Search Documents

By S L. Barbour

Measurement of the net percolation from the base of a cover system into the underlying waste material is a key component of a cover system monitoring program. The units of measure (ie a percentage of precipitation or rainfall) are simple to understand for all stakeholders, which increases the importance of obtaining representative net percolation values. In general, lysimeters are used to measure net percolation across the cover material-waste material interface; however, the design of lysimeters for cover system monitoring programs in the mining industry have typically not considered fundamental aspects of lysimeter design. Lysimeter design is typically thought of as being conceptually simple, when in reality the design, installation, and operation of lysimeters is often counter-intuitive, due to the complexities of flow through unsaturated soil systems. This paper puts forward a methodology for lysimeter design while also presenting the fundamental design variables that should be considered. Lysimeter design for differing climates, cover materials, and waste materials is discussed. Finally, the performance of lysimeter designs previously installed in the field at sites in Australia, Canada, and the United States are subjected to numerical modelling to determine whether net percolation is being measured properly.

Jan 1, 2003

By A Winchester, D Grant

The massive 1100 Orebody in Mount IsaÆs X41 Copper Mine has been extracted over the last 40 years form north to south utilising sublevel open stoping methods.De velopment has continually stepped ahead of production to provide access to new primary stoping blocks. The remaining secondary pillars contain stopes with one, two or three fill mass exposures and were constrained by access requirements and stope extraction turnaround time.The remaining southern mining areas consist of large 40 m wide by 300 to 400 m long east-west transverse pillars that have been left to provide access for ventilation and service requirements. Three large transverse cross-cuts or transverse pillars û 4180 x/c, 4010 x/c and the Panel pillar now remain. The 4180 x/c was the last major transverse pillar to be successfully broken.This transverse pillar is being extracted in a retreating sequence, creating 3SLOS stopes due to the surrounding backfilled stopes.In recent years the extraction of the first, and most critical, stopes in the transverse pillars have resulted in large changes to the induced stress field. This paper describes the extraction of the 1.1 million tonne stope P418 in the 4180 x/c pillar.T echnical challenges that were faced and how they were overcome to allow for the successful extraction of the stope are described.Critical to the success of the P418 stope extraction were the rehabilitation methodology used; extraction strategy modifications to address deteriorating ground; mass firings with multiple directional changes; managing the exposure of backfill of variable strengths; and geotechnical monitoring prior to, during and after extraction.

Jan 1, 2005

By R C. Cox

The Brukunga pyrite mine was operated from 1955 to 1972 to supply feedstock for sulfuric acid production in the South Australian fertilizer industry. Iron sulfide ore, mined by Nairne Pyrite Ltd, was finely crushed and concentrated onsite with the concentrates being sent by road and rail to Port Adelaide for roasting. Waste rock was dumped at two locations on the western side of Dawesley Creek and the tailings pumped to a valley-fill storage facility on the eastern side. Production of 1.5 Mt concentrate resulted in 3.5 Mt tailings and 8 Mt waste rock. The site has been administered by the South Australian Government since August 1977 and a lime treatment plant has been operated on the site since September 1980. Environmental issues arising from these operations included: diversion of Dawesley Creek to accommodate the waste rock dumps; dumping of low-grade sulfidic ore in waste rock dumps at the angle of repose immediately adjacent to Dawesley Creek; exposed fresh sulfide mineralisation in the quarry floor; tailings storage facility dam wall constructed by upstream up-lift using tailings and waste rock; an acid water pond sited on the tailings; and pollution of natural drainage. As a result, the minesite rapidly became a source of acid drainage and potential contaminants (sulfate, Al, Fe, Mn, Cd, Zn, and Ni). Various Government bodies have been responsible for considerable effort and expenditure in reducing the flow of acid seepage and contaminants into Dawesley Creek. Presently an estimated 60 per cent of seepage from the waste rock dumps, tailings storage facility and quarry is collected and neutralised prior to discharge into the creek. Tailings have been covered with waste rock, biosolids, neutralisation sludge and soil and planted with grasses, shrubs and trees to reduce rainfall infiltration. Monitoring of water flows, water quality and riparian ecosystems is on-going. Consultants have been engaged to develop cost-effective remediation techniques and a five-member Brukunga Mine Site Remediation Board was appointed to oversee remediation of the site and liaise with the community. Construction has commenced on the diversion of Dawesley Creek, and plans are being developed for the relocation of waste rock back to the quarry benches and upgrading of the neutralisation plant. The paper examines operations, environmental monitoring, remediation, research and community involvement with respect to current best practice.

