Search Documents

INDEX OF CONTENTSBlast Furnace SlagsForehearth AccretionsConverter SlagsConclusionsIllustrationsCOMPOSITION OF SOME COPPER SLAGS FROM PORT KEMBLASamples of copper slags from the Port Kembla Smelter of the Electrolytic Refining and Smelting Co. of Australia, Pty. Ltd., have been submitted for mineragraphic examination, with reference to the mode of occurrence of copper in them. The samples included (I) blast furnace slags, (H) a forehearth accretion, and (IH) converter slags. 1. BLAST FURNACE SLAGS Four series of samples of blast furnace slag have been submitted. The. chemical compositions of the several slags are shown in Table 1. Analyses Nos. 1 and 2 are of samples of slowly or normally cooled slag, taken from the slag dump, Analyses Nos. 3 and 4 are of samples comprising slowly or normally cooled slag, together with granulated slag from the same melt.

Jan 1, 1949

By E Jak, J Chen, B Hogg, S Nikolic, S Nicol

The quantity of post-consumer ‘waste’ materials generated each year is rapidly increasing. These materials can contain significant quantities of critical metals and present an environmental challenge if landfilled. The ISACYCLE™ technology is a proven solution for the processing of these materials. In the ISACYCLE™ furnace, the post-consumer materials are processed to recover energy along with any contained critical metals, in the form of a base metal alloy or matte. In addition, a clean aggregate (slag) is generated, which has the potential to be used for a range of applications in the construction industry. This slag is commonly based on a fayalite slag but is modified to manage the complex feed. This paper will review the fayalite slag system and the theoretical modifications required for treating urban wastes. Slags from an ISACYCLE™ furnace processing urban wastes have been sampled and characterised. The chemistry of these samples will be reviewed and compared to the expected theoretical modifications required.

Jun 19, 2024

By R Barritt, P Scott, K Albano

Successful closure of tailings storage facilities (TSFs) is an environmental issue faced globally by metalliferous mines. During the initial feasibility and design phase of the mine life importance is placed on the physical stability of above ground TSFs, largely driven by legislative requirements, whilst closure planning is often a secondary consideration. However, as the landform is further developed and constructed attention must be paid to regularly revisit the original closure plan and update it to achieve the best (sustainable) possible outcome for both the environment and stakeholders. A mine in northern Queensland is in the process of developing a closure strategy at their TSF. Appropriate closure measures for the TSF are required to mitigate the impact of any seepage emanating from the TSF on the groundwater and surface water receptors. O’Kane Consultants Pty Ltd (OKC) have provided the mine assistance with the development of a TSF cover system design in order to appropriately manage tailings during operations and to prepare for the facilities’ closure. OKC has collected data since 2007 from cover system field trials located on the TSF. To enhance engineering judgement in the design of future cover systems, calibration of soil-plant-atmosphere numerical models to field data (referred as ‘field response modelling’) were completed. Calibrated model inputs can be used to provide insight into long-term cover system performance as well as a tool for design of the final landform.Following a site investigation, materials characterisation and numerical modelling program various cover system alternatives were developed. Two of the preferred cover system alternatives referred to as Test Plot #1 (TP#1) and Test Plot #2 (TP#2) (Figure 1), were constructed at the site and instrumented. Monitoring instrumentation comprised several nests of in situ volumetric water content and thermal conductivity sensors to measure changes in water content, temperature and matric suction within the cover system materials and underlying tailings waste. Run-off collection buckets and a fully-automated meteorological station were also installed. CITATION:Barritt, R, Albano, K and Scott, P, 2016. Findings and conclusions following ‘long-term’ cover system monitoring – refinement of the conceptual design for tailings storage facility closure, in Proceedings Life-of-Mine 2016 Conference , pp 85–88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By W Patton

