Search Documents

By P Thompson, B W. Atkinson

Water treatment is not æcore businessÆ for mining companies.Just as mineral ores and coals are unique, each requiring detailed characterisation and pilot-testing to determine their optimum beneficiation route, so too are mine waters, each requiring careful assessment to determine the most appropriate treatment. There are many cases of æregret capitalÆ expenditure, whereby mines have installed off-the-shelf equipment only to find it inadequate for their purposes or grossly expensive and labour intensive to operate.Water may be required for potable purposes, ore processing, dust control and/or irrigation. A major driver will frequently be environmental constraints for off-site discharge. Mine water projects can become very complex, and detailed models need to be prepared and optimised to properly consider the raw water sources, the on-site storages, the on-site uses and the off-site discharges, as well as handling the residuals (by-products) of water treatment. By-products may be in the form of concentrated backwash streams or streams of elevated salt content. Careful management of the by-products is required to avoid recontamination of the source water.Regulators often drive mine owners toward reverse osmosis (RO) so that their discharges can be considered as æzero dischargeÆ in terms of potential pollutants. Such decisions need to be based on site-specific information rather than any form of æblanketÆ requirement. An analogy is that many humans like to consume mineral water rather than ænormalÆ tap water. Receiving environments also accommodate or even prefer their æmineralsÆ and so RO is neither warranted nor sustainable in many cases.This paper presents two case studies for operating mine sites, both of which have a significant excess of water requiring environmental discharge. The examples demonstrate a sensible balance between treatment type, environmental constraints, process implementation and residuals management. LIMN« æthe flow sheet processorÆ was used to model one of the case studies due to the complexity of the water system on that site.CITATION:Atkinson, B W and Thompson, P, 2013. Mine water - optimising for site and environment, in Proceedings Water in Mining 2013 , pp 9-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By E Macmillan

For any processing plant there will be deleterious elements or minerals which affect production or quality, and a strategy to predict their occurrence and mitigate their impact is required. An early objective of the Olympic Dam geometallurgy program was prediction of the acid consumption and gelling behaviour of the ore, which affects leach recovery, throughput and circuit availability. The geometallurgical test program measured the response of a wide range of ore types, and then relationships between mineralogy, metallurgy and chemistry were developed. Thus the drivers of acid consumption and triggers for gelling events could be described in ways that were meaningful to plant operations.To enable optimisation of the mine planning and ore blending processes, the parameters driving metallurgical response must be translated to the block model. Data support is critical in populating a block model. Assay information is easily obtained, but mineralogical and metallurgical information is more expensive and time consuming to collect. Hence population of a block model with mineralogical and metallurgical values using a conventional geostatistical approach is not always possible.An alternative approach employed at Olympic Dam was the development of a suite of assay-to-mineral algorithms. These algorithms were calibrated using all available mineralogical information, and this enabled the calculation of mineral abundances for more than 1.5 million assayed samples. Estimation of the minerals in the block model, and the generation of acid consumption values for each block could subsequently occur.The use of back-calculated mineralogy from assays as part of process model generation is an innovative tool which can be used for mine planning and optimisation and to ensure the plant does not receive any unwelcome surprises. Ultimately, one purpose of geometallurgy is to predict potential processing issues and their drivers so that these can be mitigated. A strategy to achieve this is outlined hereafter.

Sep 5, 2011

By R P. Varden

This paper looks at the design of the Bentayga raisebore with subsequent back analysis using a LiDAR survey. A search for LiDAR raisebore assessment publications shows little work has been done on this subject. The paper examines the empirical design and RS2 modelling assessment with the bored condition. The high resolution of the LiDAR enabled mapping of weak structures that were located on the geotechnical investigation hole the orientations of which could not be determined. In addition, the scan showed were water ingress was occurring, potential stress overbreak and structural controls on stability. The LiDAR results were able to confirm no additional support work such as a shotcrete liner is necessary. The LiDAR results have been analysed in one metre increments as volume of overbreak against the empirical stability criteria (McCracken & Stacey 1989). The future use of LiDAR mapping over a range of rock mass conditions will provide quantification of the established empirical assessment improving its reliability. It is also a useful and accurate tool to monitor long term stability of a raisebore due to stress change or ore pass due to wear.

