Search Documents

By Irving B. Cadoff, Ernest Levine

The fracture path in a Cu-4 pct Ag alloy wet with mercury was found to he dependent on the heat treatment used prior to tensile testing. Both quenched and slow-cooled alloys were embrittled by the mercury.. For quenched alloys, which were single -phase, the crack path was intergranular. Slowly cooled alloys, which contained precipitate platelets, exhibited transgranular fracture. By comparing stress-strain data for these alloys with similar data on mercury -embyittled solid-solution alloys, it was found that the role of the precipitate and that of the grain boundary in the fracture process were equivalent . THE fracture path which results when metals are strained in a liquid environment appears to be dependent upon the nature of the specific system. Mixed transgranular and intergranular cracking has been observed in the 2024 T4 aluminum alloy when wet with a Hg-Zn amalgam.' Transgranular fracture was induced in an A1-4 pct Cu alloy by masking off the grain boundaries from the liquid Hg-Zn amalgam.' The embrittlement of solid-solution alloys of copper in mercury results in intergranular fracture.' The effect of a precipitated phase on the fracture path in copper alloys is the subject of the present investigation. Cu-4 pct Ag was chosen so that its behavior could be compared with previous work on embrittlement of copper alloys. PROCEDURE High-purity copper (99.999 pct) was used as a base metal, along with 99.999 pct purity silver. Melting was carried out in graphite crucibles with manual agitation to get adequate mixing. The ingots were homogenized by means of vacuum annealing, chemically cleaned, and cold-rolled with intermediate vacuum anneals, to the desired thickness of 0.025 in. The rolled sheets were sheared to the final specimen size of 1 by 0.025 by 0.1 in. The specimens were then electropolished in phosphoric acid (concentrated) and heat-treated in an evacuated capsule at the solution temperature of 770°C. One batch was slow-cooled and the other quenched in water. The thermal etching which occurred during heat treatment was sufficient to permit grain boundary and precipitate delineation. Tensile tests were carried out in air and in mercury on a Table-Model Instron at a pulling speed of 0.2 in. per min. Wetting was accomplished by electro-polishing in phosphoric acid, rinsing in alcohol, and immersing in a pool of mercury. Once wet the coating was stable throughout the mechanical tests. In our studies it was found that wetting the surface or total immersion in mercury produced identical results. For convenience, the wetting technique was used for the experiments described. The crack pattern was observed directly on the surface by removing the mercury after testing. De-wetting was accomplished by flame heating the samples in a vacuum after testing and before observation of the surface. No etchant or polishing was used so as not to obscure the crack pattern on the surface. The mercury removal, however, resulted in a pitted surface but otherwise left the pertinent features visible. Photomicrographs were taken in this condition so as not to disturb the structure associated with the crack pattern. The average precipitate spacing was measured previous to coating the sample with mercury by use of an optical eyepiece micrometer. RESULTS The microstructure of the quenched specimens was single-phase while that of the slow-cooled specimens contained thin platelets of a second

Jan 1, 1964

By James P. Kimball

THE object of the present memoir is to put on record some practical experiments by the writer in smelting a silicious native magnetite with no other flux than the silicates of its own gangue: This work was undertaken in the spring of 1878 for Messrs. Naylor & Co., of Boston, to whom I am indebted for the privilege of here communicating its results, these having hitherto only been simply announced.* So far as I am aware these are the first instances of the kind in this country that non-calcareous; or rather non-carbonated, magnetites have successfully been used strictly alone as self-fluxing ores in the blast furnace; that is, without the addition of calcareous flux in the form either of limestone, quicklime, calcareous ore, or basic (calcareous). slag. Previous to the spring of 1878, when the Chateaugay magnetic ore was first brought to my notice, its use had been limited to Catalan forges, after "separation" at the ore bed. The blooms and billets made from it in the several forges of Messrs. Weed & Williams, and of Mr. Williams, were well known in the trade as among the best in the market. The Chateaugay ore beds proving of great magnitude, and the ore exceptionally low in phosphoric acid, it commended itself for blast-furnace purposes to Messrs. Naylor & Co., who employed nee to blow-in the charcoal furnace at Pittsford, Vt., on this ore in the spring of 1878., a previous trial of this ore in the same furnace in the fall of 1877 having proved abortive. This was therefore the first time that Chateaugay ore was successfully smelted in a blast furnace, although since well known as a blast-furnace ore possessing superior and exceptional qualities. The Pittsford furnace, although rebuilt in 1844, and subsequently improved by the former owner, the late J. Prichard, is one of the few furnaces of the old type with open breast (Sumpfofen) still active in this country. Its improvements on furnaces of the period, * Bulletin American Iron and Steel Association, XII, 1878, 132, 156.

