Search Documents

By J. H. Faulk

An examination is made of the various factors influencing drilling rate and drill bit life in various diameter holes. It is concluded that drill bits in the size range 4% to 6 1/4 in. can be used to attain substantially the some daily drilling progress as conventional size bits in soft rock drilling operations. An examination of the most important factors influencing "hazard of losing the hole" in the different hole size results in the conclusion that the smaller hole sizes can probably be drilled at reasonably low risk. However, this risk will be somewhat greater in the smaller diameter holes, requiring that special drilling and mud engineering practices be used to make small diameter holes practicable in soft rock drilling operations. An engineering analysia is made of the power and hydraulic requirements of several drill string-hole combinations to test the feasibility of drilling .small diameter holes in soft rock areas. Large econormies in rig power requirements appear possible by drilling .smaller .size holes in these operations. INTRODUCTION The industry now is re-examining the utility of small diameter holes in the light of substantial technical advances made in recent years. Faced with increasing cost of finding reserves and with proration after developing them, the industry must either develop methods of economizing or receive a lower rate of return on investments. Small diameter holes appear to involve an attractive method of economizing. Our objective is to determine if this is technically possible in soft rock operations. Soft rock, as used in this report, refers to those formations of a "drill-ability" corresponding to that of all Gulf Coast formations shallower than and frequently including much of the Eocene rock system. An important phase of technology which we shall examine is relative drilling rate and bit footage which may be obtained with various size bits. Rig operating efficiency, particularly as influenced by hazard, is also discussed in detail. The technical conclusions resulting from these examinations are used to develop sample drill string design and rig horsepower requirements for drilling holes as smaH as 4 3/4 in. and larger. The principal criterion used for the drill string design is that approximately the same daily drilling progress would be possible in all size holes in soft rock operations. This facilitates a comparison of rig size required for drilling the hole sizes in the range between 4 3/4 and 8 3/4 in. BROAD PROBLEM OF DRILLING RATE AND BIT FOOTAGE The three factors controlling daily drilling progress are: (1) drilling rate of bit while on bottom turning, (2) bit footage, and (3) rig operating efficiency. Let us look now at the first two of these factors. Drilling technology has progressed to the point that a semi-quantitative analysis of the effect of various operating variables upon these factors can be made. Those factors which apparently limit both drilling rate and bit footage for bits now in use are: (1) bit design, (2) weight on bit, (3) hydraulic cleaning capacity for bit cutting surfaces and hole bottom, and (4) rotary speed. (We neglect the effect of mud and formation properties because these factors arc the same for the various size bits.

Jan 1, 1957

The first mention of the mining and use of coal in the Pittsburgh district refers to the mine under Duquesne Heights that furnished coal for the garrison at the fort at Pittsburgh in 1760. Coal had been dug and used as fuel just outside of Brownsville, Fayette county, in 1759, but this was not a regular mine as the opening was in an outcropping. Maps of Ohio in 1770 showed "Cole Mines" at various points. The Penns purchased all the coal south of Kittanning in southwestern Pennsylvania from the Chiefs of the Six Nations for a reported price of $10,000. During the Revolution, coal from Herron Hill, Mincrsville, and Coal Hill, all within the present city limits, was used in Pittsburgh. There is today one custom pit opened in Coal Hill (Duquesne Heights). The first steam engine was set up in Pittsburgh in 1794 and used coal as fuel. The first mine in the Youghiogheny gas district was opened in 1796. In 1803, the first shipment of coal by water was made from Pittsburgh down the Ohio river and landed at Philadelphia, where it sold for approximately $9.50 per ton. The mines along the Monongahela were naturally the first to be opened. With the completion of locks and dams in 1844, permitting slack-water navigation, the industry began to thrive. The No. 8 field of Ohio and the Fairmont region of northern West Virginia were opened in the period 1840 to 1855. From that time on there has been a continuous development of the coal rcsources of this district, until at present productive capacity is enough to supply 30 per cent. of the country's needs of bituminous coal. The original method of working the Pittsburgh seam was to drive under cover at some easily accessible point on the outcrop with a single entry, usually 1½ yd. wide. Rooms or gangways were turned to the right and left from this entry and ventilation was usually poor and inade-

Jan 1, 1927

By M. I. Jacobson, M. L. Hammond

The solid solubilities of high-purity silver, aluminum, chromium, copper, and iron in zone-refined beryllium have been determined. Diffusion couple sandwiches of beryllium with aluminum, copper, and silver foil and diffusion couples of beryllium with two-phase alloys in the Be-Cr. Be-Fe, and Be-Ag systems were analyzed by electron beam micro-probe techniques. This paper describes the material used, the experimental methods for preparing the diffusion couples and the alloys, the analytical techniques, and the results obtained. The results are compared with those of previous investigators who used materials of lower purity. ~NVESTIGATORS of beryllium phase diagrams have often been hampered in their interpretations of certain phase boundaries because of the relatively low purity of the beryllium used. This has sometimes resulted in the appearance of three phases in the regions where only two should exist. Advances in purification methods, specifically zone refining, have made available beryllium that is considerably purer than the material previously used for phase diagram studies. The primary object of this investigation was to reex-amine portions of the beryllium-rich end of the binary systems of beryllium with silver, aluminum, chromium, copper, and iron to determine more accurately the limits of terminal solid solubility. The five elements—silver, aluminum, chromium, copper, and iron—include some which are commonly found as the major impurities in beryllium, some of which are being used as solid-solution alloying elements, and some of which are used in ductile matrix alloys. They are thus of considerable importance to physical metallurgists who must work with beryllium but who must rely on the present inaccurate or incomplete diagrams. The determination of more reliable diagrams would aid researchers concerned with the problems of alloying, heat treatment, and ductility. MATERIAL The beryllium was acquired from the Franklin Institute in the form of a single-crystal, 6 in. long by 1 in. in diam, zone-refined in three passes from Pechiney SR-grade beryllium bar. The principal impurities, as determined by mass spectrography at Battelle Memorial Institute, are shown in Table I. Vacuum-melted copper, silver, and aluminum, and electron-beam zone-refined iron were obtained from the Materials Research Corp. in the form of 1/2-in.- diam bars. Iodide chromium was obtained as flakes from the Chromalloy Corp. Analyses supplied with these metals are shown in Table 11. EXPERIMENTAL PROCEDURE Preparation of Diffusion Couples. Two types of dif-fusion couples were used in this study. For the copper, silver, and aluminum systems, the couples were sand-