Mar 15, 2021

By J S. J van Deventer

"Conventional wisdom is that gold not assayable is not recoverable or does not exist. There has been no formal study on the possibility that gold assays using advanced spectroscopy such as mass spectrometry and neutron activation could grossly underestimate the gold recoverable by proprietary extraction techniques. Such gold is not considered here to be æinvisibleÆ to detection but rather æabnormalÆ or ædistortedÆ at atomic level. Large-scale extraction of gold from æabnormalÆ ores has not been demonstrated, hence this emerging field still lacks credibility and acceptance. For fear of harming their reputation, few academic researchers or companies are expected to venture into this field until it is well proven. This paper aims to create awareness amongst metallurgists of the potential of æabnormalÆ gold ores by reviewing unconventional observations, the pseudoscience mainly available in non-peer reviewed web sites, and hypotheses for the recovery of ænon-assayableÆ gold, including: the occurrence of high levels of nano-sized gold in clays detectable by high-precision analytical instruments, which represents æinvisibleÆ gold accounts of ambient transmutation of elements, mainly using thermal methods orbitally rearranged monoatomic elements (ORMEs), which are virtually undetectable by conventional means, and their conversion to normal metals the possibility of a æhigh spinÆ state of transition metals the formation of microclusters altering the chemical behaviour of gold and the possibility of clustering with other elements. It is suggested here that gold in ores displays a range of clustering, from ænormalÆ gold amenable to conventional extraction to the ORME state. The concepts of æintermolecular waterÆ in forming complex salts locking up precious metals, electro-dissolution in strong acids, and electrowinning at both the anode and cathode are discussed as a means of treating æabnormalÆ gold ores. It is also possible that the gas phase extraction of gold chlorides under controlled temperature and pressure conditions, as well as transferred-arc plasma fuming of gold through carbothermic reduction of sulfides, could be used as a basis for extraction of gold from æabnormalÆ ores.CITATION:van Deventer, J S J, 2013. Is there gold that we do not recognise?, in Proceedings World Gold 2013, pp 27-34 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

The preamble to the mining Act sets out that such Act is to provide for the encouragement and regulation of mining within the State of Queensland. This paper will attempt to follow the legislative path of such aim and in particular to show what part Mining Wardens play in the administration of the Mining Act.The Mining Act empowers the Governor in Council to constitute Mining Districts and Mining Fields and to appoint any duly qualified officer of the Public Service of Queensland to be a Warden or a Mining Registrar. As a matter of practice Stipendiary Magistrates who hold office in the major centre within a Mining District are appointed Wardens and Clerks of the Court are appointed Mining Registrars. In some districts where there is no Stipendiary Magistrate the Clerk of the Court is appointed an Acting Warden with all the powers of a Warden. Every Warden so appointed is a Warden for the whole State.To achieve impartiality Section 74 of the Mining Act provides that a Warden shall not hold or be entitled (directly or indirectly) to the benefits of any share or interest in a mining tenement or mining venture and provides a penalty of $1000 or imprisonment for six months or both, for contravention of such section.

Jan 1, 1986

By N Cusworth, W R. Mackenzie

"In 2007, the authors presented a framework for the conduct of resource project feasibility studies and provided guidance on minimum standards and best practice (Mackenzie and Cusworth, 2007).This paper will present the authors’ observations in relation to feasibility studies undertaken to support investments made during the unprecedented period of resource project capital investment since 2007. It will also provide comments on general trends in the mining industry’s approach to project assessment and update recommendations on best practice.CITATION:Mackenzie, W R and Cusworth, N, 2016. The use and abuse of feasibility studies – has anything changed?, in Proceedings Project Evaluation 2016, pp 133–148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By S G. Hagemann, M E. Barley