Jan 1, 1881

EUGENE COSTE, ? Calgary, Alta.-Evidently in Argentine they have a petroliferous province just east of the Andes where very much the same conditions exist as are found on the east side of the Rocky Mountains and in the plains adjacent. It strikes me, though, that the same mistake is being made in Argentine in the exploration for oil as was made in Alberta, Canada; viz., drilling the wells too .near the seepages in the belt in the eastern part of the petroliferous province, too near the mountains. This same mistake was made in Alberta, with disastrous results; viz., only fissure production was found. The strata so near the mountains are tilted at a very strong angle, such as is described in this paper, and the dislocations are intense. On the other hand, we have found that when we get 100 or 200 mi. away from the mountains we get into oil and gas belts which are very prolific. So far our fields in Alberta have been gas, but in Wyoming, as you know, they get many thousands of barrels a day. I have no doubt that conditions in Argentine are exactly similar but that they have so far kept too near the mountains and that they want to explore the belts farther east to obtain better results.

Jan 4, 1919

By R. S. Busk, E. G. Bobalek

The relation between gases and metals has been a subject of increasingly active investigation during the past years, principally devoted to the study of metal-hydrogen systems. It has been found that hydrogen is soluble in most molten metals to an appreciable extent and somewhat soluble in most solid metals.l,2 In every known case there is a sudden decrease in solubility at the melting point. Thus a freezing mass of metal containing hydrogen in excess of the solid solubility must in some way expel that excess during the freezing process. This leads to internal blowholes, and such effects as pinhole porosity. Gas trapped in metal that is to be fabricated by a working process such as extrusion or rolling may be the cause of blisters. For some cases, notably in copper and iron alloys, the presence of hydrogen can lead to extreme embrittle-ment of the metal. The aluminum-casting industry has long recognized the importance of hydrogen in its techniques. Excess gas in molten aluminum alloys often leads to the formation of "pinhole porosity" in the solid casting.= To prevent this hydrogen pickup it is necessary to avoid overheating the melt and to protect it from such sources of hydrogen as water. In spite of all precautions, it is sometimes necessary to extract hydrogen from the melt just before pouring by bubbling with a gas such as chlorine or nitrogen. Reccntly it has been found that somewhat similar effects are possible with magnesium alloys, in that the presence of hydrogen can induce or aggravate micro-p~rosity.4-6 This paper is primarily concerned with a presentation of some facts concerning the solubility of hydrogen in magnesium and its alloys, with some discussion of the significance of these facts in a practical sense. In any study of gas-metal systems it is important to bear in mind a clear distinction between adsorption on surfaces and absorption within the lattice.' Considerable attention has been directed toward determining whether hydrogen is truly soluble in any solid metal, or whether the gas extracted from a sample was present at surfaces (external and internal) only.7 Most present day evidence supports the idea of true solution in addition to adsorption. A second important factor when dealing with gas solubility is the dependence of such solubility on external pressure. For diatomic gases such as H², solubility in both liquid and solid metals apparently is proportional to the square root of the pressure, indicating a breakdown to a monatomic gas before diffusion into the lattice.= For true equilibrium values of solubility, therefore, the pressure at the the surface must be constant and, preferably, known. Very little has been published concerning the hydrogen-magnesium system. Winterhager has presented the most

Jan 1, 1947

By R. S. Busk, E. G. Bobalek

The relation between gases and metals has been a subject of increasingly active investigation during the past years, principally devoted to the study of metal-hydrogen systems. It has been found that hydrogen is soluble in most molten metals to an appreciable extent and somewhat soluble in most solid metals.l,2 In every known case there is a sudden decrease in solubility at the melting point. Thus a freezing mass of metal containing hydrogen in excess of the solid solubility must in some way expel that excess during the freezing process. This leads to internal blowholes, and such effects as pinhole porosity. Gas trapped in metal that is to be fabricated by a working process such as extrusion or rolling may be the cause of blisters. For some cases, notably in copper and iron alloys, the presence of hydrogen can lead to extreme embrittle-ment of the metal. The aluminum-casting industry has long recognized the importance of hydrogen in its techniques. Excess gas in molten aluminum alloys often leads to the formation of "pinhole porosity" in the solid casting.= To prevent this hydrogen pickup it is necessary to avoid overheating the melt and to protect it from such sources of hydrogen as water. In spite of all precautions, it is sometimes necessary to extract hydrogen from the melt just before pouring by bubbling with a gas such as chlorine or nitrogen. Reccntly it has been found that somewhat similar effects are possible with magnesium alloys, in that the presence of hydrogen can induce or aggravate micro-p~rosity.4-6 This paper is primarily concerned with a presentation of some facts concerning the solubility of hydrogen in magnesium and its alloys, with some discussion of the significance of these facts in a practical sense. In any study of gas-metal systems it is important to bear in mind a clear distinction between adsorption on surfaces and absorption within the lattice.' Considerable attention has been directed toward determining whether hydrogen is truly soluble in any solid metal, or whether the gas extracted from a sample was present at surfaces (external and internal) only.7 Most present day evidence supports the idea of true solution in addition to adsorption. A second important factor when dealing with gas solubility is the dependence of such solubility on external pressure. For diatomic gases such as H², solubility in both liquid and solid metals apparently is proportional to the square root of the pressure, indicating a breakdown to a monatomic gas before diffusion into the lattice.= For true equilibrium values of solubility, therefore, the pressure at the the surface must be constant and, preferably, known. Very little has been published concerning the hydrogen-magnesium system. Winterhager has presented the most