Investment decisions in the mineral resources sector are made on the basis of an assessment of the economic potential for a mineral deposit. Given the supporting information for the location, scale, and quantity of the commodity of interest, miners and investors aim to make risk-informed decisions when considering further investment. The objective of resource classification is the synthesis of various types and quantities of geologic information used in resource model construction to assign confidence categories to the estimated mineral resources, which can then be used to support informed economic decisions. In this paper a risk-based classification scheme for iron ore mineral resources using conditional simulations is presented. The method involves categorisation of each block according to a confidence level, considering expected recoveries from a kriging model over mining production volumes. The realisations of the simulated model are used to assign risk-based confidence categories to zones of the ore deposit. One motivation for this work is to assess the sensitivity of the scheme to geologic uncertainties. Specifically, that which uncertainty in the layout of mineralising alterations and weathering overprints influence variabilities of associated rock properties and the likelihood of obtaining expected ore recoveries. It is shown these risks have material implications for a project’s economic potential. How the scheme can be extended to the grade control context and the value subsequent grade control activities is also quantified.

May 24, 2023

By S Maryati

Surface mining activities disturb large areas, produce great sediment loads and tend to be a source of water pollution if they are not managed properly. Coal mining in Indonesia has a very high risk of soil erosion because the coal mining areas are generally located in tropical areas with a high average of rainfall (4000 - 6000 mm/year) and use surface mining methods. The main factors affecting erosion risk are climate, soil type, topography, vegetation cover and management factors. Thus, the monitoring of erosion risk in mining areas is very important due to the characteristics of coal mining in Indonesia. The objective of this research is to determine the ability of satellite images (remote sensing data) and geographic information systems (GIS) to provide an accurate and up to date spatial database for the monitoring of erosion risk in surface coal mining areas using the Universal Soil Loss Equation (USLE) method.The erosion risk analysis and spatial data processing are generated by the ArcGIS 9.3 software and need several data, namely: an erosivity map, erodibility map, a slope map, vegetation index map and land management or land cover map. The erosivity map is derived from the rainfall data, whereas the erodibility map is derived from the soil map. The slope map is derived from the SRTM-DEM (Shuttle Radar Topography Mission-Digital Elevation Model) and processed using 3D analyst tools. Furthermore, the vegetation index map and land cover map are derived from a satellite image using digital image processing techniques.This preliminary study produced results that show soil erosion monitoring, which is integrated with remote sensing and GIS technologies, has great potential for producing accurate, advance, and low cost erosion risk maps in coal mining areas. This map is very important for getting spatial distributions of the erosion and useful for developing erosion management plans.

Nov 22, 2011

By C DahnTr-Lindqvist

The Kiruna mine produced about 19 Mt processed iron ore in 1999 using sublevel caving. General failure in the hangingwall has been widely studied and its mechanism is rather well understood. Failure in the footwall is more recent and not perfectly explained. Plane shear failure and Hoek and BrayÆs circular failure charts were successfully used to match the first surveyed failure surfaces. The footwall is not free yet but covered by a caved waste rock abutment whose exact behaviour is poorly known. Based on new field data and numerical models (FLAC), the following paper presents recent improvements in understanding the Kiruna mineÆs footwall failure process.

Jan 1, 2000

By Green A. D M

The establishment of the Imperial Smelting Furnace at Sulphide Coporation Pty. Limited for the smelting of zinc and lead made it necessary to design and install sintering capacity to produce approximately 500 t.p.d. of zinc-lead sinter. The updraught sintering process installed is a recent development and the plant was designed with adequate flexibility and equipment to enable operating staff to investigate the process and achieve maximum production under optimum operating conditions.Sulphur dioxide gases from the sinter machine are passed to a contact acid plant for the manufacture of sulphuric acid.

Jan 1, 1964

By Reichman J. P

Extensive use is made of a small scale computer (IBM 1130), in the calculations of ore reserves for Western Mining Corporation's nickel mine at Kambalda, W.A. All surface drilling data such as assays, density and location information, are stored on disk files at the Company's Technical Computing Centre at Perth, W.A. The computer is used to search through the data, select significant ore intersections, calculate the area of influence of each intersection and perform the necessary calculations to arrive at an estimate of the ore reserve. Comparing the computer-assisted ore reserve calculation with an entirely manual operation, it is estimated that a saving of 40 percent in time is achieved together with