Jan 1, 2003

By R N. Lamb, A N. Buckley

Experiments have been carried out to establish whether time-of-flight secondary ion mass spectrometry (ToF-SIMS) is able to differentiate monolayer and multilayer coverage of thiol collectors on sulfide minerals. The systems investigated were those for which x-ray photoelectron spectroscopy is able to provide an independent determination of the extent of coverage, and included diethyldithiophosphate (DTP) and 2-mercaptobenzothiazole (MBT) on chalcocite, DTP on Ag2+MS prepared by sulfidising metallic silver, and isobutyl xanthate (BX) and MBT on galena. For monolayer adsorption of MBT on chalcocite, peaks from MBTû but not Cu(MBT)û ions were evident. For multilayer coverage, Cu(MBT)2û ions were clearly present, notwithstanding the fact that other data had identified the principal multilayer species as Cu(MBT). For adsorbed DTP on copper and silver sulfides, DTPû and metal(DTP)Hû peaks were observed for monolayer and multilayer coverage. Although the multilayer species was expected to be predominantly metal(DTP), metal(DTP)2û ions were evident for multilayer (but not monolayer) coverage. For the PbS/BX system, intact Pb(BX)2 or Pb(OH)BX ions were not detected for multilayer coverage, although Pb-containing ions heavier than PbBX were. Indeed, for all the systems studied, ToF-SIMS was able to differentiate monolayer from multilayer coverage. In general, however, the SIMS evidence alone might not be sufficiently definitive to effect the differentiation. In the case of collector adsorption on copper and silver sulfides, if the multilayer species detected had been the metal monothiolate only, and had not involved the formation of some metal dithiolate, then ToF-SIMS might not have been able to provide an unequivocal differentiation of the two coverage conditions.

Jan 1, 2005

By M Henderson, M Hudyma

Mining-induced seismicity at Junction Gold Mine became a serious operational problem in the late-1990s. Assessing the local seismic hazard is an important step in assessing the risk associated with potential rockbursting. This paper discusses the qualitative and quantitative means of assessing seismic hazard used at Junction. In qualitative hazard assessment, the role of the primary factors contributing to mining-induced seismicity and rockbursting are identified. These factors include: rock mass properties, geological structures, mine development, and stoping. A qualitative seismic hazard map has been developed considering these factors. In quantitative hazard assessment, seismic source parameters from an Integrated Seismic System are used to assess seismic hazard. The seismic source parameters found to be relevant to seismic hazard assessment at Junction are discussed.