Jan 1, 1947

By R. L. Boyer, F. Morgan, M. Muskat

In the last several years a type of application of the fundamental permeability-saturation relationships has been developed which offers great promise in the interpretation of general reservoir performance.l-' In these developments no attempt is made to solve the detailed flow dynamics in actual oil and gas-producing systems. That problem still remains unsolved. But the permeability-saturation phenomena are incorporated in the analysis of oil-producing reservoirs in a manner such as to reflect the true role they play in controlling the gross reservoir behavior. In particular, they are introduced in such a manner as to determine the gas-oil ratio of the production at any stage of depletion, and, when combined explicitly with the so-called material-balance principles in differential form, one can obtain a differential equation describing completely the average pressure and gas-oil-ratio history of oil-producing reservoirs. While thus far they have been applied directly only to gas-drive reservoirs, they are susceptible of extension to partial water-drive systems, and qualitatively the same principles are of value in the study Of complete water-drive reservoirs. Moreover, in addition to giving a means for computing the variation of the reservoir pressure and gas-oil ratios vs. the cumulative production, they automatically lead to predictions of the gross ultimate recovery under natural depletion—and when properly extended they provide means for predicting the ultimate recovery under gas or water injection. The data required for such applications are the initial fluid distribution in the producing section, the pressure-volume-temperature data on the gas and liquid phases, and the permeability-saturation relationship for the oil-satuiated zone. The former can be obtained with reasonable accuracy by methods that are well established and available throughout the industry. The permeability-saturation data, however, involve techniques that are not at all standardized. In fact, only

Jan 1, 1947

By M. Muskat, R. L. Boyer, F. Morgan

In the last several years a type of application of the fundamental permeability-saturation relationships has been developed which offers great promise in the interpretation of general reservoir performance.l-' In these developments no attempt is made to solve the detailed flow dynamics in actual oil and gas-producing systems. That problem still remains unsolved. But the permeability-saturation phenomena are incorporated in the analysis of oil-producing reservoirs in a manner such as to reflect the true role they play in controlling the gross reservoir behavior. In particular, they are introduced in such a manner as to determine the gas-oil ratio of the production at any stage of depletion, and, when combined explicitly with the so-called material-balance principles in differential form, one can obtain a differential equation describing completely the average pressure and gas-oil-ratio history of oil-producing reservoirs. While thus far they have been applied directly only to gas-drive reservoirs, they are susceptible of extension to partial water-drive systems, and qualitatively the same principles are of value in the study Of complete water-drive reservoirs. Moreover, in addition to giving a means for computing the variation of the reservoir pressure and gas-oil ratios vs. the cumulative production, they automatically lead to predictions of the gross ultimate recovery under natural depletion—and when properly extended they provide means for predicting the ultimate recovery under gas or water injection. The data required for such applications are the initial fluid distribution in the producing section, the pressure-volume-temperature data on the gas and liquid phases, and the permeability-saturation relationship for the oil-satuiated zone. The former can be obtained with reasonable accuracy by methods that are well established and available throughout the industry. The permeability-saturation data, however, involve techniques that are not at all standardized. In fact, only

Jan 1, 1947

By M. G. Gulley

The drilling for and production of crude oil in the Lima-Indiana and Michigan fields were directly and profoundly affected by the severe strain to which the petroleum industry was subjected during the year 1931. Serious and long-continued overproduction in the large flush areas of the western and southwestern fields, coupled with a nationwide decrease in the annual rate of consumption-increase, served to precipitate ‡ This curve is the Mid-Continent price for 38" gravity crude and hence. affords a basis for estlmating the influence of general factors upon the price structure m these fields. a mid-year economic depression which was functionally reflected in every producing area in the United States. A study of the curves of price changes in portions of the central west territory (Fig. 1) will demonstrate this relationship as well as the ensuing upward trend, which developed when pressure was artificially relieved, at least for the time being, in the producing areas in the southwestern states. All field activities in the Lima-Indiana and Michigan territory during 1931 follow the price curve closely: the mid-year depression was evident in drilling activities— both wildcat and within the proved limits of producing fields, in pipe line

