Search Documents

By D Davis

The prediction of ground-borne noise levels from tunnel construction activities requires knowledge of the input vibration forces from the vibration source(s) into the cutting face, knowledge of the vibration transmissibility through the surrounding medium, and knowledge of the receiver building’s vibro-acoustic response. The conversion of this vibration energy into sound pressure within the receiver building depends upon the vibration coupling of the soil and the building’s foundations, the structure’s response including floor-to-floor attenuation and amplifi cation due to resonance, the radiation effi ciencies of the internal structural elements, and the room’s acoustical properties. Beginning with a known input vibration spectrum at the cutting face, it is possible to predict the resultant ground-borne noise levels within a receiver building using either analytical and/or empirical techniques, or by numerical modelling. This paper presents an overview of the various methods available to estimate ground-borne noise levels from tunnel construction activities and discusses the advantages and limitations of each.

Mar 8, 2011

By P Gehrke, S O’Gorman

The precise measurement of NO2 was historically difficult in road tunnels, hence criteria and design analysis was based on converting from NOx concentrations via a set NO2:NOx ratio. The reliable direct measurement of NO2 is now possible, however design analysis is still dominated by emissions tables and formulas specified in terms of NOx. For converting from NOx to NO2 in a road tunnel environment in Australia, the ratio has typically been assumed to be ten?per?cent. This has generally been based on the recommendation in PIARC (2000) and on the ‘average’ value cited in PIARC (1995).Determining this ratio is important as changes in engine technology and in-tunnel pollution criteria along with improvements in CO and particulate emissions control, may mean that NO2 will become the driving factor for future ventilation requirements. Correct selection of this ratio can directly impact the ventilation capacity and system design.Recent research has indicated that choosing a constant ratio of ten?per?cent for all tunnels may not be appropriate. The in-tunnel ratio has been estimated to be as much as 20?per?cent to 30?per?cent and depends on the location in the tunnel, the type of ventilation system and the traffic/fleet characteristics. This paper discusses the effect of some of these parameters on the NO2:NOx ratio in road tunnels.The findings indicate that the ten?per?cent upper limit on the NO2:NOx ratio in PIARC (2000) may be a conservative value for design purposes for longitudinally ventilated road tunnels of typical length in Australia. A value of seven?per?cent to eight?per?cent may be more appropriate in some circumstances. However, the value chosen will depend on the specific tunnel in question and the confidence in traffic conditions expected. Values above ten?per?cent may be encountered for short periods but usually when the NO2 levels are low.CITATION:O’Gorman, S and Gehrke, P, 2014. NO2:NOx ratios in Australian road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 95–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M R. Asef

Although generation of environmentally harmful hydrogen sulfide is considered to be related to sour gas fields, sweet gas reservoirs and waste fluids, travertine springs and geothermal fields may also produce acid gas (H2S and CO2) under certain conditions. The potential parameters influencing such a possibility need to be fully investigated to evaluate the extent of the consequences and predict hydrogen sulfide generation accordingly. Reports on hydrogen sulfide production at different regions and fields were gathered worldwide for the cases when some of them did not have such a problem previously. In order to inspect different aspects of these case studies, some other regions with no hydrogen sulfide content were selected as control. In all cases water samples were taken carefully for chemical analysis in the laboratory. Besides, mineral compositions were characterised in some cases for better evaluation. In order to give a thorough prospect of hydrogen sulfide production, a geochemical model was prepared. In situ engineering geological conditions, especially pressure and temperature, were assigned in the model to investigate the possibility of H2S generation using PHREEQC software. The results of modelling revealed that although many similarities existed between mineral compositions of the cases, certain formations were particularly prone to hydrogen sulfide generation. For better evaluation, important exchangeable cation ratios such as potassium/sodium, calcium/magnesium and ion proportions like sulfate and chloride were calculated as trends of the formations. As expected, the model could successfully monitor a higher ratio of SO42- and Cl- in potential H2S generator formations. Wide variation in percentage of HCO3- was considered as a secondary observatory parameter for better estimation. In addition, it was noticed that higher anion content created an environment ready to absorb any cations and this makes H2S generation easier. Finally, using correlations between predictors and estimators for low depth and deep samples defined the degree of effectiveness for every sample.