Jan 1, 1973

By D Fukuda, K Kaneko, R Kudo, J Kodama, Y Fujii, T Sasaki

"Estimation of stress state as well as elastic modulus is important for the prediction of a rock slope deformation in an open pit mine since it can strongly influence the mining-induced deformation of the rock slope. This study applies a method to evaluate regional stress state and Young’s modulus by analysing the mining-induced deformation of ground. The effect of changes in regional strain state due to tectonic plate motion can be accounted for using the proposed method. Mining-induced deformation can manifest itself as changes in ground surface geometry resulting from mining activity. There are three underlying factors that can contribute to the deformation: displacement induced by the effect of gravity displacement induced by the effect of horizontal regional strain incremental change in the horizontal regional strain. The relative displacement arising from the mining excavation at the Torigatayama limestone mine in Japan has been measured by Global Positioning System (GPS). Both the regional stress state and Young’s modulus were estimated by back analysis of the change in distance between GPS stations using a 3D finite element method. It was shown that the reliability of the estimation improved with an increase in displacement due to mining progression. It was also shown that values for Poisson’s ratios of less than 0.10 are reasonable estimates with values for Young’s modulus between about 5?GPa and 10 GPa. The magnitude and direction of the maximum compressive stress in the district surrounding the Torigatayama mine were estimated to be between -6.4 MPa and -4.4 MPa and around N25E respectively.CITATION:Kodama, J, Sasaki, T, Fukuda, D, Kaneko, K, Fujii, Y and Kudo, R, 2014. Estimation of regional stress state and Young’s Modulus of ground at Torigatayama Limestone Mine in Japan, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 135–142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By K Aikawa, M Ito, K Mitsuhashi, Y Ebisu, J V. Satur, I Park, N Hiroyoshi, T Suto

Copper concentration using flotation is becoming more difficult, because of an increase in ore complexity accompanied by smaller grain sizes of copper minerals than usual, requiring finer grinding in order to liberate them. Project Arqueros, located at the mid northern part of Chile, is a copper mine project with an orebody consisting of various sulfides such as chalcopyrite, chalcocite, and bornite. Some of the copper minerals in Arqueros show low floatability mainly because of their fine grain size and resulted fine grinding size, and also because of the complex mineralogical composition. For example, chalcopyrite in Arqueros floats less than the other copper sulfide minerals. In this study we carried out some kinetic flotation tests with the Arqueros ore using a laboratory-scale forced air type flotation machine by varying the regrinding size. The products were assayed and mineralogically analysed to compare the minerals in their flotation behaviour with respect to size classes and liberation classes. The results were compared with a model calculation according to bubble size measurement. From the flotation testing and mineralogical analysis, it was found that copper minerals of the same size and liberation class floated at the same rate even with different regrinding size. At the same time the comparison between experiment and calculation showed that the fine particles of less than 5 µm size floated faster in actual than in the model applied. These results suggested that interactions among minerals of different species and of different sizes had positive impacts on the flotation rate of the fine particles. It indicates that this phenomenon can be applied to improve copper recovery in the project.

Aug 24, 2022

Organisations are starting to develop processes for achieving sustainability principles they have defined for their organisation. The foundation for these principles is now well accepted. The definition of a sustainability framework is a good starting point for any project. The delivery of the framework requires the organisation to think differently about how project objectives can be met. New tools are becoming available to help achieve the sustainability outcomes for the projects. This paper will examine the project building blocks that are necessary to ensure the sustainability framework can be achieved for the project. These include new approaches to decision-making processes and evaluation tools and when to apply them. An integrated approach with shared expertise to project delivery, which is applicable to the whole supply chain, will be discussed. This will cover sustainability procurement, integrated waste management, cleaner production and eco-efficiency, sustainable products and disposal. A project toolkit will be presented and some key project tools identified. The need for management support in undertaking these new approaches is critical, as is the need to develop partnerships and cooperative management to facilitate delivery.