Jan 1, 1932

By J. W. Halley, G. L. Plimpton

Because of the two distinct stages in the solidification of rimmed steel, segregation in the rimmed ingot is more complex than that in the killed or semikilled ingot. In the earlier stage, chemical reactions, resulting in evolution of gas and vigorous stirring of the metal, effect a degree of negative segregation unique to rimmed steel. The composition of this zone constitutes the principal quality advantage of this type of steel. In the later stage of solidification, after the evolution of gas has ceased, the segregation follows the general pattern of a more completely deoxidized steel. However, the composition of the liquid remaining after the first solidification stage varies markedly from that of the original melt, some constituents having been partially removed as reaction products while the concentration of others has been intensified by rejection from the metal solidifying in the first zone. The aim, from the standpoint of segregation, in rimmed steel of high quality is to effect a maximum negative segregation in the rim zone without excessive concentration of undesirable elements at the center of the ingot. To achieve this aim, the composition of the melt may be varied and the furnace and pouring practice may be adjusted within certain limits. It is the purpose of this study to discuss segregation in rimmed steel from the standpoint of the mechanisms that produce it and to survey the phases of open-hearth practice that influence those mechanisms. Mechanisms Producing Segregation The mechanisms that determine the degree of segregation in the rimmed ingot are closely interrelated, making it difficult to select the primary factors and to determine a satisfactory order for presenting them. For instance, the question of sulphur segregation is relatively simple, since sulphur is not directly involved in chemical reactions in the ingot; but its concentration in the rim zone is dependent not only on its original analysis in the melt, its segregation coefficient, and the freezing rate, but also on the rate of its removal from the impure film on the solidifying surface. This washing action involves all the factors (such as freezing rate, the carbon-oxygen product, pressure, etc.) that determine the rate of gas evolution and hence the efficiency of film removal. Sulphur distribution between the rim and core is affected by the volumetric ratio between the two zones, and its segregation in the core is a function not only of the freezing rate of the core but also of all the foregoing factors that determine its concentration in the metal when solidification of the core starts. To simplify the presentation, it is proposed to treat the mechanisms affecting segregation independently in this section, reserving a discussion of their over-all effects for the section in which actual segregation data are given. The factors affecting segregation will be treated in the following order: (I) differential solidification, (2) removal of constituents as

Jan 1, 1945

By Y. Oinouye, H. Ries

Of the several interesting physical properties of clay which have claimed the attention of investigators in recent years, none is more important than the behavior of the material when heated to temperatures above those of dehydration. Some of the problems to be solved are: 1. The mineralogical changes that take place in firing. 2. The relation between temperature and change in constitution, shrinkage, porosity, etc. 3. The importance of the time factor, as duration of firing, either in reaching a given temperature, or of exposure to a constant temperature. Mineralogical Changes As a result of fusion, reactions take place between the constituents of a clay, which result in a reorganization of the mass, and the formation of new compounds. Of the new minerals developed, sillimanite is the one usually recorded, and has been referred to by a number of observers.' There appears to be a difference of opinion, however, regarding the temperature at which it is formed. Thus Klein2 notes that sillimanite forms only above 1300" C., while Mellor claims that it can develop below 1200" C., the difference in results being conditioned by the time factor. In Klein's experiments the test pieces were fired in 12 hr., while in Mel-lor's, the temperature rose from 800" to 1180" in 24 hr., and occupied the same time in cooling back to 800".

Jan 1, 1918

By Lewis A. Riley

I desire to submit, for the consideration and information of the members of the Institute, the following data, drawings, and tables, showing what I believe will be interesting information with regard to the diamond drill, and its uses in developing mineral lands. I would first say that the results given have been obtained during the past two years by means of two drilling machines belonging to the Lehigh Valley Coal Company, operating on their coal lands in the Mahanoy, Lehigh, and Wyoming regions. 1st. A tabulated statement, giving location of borings, date, progress, total cost, itemized cost per foot, etc. 2d. Section showing strata bored in Nos. 5 and 10 holes at Mt. Carmel, see Plate VI. 3d. Section showing strata bored in No. 19 hole at Hazleton, see Plate VI. 4th. Photograph and description of drill No. 2. From the first it will be seen that the total number of test-holes bored up to May 1st of this year is 24; 9 of these are in the Mahanoy region, 6 in the Lehigh region, and 10 in the Wyoming region, in all of which cores have been taken for the whole distance. The total distance bored is 9902 feet. The majority of the holes have been put down for the purpose of proving the lower veins of the coal series, and have had to encounter the harder rocks of the coal formation. Much of the distance has been through the lower conglomerates, going in some cases through the coarse egg conglomerate, the foundation of the coal deposit, and to the green sandstone and red shale which underlie it. These lower sandrocks and conglomerates are among the hardest known to geologists, and present a formidable resistance to the exploring drill. This fact must be taken into consideratiotl in comparisons of cost of drilling, and when considered will still further improve the very favorable results I am able to show in my statement of costs. In illustration, I will cite the work of one bit when boring in the upper or softer rocks of the Wyoming region, where 280 feet were obtained without resetting, while in the Lehigh and Mahanoy regions, in the lower and harder rocks, bits set with the same quality of diamonds would only bore from 3 to 20 feet before being worn out. In this connection it may