Sep 26, 2011

By R K. A Taylor

The growth in production of beneficiated ilmenite products has been one of the most significant trends in the titanium feedstock industry over the past 30 years. In this period, the production of titanium slag and synthetic rutile has grown five-fold to the point where these products represented 56 per cent of total feedstock production in 2000. Additional production capacity is being proposed as the core component of new feedstock supply projects presently under consideration. A high proportion of these products is based on technologies for which the inherent quality of the is an essential factor. Location specific factors also play a large part in determining the cost of production. As the demand for such products grows, and the availability of favourably located sources of ilmenite of suitable quality declines, it can be expected that existing beneficiation technologies will become increasingly constrained. Existing beneficiation technologies, and those which have been developed, but are not yet commercially applied, are reviewed. Future issues which are likely to impact on the cost effectiveness of these technologies, or the quality of final products, are identified. These factors suggest directions for development of ilmenite beneficiation technologies to achieve economic production of the quality of feedstocks which will be demanded by the TiO2 pigment industry in the future.

Jan 1, 2001

By MáAndrusiewicz, M M. Hilden, M S. Powell, P D. Kay, B Foggiatto

Circuits with unconventional and potentially more complex designs are predicted to become more common in the future as plant designers and operators look to process ores more efficiently. Ideas have been presented on how circuit design may be changed to utilise todayÆs technology to address tomorrowÆs challenges (Powell and Bye, 2009; Powell, Benzer and Mainza, 2011a). High pressure grinding roll (HPGR) installations in various configurations; application of preconcentration plants eg sorting, magnetic or gravity separation; and preweakening devices eg microwave processing; are all examples of technologies having the potential to deliver a significant reduction in comminution energy for ores amenable to these processes. Not only will future novel circuits contain equipment for which models are not as well developed (if at all), many will likely require the ability to respond to variations in feed, and interact with geometallurgical models requiring process adjustments when the ore characteristics change.In order to confidently simulate more complex circuits and accommodate variations in feed type, a significant advancement in modelling and simulation capability is required. This includes dealing with multiple components in the feed, accommodating different competencies of ore, utilising physical separation opportunities and tracking the grade reporting along the different potential processing routes. Developing the means to simulate complex circuits has been a key priority of a collaborative group of comminution researchers working to solve these challenges.Simulations are presented utilising a new configurable simulation interface called the model developers kit (MDK). The MDK is designed to accommodate multi-components and incorporate new models under development. These will be used to demonstrate the potential of flexible circuit design, based on measured ore properties and equipment performance.CITATION:Foggiatto, B, Hilden, M M, Powell, M S, Kay, P D and Andrusiewicz, M, 2012. Simulation of flexible circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 291-298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A Galli

Traditionally pit optimisation and scheduling is carried out assuming that the resources, the commodity prices and production costs are all known. Once the pit contour and the mining schedule have been determined, geostatistical simulations can be used to assess the impact of the uncertainty in the resources on the pit design and the schedule, and likewise stochastic simulations can be used to test its robustness to fluctuations in costs and prices. But it would be more interesting to have a dynamic procedure for optimising the pit as the resources become better known and as economic factors such as commodity prices and costs evolve over time. This paper presents a novel approach for doing this. Rather than working with millions of small selective mining units, it was decided to work with large blocks, called macro-blocks. Mining sequences are defined as the quantities to be extracted from each macro-block in each time period. Feasible mining sequences are mining sequences that respect the accessibility constraints, and also the geometric constraints on the amounts that can be extracted from any one block over time, or from all the active blocks at a given time. Having defined feasible mining sequences, their mathematical properties were studied. It was found that natural breakpoints occur in the sequences when one set of blocks have been completely mined out, thereby opening up access to others. It was discovered that families of sequences exist, and that they are convex and closed under certain types of row permutation operations. Convexity is an advantage when optimising. The closure property opens up the possibility of mixing and matching subsequences of rows in the sequences. Another interesting property is that the sequences form branching families, rather like the binomial and trinomial trees used to model prices in finance and in real options.It is easy to generate large numbers of feasible mining sequences randomly. A two-step procedure is used to find the best one (or the best few) using three economic criteria: expected NPV,the probability of a negative NPV, and the percentage of years when the cash flow is negative. The procedure was tested on a synthetic gold mine based on the characteristics of the Essakane mine in Burkina Faso. The results were encouraging.