The Mt Tom Price deposit is a world-class high-grade hematite deposit in the Hamersley Province of Western Australia with an original resource of 900 Mt of almost pure hematite, averaging 63.9 wt per cent Fe. Petrological and geochemical studies at both the Southern Ridge and the North deposit at Mt Tom Price have identified three hypogene alteration zones between unmineralised BIF and high-grade iron ore: distal magnetite-siderite-stilpnomelane; intermediate hematite-magnetite-ankerite-talc-chlorite; and proximal martite-microplaty hematite-magnetite-apatite alteration zones.Fluid inclusions trapped in siderite within the distal magnetite-siderite- stilpnomelane alteration zone at the North deposit revealed primary high salinity (25.5 eq wt per cent NaCl-CaCl2) inclusions that homogenised between 107¦ and 142¦C into liquid. Fluid inclusions trapped in ankerite within ankerite-microplaty hematite veins in the intermediate hematite-ankerite-magnetite-talc-chlorite alteration zone at the North deposit revealed mostly H2O-CaCl2 pseudosecondary and secondary inclusions with salinities of 22.4 - 25.4 eq wt per cent and 22.9 - 25.9 eq wt per cent CaCl2, respectively. Pseudosecondary inclusions homogenised between 153¦ and 449¦C and secondary inclusions homogenised between 103¦ and 157¦C. Fluid inclusions trapped in apatite within talc-microplaty hematite veins in the intermediate hematite-magnetite-talc-chlorite-apatite alteration zone at Southern Ridge revealed that primary, medium salinity (7.0 - 9.0 eq wt per cent NaCl) inclusions homogenised between 181¦ and 257¦C and primary high salinity (22.8 - 25.9 eq wt per cent CaCl2) fluid inclusions homogenised between 118¦ and 257¦C into liquid. Microthermometric analysis of quartz from quartz-hematite veins from the Southern Batter Fault, Southern Ridge show a complex fluid inclusion history. Primary fluid inclusions consist of: low- and high-salinity H2O-NaCI inclusions trapped at temperatures of approximately 140¦ to 230¦C; vapour-rich inclusions of unknown compositions; and æcomplexÆ salt-rich (Ca, Mg, K and Na inclusions).Secondary inclusions consist of medium-salinity fluid inclusions trapped at temperatures of about 140¦ to 280¦C.A two-stage hydrothermal model is proposed for the formation of both the Southern Ridge and North deposits. Early 1a hypogene alteration involved the release of hydrothermal NaCl-CaCl2-rich (25.5 eq wt per cent) basinal brines (110¦ - 150¦C) from the underlying Wittenoom Formation and directed upward along normal faults and focused within the silica-rich rocks of the Dales Gorge Member, by the shales of the underlying Mt McRae Shale Member and overlying Whaleback Formation. Within the Dales Gorge Member hydrothermal basinal brines migrated laterally within large-scale folds with permeability controlled by shale bands and the NW trending dolerite dyke sets. Fluid rock reactions transformed unmineralised BIF to magnetite-siderite-iron silicate BIF, with subsequent desilification of the chert bands. Stage 1b hypogene involved an increase in temperature of the hydrothermal, CaCl2-rich saline (24 eq wt per cent) basinal brines (250¦ - 300¦C) resulting in formation of hematite-ankerite-magnetite-talc-chlorite alteration and the crystallisation of microplaty hematite. Late stage 1c hypogene alteration involved the interaction of low-temperature (~120¦C) basinal brines with the hematite-ankerite-magnetite mineral assemblage. At the Southern Ridge deposit this process was very intense (ie high fluid flux), therefore resulting in the almost total removal of ankerite and resulting in the increased porosity of the ore. Stage 2 supergene enrichment in the Tertiary resulted in the removal of residual ankerite and apatite and the weathering of the shale bands to clay.

Jan 1, 2005

By A Takahashi, Y Uchisawa, M Hayashi, T Watanabe, M Susa

Owing to the deterioration of iron ore, the Al2O3 concentration in iron ore increases, and thus it is important to investigate the effect of increment in Al2O3 concentration on the microstructures of iron ore sinters. During the sintering process, a melt is present in the sinter for only a few minutes, and therefore the microstructure of the sinter doesn’t reach thermodynamic equilibrium. Nevertheless, the formation process of the microstructures can be interpreted and predicted to some extent from the equilibrium phase diagram. This study investigated the liquidus isotherm in the CaO-SiO2-Fe2O3- 5 mass% Al2O3 system at 1240°C in air and the phase equilibria of silico-ferrite of calcium and aluminium (denoted by SFCA) and SFCA-I by XRD (X-ray diffraction analysis) and electron probe micro analyzer (EPMA). The following results were obtained: 1. The ferrite melt region with a high Fe2O3 concentration shifts to the lower Fe2O3 side than the liquidus isotherm in the CaO-SiO2-Fe2O3 system. 2. The compositional region of SFCA extends in the CaOꞏ3Fe2O3-4CaOꞏ3SiO2 direction than the silico-ferrite of calcium (denoted by SFC) composition region with a 0 mass% Al2O3. 3. SFCA-I is observed in the present system, which suggests that the increment in the Al2O3 concentration contributes to the stability of SFCA-I. These results imply that an increment in Al2O3 concentration in iron ore leads to a decrement in the volume fraction of the bonding phase and that the fraction of the SFCA phase increases, and those of 2CaOꞏSiO2 and slag phases decrease in the bonging phase. The SFCA-I phase is also precipitated from the slag with an Al2O3 concentration around 5 mass%.