Jan 1, 1969

By J. F. Butler

The degree and type of carbide dispersion resulting from changes in the cooling rate from austenite determine the amount of carbon remaining in solution after slow cooling- from a subsequent subcritical annealing treatment. A difjusion model has been proposecl to explain the effect of carbide dispersion on the amount of carbon retained in solution and the amount of carbon in solution has been related to the degree of carbon strain aging. COTTRELL and Leak' have shown that the rate of strain aging in low-carbon steels is dependent upon the amount of carbon and nitrogen in solution. Carbon can be effectively removed from solution as Fe , C by quench aging at temperatures of 200" C or lower; however, the relatively higher solubility of nitrogen at these temperatures prevents sufficient removal of nitrogen as iron nitrides. For this reason, nitrogen in solution has been considered the major cause of strain aging in rimming grades of commercial low-carbon steels. Nitrogen can be effectively removed from solution and nonaging steel produced through the addition of aluminum to form the stable nitride, AlN; however, the aluminum also causes deoxidation resulting in a killed steel. III an attempt to produce a rimmed steel which was also nonaging, Morgan and Shyne 2 investigated tile strain-aging properties of low-carban steels containing boron and found that strain aging was suplx-essed in steels containing as little as 0.007 pet B. The original purpose of this investigation was to determine the mechanism of strain-aging suppression by boron. Early in the study, the function of boron was discovered to be much like that of aluminum in that the formation of a nitride, BN, removed the nitrogen from solution.' However, during the course of the investigation, an effect of heat treatment upon the strain-aging properties and the amount of carbon in solution was found which could be related to the microstructure of the steel. The purpose of this paper is to examine these relationships among heat treatment, microstructure, carbon in solution, and strain aging in steels where nondetectable amounts of nitrogen are present in solution. EXPERIMENTAL PROCEDURE The investigation was carried out using 0.030 in. by 12. in wire specimens which had been cold swaged and drawn to the final diameter. Table I lists the compositions of the low-carbon steels used. Those with 'V' designations were vacuum melted and cast; the alloys designated 'AISI' were prepared from high-purity iron obtained from the American

Jan 1, 1962

By Floyd C. Kelly

A. HUltgren, .Söderfors, Sweden (written discussion*).—From the results obtained in his own experiments as well as those of Austin and of Grube Mr. Kelley derives a general law, expressed tentatively in the following words: "whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, a comparatively rapid, or abnormal, grain growth results." It is suggested that,, in order adequately to represent the facts, this definition should he restricted by the following qualifications: a and b are the two metals, b diffusing into a. A. At the temperature in question a should exist as phase a 1 having a limited solubility for b. B. The supply of b by diffusion should be sufficient, in view of the rate of diffusion into a 1, to increase the concentration of b above the saturation value in a 1 so as to cause a new phase a2 to form. (7. The phase a2 should have a range of solubility for 6, thus rendering continued diffusion possible. D. In order that the columnar grains may be preserved in the structure the phase a2 should, of course, not suffer transformation on cooling. The phenomenon thus defined may be described as progressive transformation by diffusion. Its mechanism would appear to he as follows: Fig. 17 shows a portion of the equilibrium diagram a-b, Fig. 18 the distribution of b in solution after various periods of diffusion, Fig. 19 represents the structure in cross-section of a cylindrical rod of a at the end of heating period 3. 1. The first effect of diffusion of b into a will be to establish a concentration gradient in phase a1 (1, Fig. 18). When the saturation value for the temperature of the experiment (m, Fig. 17) is reached at the surface, nuclei of, a2 of composition n will form here, and later develop into a continuous layer. Assuming that diffusion proceeds without irregularities and that transformation at any point sets in without lag—i. e., in the moment saturation is exceeded—the transformation a1-a2 will advance inwards on a cylindrical surface concentric with the surface of the rod. The discontinuity of composition at the transformation surface in the position it happens to have at the end of the treatment (3, Fig. 18) will be preserved at room temperature, if the cooling is not particularly slow, and be recorded in the structure as a marked, smooth line, in agreement with Grube's and the author's observations. The shape of the distribution curves in Fig. 18 is also corroborated by the analyses given by Grube. 2. During diffusion, since the secondary phase a2 is always in immediate contact with the saturated part of the primary phase a1, there should be very little lag in the transformation. This means that the first a2 grains formed should grow in preference to the formation of independent nuclei; in other words, columnar growth results. It does not seem necessary to assume, with Green,' whose conception of the phenomenon

Jan 1, 1929

By Floyd C. Kelly

A. HUltgren, .Söderfors, Sweden (written discussion*).—From the results obtained in his own experiments as well as those of Austin and of Grube Mr. Kelley derives a general law, expressed tentatively in the following words: "whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, a comparatively rapid, or abnormal, grain growth results." It is suggested that,, in order adequately to represent the facts, this definition should he restricted by the following qualifications: a and b are the two metals, b diffusing into a. A. At the temperature in question a should exist as phase a 1 having a limited solubility for b. B. The supply of b by diffusion should be sufficient, in view of the rate of diffusion into a 1, to increase the concentration of b above the saturation value in a 1 so as to cause a new phase a2 to form. (7. The phase a2 should have a range of solubility for 6, thus rendering continued diffusion possible. D. In order that the columnar grains may be preserved in the structure the phase a2 should, of course, not suffer transformation on cooling. The phenomenon thus defined may be described as progressive transformation by diffusion. Its mechanism would appear to he as follows: Fig. 17 shows a portion of the equilibrium diagram a-b, Fig. 18 the distribution of b in solution after various periods of diffusion, Fig. 19 represents the structure in cross-section of a cylindrical rod of a at the end of heating period 3. 1. The first effect of diffusion of b into a will be to establish a concentration gradient in phase a1 (1, Fig. 18). When the saturation value for the temperature of the experiment (m, Fig. 17) is reached at the surface, nuclei of, a2 of composition n will form here, and later develop into a continuous layer. Assuming that diffusion proceeds without irregularities and that transformation at any point sets in without lag—i. e., in the moment saturation is exceeded—the transformation a1-a2 will advance inwards on a cylindrical surface concentric with the surface of the rod. The discontinuity of composition at the transformation surface in the position it happens to have at the end of the treatment (3, Fig. 18) will be preserved at room temperature, if the cooling is not particularly slow, and be recorded in the structure as a marked, smooth line, in agreement with Grube's and the author's observations. The shape of the distribution curves in Fig. 18 is also corroborated by the analyses given by Grube. 2. During diffusion, since the secondary phase a2 is always in immediate contact with the saturated part of the primary phase a1, there should be very little lag in the transformation. This means that the first a2 grains formed should grow in preference to the formation of independent nuclei; in other words, columnar growth results. It does not seem necessary to assume, with Green,' whose conception of the phenomenon