Jan 1, 2002

By M I. Pownceby, S Hapugoda, H Han, E Donskoi, L Lu

Iron ore sinter mineralogy and its associated macro-/micro – structure has a strong impact on sinter quality. At a macroscopic scale, sinter ideally consists of a strong, porous matrix which bonds relict ore nuclei together. Microscopically, the sinter matrix (solidified from the melt part of the initial sinter mix) generally consists of complex calcium ferrites known as SFCA, secondary magnetite and hematite grains (precipitated from the primary sinter melt), glass and silicates. Depending on the conditions under which the sinter structure is formed, two major forms of SFCA with different morphologies are generally recognised, ie fine micro-platy SFCA (usually termed SFCA-I) and coarse columnar/prismatic SFCA. Detailed optical microscope observations of several pot grate and compact sinter samples revealed the presence of a variety of fine, coarse and dense forms of both types of SFCA. The controlled cooling tests revealed that cooling rate has an impact on the form and size of SFCA crystals. In this work, EPMA analysis of SFCA compositions from a variety of pot grate and compact sinter samples are presented. Results show that the SFCA types exhibit a broad range of complex compositions within the system Fe2O3/CaO/SiO2/Al2O3/MgO/TiO2/MnO2. Although SFCA-I and SFCA are known to be crystallographically distinct and with different, well-defined ranges in composition, there was considerable overlap in compositions of the experimental sinter samples. The development of SFCA textures depend on several parameters including the local chemistry and conditions including the maximum temperature attained and the cooling rate, within the sinter bed, thereby suggesting that SFCA identification based on morphology alone may be erroneous.

Nov 8, 2021

Upon subduction, water is liberated from the sediments and the porous struc- ture of the oceanic crust and from de- hydration of minerals for redistribution and chemical reaction. A survey of pro- cesses which are likely to occur along the subducting plate reveals that water may well be basic in subduction induced gas generation, magma formation and ore deposition. In analogy to the industrial water gas process, reaction of water with car- bonaceous matter, in subducted sediments is likely to yield substantial volumes of hydrogen and carbon dioxide. While water and carbon dioxide appear to play a determining role in the development of differentiated magmas, hydrogen will react with metal sulfides and sulfur to form hydrogen sulfide which is essential in sulfide ore depo- sition. A survey of possible metal extrac- tion chemistry along subduction suggests a stepwise solubilization of metals from sediments and oceanic crust, and a poten tial accumulation of dissolved metals in zones of characteristic composition. The metal spectrum in ore deposits at near surface appears to reflect the com- position of the solution in the respec- tive subduction zone. A tendency for preferential solubi- lization of copper at subductidn level, from among the transition metals, an in- creasing generation of hydrogen sulfide in the sane direction and partition effects as well as sulfide precipitation characteristics lead to enrichment in copper and to its selective deposition in the direction towards the trench as observed in S. Latin America. A postscript deals with the formation of native copper.

Jan 1, 1986

By A C. Edwards

The Mesozoides of North-Eastern Asia represent a collage of exotic terranes which were accreted to the margins of the Siberian continent. In the Late Precambrian and Phanerozoic, the passive margin of the Siberian continent (the current north-east) broke up into a number of discrete fragments as a result of rifting events in the Riphean, Early and Middle Paleozoic. Rift related mineralisation includes stratiform and stratabound copper and base metal mineralisation in the structures of the Omulevka, Okhotsk and Prikolyma basement terranes, as well as along the edge of the Siberian continent in the Paleozoic sediments of the Verkhoyansk passive margin. During the Late Mesozoic the terranes were reassembled in a series of accretionary events. At the end of the Jurassic, the velocity of the Kula plate increased, and the opening of the Canadian Basin in the Arctic commenced, changing the vectors along which the Siberian and North American plates moved. Island arcs terranes were pushed back onto the Omolon super-terrane which was in turn pushed onto the Siberian Craton in a series of massive collisional events that resulted in the restructuring of the whole region. Numerous granitoids characterised by collisional and island arc chemistries with Au and accompanying Sn, and W mineralisation were emplaced. Mesothermal gold-quartz mineralisation was emplaced in a series of narrow belts that adjoin major crustal sutures and that spatially overlap belts of granitoids and zones of subgreenschist metamorphism. Each of these gold-quartz vein belts corresponds with a specific collisional phase. In the middle Cretaceous, the Okhotsk-Chukotka volcanic belt developed along the paleo-Pacific margin of the Siberian continent. Epithermal Au-Ag developed in the volcanics and shallow mesothermal Au-Ag-quartz and Au-Sb mineralisation developed in the Mesozoides. Porphyry and skarn style mineralisation developed in both the island arcs and in the continental Okhotsk-Chukotka Volcanic Belt.