By Brison Robertson, W. P. Fishel

The carbide-forming tendencies of the various steel-alloying elements, or their affinities for carbon, is a subject that has received considerable attention, but little more than a probable arrangement of the elements as to their carbide-forming tendencies has been proposed. The physical properties of alloy steels depend upon the relative proportions of the elements present and their combinations. one important phase of this subject is the distribution of carbon between the various elements present. The distribution of car. bon between iron and other elements evidently sill depend upon: (I) the affinity of each for carbon; (2) the relative atomic masses of the elements present; and (3) the possible formation of compounds between the alloying and iron and between the elements themselves, In ternary steels the case is simplified, especially in systems in which the element and iron form no compounds, In such systems iron and the alloying element are competing for the carbon present. In this work the distribution of carbon between titanium and iron has been studied by measuring the relative amounts of iron carbide and titanium carbide present ill a series of annealed steels in which the ratio of titanium to carbon extended from 0.527 to 4.61. Ten Fe-Ti-C alloys, weighing about 250 grams each, were prepared by melting under a Vacuum, in an Induction furnace, Armco iron, carbon-free ferrotitanium (25 per cent Ti), and pure carbon. Vacuum melting prevented the formation of titanium oxides and nitrides, which would the the problem. The melts were made in graphite crucibles lined with sintered magnesium oxide. The ingots were the in the furnace under a vacuum and "'ere then completely annealed at 950°C. The determination of the amount of titanium carbide present was based upon the established insolubility of titanium carbide in boiling dilute (1:4) sulphuric acid, and the complete solubility Of free titanium and titanium-iron compounds in this acid. High-carbon ferrotitanium, which had been treated to remove free Ti and Fe. was found to be completely insoluble in the acid; and the carbon-free ferrotitanium used in making the alloys was found to be completely soluble. Others have reported the insolubility of titanium carbide in sulphuric and hydrochloric acids. Turnings from the ingots were digested with boiling sulphuric acid (1:4) until all action had ceased. The carbide residue was filtered off and analyzed for titanium, and in some cases for carbon. This represerifs the titanium that was united with carbon The filtrate from the carbide residue contains the portion Of the titanium that was in solid solution in the ferrite. Titanium

Jan 1, 1945

By J. R. Mihalisin

THE application of electron-microscopic techniques to the study of high-temperature alloys has met with considerable success.' This is due, in part, to the submicroscopic nature of the phases present in this type of alloy making high resolution methods necessary. Among the newer electron-microscopic techniques, the extraction replica technique' has proven to be of great value. This method allows phases to be examined in situ in the microstructure and permits their identification by means of electron diffracticn. This technique eliminates the main disadvantage in using electrolytic extraction of residues as a means of phase identification; that is, the uncertainty of relating constituents identified in the residue to what is observed microscopically. In the course of work relating microstructure to physical properties in high-temperature alloys, it was found that the formation of grain-boundary carbide phases and intragranular precipitation of an age-hardening phase greatly influence strength and ductility at high temperature. In particular, it was found that the formation of a unique type of precipitate in Nimonic "80" (a nickel-chromium-aluminum-titanium type superalloy), termed cellular or discontinuous precipitate, at grain boundaries generally results in poor ductility at high temperature. However, this mode of precipitation can be avoided by proper heat-treatment. It was assumed that this precipitate was either a carbide or age-hardening type of phase. Using various etching procedures with the extraction-replica technique, it was found to be possible to extract the carbide and age-hardening phases preferentially in this type of alloy. Previous work has shown that the age-hardening phase can be extracted from superalloys merely by