Jan 1, 1929

By E. Marburg

Most ingots complete solidification vertically rather than transversely. This conclusion is based on complete solidification patterns of big-end-up and big-end-down ingots developed from dumped and split ingots. New mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon adequate width of vertical core. A LTHOUGH it has long been recognized that the A internal soundness of ingots is principally been recognizedthatthedependent on the process of solidification, knowledge of this process is still only fragmentary. The mechanisms causing the several types of segregation in ingots, which mechanisms are necessarily related to the solidification process, are not well understood. In absence of a better conception of the solidification process, it seems hardly surprising that mold design varies widely. Guiding principles for mold design are needed. At stake in the improvement of ingot quality are not only improved properties of steel but also appreciably higher yields of sound steel, which would considerably decrease manufacturing costs. In the present study, following a general description of the several types of segregation in ingots, Fig. 1, complete solidification patterns of a big-endup and a big-end-down ingot, including the zones of accelerated solidification, have been reconstructed. In both ingots, a core of vertical solidification extends from the base cone to the hot-top junction. Based on the finding that ingots complete solidification vertically rather than transversely, as has been previously assumed, new mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon the width of the vertical core, which in turn depends principally upon the width to height (w/h) ratio of the ingot. Solidification patterns of ingots are of three general types: 1—those in which vertical solidification does not reach the top, 2—those in which vertical solidification just reaches the top of the ingot, and 3—those in which vertical solidification reaches the top some time before transverse solidification would reach the middle of the ingot, so that a vertical core of definite width at the top of the ingot is developed. Axial defects vary characteristically with the solidification pattern. Examples of ingots of each type are presented. Dumped ingot data reported by Nelson' have been used in developing families of curves of transverse and vertical solidification, and in deriving the effect of the w/h ratio upon the solidification pattern. Photographs of many ingots split at Homestead and at Duquesne Works, United States Steel CO., as well as those published by the British Iron and Steel Institute,' have been studied and analyzed. In the interest of brevity, only typical ingots of each type or classification from the above sources have been reproduced. Segregation in Ingots Segregation in ingots falls into three principal classifications: 1—lamellar segregation, as revealed in sulphur prints (Figs. 2 and 3); 2—zone segregation, or broad variations in composition; and 3— interdendritic, or microsegregation. The last class, of minor importance, is not considered here. When liquid metal cools, according to the theory of differential or selective solidification,2 metal of relatively high purity selectively solidifies first. Liquid segregates (principally carbon, phosphorus,

Jan 1, 1954

By David K. Hylbert

This study investigated roof falls in room-and-pillar drift coal mines in eastern Kentucky and utilized geologic methods for Predicting roof conditions in advance of mining. In the Highsplint mine, the roof was classified in four categories or conditions: Condition A and B (Laminated Shale); Condition C (Rolling Sandstone with Shale in Pockets); and Condition D (Zone of Major Sandstone Roll(s)). Structure contour and isopach maps of the Darby coal bed and associated immediate roof rocks were used to project axial trends of the sandstone roof. Trend mapping in the mine and on outcrop provided more detailed control for roof projections.

Jan 1, 1979

By R. W. Brauchli

The author has made a statistical analysis of the relations between recovery and length of cores, diameters of cores and of drill pipe, and cost of coring under different contractual conditions. The data are presented in tabular form. The length of the core appears to play a minor part in the percentage recovered, with a tendency to lower percentages with increased core length; approximately 50 per cent of the length cored is normally recovered if the cores are more than 2 in. in diameter. The diarneter of the core has a more pronounced influence on the recovery; 1 3/8-in. cores average 29.1 per cent, 2 1/8 -in. core 53.4 per cent and 3 1/8-in. cores with 6 5/8-in. drill pipe 68.5 per cent. Where 31/8-in cores were taken with smaller diameter drill pipe, i. e., 4 1/2 - in. drill pipe in 8 1/4-in. hole, the recovery dropped to 49.8 per cent, indicating that the more rigid drill pipe favors good core recovery, a conclusion also borne out by the results obtained in using large drill pipe for smaller diame-ter cores. Surprisingly good recoveries were obtained from both the Johnson and Simpson sands; shale, limestone and dolomite each gave less then average recoveries. No serious fishing jobs resulted from coring operations. Attention is called to the need of a core drill which will make it possible to drill a full-sized hole while coring, and thus reduce the cost of cores. Data pertaining to core drilling should be consistently recorded, such as, diameter of drill pipe and collar, diameter of core, recovery, size of cutter heads, type of core-barrel, coring time, speeds of rotation and of pumps, weight on core-barrel, etc.

Jan 1, 1933

By Alexandre Pourcel

The phenomena of liquation in steel or iron ingots of all sizes, but naturally to greatest extent in the heaviest ingots, have been noticed ever since the commencement on a large scale of the Besse mer and open-hearth manufactures; but they have been studied with care during the last few years only. The English and the Ameri cans were the first to publish the results of investigation upon phe nomena of this clam, to which they have given the name of segregation. Historical. Passing by that which has been written concerning the segregation observed in gray pig-iron, of which instances were given by Karsten, we shall confine ourselves here to that which is known of this subject with exclusive reference to ingot steel and iron. Mr. H. M. Howe, of Boston, in his Metallurgy of Steel, the most complete and well-arranged treatise upon steel, gives a resume of observations, with the results of numerous analyses, bearing upon the phenomena of segregation. According to Tchernoff (with whom we discussed this question at length in 1878, in connection with the cast-steel plates of large dimensions designed for the Italian fleet, which we showed him at Terre-Noire), Kalakoutsky called attention in 1866 to the lack of homogeneity in Bessemer ingots, especially when cast in sand. Our own attention had been called to the phenomena of liquation in 1868 by a somewhat surprising fact which appeared in almost every one of a number of steel-rail ingots coming from the works of Messrs. Pierre and Emile Martin at Sireuil, to be rolled at TerreNoire. In the heating or in the first groove of the rolls, a slice of from 6 to 10 centimeters (2.4 to 3.9 inches) separated itself from the head of each ingot. As a general consequence, the section of