Jan 1, 1999

By Carlini G, Ibba R

The KSS Lead Plant (Kivcet - SNAMPROGETTI - SAMIM) of Por tovesme, owned by Nuova Samim (the sector-head Company for non ferrous metals and derivatives owned by ENI), has been operating since february 1987. This plant is based on the Soviet Kivcet licence and testwork carried out on the pilot plant of VNIITSVETMET in Ust Kameno gorsk fed by the Nuova Samim's concentrates. The plant is com pletely automatized using the most advanced technologies and it is operated by nineteen people on shift work, including all ancillary units and lead decopperizing-casting. The expected performance of the plant has been confirmed and improves day by day in relation of the operating experience, thanks to the new conceptual design of the furnace. Due to the remarkable flexi bility of the process, the integration of the lead plant with the other plants of the metallurgical complex of Portovesme rro-#4 (Electrolytic Zinc Plant, Sulphuric Acid Plant, Imperial Smel ting) has shown all the economic advantages. The lead content in the ambient air, detected by the monitors, either in the working area and on the ground outside the complex, is widely Pb W" below the stricter new limits recommanded by the E.E.C. (Economic European Community) rules and by the Italian law. The whole process is carried out in equipment completely closed and under suction and it does not require manual operations with exposure to the lead. The production cost is much lower than that performed by the traditional technology. This advantage permits wide margin to consider investment to replace the traditional technology.

Jan 1, 1989

By Girnau G

The necessity of effective dust suppression measures during excavation work is just as uncontroversial in tunnelling as it is in mining. In many respects, in fact, the applied technology is comparable. Notwith- standing, given more careful appraisal, it becomes evident that very different starting conditions exist in both these fields: In mining, there are for instance, well organised firms, which in many cases have been active for several decades, carrying out the required drivage and winning operations - and although there are also experienced firms in tunnelling, these generally speaking form a joint venture in order to accomplish a certain project. These "tunnelling firms" which are formed for a short term, normally only exist for a period of two-to three years. They con- stantly reorganise themselves: from the site supervising engineers by way of the foremen and shift overseers to the gangs working on site. The "firm's headquarters" are also re- located when a new project is started up. Then of course, there is often pronounced fluctua- tion among the crews of a single tunnelling project. Seen from this point of view, a safety expert in tunnelling has a far more difficult task than one in mining. He has not the advantage of knowing every corner of the mine for years if not decades on end, of being familiar with the overall organisation of the enterprise let alone knowing many of the men at the face. This ideal prerequisite for effec- tive decisions pertaining to suitable measures for industrial safety and accident prevention taking all weaknesses into consideration given the interplay of the most varied system com- ponents, can practically only be arrived at in mining.

Jan 1, 1987

A new lead refinery with a. capacity of 230,000 tons per year com-menced operation at*Port'Plsie in October, 1959. This plant' superseded the refinery which had operated from 1933 with the advent of thecontinuous lead refining process. The incorporation of new equipment following local metallurgical developments, together with the overseas demand for lead of extremely low antimony content, created difficulties in operating the original plant. The new refinery project was under-taken to cover this disability and to gain the full advantage of the new processes.Desilverising and softening are carried out in units identical in size to those used previously. Metallic'zinc is now recovered from the entire output of desilverised bullion by vacuum distillation. Final refining is then carried out by batch'treatinent with caustic soda yield-ing lead of purity previously unattainable at Port Pirie.These two processes have replaced continuous dezincing by oxidation, a high temperature process which caused large quantities of lead and antimony to be recirculated. As the final stage is a .batch process the product composition can be.checked before casting. Individual batches can be adjusted to produce special alloys to,consumer's specification.Improved casting equipment has allowed the quantity production of pigs of good physical characteristics either as 56 lb bars or 2000 lb pigs. This, together with the high purity of the lead, has assured the B.H.A.S. position in world markets.Automatic control systems have been extensively employed particularly on the vacuum dezincing unit.The anticipated financial benefits have been achieved mainly by a reduction in the tonnage of recirculated materials, a smaller labour force, and reduced maintenance requirements.