Jan 1, 2004

By S Utili, A Agosti

The Overall Slope Angle (OSA) of pitwalls plays a crucial role in the financial return of an open pit mine. In current practice, pitwall profiles are designed to be planar in cross-section within each rock layer, ie the profile inclination across each layer tends to be constant. A new slope design software, OptimalSlope, has been recently proposed to determine the geotechnically optimal profile shapes for the pitwalls of mines. OptimalSlope seeks the solution of a mathematical optimisation problem where the overall steepness of the pitwall to be designed is maximised for an assigned stratigraphy, rock properties (unit weight and strength) and Factor of Safety. The geometry of the benches is provided as input to OptimalSlope. The results obtained so far on three mine case studies in isotropic rock masses (Utili et al, 2022; Agosti et al, 2021a, 2021b) show that optimal profiles are up to 5° steeper than their planar counterparts – ie the planar profiles exhibiting the same FoS – leading to realising significant saving on waste rock and as a consequence Net Present Value increments and carbon footprint reductions. OptimalSlope algorithms have been modified to deal with anisotropic rock masses characterised by direction dependent shear strength. In the paper, the case of rock masses in banded iron formations (BIF) is tackled. A data set of anisotropic rock shear strengths typical of Western Australia is considered. The Snowden modified nonlinear model was employed to characterise the anisotropy of the rock mass shear strength. From the OptimalSlope simulations performed emerges that optimal pitwall profiles can increase significantly the Overall Slope Angle in comparison with planar profiles featured by the same Factor of Safety. LEM stability analyses of all the profiles were also performed by Rocscience Slide 2 to independently verify the FoSs of the optimal profiles obtained.

Nov 29, 2022

By Glassock C. D

Most Australian mining projects are becoming smaller, more remote and with lower grades of ore. Their small size has been making it harder for mining companies to absorb the large infrastructure costs. This has forced companies to reduce those costs in every way they can. Social factors, environmental groups and even tax laws have added other pressures to force down the infrastructure costs for remote projects. For the last ten years, the downward trend in costs has been marked. It seems certain to continue for years into the Future.

Jan 1, 1997

By R Norris, M Dunne

Substantial efforts by the industry, as well as by process and equipment designers, have resulted in many innovative developments that provide cost effective reductions in water usage. This paper showcases four emerging best practices in industry including examples of recent installations. Belt press filters are a small fraction of the operating and capital cost of alternative ædryÆ tailings technologies. This gives operators who must ædryÆ their tailings a competitive advantage and makes such operations much more sustainable. The new generation of belt filter presses use less energy, produces lower cake moistures and better disposal stacking properties. The need for tailings storage facilities may be eliminated or in some cases high-grade tailings can be dewatered and sold as a low value product. Mining applications include sand tailings, sinter plant waste, coal tailings and power station fly ash. Flip-flow screening machines are proven worldwide in the dry classification of coal and other minerals, reducing the size of beneficiation plants, whilst reducing energy, water demand and media consumption. They also allow the screening of wet/sticky materials not able to be sized using conventional screens. Lamella separators are used for toxic water clarification and/or sludge thickening in many downstream metal industries with the underflow often dewatered in a belt filter press. Such low cost, high capacity thickeners could also be used instead of conventional thickeners at smaller mines. The simple and reliable continuous washing upward flow (CWUF) sand filters have been used for treatment of waste water from coal preparation plants and steel works as well as in the production of potable water. The filtered waste water from mining processes can then either be reused or discharged from site. Other installations include cleaning mine water to prevent the blocking of dust suppression spray nozzles.

Jan 1, 2006

By R Norris, M Dunne

Mining and mineral processing is expected by society and obliged by law to operate in an environmentally friendly fashion, minimising the impact on and avoiding damage to the environment. Substantial efforts by the industry, as well as by process and equipment designers have resulted in many innovative developments, which show that operating in an environmentally responsible manner can be achieved in a cost-effective way. This paper showcases five emerging equipment best practices in industry including installation examples. Flip-flow screening machines are proven worldwide in the dry classification of coal and other minerals, reducing the size of beneficiation plants whilst reducing energy, water demand and media consumption. They also allow the screening of wet/sticky materials not able to be sized using conventional screens. The belt press filter is a small fraction of the operating and capital cost of alternative dry tailings technologies. This gives operators who must dry their tailings a competitive advantage and makes such ægreenÆ operations much more sustainable. The filtercake is disposed with other plant rejects, eliminating the need for tailings dams to be constructed and thus also often increasing mine reserves. Mining applications include coal tailings, sand tailings, sinter plant waste and power station fly ash. Screen-scroll and vibrating centrifuges are widely used in the coal, potash and salt industries to dewater the product to low surface moistures. Inclined plate Lamella separators are used for toxic water clarification and/or sludge thickening in many downstream metal industries with the underflow often dewatered in a belt filter press. Such low cost, high capacity thickeners could also be used instead of conventional thickeners at smaller mines. The simple and reliable continuous washing upward flow (CWUF) sand filters have been used for treatment of waste water from coal preparation plants and steel works as well as in the worldwide production of potable water. The filtered waste water from mining processes can then either be reused or discharged from site. Other installations include cleaning mine water to prevent the blocking of dust suppression spray nozzles.