Jan 1, 1894

By J. B. Cohen, B. W. Howlett, M. B. Bever

The partial molar heats of solution at infinite dilution in tin of aluminum at 300° and 350°C and of gallium, indium, and thallium at 240°, 300°, and 350°C have been measured by tin solution calori-metry. Aluminum, gallium, and thallium are endo-thermic on solution; indium is exothermic. Any temperature dependence of the heats of solution lies within the experimental scatter. Over the dilute ranges investigated, only aluminum has a measurable change in its heat of solution with composition. HEATS of solution of one element in another reflect the interaction between them. The investigation of partial molar heats of solution in dilute alloys is of particular interest as the properties of the solvent are altered to only a limited extent by the presence of the solute and also as the interaction between solute atoms is small. When the heats of solution of a related series of elements in a solvent are known, a systematic comparison may be made. In the investigation reported here, the partial molar heats of solution of the Group III elements aluminum, gallium, indium, and thallium in dilute solution in tin were measured. This work follows an investigation of the heats of solution in tin of the Group IB elements.' EXPERIMENTAL PROCEDURES Materials. Samples of gallium, indium, and thallium were obtained from Johnson, Mathey and Co., Ltd. Indium and thallium were supplied as wire, 1.6 mm in diam; gallium was in the form of irregular pieces. The supplier reported the following minimum purities: gallium—99.95 pct; indium—99.99 pct; thallium—99.99 pct. The aluminum, obtained from Alcoa Research Laboratories, was reported to be 99.995 pct pure. The tin was supplied by Baker and Co., Inc.; the reported analysis indicated a tin content of at least 99.96 pct with lead as principal impurity. Calorimeter. this description will cover only the essential features of the calorimeter with special attention to modifications made since an earlier description was published.' A Dewar flask containing the tin bath was held in a constant-temperature bath of a near-eutectic mixture of lithium, sodium, and potassium nitrates. This bath, which was stirred vigorously, was heated by a primary resistance winding in the container wall and by a secondary winding immersed in the salt. The voltage supplied to both windings was stabilized. The temperature of the salt bath was controlled by means of a platinum resistance thermometer in one arm of a Wheatstone bridge. The light from a mirror galvanometer in the bridge circuit fell on a photocell which controlled the current in a saturable reactor in series with the secondary winding. In this manner, the temperature of the salt bath was controlled to ±0.003°C and that of the tin bath to at least ±0.002°C. Each of these temperatures was measured by two iron-constantan thermocouples in series, coiled in a helix to minimize heat loss and immersed in the salt and tin baths in protective sheaths. The temperature of the laboratory was kept constant to ± 1°C during a run. Specimens were dropped into the tin bath from an addition arm held at O°C which was part of the cal-orimetric system. The system was evacuated to about 0.02 1 to minimize oxidation and to reduce transfer of heat. The bath was stirred by a glass stirrer introduced through a double Wilson seal. The samples were scraped clean before weighing, which was carried out as rapidly as possible. Each sample was immediately placed in the evacuated addition arm to minimize contamination. These precautions were especially necessary with aluminum. After the runs with gallium and thallium at all temperatures and with indium at 240° and 350°C (Series I) were completed and before the runs with indium at 300°C and aluminum at 300° and 350°C (Series 11) were begun the following changes were made. The shape of the Dewar flask was changed so as to result in a lower surface to volume ratio of the bath and at the same time the amount of tin was reduced from 500 to 400 g. The paddle type stirrer was replaced by a helical screw and the rate of stirring was increased to about 150 to 200 rpm.

Jan 1, 1962

By Douglas R. Cook

The discovery of the gold deposits of the Jerritt Canyon district, with proven recoverable reserves in excess of 67.6 Mg (2.4 million oz) of gold, has contributed greatly to the tremendous resurgence in exploration for disseminated gold deposits in Nevada and throughout the west. The Jerritt Canyon project, including the Bell mine, is a 70130 joint venture between Freeport Gold Co. and FMC Gold Corp., both of which are wholly owned affiliates of the respective parent companies, Freeport-McMoRan Inc. and FMC Corp. The Jerritt Canyon district is located in the center of the Independence Mountains in north-central Elko County, Nevada, approximately 48 km (30 miles) northeast of the Carlin gold mine and 68 km (42 miles) north of Elko. Although the discovery of a commercial gold mine at Jerritt resulted from Freeport's exploration activities, the initial identification of a gold prospect in this area was a consequence of a program by FMC in the search for antimony. Their program was, in part, based on data in the Nevada Bureau of Mines Bulletin 61, "Antimony Deposits in Nevada." Work on the property began in 197 1 with geologic mapping followed by sampling and geochemical analyses. FMC geologists, including Robert Hawkins, Russell Hayden, and Hal Hurst recognized the striking similarity of the area to the geologic environment of Newmont's nearby Carlin gold deposit and soon focused on the gold potential. Increases in the price of gold served to stimulate interest and support for the exploration program. Geochemical samples were collected and analyzed for gold and trace elements usually associated with gold. A strong gold anomaly was found on the North Fork of Jerritt Canyon, which was called the Alchem anomaly. Drill-testing of this anomaly in 1973 revealed significant grades and thicknesses of gold mineralization in the lower portion of the Roberts Mountain formation. This initial discovery and subsequent close-spaced drilling proved the existence of several small pods of low-grade, gold-bearing material which cropped out at their up-dip edges, causing the surface anomaly. The mineralization was very encouraging, but was not, by itself, of economic importance from the standpoint of either grade or tonnage. Freeport Exploration Co. established a district office in Reno in late 1974 with responsibilities for exploration of hard minerals in the Basin and Range Province. Emphasis of the program was directed to the discovery of precious metal deposits. Enfield Bell, as District Manager for this new office, was particularly interested in the Independence Mountains and when the opportunity for a joint venture with FMC became available in 1976, it was aggressively pursued. Enfield Bell and David Stevens evaluated the FMC data and with the support of management formulated a bid in competition with 23 other companies. Freeport was selected by FMC as partner and a joint venture agreement was successfully negotiated. In mid-summer of 1976, Freeport Exploration Co. began an expanded program of detailed mapping and geochemical sampling under the direction of Bell and Stevens that led to new interpretations of the structural and alteration patterns. Hawkins' contribution during this period must be recognized since he not only was one of the original geologists assigned to the antimony and subsequently the gold investigations, but shortly after the start of the joint venture exploration, he was hired by Freeport Exploration Co. as the project geologist for the venture. Hawkins had studied the central Independence Mountains for his thesis and his understanding of the regional geology provided an excellent background for the continued exploration of the gold de- posits. His interpretation of the structure in the vicinity of the Alchem anomaly was of significant help in the Freeport exploration program. Drilling, based on this new under- standing of the geology, revealed the edge of the Marlboro Canyon ore body, which is now being exploited in the Bell mine. Although a classic bullseye geochemical target led to the discovery of the Alchem mineralization, the bulk of the reserves known today in the Marlboro Canyon area lay