Sep 26, 2011

By P Toor

Due to the high energy consumption of milling, it is desirable to improve the efficiency of this process. One alternative to reduce energy and material consumption while optimising production yield in mill operation is through balanced design and selection of liners. Over-design of liners leads to increased life but at a cost to grinding performance, a relationship which to date has not been studied closely. This paper provides a description of this process of liner life cycle optimization and presents initial results from the first of two life cycles being studied for a 32 foot (ft) SAG mill. The use of commercially proven high resolution laser scanning based liner shape information provided by the MillMapper® software correlated with well controlled site surveys at various points in the liner life was used as the basis for comparison. The survey data was modelled in JKSimMet to provide direct comparisons of mill performance. This potentially provides a methodology for the design of liners that maintain a favourable shape for the majority of liner life, yielding desirable production parameters such as lower specific energy consumption and higher throughput, while at the same time maintaining practical liner life cycles.

Aug 8, 2011

By C Smith, R I. Maczkowiack, P D. Erskine

Open cut coal-mining has been conducted in the Bowen Basin region of central Queensland for almost five decades, and has disturbed an estimated area of 140 000 ha of agricultural land until 2011. Approximately one-third of the area disturbed by mining has been rehabilitated to pastures or bushland. However, none of the rehabilitated land has yet been assigned a specific end-use. This research project develops an approach for assessing end-use risks for the regionÆs mined land, and develops risk assessment models for selected end-uses. First, a web-based survey of stakeholders was used to identify risks to be assessed. The risks identified were surface erosion, subsurface erosion, bushfires, weeds and feral animals. The survey also identified possible end-uses of bushland and grazing. Second, conceptual risk models were developed based on the risk assessment concepts of likelihood and consequence specified in the Australian and New Zealand risk assessment standards. Likelihood was modelled using site characteristics and management factors that influence the occurrence probability of risks (eg surface erosion), while consequence was modelled using a set of site condition indicators and condition thresholds (changes in root-zone water-holding capacity, soil erodibility, vegetation ground cover and soil organic matter and transition probability to a non-preferred ecosystem type).The factors influencing likelihood and consequence for each risk have been integrated using Bayesian networks. The next step in model development is to parameterise the Bayesian networks using existing equations, empirical datasets, or expert opinion where data are not available. The parameterised models will be used to assess grazing and bushland end-uses against erosion, bushfire, weed and feral animal risks for rehabilitated mined land sites, with the purpose of identifying the relative risks associated with each end-use, and the landform design specifications and land management practices under which end-use risks are minimised.CITATION:Maczkowiack, R I, Smith, C and Erskine, P D, 2012. Risk assessment models for post-mining land use, in Proceedings Life-of-Mine 2012, pp 33-42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By M I. Pownceby, M A. Rhamdhani, D M. Fellicia, S Palanisamy, R Z. Mukhlis

The trend of global copper production has prospectively increased over time. Based on typical mined ore grades, 1 t of copper ore generates approximately 6–10 kg of copper, which requires much energy, usually in the form of metallurgical coke. Copper production using carbon as a fuel and reductant contributes up to 0.3 per cent to global greenhouse gas (GHG) emissions. As a result, research into decarbonisation processes applicable to reducing low-grade copper sulfide ores, copper oxides, electronic wastes and other alternative complex Cu-rich materials has increased. Alternative fuels for reducing carbon-rich emissions in pyrometallurgical copper processing include methane, ammonia, biomass, solar and wind power, but in recent times increased focus has been on hydrogen as a potential fuel and reducing agent for materials such as oxidised copper scrap, Cu2O/CuO and Cu-rich slags/e-wastes. From a thermodynamic perspective, hydrogen exhibits a significantly more negative standard Gibbs free energy (ΔG°) than copper oxide making it a suitable reductant and the exothermic thermal effect from reaction between hydrogen and Cu2O/CuO may be used to control process parameters. These characteristics renders hydrogen an ideal gas for reducing copper oxides and copper-containing slags/e-wastes. This review article assesses previous research on utilising hydrogen for producing and refining copper from primary and secondary feed materials.