Jan 1, 1959

By W. L. Phillips

Single crystals of aluminum, brass, and copper oriented for (100) and (110) slip were extended at 25°, 400°, and 600°C in simple shear. Aluminum specimens oriented for nonoctahedral slip began to shear at a higher critical resolved shear stress than specimens oriented for octahedral slip. Parabolic stress-strain curves were obtained from zero strain. The initial rate of parabolic hardening was lower for specimens sheared on the (100) plane in a close-packed direction <110>, than for specimens sheared in a nonclose-packed direction <100>. metallographic evidence, however, showed that all slip traces could be explained in terms of (111) <100> slip. All attempts to cause nonoctahedral slip in copper and 70-30 a-brass single crystals were unsuccessful. Instead of shearing, the crystals bent, allowing {111} type planes to come into action. NONOCTAHEDRAL slip in aluminum has been reported under three different conditions: first, as the main mode of slip in tension experiments at elevated temperatures;&apos;-&apos; second, as the main mode of slip in direct shear experiments at room temperat~re; and third, as a minor mode of deformation, i.e., as cross-slip, in tension, shear, and bicrystal experiments at room and elevated temperatures."-l2 However, as far as the author knows, nonoctahedral slip has not been reported in either copper or 70-30 a-brass. The present study was undertaken to determine whether nonoctahedral slip could be obtained in aluminum, brass, or copper at room or elevated temperatures when the shear stress was approximately constant over the cross-section, a maximum at the center, or a maximum at the surface. EXPERIMENTAL PROCEDURE A detailed description of the crystal preparation and shearing apparatus has been given previo~sly. Cylindrical crystals 1/2 in. in diam and 8 in. long were grown from the melt in a temperature-gradient furnace. The aluminum contained 0.001 pct Zn, 0.001 pct S, and 0.001 pct Fe; the 70-30 brass contained 0.015 pct Pb, 0.001 pct Fe, 0.01 pct Ni, 0.02 pct Sn, and 0.005 pct Se; the copper was certified OFHC of 99.98 pct purity. All samples were electropolished prior to testing. The shear apparatus was a modified Bausch type. The strain sensitivity was 4 x lob4 Load was applied by clamping the rods attached to the shear plates in an Instron tensile machine. The rate of loading was 0.02 in. per min. In all cases a 1/8-in. gage length was used. For the tests performed at 400° and 600°C the shear plates, collars, and rods were made of stainless steel. These elevated-temperature tests were performed in an argon atmosphere. A) Aluminum at Room Temperature. Values of a and ß for the various slip planes and slip directions investigated are shown in Table I where a is the complement of the angle between the specimen axis and the slip direction, and ß is the angle between the specimen axis and the normal to the shear plane. The shear stress is a function of a (assuming ß - 0);10 when a is less than 27 deg, the shear stress on the slip plane for which the specimen is oriented has a maximum at the center of the crystal; at a = 27 deg the shear stress is constant across the slip plane; for a greater than 27 deg the shear stress is a minimum at the center. Fig. 1 shows the stress-strain curves for specimens cut from crystals 1, 2, and 5, which were sheared on the (010) plane in the [loll direction at room temperature. These three crystals have shear-stress distributions corresponding to the three dif-

Jan 1, 1962

By G. W. Binkley, G. K. Dumbauld, F. A. Brooks, B. E. Morgan

In recent years, oil well cementing compositions have been developed with low densities, controlled set strengths, and satisfactory thickening times. With the introduction of the permanent-type well completion method for cementing wells, another property—that of rate of filtration or water loss to permeable formations— has become important. Laboratory data show that cement slurries prepared with oil, water, bentonite, and calcium lignosulfonate possess satisfactory thickening times, strengths, and filtration properties for primary cementing of casing and for squeeze cementing with the permanent-type well completion technique. Cementing compositions have been prepared with oil-in-water emulsions varying in composition from 60 cc water and 20 cc oil per 100 gm cement to 90 cc water and 45 cc oil per 100 gm cement. These compositions have contained from 0.4 to 5.0 per cent calcium lignosulfonate by weight of dry cement. Slurries prepared from these compositions weigh 11.4 to 13.1 lb/ga1 and have filtration rates of from 10 cc to approximately 100 cc in 30-min API tests at room temperature. The unfiltered emulsion cements develop one-day tensile strengths of 60 to 220 psi; and the filtered mass sets to tensile strengths of 60 to 150 psi in 12 hours and develops strengths of 320 to 515 psi in seven days when cured at 125° F. Field experience gained from 13 field mixing jobs demonstrates the utility of the emulsion cement for permanent-type squeeze cementing operations. INTRODUCTION In recent years, research in oil well cementing composition has been directed toward the development of cements having low densities, controlled set strengths, satisfactory thickening times, and low rates of water loss by filtration. Two well cementing compositions that have been developed with these properties are the modified cements containing, respectively, 12 and 25 per cent bentonite clay and various concentrations of calcium lignosulfonate1,2 In a search for other ways to incorporate these characteristics in a cementing composition, consideration was given to the rheological properties of oil-emulsion drilling fluids. Many of the desirable properties observed in oil-emulsion drilling fluids are equally advantageous in a cementing composition. For example, low water loss by filtration and low density, which are inherent characteristics of these oil-in-water emulsions, are desirable for many oil well cementing operations. Furthermore, oil-emulsion slurries have lubricating properties similar to those of oil-emulsion muds, a factor which should provide ease of rotation of casing during primary cementing operations. The properties of lubrication and low filtration may be of special value in both primary and squeeze cementing operations encountered in slim-hole drilling. Studies in the preparation of oil emulsion systems have pointed out the need for violent agitation in order to disperse the oil into the water phase. It was thought, therefore,