Jan 1, 1985

By Elwood G. Haney, R. N. Parkins

Stress corrosion cracking of two heats of 18 pct Ni maraging steel in rod form immersed in an aqueous solution of 0.6N NaCl at pH 2.2 has been studied on un-notched specimens stressed in a hard tensilf machite. Austenitizing temperature in the range 1830 to 1400 F has been shown to have a marked influence on the propensity to crack, the loulest austenitizing- temperature producing the greatest resistance to failure. In the nzosl susceptible conditions, the cracks followed the original austenile grain boundaries; but when tlze steels zcere heal treated to inproze their resistance to stress corrosion, the cracks becatne appreciably less branched and slzouqed significant tendencies to become trans granular. Electron metallography of the steels indicated the presence of snzall particles, possibly of titanium carbide, along- the prior austenite grain boundaries and these particles u:ere more readily detectable in the structures that were most susceptible to cracking. Crack propagation rates, which appeared to be dependent upon applied stress and structure, were usually in tlze reg-ion of 0.5 mm per hr and may, therefore, be e.xplained on tlze basis of a purely electrochetnical ,nechanism. However, there is some ezliderzce from fractography that crack extension may be assisted by ttlechanical processes. Anodic stit)zulation reduced the tiwe to fracture, although cathodic currents of small magnitudes delayed cracking-; further increase in cathodic current resulted in a sharp drop i,n fracture litne, possibly due to the onset of hydrogen ewbrittlement. THE use of the high strength maraging steels, with their attractive fracture toughness characteristics, is restricted because of their susceptibility to stress corrosion cracking in chloride solutions. Although this limitation has resulted in investigations of the stress corrosion susceptibilities of these steels, there have been few systematic studies aimed at defining the various parameters that determine the level of susceptibility. It is the case that the usual tests have been performed with the object of defining some stress or time limit, on unnotched or precracked specimens, within which failure was not observed,' but while such results may be of some use in design considerations, they are necessarily concerned only with the steels as they currently exist and not with their improvement to render them more resistant to stress corrosion failure. This omission may be considered unfortunate because the indications are that stress corrosion in maraging steels shows dependence on structure in following an intergranular path, and since experience with other systems of intergranular stress corrosion crack- ing is that susceptibility may be varied by modifying heat treatments, a similar effect may be expected with maraging steels. It is sometimes from such observations that a fuller understanding of the mechanism of stress corrosion crack propagation begins to emerge, leading in time to the development of more resistant grades of material. The present work was undertaken to study only one aspect of the influence of heat treatment upon the cracking propensities of the 18 pct Ni maraging steel, namely the effect of austenitizing temperature, although certain ancillary measurements and experiments have been undertaken. EXPERIMENTAL TECHNIQUES Most of the measurements were made on a steel, A, having the analysis shown below, although a few results were obtained on a steel, B, having a slightly different composition. Both steels were supplied in the austenitized condition, A as 3/8-in-diam rod and B as 1/2-in.-diam rod. Cylindrical tensile test pieces were machined from the rods: the overal length was 2 1/2 in., the gage length 1 in. and the diameter 0.128 to 0.136 in. The stress corrosion tests were carried out with the specimens strained in tension in a hard beam testing machine, the necessary total strain being applied to the specimen over a period of about 30 sec, after which the moving crosshead was locked in position and the load allowed to relax as crack propagation proceeded; the load relaxation was recorded. The load was applied after the specimen had been brought into contact with the corrosive solution, the latter being contained in a polyethylene dish having a central hole through which the specimen passed, leakage being prevented by the application of a film of rubber cement. The specimen was in contact with the solution for over half of its gage length and the solution was exposed to the air during testing. The solution was prepared from distilled and deionized water to which NaCl was added, 0.6N, and the pH adjusted to 2.2 by HCl additions. The composition of the solution

Jan 1, 1969

By John Chipman

The concentration of a solute in a dilute ),zetallic solution may be measured by any of several parame- ters including weight percent, atom fraction, atom ratio, and lattice ratio. The ratio of filled to unfilled interstitial sites is useful for interstitial solutes. A variable 2 proportional to this ratio is used as a measuve of concentration. For component 2 irz a bitzary solution z2 = n2/Ym - nz/b) where b is the numberber of interstitial sites per lattice atom. For a t~lul-ticortzporzent solution this becomes zz = n2/(nl + Cvjnj) in which Vj = - l/b for an interstial solute and +1 for a substitulional solute. In the infinitely dilute solution the activity of an interstitial solute 2 is proportional lo z2. At finile concentration the departure from this limiting law is expressed us an activity coefficient, his coefficient is a function of concentra1io)z expressed as tevactiolz coeffcient 8; is analogous to the jark~iliar e£ bul is found to be independent of concentvation in certain solutions for which data are available. It is found that the same equations may be used to express the activity of a nonmetallic solute, sulfur, in liquid solutions of iron containing other solutes, both metallic and nonmetallic. For a nonmetallic solute or for one which strongly increases the actiuity of sulfur, it is convenient to assign arbitvarily a value vj = — 1. When this is done the derivative is found to be constant in each of the ternary solutions studied. The activity coefficient of sulfur in a complex liquid iron solution may be expressed as where nk is a second-order cross product determined in the quaternary solution Fe-S-j-k. The equation is used to calculate tlze activity of sulfur i)z three sevetl- component solutions. IN thermodynamic calculations concerning dilute solutions it is unnecessary to invoke laws and relations which extend across the concentration range to include concentrated solutions. In most binary metallic systems, as arkeen&apos; has recently pointed out, there exist two terminal composition regions of relatively simple behavior, connected by a central region of much greater complexity. When the solute is a nonmetal there is only one such region and in many systems the concentration range is extremely limited. It is the purpose of this paper to suggest a method for the calculation of activities in such a terminal region in which one or more solutes are dissolved in a single solvent of predominantly high concentration. HENRY&apos;S LAW In the usual textbook statement of Henry&apos;s law, concentration is stated in mole fraction. This has the advantage that it makes Henry&apos;s law thermodynamically consistent with Raoult&apos;s law. Since all measures of concentration at infinite dilution are related by simple proportion it follows that mole fraction, molality, atom ratio, weight percent, or any other unit of concentration can be used with the appropriate constant. At finite concentrations, however, calculations based on the law depend upon the unit employed. Deviations from Henry&apos;s law at finite concentrations depend upon the composition variable employed. They are evaluated in terms of activity and interaction coefficients2 which have become familiar features of metallurgical thermodynamics. It is the purpose of this paper to propose a measure of concentration for metallic solutions containing interstitial or nonmetallic solutes by means of which the calculation of activities in complex solutions may be simplified. The discussion will be restricted to free-energy interaction coefficients3 typified by Wagner&apos;s c|a BINARY SOLUTIONS The several measures of concentration which are to be considered are shown in line a of Table I. The corresponding activity coefficients are in line b and the deviation coefficients, sometimes called self-interaction coefficients, are in line c. Henry&apos;s law simply states that the activity coefficient approaches a constant value at infinite dilution. By adoptihg the infinitely dilute solution as the reference state and defining the "Henrian" activity as equal to the concentration in this state, the activity coefficient is always unity at infinite dilution. This convention is far sim~ler and more useful in dilute solution than emploiment of the &apos;Raoultian" activities and it will be used in the following discussion. The several definitions and equations of Table I will be referred to by means of their coordinates in the table. Early observations of deviations from Henry&apos;s law in metallic solutions were shown graphically4 rather than analytically. For the case of sulfur in liquid iron5 the slope of a plot of logfs vs (%S) was constant in the range 0 to 4.8 pct S, indicating constancy of eh2&apos; in Ic. He was proposed by wagnerz and has been widely adopted. The a function of IIIc recently employed by ~arkenl was designed specifically for dilute solutions. Darken has shown that the value of a12 remains essentially constant for many binary solutions within a substantial range of compositions. The atom ratio is directly proportional to the molalitv.<, a conventional measure of concentration. IVb and C served as the basis for smith&apos;s6 classic studies of