Jun 19, 2024

By M A. Wells

A new approach to more reliably predict the Ni (and Fe, Mg) composition of Ni laterites was tested for RC samples from the (siliceous) oxide–style, Siberia North deposit, Kalgoorlie Nickel Project (KNP), in the north-eastern Yilgarn (WA) using partial least squares regression (PLSR) analysis of diffuse reflectance spectra over the 380 - 2500 nm wavelength range with a multi–element chemistry data set. PLSR cross-validation models were developed to predict FeO, MgO and Ni contents in composite samples with bulk composition limits of >0.08 wt per cent Ni and <6 wt per cent MgO. Calibration and validation models showed a strong, linear trend for predicting FeO and, to a lesser extent, Ni content, whereas PLSR models for predicting Mg content were less reliable. This reflected the prevailing mineralogy and associated element deportment within the oxide laterite profile. For example, Fe and Ni distribution is controlled by relatively few minerals, predominantly goethite and, to a lesser extent, the Fe3+-bearing smectite, nontronite. Magnesium is associated with a range of Mg-bearing minerals, some of which are compositionally complex (eg serpentine, talc, chlorite, smectite and carbonates). Magnesium chemistry alone does not reflect the varied mineralogy of samples with relatively high (5 - 6 wt per cent) MgO contents, which can be spectrally distinct. Hence, samples with similar Mg contents, though comprising Mg-bearing minerals with distinct reflectance spectra, were difficult to model (eg smectite versus Mg-carbonates). The findings of this study demonstrate that characterisation of Ni laterite composition may be achieved as part of routine logging of either drill chips or diamond drill core using PLSR analysis, but that a detailed understanding of the mineral-element association is essential for reliable predictive analysis. This has particular relevance to characterising the geometallurgy of Ni laterites, especially where deposits may be classed as the same type, but have distinct compositional and mineralogical differences.

Sep 5, 2011

New Celebration Gold Mine is located 35 km SE of Kalgoorlie, Western Australia, in the Archaean Kalgoorlie-St Ives Greenstone belt. The leases total 119 sq kms and arepart of a joint venture between Newmont Australia Ltd (as manager) and Mt Martin Gold Mines N.L. Mining commenced in August, 1986 and is now producing over 115,000 ounces of gold per annum. A variety of gold mineralisation styles with a total resource of 23.5 million tonnes at 2.19g/t are associated with shear zones at New Celebration. Gold production is co-ordinated from 7 open pits with others planned to com- mence soon. A large scale underground trial mining operation has com- menced with a decline on the hanging wall of the main producing orebody, Hampton Boulder. Millfeed produced is classified on the stockpile according to grade and metallurgical performance and blended tomaximise throughput while main- taining grade through a CIL treatment plant currently operating at 1.7 million tonnes per year.

Jan 1, 1991

By A A. Latscha, D O’Connor

Increasing orebody complexity, restrictions in ground access, and longer lead times for disturbance approvals, have generated the need for the Resource Development Team within Rio Tinto Iron Ore (RTIO), to explore optimised drill design techniques that deliver resource conversion value while maximising program outcomes. In response to this challenge, the Team initiated a case study to produce an AI assisted/designed drill program using a non-machine learning AI. The case study involved the assessment and implementation of an AI generated drill program at one of RTIO’s Pilbara iron ore deposits, located in the Hamersley Province of Western Australia. The Mineral Resource is currently classified as 100 per cent Inferred. Access constraints inherent to topography, and the presence of exclusions zones have prevented adequate drilling coverage, resulting in lower resource confidence and a poor definition of the orebody extents and geometry. The drill campaign, planned in Q1 2023, needs to consider access constraints, complex topology and the limitations related to additional ground clearance, while addressing the requirement of improving orebody knowledge. The drill plan had to address two objectives. The first and main aim of drilling was to upgrade the Resource Classification to allow for possible conversion to Ore Reserve. The input for this objective was a volumetric representation of the areas currently not meeting pre-defined quantitative Resource Classification upgrade criteria. The second objective was to better define the orebody extents and geometry. For the second objective, the input to the drilling optimiser was a volumetric representation (blocks) of the areas of high uncertainty in the mineralisation/waste boundary, which were defined using an indicator conditional simulation technique. The drilling optimiser output was a range of compliant drill plans. A set of KPIs based on economic and orebody knowledge criteria were used to assess the plans and to select the most optimal drill design to be drilled in 2023. The geology and management teams were able to make better informed, objective decisions using the trade-off between cost and orebody knowledge gained. As part of the assessment, the AI generated plans were compared to our current planning practises. The AI assisted plans, when gauged against the project KPIs, showed clear and measurable improvements in both meeting project objectives and in managing operational risk.