Jun 19, 2024

By D Howe

The Athena gold deposit was discovered in 2007 by Gold Fields Australia Ltd, at the St Ives Gold Mine, 35 km southeast of Kambalda, Western Australia. Gold anomalism was identified in sheared Paringa Basalt as a result of a regional scale aircore drilling program, in association with geophysics. In the 18 months following discovery, the deposit was intensely drilled and by June 2009, it was announced that the Athena deposit contained an ore reserve of 1.7 Mt @ 5.6 g/t for 316 koz. This was followed by a feasibility study, and as a result mine development commenced in November 2009.The Athena mineralisation is hosted in a discrete, north-south striking, steep to moderately dipping shear zone within the southwest dipping Paringa Basalt. Vein intensity has a strong correlation to grade and vein type varies from early thin quartz-albite-sulfide (pyrite and/or pyrrhotite) shear parallel veins to strong brecciation and irregular veining with quartz-albite-actinolite-biotite-pyrrhotite infill. The geology preproduction process developed at the Argo mine was refined and improved following a business improvement project. The aim of the process is to construct detailed geological interpretations prior to development allowing informed mining decisions to be made. The process delivers significant cost savings and revenue enhancements.The development of macroscopic classification scheme was critical to determine ore or waste in the early phases of mining. The Style of Deformation, Alteration and Veining (SAV) Code was the result, and has been enhanced as greater geological knowledge is gained over time.

Aug 22, 2011

By J Zhou, L Crompton, K P. Galvin, J L. Sutherland, C P. Lowes, C Bezuidenhout, J Bijzet

Platinum Group Metal (PGM) bearing ores from the Upper Group 2 (UG2) reef often contain significant concentrations of chromite which can potentially be upgraded to produce a saleable product. A common approach is to implement gravity separation on the PGM flotation circuit tailings. However, where the particle size range of interest is broad and the lower size limit ultra-fine, the challenge is how to maximise the recovery at a saleable product grade without compromising throughput. This study was concerned with the performance of a REFLUX™ Classifier for beneficiation of a PGM bearing chromite ore and the benefits of size classification. The sample had a nominal top size of 0.5 mm and was processed over the complete size range and in two discrete size classes following classification at 106 µm. The primary goal was to produce a concentrate exceeding 40 wt. per cent Cr2O3, ideally approaching 42 wt. per cent Cr2O3, with minimal PGM losses above 106 µm. A major challenge was to process at the required solids throughput in a single stage with the feed pulp density constrained to a nominal upper limit of 30 wt. per cent solids. It was found that varying the controller density set point of the REFLUX™ Classifier produced strong control of the product grade. Products as high as 41.1 wt. per cent Cr2O3 were produced at 78.6 per cent recovery for the +106 µm material, while in the −106 µm portion the product grade was as high as 41.4 wt. per cent Cr2O3 at 83.2 per cent recovery. Processing the feed in discrete size classes enabled the volumetric feed and fluidisation rates to be optimised for a given application; hence, superior performance was achieved at the finer sizes. This work has demonstrated the value in considering feed preparation as well as technology selection in developing a robust process solution.

Aug 24, 2022

The Australian coal industry has undergone sevenfold growth over the last 30 years and since 1985 has been the world's largest coal exporter. Three quarters of Australia's coal production is exported so its future is dependent on it remaining internationally competitive with other energy sources and other coal exporting countries. Coal is likely to increase its share of the energy market during the nine- ties as oil prices increase, new coal-fired capacity is commissioned and some form of nuclear energy is developed which is of acceptable safety standards to the community for use in the 21st century. Gas may take a part of coal's anticipated market share by the Year 2000. While coal exports will increase from China, Colombia, Indonesia and Venezuela and satisfy some of this additional coal demand Australia will also expand its export production, due to its existing advantages. The United States, Canada, South Africa, Poland and USSR seem unlikely to enjoy the same degrees of expansion and some, particularly Poland and USSR, will decline. Australia will always find it difficult to compete in the more distant markets due to levels of ocean freight, although its high quality coals will tend to partly offset such disadvantage.