Jan 1, 1968

By W. E. Bergman, P. G. Carpenter, H. B. Fisher

The conditions under which barium carbonate can be used to remove sulfates from drilling muds are limited The amount of sulfate remaining in solution in the system after treatment with barium carbonate is shown to be a function of the concentration of the carbonate and barium ions and the concentration of other electrolytes. Barium hydroxide may advantageously replace barium carbonate when the contamination is not entirely due to anhydrite (calcium in the system is then stoichiometrically less than sulfate) or when the carbonate concentration is high. The effect of substances such as quebracho, phosphates, and chromates, which form complexes or precipitates with barium, is discussed. INTRODUCTION As the complexity of the operations in drilling for oil has increased, more attention has of necessity been directed to the problems pertaining to the maintenance of good drilling mud properties. As a result, chemical treatment of muds has become an important factor in recent years. Some of these treatments have been designed to eliminate the deleterious effects of contaminants in aqueous mud systems by precipitation or other means. The most common of substances encountered during drilling include sodium chloride, cement, and calcium sulfate while various other contaminants: usually in small amounts, may be introduced from the water, clays, and other materials used in preparation of the mud. In certain cases, for example where continued salt-water flow is encountered or massive anhydrite is drilled, special muds may be used so that the physical properties of the mud will remain satisfactory for drilling. In other cases, it is desirable to remove the contaminants so that soluble electrolytes in the system are maintained at low values. For sulfate contamination, the conlmon practice in the field is to add barium carbonate to precipitate the sulfate as barium sulfate Ordinarily such a procedure gives satisfactory results. There have been important instances, however, where addition of barium carbonate was not effective in removal of soluble sulfates from drilling muds. and it is to these cases that the present paper is directed. While it is generally known that barium carbonate is not always effective in removing soluble sulfates from drilling muds, certain inconsistencies appear in the literature as to the limitations of its use, and little explanation for the limitations are given. Varnell and Kimbrel state that "the treatment (with barium carbonate for removal of sulfate) is simple and consists in maintaining a pH of 9 with caustic soda and quebracho." They caution that concentrations of quebracho greater than 1 lb./bbl. may inhibit the reaction. In another publication&apos;, a pH of 10.5 is considered "the maximum desirable," and the indication is that as much as 2.5 lb. quebracho per barrel may be present in the particular mud under discussion. Lancaster and Mitchell5 state that appreciable amounts of phosphates in the mud will inhibit the reaction with barium carbonate and that the phosphate treatment should be discontinued at least 24 hours before addition of the carbonate. Experimental work was initiated to ascertain the factors involved in using barium carbonate for the removal of sulfate contamination in drilling muds. While the experimental data herein reported are limited, they focus attention on the pertinent factors which must be considered for successful treatment. These factors are discussed from a practical and a theoretical view, the latter being supported by equilibrium data found in the literature. Further, it will be appreciated that the factors involved in this specific study will be closely analogous to those in certain of the other chemical treatments which involve a precipitation of the soluble contaminant. A thorough comprehension of these factors should result in a more fruitful application of this type of chemical reaction to the treatment of drilling muds. EXPERIMENTAL A. Reagents Two muds were used during this investigation. For one series of tests, bentonite suspensions were prepared by dilution of a stock suspension containing 8 per cent by weight of bentonite (Aquagel). For another series, a 6.4 per cent ben-tonitic mud weighted to 9.7 lb./gal. with barium sulfate (Mag-cobar) was used. Distilled water was used in all preparations. The quebracho (72% tannin extract) was obtained from the Thompson-Hayward Co. of Tulsa and contained 11.4 per cent moisture (105 C.). All other materials were reagent grade, and concentrations were corrected for water of crystallization, if any. All concentrations are expressed in pounds per barrel (42 gallons). B. Technique The systems — either mud or water — were contaminated with either sodium or calcium sulfate after treatment with the desired amounts of sodium hydroxide and quebracbo. For treatments with barium carbonate an approximately 3-fold excess (5 lb./bbl.) was used over that computed to be required to precipitate all the sulfate as barium sulfate. Barium hydroxide was used in concentrations of 2 lb./bbl. — about

Jan 1, 1949

By P. G. Carpenter, H. B. Fisher, W. E. Bergman

The conditions under which barium carbonate can be used to remove sulfates from drilling muds are limited The amount of sulfate remaining in solution in the system after treatment with barium carbonate is shown to be a function of the concentration of the carbonate and barium ions and the concentration of other electrolytes. Barium hydroxide may advantageously replace barium carbonate when the contamination is not entirely due to anhydrite (calcium in the system is then stoichiometrically less than sulfate) or when the carbonate concentration is high. The effect of substances such as quebracho, phosphates, and chromates, which form complexes or precipitates with barium, is discussed. INTRODUCTION As the complexity of the operations in drilling for oil has increased, more attention has of necessity been directed to the problems pertaining to the maintenance of good drilling mud properties. As a result, chemical treatment of muds has become an important factor in recent years. Some of these treatments have been designed to eliminate the deleterious effects of contaminants in aqueous mud systems by precipitation or other means. The most common of substances encountered during drilling include sodium chloride, cement, and calcium sulfate while various other contaminants: usually in small amounts, may be introduced from the water, clays, and other materials used in preparation of the mud. In certain cases, for example where continued salt-water flow is encountered or massive anhydrite is drilled, special muds may be used so that the physical properties of the mud will remain satisfactory for drilling. In other cases, it is desirable to remove the contaminants so that soluble electrolytes in the system are maintained at low values. For sulfate contamination, the conlmon practice in the field is to add barium carbonate to precipitate the sulfate as barium sulfate Ordinarily such a procedure gives satisfactory results. There have been important instances, however, where addition of barium carbonate was not effective in removal of soluble sulfates from drilling muds. and it is to these cases that the present paper is directed. While it is generally known that barium carbonate is not always effective in removing soluble sulfates from drilling muds, certain inconsistencies appear in the literature as to the limitations of its use, and little explanation for the limitations are given. Varnell and Kimbrel state that "the treatment (with barium carbonate for removal of sulfate) is simple and consists in maintaining a pH of 9 with caustic soda and quebracho." They caution that concentrations of quebracho greater than 1 lb./bbl. may inhibit the reaction. In another publication&apos;, a pH of 10.5 is considered "the maximum desirable," and the indication is that as much as 2.5 lb. quebracho per barrel may be present in the particular mud under discussion. Lancaster and Mitchell5 state that appreciable amounts of phosphates in the mud will inhibit the reaction with barium carbonate and that the phosphate treatment should be discontinued at least 24 hours before addition of the carbonate. Experimental work was initiated to ascertain the factors involved in using barium carbonate for the removal of sulfate contamination in drilling muds. While the experimental data herein reported are limited, they focus attention on the pertinent factors which must be considered for successful treatment. These factors are discussed from a practical and a theoretical view, the latter being supported by equilibrium data found in the literature. Further, it will be appreciated that the factors involved in this specific study will be closely analogous to those in certain of the other chemical treatments which involve a precipitation of the soluble contaminant. A thorough comprehension of these factors should result in a more fruitful application of this type of chemical reaction to the treatment of drilling muds. EXPERIMENTAL A. Reagents Two muds were used during this investigation. For one series of tests, bentonite suspensions were prepared by dilution of a stock suspension containing 8 per cent by weight of bentonite (Aquagel). For another series, a 6.4 per cent ben-tonitic mud weighted to 9.7 lb./gal. with barium sulfate (Mag-cobar) was used. Distilled water was used in all preparations. The quebracho (72% tannin extract) was obtained from the Thompson-Hayward Co. of Tulsa and contained 11.4 per cent moisture (105 C.). All other materials were reagent grade, and concentrations were corrected for water of crystallization, if any. All concentrations are expressed in pounds per barrel (42 gallons). B. Technique The systems — either mud or water — were contaminated with either sodium or calcium sulfate after treatment with the desired amounts of sodium hydroxide and quebracbo. For treatments with barium carbonate an approximately 3-fold excess (5 lb./bbl.) was used over that computed to be required to precipitate all the sulfate as barium sulfate. Barium hydroxide was used in concentrations of 2 lb./bbl. — about

