its physical properties. Other factors which assist in the determination are the requirements for flexibility in the mining process, minimisation of risk factors and maximising the financial return. Several established mining methods exist which can encompass the requirements to deliver the optimum mining method, this can be in both an underground or open cut environment. The objective is to outline these methods and where they can be applied in a mining project.

Jan 1, 1997

By Campbell Brown G A

IN 1904-5 diamond drilling operations in the Mount Morgan mine proved the presence of some millions of tons of rich copper-gold ore, averaging about 45%to 50%silica and 22%Fe as sulphide. To smelt this ore in blast furnaces, without previous concentration, large quantities of basic flux were required. Unlimited quantities of cheap limestone were available at Marmor, on the GladstoneRockhampton railway, 50 miles from Mount Morgan, but the supply of iron flux was a more difficult problem. Smelting Operations started with one furnace in January, 1906, using as flux low-grade sulphide ore from the mine, containing very little silica. When the second furnace was blown in this was supplemented by ironstone from small deposits in the immediate district. It was recognized that these sources of supply would be insufficient to keep the full plant going after the third furnace had been blown in. Accordingly, the deposits at Kabra and Mount Etna were opened, neither of which proved capable of supplying the quantity required-viz., 1000 tons per week. Negotiations were meanwhile being conducted with the Marble Island Iron and Limestone Co. to obtain the right to mine at Iron Island, where a sufficiently large deposit was known to exist. Shipments from this source commenced in January, 1907, and ceased at the end of July of this year, when the metallic flux from...

Jan 1, 1911

To reflect on the early history of mining in South Australia requires considerable imagination and rashness. The people who were the chief actors in the scene have long since passed away. Accounts of their activities are hazy and debatable. A broad brush account is all that I can hope to accomplish under these circumstances. It is fitting that a picture be painted and possible lessons learnt from the achievements of our pre- Decessors.

Jan 1, 1987

By Otuonye F

An outburst is the spontaneous ejection of pulverized coal and gas from the working face in an underground mine. It is caused by overstressing the rock, due predominantly to the influence of geological structures on in situ stresses, stress concentration from the excavation and overburden load on mine openings, and large volumes of gas sorbed in the rock. The spontaneous release of high pressure gas creates intense shock waves which may cause damage to the mine ven- tilation system and the pulverized rock/coal ejected may cause injury or death to miners. The gases emitted pollute the mine air and may also result in death to miners.

Jan 1, 1988