Jan 1, 1988

By D P. Blair

There are two major aspects to wall control blasting – the potential for any blasthole to cause wall damage and the potential for a delayed sequence of blastholes to cause damage. The damage potential of individual blastholes is governed by standoff distance and charge weight. However, for locations sufficiently close to a highwall, dynamic finite element models and field measurements show that there is also a critical nature to those blastholes very close to the wall, over and above standoff distance. At many mine sites, the charge weight/standoff-distance is set by trial and error. Thus, a significant aspect of the present work is the determination of dynamic stress radiating from a blasthole. Unfortunately, the modelling and measurement of this dynamic stress is still faced with many difficulties. Typical models have questionable aspects, which casts serious doubt over their predictions, and it is shown that the Hustrulid Bar experimental technique does not correctly account for stress wave attenuation in extended media. In an attempt to solve the dynamic stress problem, the present work describes a model based on an exact solution under the assumption of viscoelastic material. The model takes full account of the rock mass elastic/viscoelastic properties, the explosive type, geometry and primer location and predicts a dynamic stress for direct comparison with the unconfined compressive strength of the local rock mass. This model predicts the standoff distance required to avoid damage due to a single blasthole. The behaviour of a delayed sequence of blastholes is analysed using an upgraded waveform superposition model, covering a range of initiation delay combinations, which predicts the peak particle motion (PPM) induced in the wall for each combination. This approach shows that there is no need to fire dedicated trim shots close to walls; all that is required is a carefully modified production shot. The mechanism of vibration screening is discussed, and its use in a superposition model highlights the potential of reverse firing (shield blasting) to reduce wall PPM. A conceptual model is also introduced to give a further insight to vibration screening and damage (via ground heave). This model predicts that a centre-lift blast will have a central heave profile and that a reverse-fired shot will produce a smaller power trough than that produced by a standard shot. It is demonstrated that the mechanism of presplit formation is not well understood; nevertheless, experimental evidence shows that presplits can be an effective method for reducing wall vibrations.CITATION:Blair, D P, 2015. Wall control blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 13–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

By G Lumley

PlannersÆ optimism (or maybe commercial necessity) means that most mine plans use equipment rates that are rarely achieved (Lumley and Beckman, 2009). This lack of understanding of what equipment actually moves is causing erroneous equipment forecasts, leading to incorrect mine development plans and economic evaluations. Compounding this problem is a downward trend in actual equipment performance in some areas. Consequently, the presentation of realistic mine plans that are actually achieved in practice is not a common occurrence. However, rational, fact-based mine planning is available to those who want it. Hundreds of millions of cycles of data from open cut mining equipment has been collected from mines around the world since 1992. This unique and highly valuable databank is growing at an exponential rate and is being used by a number of our big miners to support rational and fact-based decision-making. However, neither the use nor the appreciation of the value of this data is universal. There is a challenge to everyone in the mining industry - how do you access value from it? The databank was drilled into and the results analysed for, the Australasian Mining and Metallurgical Operating Practices (AMMOP) publication (Lumley, in press). For this paper the analysis has been extended to include interpretation of trends for draglines, shovels, excavators and trucks. It investigates trends between coal and non-coal mines and across geographic areas. It is known that mining equipment performance in most sections of the industry is falling. This paper attempts to quantify the fall and provide explanations. The trends are analysed to extract the reasons behind the changes and most importantly, what can be done about it.CITATION:Lumley, G, 2012. Understanding trends in performance of open cut mining equipment, in Proceedings Project Evaluation 2012 , pp 203-224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By B Crowdey, J Wall