Jan 1, 1963

By A D. T Goode

Data Metallogenica (DM) is unique as a global mineral sample collection and deposit database with over 70 000 rock samples and a wide range of descriptive, photographic and measurement data. Subscribers have access to approximately four gigabytes of on-line data with many examples included on the public pages. DM commenced its life on the Pacific rim in 1971 and much recent growth has focused on countries of the Pacific margin, particularly Australia, Fiji, Chile, Indonesia and Peru. Approximately 600 separate deposits and mineral occurrences in this region are represented in DM. The sets of rock samples have been photographed at high resolution and included on the web site, together with unpublished descriptions, deposit cross-sections, bibliographies, field and mine photographs, petrology and reflectance mineralogy. Figures and abstracts from PhD theses are a new addition and the donation of proprietary databases by companies and individuals is an encouraging trend. DM increasingly is being viewed as an acceptable and important repository for æfragileÆ and irreplaceable personal and company data, it is also being recognised in its true light as a high level information system, not solely a collection of rock samples. Data Metallogenica is a not-for-profit venture of AMIRA International that requires self-funding from December 2004. Growth and development must be funded entirely out of subscription and sponsorship revenues because no government subsidy is provided. The Pacific rim is in the mainstream of mining and exploration activities worldwide and those involved have much to gain from a dynamically sustaining DM. The home page at www.datametallogenica.com contains much example data and details of subscription and membership rates.

Jan 1, 2004

By T Sirinawin, R H. Murfitt, W Shywolup

The Bong Mieu Project lies within the Pre-Palaeozoic Kontum Craton near the southern margin of the regional Phuoc Son û Tam Ky Suture. The Suture and accompanying Truongson Fold Belt of Indosinian age host significant gold and base-metal bearing districts including OlympusÆ other project at Phuoc Son to the west of Bong Mieu and OxianaÆs Sepon project in Laos. The Bong Mieu Project is located some 90 km south of Da Nang and some 30 km south-west of Tam Ky, the provincial capital of Quang Nam province in central Vietnam. The project area is covered by an Investment Licence of some 30 km2 which was granted in 1991 and a mining permit of some 365 ha granted in 1992. Several mesothermal, gold-silver deposits with assigned resources are present on the property. Deposits with assigned resources contain some 615 000 ounces of gold in situ. These are at Ho Gan and Ho Ray which are potentially exploitable by open-pit mining and Nui Kem which is potentially exploitable by underground mining. Newly discovered extensions to the known deposits at Ho Gan, Ho Ray and Nui Kem, and several other new prospects, are currently being investigated by drilling. The Ho Gan mineralisation is of mesothermal, shear and shear breccia quartz vein, as well as intrusive breccia hosted style. Nui Kem mineralisation is of mesothermal, shear and shear breccia quartz vein style. The Ho Ray mineralisation is of skarn (gold-bismuth-tungsten) and lesser quartz vein style. The deposits straddle and flank the east-west trending Bong Mieu Anticline which trends through the central portion of the Investment Licence. In this paper the geology of the deposits, details of resources, results of recent exploration on the Investment Licence and recent engineering and mining studies at Ho Gan are briefly reviewed.

Jan 1, 2004

By Dawson CF

About 17% of the world's present day oil supplies comes from wells drilled in the continental shelf of some 28 countries. The demand for oil is increasing each year and is expected to quintuple in the next decade. In the same period, the demand for gas will climb to at least 20 times its present rate. In the next decade, the percentage of oil and gas obtained from offshore is expected to rise to nearly half the world's consumption. The offshore oil industry is currently striving to achieve new technological advances in the field of deep ocean operations, especially in face of adverse seas. While the emphasis was put on drilling vessels for exploration, the industry was slow in developing effective offshore construction vessels. Until a year ago, construction vessels were but large barges with construction equipment mounted on their decks. These vessels all shared the same severe limitation: When the sea exceeds a five-foot wave height (and in some cases as little as three feet) the conventional construction barge is forced to suspend operations. In face of an oncoming storm they must run for shelter. Their utilization, therefore, is limited and in rough weather areas, such as the North Sea or the Bass Strait is lower than 50%.