Jan 1, 1957

By J. W. Mitchell

Season cracking of 70-30 cartridge brass cases of small arms and artillery ammunition has been under investigation at the Frankford Arsenal for many years. The nature of this stress-corrosion failure has been found to be intergranular. Much of this work, however, has been directed toward improvements in method of manufacturing the cases so as to reduce the tendency to season crack and little progress had been made toward finding the source of the chemical agent producing the inter- granular corrosion. Ammonia has been shown to produce season cracking in brass and is known to be present in certain atmospheres, particularly industrial, in sufficient concentration to cause cracking. However, in the case of small arms ammunition, the hypothesis that atmospheric ammonia is the cause will not hold, since small arms ammunition is hermetically sealed during storage and yet occasional lots are found to have cracked after 3 to 5 yr. storage. Much of the early study of season cracking in small arms ammunition was done by Nicholas H. Murdza of the Frank- ford Arsenal. In 1936, he suggested that the corrosive agent might be one of the decomposition products of smokeless powder and mentioned nitrogen oxides specifically. Then in 1937, Murdza suggested that the breakdown of smokeless powder in storage resulted in the formation not only of nitrogen oxides but also ammonia

Jan 1, 1945

By Willard S. Morse

In my paper on "The Lixiviation of Silver-Ores by the Russell Process at Aspen, Colorado" (page 137 of the present volume), attention was called to the decrease in "chlorination " during the washing of the roasted ore with water, to remove soluble salts, before leaching with hyposulphite and Russell solutions. This decrease in " chlorination," which is due to conversion of the silver chloride to some other form not soluble in hyposulphite solutions, and which, for the sake of brevity, will be termed the "going-back" of chlorination, has been a serious obstacle to the successful operation of several leaching-works, and was at Aspen the only difficulty encountered. I have never seen any explanation of the cause of this failure to extract, in actual practice in the mill, the amount of silver chloride shown by laboratory-leachings to be present in the roasted ore; and the purpose of this paper is to record the conclusions arrived at concerning the cause of the phenomenon, and the data upon which they are based. The average decrease in chlorination by washing with water in the Aspen ores for a period of fourteen months was as follows:

Jan 1, 1896

By J. H. Scaff, H. C. Theurer, E. E. Schumacher

The microwave region of the radio spectrum was effectively utilized in radar designs during the recent war and it has become of increasing interest in the field of communications. Work in this field has led to an important use for silicon—that of the point contact rectifiers†1 in the frequency converter of microwave (radar or radio) receivers—and has stimulated considerable interest in the electrical properties and preparation of silicon and its alloys. Silicon is an electronic semiconductor. Its conductivity at room temperature results principally from the presence of certain impurities. While for metals an increase in impurity content increases the resistivity, for semiconductors such as silicon the opposite occurs and, in general, the addition of impurities lowers the resistivity. Silicon materials may be classified into one of two groups depending upon the manner in which the impurities contribute to electrical properties. These have been termed for convenience p-type or n-type. P-type silicon develops a very large positive thermal emf against metals, has a Hall coefficient of positive sign and a low resistance direction in point contact rectification with the silicon positive with respect to the point. N-type silicon, on the other hand, develops a negative thermal emf against metals, has a Hall coefficient of negative sign and a low resistance direction in rectification with the silicon negative with respect to the point. Impurities which produce n-type silicon are called donors inasmuch as these elements contribute to electrical conductivity by donating electrons to an unfilled energy band in the silicon. On the other hand, elements which produce p-type silicon are known as acceptors as these impurities contribute to the electrical conductivity by accepting electrons from a filled energy band permitting what is known as conductivity by "holes" in which the sign of the carriers appears to be positive. A general treatment of the mechanism of conduction in semiconductors from the viewpoint of modern band theory has been given recently by Pearson,2 by Becker, Green and Pearson,3 and by Torrey and Whitmer.4 In this investigation boron and aluminum have been found to be acceptors, and phosphorus, arsenic, and antimony to be donors in silicon. Data on the effect of boron and phosphorus on the electrical properties, when present singly and in combination, have been acquired. These data are discussed in the present paper. Raw Materials Used and Methods for Adding Seeond Constituents Silicon from two sources was used in this work and these will be referred to as A and B respectively. Silicon A is a material of high purity supplied by the Electro Metallurgical Co. It is prepared by chemical purification of "commercial" silicon obtained from the arc furnace reduction of SiO2. It contains 99.8 pct silicon, minimum, with small amounts of calcium, iron, aluminum, boron, and phosphorus as the principal impurities. This material was extensively employed in these studies as well as in the commercial preparation of rectifier materials. Silicon B is a material of high purity from the du-Pont Co. It is prepared by a pyrolytic reduction of Sicl4 and is free of analytically detectable amounts of boron and phosphorus. Its use permitted study of the effect of boron and phosphorus individually on the properties. This material contains, however, spec-troscopic traees of a number of metals, some of which affect electrical and rectification properties. Typical analyses for the two grades of silicon are given in Table 1. To make controlled additions of boron to the charge it was necessary to employ a low boron content master alloy since the quantity of boron to be added was usually only a few thousandths of one percent. The alloy containing nominally one percent boron was prepared by melting chemically pure boron with silicon A using the melting techniques for 320 g silicon