The particular underground operation relating to this paper is a gold producer and has an orebody predominately consisting of rhyolite and marcasites pyrite. The ore has been identified as being reactive to nitrates.Operations currently utilise two twin boom Tamrock™ Super-Drill Jumbos for development mining. Capital (waste) headings have a nominal size of 7 m wide × 6 m high, while ore headings are designed at 5 m wide × 5 m high, with the lower reaches of the mine narrowing down to a 4.5 m × 5 m design. Production drilling is currently undertaken with an Atlas-Copco L6 Solo. Due to the reactivity of the ore, inhibited emulsion phase bulk explosives are used for all blasting activities, with electronic detonators utilised in the production sequence.Sublevel shrinkage stoping is utilised when the orebody is stronger than the host rock. After blasting the ore, and during extraction, the surrounding host rock cannot maintain integrity and it ‘collapses’ on top of the ore. Gravity forces this collapsing rock to follow the blasted ore through the drawpoints.The highest risk involved with sublevel shrinkage stoping is the necessity for charge crews to work upon ‘rills’ at the drawpoints, which are occasionally unstable, to charge the next blast ring to be fired. To overcome this issue a loading technique called ‘precharging’ is used whereby two to three rings are charged, but only the first ring is fired. This technique can minimise risks by taking the charge crew away from the rill and brow.As this mine contains hot and reactive ground, strict guidelines from the Australian Explosives Industry and Safety Group Inc (AEISG) are adhered to. These guidelines relate to the sleep time for the precharged rings.This paper describes the issues faced with precharging in hot and reactive ground, the monitoring required and the systems and procedures that were put in place to enable a successful outcome.CITATION:Crowdey, B and Wall, J, 2014. Precharging sublevel shrinkage production rings in hot and reactive ground with electronic blasting systems, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 283–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By D Morgan, D Sato, B Lumsden, S Senanayake

Laboratory flotation tests on fresh cyclone overflow samples are a useful tool to troubleshoot and indeed to improve plant performance; however, reproducibility between laboratory flotation test and plant performance is important for interpretation of the laboratory tests and hence their usefulness. Chemical reproducibility can be achieved with the addition of the required reagents; however, reproducing the physics of forces and energy in a 5 L cell compared to a 50 000 L plant cell or a 500 000 L plant cell is not generally studied or discussed. For some tests such as collector evaluation the physics of the flotation process may not be critical, but for some evaluations in the laboratory, it can be important.All flotation plants suffer from losses of valuable <20 µm mineral. Selective mineral aggregation has long been recommended to improve the poor flotation recovery of <20 µm sulfide minerals; however, successfully testing any type of selective sulfide mineral aggregation’s effect on flotation recovery in the laboratory on practical plant samples requires reproducing plant cell physics. The energy input per litre and the forces in a laboratory cell are vastly different to a plant cell. Reproducibility between laboratory and plant tests requires that these differences be minimised. The physics of the laboratory flotation cell is particularly important when fine mineral aggregation tests are carried out.This paper outlines a modified laboratory aggregation and flotation method that closely reproduces plant performance in a laboratory test.CITATION:Sato, D, Lumsden, B, Senanayake, S and Morgan, D, 2014. Development of a laboratory flotation method to test plant mineral aggregation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Incidental to the progress of a geological survey of the Kalgoorlie goldfield during 1927 - 1928 a number of specimens of telluride minerals were obtained, chiefly with the help of Mr F G Brinsden, general manager of the South Kalgoorlie mine, and Mr Ernest Williams, general manager of the Boulder Perseverance mine. This collection was supplemented by a number of small specimens, including the rare copper telluride, which were collected and preserved from the Kalgoorlie mine by Mr A E Paton, and also by a few miscellaneous specimens from the collection of MrS F C Cook, of the Palace Hotel, Kalgoorlie.An extensive knowledge of the rare tellurium-bearing minerals was compiled during the last century from occurrences in Transylvania and Colorado. The recognition of different species has been based on chemical analyses and crystallographic measurements. In a few species there has been an absence of crystalline form, and these, together with the discoveries in this century of rickardite and 'weissite', muthmannite and empressite, have depended chiefly on the chemical analysis for identification. On the other hand, the crystalline form of nagyagite and stiitzite has been described in detail, while their precise chemical formulae were doubtfully defined.The announcement of the occurrence of tellurides at Kalgoorlie by A G Holroyd in the Kalgoorlie Mine on 29 May 1896, followed by their discovery in comparative abundance, stimulated the further study of these minerals. In this locality there is a general absence of well-formed crystals, and the knowledge gained has been confined to the record and description of previously known, but exceedingly rare, species.No new species has been recorded, but the intimate association of various species resulted in early description of two supposedly new species, kalgoorlite and coolgardite. These have been discredited since the investigation by L J Spencer in 1903, based on a collection of specimens donated to the British Museum.Spencer's list of species at Kalgoorlie comprises calaverite, sylvanite (or krennnerite), petzite, coloradoite, 'and altaite, and does not include hessite, previously mentioned by Krusch. In 1912 melonite and a copper telluride were added by J A Thomson and the presence of hessite confirmed. In 1912 there also appeared a full and detailed account by E S Simpson on behalf of the WA Geological Survey, which embraced his earlier notes on the tellurides, and which represents the state of our knowledge of the Kalgoorlie minerals, practically as far as can be attained without the use of the reflecting microscope.The position has been stationary for about 18 years, and it was thought. that the best use to which the present collection of tellurides could be devoted was an attempt by mineragraphic methods to study the mineral relationships, not only of the tellurides among themselves, but also to gold and other associated minerals. The precise mineral content and relationships become a factor of added importance with the development of flotation methods of treatment at Kalgoorlie.Moreover, the study would supplement the description of the ore deposits of the Boulder Belt that has recently been published.