Jan 1, 1949

By J. Szekely, G. P. Martins

A formulation is given for describing the rate of expansion of spherical bubbles rising in liquids the freeboard of which is evacuated. The computer solution of the resultant differential equations has shown that, for low freeboard pressures (less than about 5 mm Hg), on approaching the free surface the bubbles expand much less rapidly than predictable from equilibrium considerations. In other words, in this region the pressure inside the bubbles will be significantly larger than the static pressure in the liquid corresponding to the position of the bubble. These theoretical predictions were confirmed by experimental work, using two-dimensional air bubbles rising in mercury. The important consequence of these findings is that the expansion of gas bubbles in vacuum degassing operations will be a great deal less than expected from hydrostatic considerations. This would lead to a significant reduction in the available interfacial area and may explain the apparent poor efficiency of many vacuum degassing units. VACUUM degassing as a treatment for liquid steel has gained widespread popularity in recent years; the number of known installations exceeds several hundred at the present time.&apos; Although much information is available on both the thermodynamics of the system and the overall performance of various industrial units, much less is known about the fundamental aspects of the process kinetics.2-4 The basic physical situation common to virtually all vacuum degassing operations is the interaction between gas bubbles (swarms of bubbles) and the surrounding molten metal, held in a container, the freeborad of which is at a low absolute pressure. Once formed (or introduced from an external source) the bubbles will ascend, due to the buoyancy forces, and, during this ascent, a significant increase in their volume will occur. This progressive increase in the bubble volume is due to two factors: a) the continuous reduction in the static pressure acting on the bubble during its rise; and b) mass transfer into the bubble from the surrounding molten steel. In a recent paper Richardson and Bradshaw developed equations5 for describing mass transfer into gas bubbles from molten metals at reduced pressures. However, in deriving these expressions it was assumed that the pressure inside the bubble was identical to the static pressure in the adjacent liquid. In other words, the volume of the bubble was considered to be in equilibrium with the pressure of the fluid adjacent to it. This assumption, thus their analysis presented, was thought to be reasonably accurate for most of the bubble&apos;s ascent; however, it was unlikely to be valid in the immediate vicinity of the free surface, held at a low pressure. It was pointed out in the discussion6 that the region close to the surface may be of considerable importance as both the driving force and the interfacial area available for mass transfer are at their highest value here. The &apos; &apos;anomalous" behavior of gas bubbles when approaching a free surface at low pressures was recently confirmed in a preliminary investigation by Szekely and Martins. ?1 Here high-speed motion photography was used to study air bubbles rising in a column of n-tetradecane with a freeboard pressure of 0.1 mm Hg. It was found that significant distortion of the bubbles occurred on approaching the free surface; furthermore, the expansion observed was much less than what one could expect from hydrostatic considerations, i.e., factor a previously discussed. It follows from the foregoing that a detailed study of these phenomena would be justified both from fundamental considerations and because of their potential relevance to technology. The purpose of the paper is to present a more realistic formulation for the expansion of a gas bubble approaching a low-pressure region, together with a comparison of the theoretical prediction with experimental measurement. An inert bubble will be considered in the first instance; it is thought that the understanding of the fluid mechanics is an essential first step toward the realistic formulation of the mass transfer process. This latter problem will be the subject of a subsequent publication. FORMULATION The Physical Model. Consider a spherical bubble, of initial radius Ro, rising in a fluid, having a density pL. Initially let the bubble be at a distance H from the free surface, and at a pressure Pgo, as illustrated in Fig. 1. Pgo, the initial pressure in the bubble, is given by the following equation: pgo = Po = Ptp +pLgH [ la] where Po is the pressure in the liquid corresponding to the initial position of the bubble and Ptp is the pressure at the free surface. The fluid pressure at