Jan 1, 1970

By L Neindorf

The development and application of paste fill, cement slurry aggregate fill and shotcrete bulkheads at Mount Isa Mines is described. The progressive changes in filling style in the Mount Isa copper mines from a dry fill based cemented rock fill to tailings based paste fill and slurry fills is explained. The development of shotcrete arched bulkheads and engineered drainage system is described. Details on how Mount Isa Mines has achieved approximately 30 per cent cost reduction in backfill operations through innovations are given. The development of a rocky paste fill is explained.

Jan 1, 2005

By Kandemir H, Stafford G

The Croydon Gold Mine is located in northwest Queensland and is a joint venture between Central Coast Exploration N.L. and Pancontinental Mining Ltd. The mining operation commenced in 1987 and consists of satellite open pit mines feeding a central Carbon-In-Pulp gold Treatment Plant. The gold mineralisation is hosted by quartz veins within the Croydon Volcanic Group and the Esmeralda Granite, a cogenetic igneous suite of Middle Proterozoic age. The mineralisation comprises gold and silver with associated basemetals. The gold and silver electrum occurs as extremely fine free grains. The gold distribution is heterogenous occuring across the full vein width, or restricted to the footwall or hangingwall. The average mineral resource grade is 3.5 g/t. The deposits are all hard rock and mining is carried out by drill and blast technique. All mining activity is carried out by a mining contractor. Mining is by a selective mining method which entails the drilling, blasting and extraction of the hangingwall waste prior to orebody extraction.

Jan 1, 1989

Financial markets are subject to constant change and project finance, as a product within these markets, adapts and will continue to adapt with those changes. A meaningful discussion of these adaptations requires an understanding of differences between non-, limited and full recourse project finance. The reasons sponsors seek and lenders provide project finance are also pertinent in this context. Arranging a project, financing package can be a canplex and time consuming task. An important first step is choosing the right advisor for the assignment and then structuring and tailoring the financing before approaching prospective lenders. The last thirty years has seen changes in the needs of sponsors and the ability of lenders to meet them. These shifts in preference may well be a guide to the future. Several major project financings successfully canpleted in Australia in the last few years and more recent examples are broadly discussed. Project finance will be keenly sought in the future and the form and nature it takes will continue to vary.

Jan 1, 1983

The Australian Mineral Industry's growth in the last two decades is directly related to the skill and experience of its consultants in mining, metallurgy, geology, finance, management, marketing, and engineering. The role of mining consultants needs to be re-examined, so that the quality of the service they deliver will continue to be adequate for the 1990's. One means of this evaluation is by examining Case Studies in the strategies and difficulties of developing contract and entrepreneurial research.

Jan 1, 1986

The efficient design of carbon-in-pulp (C.I.P.) plants involves the integration of both process engineering and design engineering.Many recently constructed plants have not recognised the above interrelationship, and as such have incurred higher capital and operating costs than were in reality necessary. This has been compounded in some cases by slavishly following the design of plants where process conditions are different for the ore characteristics in question, thus perpetuating design errors that finally become industry "accepted practice".In the paper that is to be presented the unit operations of crushing, grinding, classification, leaching, adsorption, desorption and electrowinning in C.I.P. plants will be discussed with reference to the integration of process and design engineering.

Jan 1, 1986

By Smith J. W, Hart G. N

Compositional and isotopic analyses of coal seam gases in the Southern Coalfields have shown that these gases frequently contain abnormally high concentrations of magmatically derived carbon dioxide. The size of this carbon dioxide reservoir and the extent of permeation of the sediments by carbon dioxide are not known.Therefore caution in evaluating the natural gas potential of the region is advised.

Jan 1, 1981