Jan 1, 1994

By J Samosir, L A. Snyman

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant that produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment the ore.An issue affecting production in 2011 was the stability of the E48 mine. A small portion of the drives on the extraction level began to deteriorate as the ground support system failed. The problem was temporarily fixed by stopping production in three extraction drives and tight filling selected areas within these drives (and drawpoints) with low-strength concrete. This action provided immediate support and stability whilst allowing time to investigate potential ground support remedies. From these investigations it was decided to use resin injection technology and additional ground support to stabilise the rock in the aforementioned extraction drives as the concrete plug was excavated in a controlled advance and sequence. This made the area safe and ensured the ongoing safe operation of the E48 mine. The redevelopment of one of these drives began late in 2011, with the remainder being progressively redeveloped over the next two years in order to maintain the extraction level stability.This paper looks at the strategies employed to safely re-open previously converged drawpoints and associated extraction drives that were subject to high abutment loading that was possibly associated with premature cave breakthrough.CITATION:Samosir, J and Snyman, L A, 2014. Redevelopment at Northparkes following significant drive closure, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 87–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By P D. Munro

On the occasion of the 14th Mill Operators’ Conference and marking 40 years since the first one was held in Mount Isa in 1978, it is fitting to review the history of the Conference and its development over that time.The first 10 Conferences were irregularly held at three to four year intervals, with 9 of these in regional centres of Australasia. It is only since 2012 that the Mill Operators’ Conference has become a regular biennial event, alternating with the MetPlant Conference.The number of people attending the Conference has more than doubled to 470 delegates at the 13th one in 2016. It has outgrown its regional beginnings.Papers presented to the previous Conferences have been analysed according to commodity, country of origin, technology and theme plus the affiliation of the authors to discern any trends that may assist in planning the future events.Suggestions are made as to how the AusIMM might wish to arrange its mineral processing/metallurgical conferences.Recent changes to the structure of the Conference providing a more meaningful experience for the delegates and increasing their interaction and involvement should be vigorously pursued.CITATION:Munro, P D, 2018. Mill Operators’ conferences – a 40-year retrospective and a vision for the future, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 5–14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J W. Muir, N Bedford

Hong Kong is one of the most rapidly developing cities in the world. With constant population growth and limited opportunities for space, the development of a fast and effective underground public transportation network is essential. Hong Kong’s Mass Transit Railway (MTR) Corporation is currently undertaking several large underground expansions to its existing network. Much of the excavation will be carried out using the drill and blast excavation method.Drill and blast excavation is common in Hong Kong and with the continued development of underground infrastructure the use of the drill and blast excavation method will increase. Although an effective method of excavation, the blasting vibrations caused during construction can have an adverse impact on surrounding structures and impose disruption on the local community.In order to minimise the risks associated with blasting vibrations, and to demonstrate that the impact on local stakeholders will remain within acceptable limits, it is generally necessary for a contractor to submit a blasting assessment report for approval by government authorities before blasting may commence.Continued increases in population density will force more infrastructure to be constructed underground. Tunnels and caverns are increasingly excavated in closer proximity to critical sensitive receivers. This leads to greater potential impacts on the community, tightening constraints on contractors and a higher level of confidence required for approval authorities. Finding a balance between the needs of the community and rising construction costs becomes more challenging.This paper presents a case study on how the blasting assessment report process has been successfully implemented for a major MTR project situated in a densely developed area of Hong Kong. It describes several methods of assessing blasting vibration impacts, innovative uses of blasting for excavation and the mitigation measures employed to provide the best outcome for all project stakeholders.CITATION:Bedford, N and Muir, J W, 2014. Blasting vibration assessment and innovative blasting methods in high-density urban environments, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 9–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014