Jan 1, 1970

By T. E. Davidson, A. P. Lee

It is known from the early work of Bridgman that the two lowest-pressure transitions (I-II and II-III) are accompanied by substantial and abrupt changes in resistivity and Volume. However, unlike the temperature -induced allotropic transformations observed in such elements as lithium, cobalt, tin, and so forth, there is little actually known about many of the characteristics of the pressure-in&ced transitions. This current work involves an examination of the structural and transformation characteristics of the bismuth I-II and II-III transitions under hydrostatic pressures. The relationship of initial structure to the transformation pressure, rate, resistivity change, and resultant structure is discussed. It is shown that the transition pressure and transformation rate are independent of the presence of grain boundaries and associated anisotropy-induced deformation. An observed hysteresis in both the I-II and II-III transitions is shown. BISMUTH is one of the most interesting of the elements exhibiting pressure-induced polymorphs since it undergoes several allotropic transformations at pressures below 90,000 atm. It is known from the early work of bridman1,2 that the two lowest-pressure transitions (1-11 and 11-111) are accompanied by substantial and abrupt changes in resistance and volume. However, unlike the temperature-induced allotropic transformations observed in such elements as lithium, cobalt, tin, and so forth, there is little actually known about many of the characteristics of these pressure-induced transitions. It is the purpose of this work to examine some of the structural and transformation characteristics of the bismuth 1-11 and 11-111 transitions under hydrostatic pressures. Another interesting characteristic of bismuth is that, in its polycrystalline form, hydrostatic pressures of sufficient magnitude will induce severe progressive plastic deformation in the region of the grain boundaries.3 This deformation, which has also been observed in several other metals, is attributed to the high degree of anisotropy in the linear compressibility of bismuth, resulting in shear stresses in the grain boundaries when it is exposed to hydrostatic pressure. Most thermally induced allotropic transformations in metals, whether of the diffusionless ather-ma1 (martensitic) or isothermal nucleation and growth types, are dependent upon structure and prior history,4 viz., grain boundaries, deformation, and so forth. One logically wonders then whether the transformation characteristics of the pressure-induced polymorphs in bismuth might also depend upon initial structure, particularly with respect to the presence of grain boundaries and associated plastic deformation. In this investigation, the role of grain boundaries and plastic deformation on the characteristics of the bismuth I-II and 11-111 transitions will be established. The rather unique residual microstruc-tural changes associated with these transitions will be presented and discussed. The occurrence of a measurable hysteresis in both the I-II and 11-111 transitions will be demonstrated. The type of transformation mechanism based on the observed transformation rate will be discussed. EXPERIMENTAL PROCEDURE A) Apparatus. The hydrostatic pressure system utilized in this investigation is similar to that previously reported by Bridgman&apos; and Birch and Robertson,5 and has been previously described.3 For the purpose of this work, the pressure medium utilized was a 1:l mixture of pentane and isopentane. Pressure measurement was by means of a manganin coil in conjunction with a Foxboro Recorder. The manganin coil was mounted in the bottom closure and inserted inside the pressure cavity. Based on calibration against a controlled clearance piston gage at approximately 10,000 atm, the estimated error in the pressure measurement was +2 pct. Assuming the nonlinearity in the pressure coefficient of resistivity between 10,000 and 28,000 atm to be not greater than 1 pct, then the estimated error in the range of the I-II and 11-111 transitions was +3 pct. B) specimen Material and Preparation. The bismuth utilized throughout this investigation was of

Jan 1, 1964

By Jean Howard

ALTHOUGH zone melting has found favor in recent years because of its convenience and its faster rate of production of single crystals, the older technique of strain annealing still has a number of advantages. It has been reported1 that the lattice of a crystal prepared in this manner has fewer defects than one grown from the melt and, of course, the control of the external geometry is easier. Also, the diameter of the crystal which can be grown by zone melting has a theoretical limit determined by the surface tension, thermal conductivity, and specific gravity of the material, while the size of that which can be grown in the solid state is limited only by practical considerations. In a program for the study of the structure-sensitive properties of niobium and its alloys it was desirable, for ease of handling, to have available single crystals of large diameter. This requirement dictated the choice of the strain-anneal technique. Induction heating was chosen in the present work in preference to other methods because of its deep penetration of large-diameter sections. A five-turn coil, powered by a motor generator operating at 10,000 cps, is contained in a vacuum chamber. The work is lowered through the coil for both the recrystallization and the crystal-growth steps. Starting with electron-beam melted material, the bars are cold-swaged, recrystallized, strained in a tensile machine, and then subjected to the growth step. Single crystals have been grown under the following conditions: Reduction in area during swaging— 79 to 99 pct, recrystallization temperature—1500o to 1667°C at the rate of 1.25 in. per hr, strain—1.0 to 2.5 pct, growth temperature—1600o to 2400°C at rates from 0.15 to 1.25 in. per hr. Starting grain sizes achieved after the recrystallization step varied from 0.6 to 1.55 mm. The starting grain size was found to be critical; if it is too fine and has any residual cold work, as shown by the presence of a fiberlike texture, a single crystal cannot be grown. Using this technique niobium single crystals have been grown from 0.250 in. diameter and 12 in. long to 1.00 in. diameter and 5 in. long as shown in Fig. 1. The 1-in. crystal is the largest to be reported for a refractory metal as compared to 0.500 in. for molybdenum grown by zone melting.2 As with zone melting, control of orientation is possible by the use of special procedures. Other investigators, see for example Williamson and Smallman,3 have reported that orientation control may be achieved by a bending technique. In the present work the strained rod is partially lowered through the coil to start the growth of the crystal. Then it is removed and bent at a point ahead of the interface between the single and polycrystalline portions. Finally, it is returned to the chamber and growth is continued "around the corner". The amount of bending which can be imparted to the rod is limited by coil geometry which up to now has been 10 deg. However, by repeating the bending and growing operations it should be possible to attain any desired orientation. The perfection of these single-crystal specimens as a function of process variables is being measured by X-ray and metallographic techniques and the results will be reported in a forthcoming paper. This work was partially supported by the Advanced Research Projects Agency.

Jan 1, 1964

By T. D. Guldem, J. L. Kaae

ALLOYS with nominal composition of 45-Fe 35-Ni 20-Cr, ASTM-B-163, known under the commercial names of Incoloy 800 and Sanicro 31 (Alloy 800), are often employed at elevated temperatures for extended periods. Therefore, knowledge of the aging behavior of these alloys is of considerable importance. Significant decreases in ductility and increases in yield strength have been observed in the 45-Fe 35-Ni 20-Cr alloys containing about 0.4 pct Ti and 0.4 pct A1 after long-term aging at 540" to 700"~."~ However, no direct evidence has been presented for precipitation phenomena that might result in such changes. Strengthening effects have been attributed to the effects of local or-dering.3 Since y&apos; precipitation (Ni3A1, Ti) is known to occur in similar alloys which contain more titanium and aluminum,4-7 it was decided to explore the possibility that y&apos; might precipitate in these alloys and might be responsible for the changes in mechanical properties on aging. This note reports some observations of two distict types of matrix precipitates made by means of transmission electron microscopy, in a 45-Fe 35-Ni 20-Cr alloy containing 0.31 pct Ti and 0.4 pct Al. The steel used in this investigation was obtained from the Sand-vik Steel Works; it is designated Sanicro-31 (Alloy 800). The chemical composition of the alloy is given in Table I. Aging of solution-treated material at 700" and 800°C for 130 and 100 hr, respectively, produced the matrix precipitates shown in Figs. l(a) and l(b). It is apparent from these micrographs that the precipitate particles occurred in the form of thin square plates parallel to the matrix cube planes. Extraction replication and selected-area electron diffraction showed that the precipitates were M23C6. Coherency strains, consistent with the semicoherent nature of small M23C6 precipitates,&apos; were evident for certain imaging conditions. In addition to matrix precipitation, preferential precipitation of M23C6 on dislocations was common, as has been reported previously for austenitic stainless steels.&apos;" Specimens aged for longer times (-300 hr) at 700°C exhibited a different type of coherent matrix precipitate in addition to the M23C6. An example is shown in Figs. 2(a) and 2(b). In addition to the few large M23C6 precipitates, small precipitates exhibiting strain contrastl0,ll are present. The "line of no contrast" of the strain field of a given precipitate lies along differ-

Jan 1, 1970