May 24, 2023

By Hebbard GJ

Vertical crater retreat mining is being used at Zinc Corporation, Limited and New Broken Hill Consolidated, Limited for pillar recovery between previously mined and filled stopes. In order to increase productivity in the older lead lode areas of the mine, particularly in the lower grade sections around the keel of the orebody, score form of longhole stoping was considered necessary.Due to poor ground conditions in the country rock surrounding the ore and the requirement to provide sane wall support during mining, primary VCR mining has been utilised in these areas.At Zinc Corporation, several stopes have thus far been mined by a hybrid longhole stripping - VCR method.

Jan 1, 1985

By Bukeikhanov D. G, Syedin V. F, Sagyngaliyev K. S

The present paper describes a method of simulating deposits of com- posite structure by means of computers. The method employs mathematical tech- niques to study the openworks zone formation dynamics in open-pit mines with any mode of the works front ad- vance as well as to determine, on oriented graphs,the optimal direction of openworks expansion.

Jan 1, 1977

By H Arvidson, J Vann

When only wide-spaced drilling is available, for example at concept, prefeasibility and feasibility stages, properly implemented linear estimation (including ordinary kriging) predicts grade tonnage relationships that are over-smoothed compared to final production estimates (and production). Non-linear estimation and conditional simulation are alternative geostatistical approaches that can provide more reliable estimates of the recoverable tonnage and grade from wide-spaced drilling. Non-linear estimation and conditional simulation have been rarely used on iron ore deposits. However, these techniques have had wide application in other commodities such as gold and base metals. Conditional simulation has been used in the iron ore industry (eg Guibal et al, 1997); however, its use here is outlined as a means of generating non-linear estimates, not just its use for variability and drill spacing analysis. As a rule, regardless of commodity, the decision to use non-linear geostatistics will necessitate increased skills and require more time. This decision must therefore be justified in terms of cost-benefit. Such cost-benefit analysis is not straightforward, and to help an approach for determining when linear estimates are inadequate is presented. Recommend in this paper is a well-established non-linear geostatistical approach, the global ædiscrete Gaussian modelÆ (DGM) of change of support, as a tool to establish whether moving from linear to non-linear estimates will materially improve estimate results. Also discussed is the additional use of DGM as a block model validation tool. One specific factor contributing to the lack of application of non-linear geostatistical methods in iron is the added difficulties that arise when conditional simulation and non-linear estimates are required to reproduce the numerous and often important correlations between variables in iron ore deposits. Consequently, presented in the paper is a synoptic review of non-linear estimation and simulation methodologies applicable to correlated variables.

Jan 1, 2007

By Bearman R. A, Parkin R. M

In the comminution industry cone crushers are widely used for secondary and subsequent stages of size reduction. Traditionally cone crushers have been operated and monitored manually. Alteration of discharge setting is now commonly achieved via hydraulic means, however, compensation of liner wear can still involve plant shutdown and loss of production. Drift in discharge setting due to liner wear is still a major problem that must be addressed to improve product quality, consistency and reduce recirculating load. The continuous demand for better quality products and the high cost of reprocessing or discarding unsaleable material, highlights the need for re-examination of the technology associated with the crushers to ensure optimum control and system efficiency. A collaborative project between Pegson Ltd, one of the leading UK manufacturers of jaw and cone crushers, De Montfort University Leicester, and Transfer Technology plc was established to address the technological requirement for automation of the control of cone crushers. The machine chosen for the study is a 900 Autocone cone crusher manufactured by Pegson Ltd. The design philosophy is based on a mechatronic approach providing a complete solution through a distributed network of intelligent sensors, artificial intelligence technology and adaptive control. The modular design of the system ensures a progressive sophistication in technology that allows the automation to be phased in as required. This will ensure maximum benefits to all sectors of the aggregate industry. It is estimated that the automation will result in savings of around ten per cent. The savings will result from minimising the production of unsaleable products by reliable condition monitoring and automation of the control and maintenance of system parameters to optimise system efficiency. Extension of the methods and principles into the mining sector is anticipated. The control over the size of crusher product will offer great benefits to the mining industry with significant implications for subsequent milling and beneficiation processes.