Jan 1, 2006

By J Coombes, R Sterk

The efficiency of the Australian and New Zealand stock exchanges relies on a fully informed market: shareholders and investors are fully and transparently informed of all material information relating to the shares. These principles of transparency and materiality are similarly core to the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the JORC Code). The JORC (Joint Ore Reserves Committee) Code also includes a principle of competency to ensure that the person providing the material information for public disclosure is suitably qualified and experienced.Since its inclusion into the ASX (Australian Securities Exchange) Listing rules in 1989, the JORC Code has continually improved and evolved in attempts to meet the market’s need for competent, transparent and informed disclosure. The quality and effectiveness of Public Reporting in accordance with the JORC Code is under constant challenge: some practitioners argue there is insufficient regulation, while others argue the need for greater self-regulation.This paper contributes to that discourse by exploring how well the Reporting expectations are met, and, whether Public Reporting in accordance with the JORC Code has a material impact on share-price movement.CITATION:Sterk, R and Coombes, J, 2017. Public reporting – new standards or no standards?, in Proceedings Tenth International Mining Geology Conference 2017, pp 423–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By C J. Unger, T Baumgartl, C J. Bond, P Sabourenkov, V C. Glenn

Social licence to mine is influenced by society’s perception of the mining sector’s ability to effectively rehabilitate mined land and for governments to appropriately regulate that process for the broader community benefit. In Queensland, Australia, many mine rehabilitation personnel working for active coalmines, as either staff, consultants or contractors, belong to the Central Queensland Mine Rehabilitation Group (CQMRG). The CQMRG was established 23 years ago with the aim of sharing informal knowledge related to practical aspects of rehabilitation in order to leave as positive a legacy as possible from mined land. This voluntary group of professionals also includes members from regulatory agencies and civil society. Within the dynamic regional mining environment, mine rehabilitation professionals benefit from sharing their informal knowledge.CQMRG is currently a group in transition. Mining boom and downturn cycles have exacerbated the loss of accumulated knowledge in the core CQMRG membership due to rapid changes in personnel at mines in the region. Additionally, some of the most experienced CQMRG-affiliated rehabilitation practitioners are approaching the end of their careers and want their valuable and less formal knowledge retained. This paper discusses the development of a research project that emerged in response to the anticipated loss of several decades’ worth of valuable knowledge as rehabilitation practitioners in CQMRG left the region or the workforce.CITATION:Unger, C J, Bond, C J, Baumgartl, T, Glenn, V C and Sabourenkov, P, 2016. ‘MRC-wiki’ – a mine rehabilitation and closure knowledge management tool for Central Queensland coalmine practitioners, in Proceedings Life-of-Mine 2016 Conference , pp 39–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By H F. Yu, S Ueda, J Diao, W F. Gu, Y Sasaki, H Qin