Jan 1, 1950

By Joseph G. Debanné

Foreword The three case histories and the liquid fuels planning scenario presented in this paper span a twenty year period, from the pioneering days of computers in the petroleum producing industry during the mid-fifties, to the energy crisis era of the seventies. Inasmuch as two of the main actors, Ian McKinnon and I, are featured in all three case histories, while I am currently involved in the fossil fuels scenario, this paper provides four related and personal spot readings along an evolutionary path: from the one dimensional technical domain to the multi-dimensional techno-socio-economic domain of computer applications in the petroleum industry. Coincident with this evolution in the direction of increasingly comprehensive and powerful computer applications, the evolution in hardware/software capability and in analytical power are also kept in perspective. The three case histories are: 1. The Bonnie Glen-Wizard Lake Case (Calgary, Alberta, 1955-1957); 2. The TransCanada-Great Lakes Gas Transmission Case (Ottawa-Washington, 1966); 3. The Westcoast Transmission - El Paso Pipelines Gas Export/ Import Case (Ottawa-Vancouver-Washington, 1966-1967). The liquid fuels planning scenario is a demonstration exercise rather than a case history; however, it represents an important point on the evolutionary curve and, provides a concrete example of tech-

Jan 1, 1977

By Wolfgang Pitsch

INVESTIGATIONS on the above topic have recently been published by Shapiro and Kraussl and Jana and wayman in this journal and by Kessler and Pitsch.- Parts of the results in these papers are in good agreement with each other but there are also some results which are substantially different. The main points of these differences shall be briefly discussed in this communication. Shapiro and Krauss&apos; measured single-surface traces of the habit planes of reversed austenite plates formed within the martensite crystals and deduced from these measurements two distinct habit planes A = (0.174; 0.309; 0.935) and B = (0.375; 0.545; 0.749) within 3 deg. Kessler and pitsch4 found instead by two-surface analysis7 one habit plane n = {0.23; 0.62: 0.75) with a real scatter of 6 deg. The latter observation of a single habit plane apart from a certain scatter is in agreement with most of the investigations of martensite transformations. The differences between these two results are so great that they cannot be explained by experimental error. The purpose of this communication is to show that the A- and B-poles of Shapiro and Krauss are due to an erroneous interpretation of a single-surface trace analysis. The difficulties in the interpretation of such single-surface trace analyses are due to the high symmetry of cubic lattices, from which it follows that there are in general twenty-four equivalent possibilities of plotting a single-surface trace in a pole figure. All these possibilities must be taken into account, when putting different traces from different plates together in order to construct the habit plane. Alternatively the poles of all the traces may be plotted in a unit triangle. This is done in Fig. 1 with twenty-nine traces of different reversed austenite plates, all of this were measured by Shapiro and Krauss in the same plane of a single martensite ther traces taken from Fig. 13 in the Shapiro and Krauss paper&apos; which were determined by electron diffraction. The traces in Figs. 1 and 2 have to be compared with the habits A, B, and n which are under discussion. Therefore the great circles of the poles A, B, and n are plotted in Figs. 3, 4, and 5 together with a 3-deg scatter region for poles A, B and a 6-deg scatter region for pole n. Comparing Figs. 1 and 2 with Figs. 3, 4, and 5 one finds the statements which

Jan 1, 1969