Jan 1, 1995

By Tilley H. L

The 90 m deep Yallourn Open Cut brown coal mine in the Latrobe Valley, Victoria is developing into an area close to a reverse fault. A major batter stabilisation program, matched to ongoing operations, has com- menced to maximise coal recovery where the fault is within 100 m of the Open Cut. The various mine development options considered during the planning stages are outlined. These options were formulated in a back- ground of geotechnical constraints and the need to maintain continuous and reliable coal supply at a time when a new coal field would be developed. The geotechnical investigations and analysis procedures under- taken to determine stability of the batters during their excavation are presented. The geotechnical constraints on the mine design and opera- tions required to ensure safe working conditions are detailed. Current operational and batter stability conditions are considered satisfactory.

Jan 1, 1989

By Kazis JV

The beneficiation of fine coal has been the major problem facing the coal preparation engineer in recent years. The influence of clay slime, particle size and reagent type are but a few of the many factors that affect the recovery of fine coal. Laboratory test work has indicated that substantial increases in recovery could be achieved by improvements in technology in all these areas. Unfortunately, in most cases this technology has not carried through to the operating plants.

Jan 1, 1984

By L S. Shekhawat, M P. Roy, R K. Paswan, P K. Singh, A Joshi

Blasting in the mining industry is being transformed, and can no longer be treated as an art or a practice purely dependent upon experiences of individuals. Examples of key drivers that have demanded consistent and more accurate blast results are initiatives to control pit-wall damage to help mine steeper pit slope angles, to control damage to underground opening operating in close vicinity of the open pit mine. Such situation exists at Rampura Agucha open pit lead zinc mine, which is producing 5.7 Mt/a of ore and has started its underground part, which is slated to produce initially 2–2.4 Mt/a and 4.5 Mt/a in the near future. The open pit mine is currently working at 326 m depth and is designed to reach 421 m deep. It has been planned to operate the underground mine maintaining 50 m parting from the planned ultimate level of the open pit mine.Presently, open pit and underground mines are being operated simultaneously. The present average depth of underground working lies between 370 and 410 m below the surface level. Sometimes explosives up to 95 978 kg are being detonated in a blast round in open pit mine. These blasts are often apprehended as a danger to the safety and stability of underground openings. It was decided to document the impact of open pit blasting in the openings of underground workings, so that preventive measures may be taken for the safety and long-term stability of the underground mine. The impact of 86 open pit blasts has been documented in the underground openings and 258 blast vibration data has been recorded. The vibrations were recorded simultaneously in the roof, side walls and at floor levels. The highest levels of vibrations were recorded in the roof and the lowest levels at the corresponding floor levels. The pillars experienced lower level of vibrations than the roof. Blast designs were optimised at open pit mine to control vibration in view of long-term safety and stability of the underground openings. The vibrations generated due to detonation of explosives with shock tubes and electronic delay detonators have been recorded in underground openings for comparative assessment. Ground vibration recorded at roof, pillar and floor were analysed separately and threshold value of the vibration for the safety of underground workings has been determined based on the rock mass rating of the roof rock.CITATION:Singh, P K, Roy, M P, Paswan, R K, Shekhawat, L S and Joshi, A, 2015. Protection of underground mine structures due to adjoining open pit mine blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 279–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Supergene nickel sulphide ore mined currently by Agnew Mining Company is at times partially oxidised to sulphate. The resulting soluble nickel, and calcium and magnesium in mill water, are shown to act as depressants in flotation. The depressant effect is favourably selective in that violarite, the main nickel mineral, is less affected than pyrrhotite. Nickel recovery, however, is adversely affected, probably through reduced flotation of complex sulphides. Soda ash consumption is increased markedly by the presence of the cations as shown by operating data and pulp titration tests. A significant increase in concentrate grade, from 9% to 14% Ni, was achieved late in 1981. One of the changes in plant practice which contributed to this improvement was the addition of soda ash to mill feed rather than to flotation feed as before. It is shown by laboratory tests that this reduced the depressant effects of the cations, thereby improving recovery at the expense of rougher selectivity, or equivalently, increasing concentrate grade at constant recovery. The selective depressant effect cannot be exploited until scavenger recovery is improved and a scavenger concentrate regrind-retreat äcircuit is implemented. Development is

Jan 1, 1978