The main reason for the underutilisation of steelmaking slags is their instability, which is influenced by their complex phase structure. Recycling and sustainable steelmaking slag face challenges due to the presence of magnesium oxide (MgO), a crucial component in steelmaking slag. This study investigates the phase evolution of steelmaking slag during the cooling process with different MgO contents, using high-temperature experiments and FactSage™ software, ver 8.1, (by Thermfact/CRCT and GTT-Technologies) thermodynamic equilibrium calculations. X-ray diffraction (XRD) and scanning electron microscope - energy dispersive x-ray spectroscopy (SEM-EDS) analyses identified main phases in steelmaking slag, including Ca2SiO4 (C2S), RO (MgO-FeO solid solution), Ca2Fe2O5 (C2F), and Ca3SiO5 (C3S). The study reveals that RO phase increases as the MgO content increases. C3S precipitates from steelmaking slag with a 12 mass per cent MgO content at a reduced temperature of 1400°C. It is important to note that C3S remains in the steelmaking slag even after slow cooling. This may be due to the substitution of Ca2+ in C3S by Fe2+ and Mg2+ ions. Intriguingly, the precipitation of f-CaO in steelmaking slag with 10 mass per cent of MgO content occurred after one year, while there was no manifestation of f-CaO precipitation in the steelmaking slag with 12 mass per cent of MgO content even after one year. This discrepancy suggests a potential stabilising effect of an appropriate amount of MgO in steelmaking slag. However, it is crucial to emphasise that this inference lacks supporting data, necessitating further research to validate this hypothesis. The significance of this work is in uncovering the complexities of steelmaking slag behaviour, providing essential insights for optimising recycling processes. The research sheds light on the factors that influence the phase composition and stability of steelmaking slag, contributing to the utilisation of steelmaking slags, promoting environmental sustainability, and enhancing the overall efficiency of metallurgical processes in the current industrial landscape.

Jun 19, 2024

By A S. Derrington

High-accuracy, solid-state digital reference barometers have proven to be well suited to conducting underground barometric pressure surveys. The only problem is their expense; at least A$4000 each. For this reason, and because barometric pressure surveys are not a routine undertaking, very few mines have been able to justify the purchase of suitable instruments. The author knows of only three Australian metalliferous mines that own them.However, this may soon change given the recent development of low-cost, mass-produced miniature barometric pressure transducers. These transducers were developed to provide an altimeter function in the latest generation of smartphones. The main purpose of the inbuilt altimeter function is to allow the smartphone to be aware of its altitude when the global positioning system satellite signal is lost.This paper describes a prototype barometer that was constructed using one of the most accurate of the latest generation of piezo-resistive smartphone barometric pressure transducers. The prototype instrument was constructed for less than five per cent of the cost of a commercially available digital reference barometer. The prototype was subsequently tested against a reference barometer at the University of Queensland’s Experimental Mine to verify its accuracy and suitability for measuring pressure differences between underground survey stations.It is expected that the instrument’s low cost will pave the way for barometric pressure surveys to become more commonly used in mines. In turn, the resulting improvement in knowledge of major underground pressure losses should allow mine ventilation officers and engineers to optimise their ventilation systems and potentially reduce overall operating costs.An alternative option would be to use a barometer-equipped smartphone as a survey instrument, provided that its inbuilt barometer module is sufficiently accurate.CITATION:Derrington, A S, 2015. Development of a low-cost instrument for barometric pressure surveys, in Proceedings The Australian Mine Ventilation Conference, pp 331–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J Herd, J Rowe, M Cutbush, d F. Aziz

WearApp provides expertise for assessing the degradation of removable screening media panels on vibrating screens right in a user’s pocket. Through the WearApp application, users can simply take a picture of a panel using their mobile, enter some basic information and have the application assess the wear to provide a recommendation for whether the panel needs to be replaced. Where traditional mechanisms for assessing panel wear only measure a few points across the panel face and rely on having personnel with specialised knowledge available to perform the assessment, WearApp uses deep learning models to analyse the entire panel face and support the user to make an informed decision. The application works through analysing a panel image and using a model to automatically detect the corners of the panel. Given the known dimensions of the panel, this enables the application to calibrate the pixel size against a known reference. A second set of models then detect the apertures and measure their dimensions. With the aperture dimensions defined the application assesses the wear of the panel through referencing a stored 3D model of the aperture. Finally, the data from each aperture is collated and the wear of the entire panel face defined. Since WearApp performs measurement of the entire panel face, it also allows the user to perform a more detailed analysis of the panel’s wear profile. Where typically, the panel wear is only measured in a few locations, WearApp’s analysis enables users to visualise the panel wear across the entire panel face, identifying areas of high wear that could be leading to premature panel replacement. Additionally, because the entire panel face is measured the change in screening efficiency can be calculated accurately for the worn panel, even taking into account the impact of aperture pegging by small rocks.

Sep 1, 2024