Search Documents

By E. G. Banks

This paper is presented in the belief that metallurgists and chemists will be interested in the practice of grinding in tube-mills in connection with stamps, especially since the records of working here given extend over a lengthy period of time (since May, 1905). The ore from the Waihi mine—more especially that produced in the upper levels—contains a large proportion of hard, chalce-donic quartz, and the gold exists in an exceedingly fine state, conditions which necessitate very fine crushing in order to obtain a high extraction of the precious metal. Before the introduction of tube-mills at the 90-stamp Waihi mill, it was found necessary to stamp through 40-mesh (1,600 holes per sq. in.) woven wire-screens, having a fairly high discharge. The pulp then graded : Per Cent. Per Cent. On 50-mes11, .- 0.1 On l20-mesh ..8.77 On 60-mesh, . 8-74 On 150-mesh,.... 7.48 On 80-mesh,... 16.06 Passed 150-mesh,... 55.19 On 100-mesh,.... 3.66 The stamp-dnty was 2.89 short tons per stamp per day, or a total of 260 tons daily. Although the extraction on this pulp was: gold, from 88 to 90 per cent., and silver, from 74 to 78 per cent., it was recognized that finer grinding of the sands would prove beneficial, provided a machine could be found to do this work economically. Various grinding-mills and pans were tried, but without satisfactory results, the particles of sand being so hard that the capacity of any of the machines was too small to be economical. The results of grinding in tube-mills in other countries were so satisfactory that three tube-mills mere erected at the Waihi

Jan 1, 1908

By H. A. Schwartz, Wolfram Ruff

The spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. $ There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others'-', have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recognized since the introduction of an improved polishing technique8, 9, 10 for cast iron. The problem of deriving from the circular planar intercepts of a mass of spheres of varying sizes their number and size distribution in space has also been satisfactorily solved12, 13 Growth of Nuclei in White Cast Iron It has already been shown1, 3 that the progress of graphitization with time is usual1y consistent with the assumption that nodules grow in size

Jan 1, 1936

By Wolfram Ruff, H. A. Schwartz

The spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. $ There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others'-', have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recognized since the introduction of an improved polishing technique8, 9, 10 for cast iron. The problem of deriving from the circular planar intercepts of a mass of spheres of varying sizes their number and size distribution in space has also been satisfactorily solved12, 13 Growth of Nuclei in White Cast Iron It has already been shown1, 3 that the progress of graphitization with time is usual1y consistent with the assumption that nodules grow in size

Jan 1, 1936

By E. E. Underwood, L. L. Marsh

Aluminum single crystals, alloyed with 0.042 atomic pet Cu and 0.11 and 1.1 atomic pct Mg, were subjected to constant stress creep tests, tensile tests, and hot hardness measurements within a temperature range of 300° to 866OK. Calculations based on Dorn's temperature-compensated time parameter, 6, gave a value of DH, = 27,000 cal per mol for the activation energy of early creep in aluminum single crystals. Correlations have been obtained for aluminum alloy single crystals with the parameter E for solid solution strengthening, as well as with the parameter F for solid solution hardening, by using a valence of three for aluminum. Limited measurements on tensile specimens show that the slip band density tends to decrease with increasing temperature and with decreasing solute concentration. INCREASING interest is being shown in the mechanisms of plastic deformation in single crystals during tensile and creep testing. The complexity of deformational processes in polycrystalline materials has led to a search for simpler experimental conditions. Numerous creep and tensile investigations have been conducted with pure, metallic single crystals. To a lesser degree, the effects of alloying elements on the tensile properties of single crystals have been determined. However: the literature dealing with the effects of alloying additions in single crystals under creep conditions is vanishingly small. This paper represents an attempt to narrow this gap in the knowledge of the subject. Previous investigations of creep behavior at the Battelle Memorial Institute1-1 have been of great value in the analysis of the present single crystal data. It is equally desirable, however, to ascertain the extent of correspondence between the behavior of single crystal and polycrystalline materials. For this purpose, correlations, similar to those developed for polycrystalline aluminum alloys by Dorn and co-workers, have been made with the single crystal data. The results from this study have tended to confirm and extend those correlations to the case of alloyed single crystals. Materials and Procedures Three dilute binary aluminum alloys were prepared for this investigation from 99.99 + wt pct Al, 99.8 wt pct Mg, and 99.92 wt pct (electrolytic) Cu. The nominal compositions of the alloys were 0.042 atomic pct Cu, and 0.11 and 1.1 atomic pet Mg. Precautions were taken to avoid contamination of the stock during melting and casting of the alloys. After a heat treatment of 8 hr at 925°F the alloys were extruded, then machined into) threaded tensile specimens with a 3 in. reduced section and a 0.505 in. diam. Spectrographic examination showed less than 47 ppm metallic impurities in each alloy. The single crystals were grown by the strain-anneal method, with a critical strain of about 11/4 pet giving the optimum results. In general, 3 in. crystals were obtained with the Al-Cu alloy, but smaller crystals in the magnesium alloys necessitated the use of 2 in. and 1 in. gage lengths with the low and high magnesium alloy specimens, respectively. After an electrolytic polish, the orientation of that portion of the specimen containing the largest single crystal was determined from Laue back-reflection photographs. Tensile tests were conducted at a constant load rate of about 2 lb per min. Creep runs were made in a constant temperature room, under constant stress at the higher creep temperatures, and constant load at the lower temperatures. The eloneation was measured to within ±5 microin. by a specially designed capacitance extensometer. The ex-tensometer arms were attached to the 3 in. specimens at the shoulders of the test piece or, where the crystals were smaller than 3 in., by knife-edge grips.

Jan 1, 1957

P. E. McKinney,* Washington, D. C.-Observation made after examination of a number of defective gun forgings, together with a history of their manufacture, has strongly suggested that so-called "flakes" and woody or fibrous fractures are not necessarily analogous and are often caused by entirely different conditions. While some flaked bars may show fibrous areas in the fracture, it does not necessarily follow that the conditions causing these areas are the same as cause the fibrous, or so-called laminated, structures so commonly met in gun forgings subject to transverse tensile test; the fibrous structure formed in some flaky bars are merely incidental to the conditions causing the flakes. It is believed that the so-called flakes, or bright silvery spots, are mainly due to inherent physical defects in the steel, which existed at the very origin of the steel, rather than metallographic defects caused by subsequent irregularities in mechanical or thermal treatment. While great care in forging and treatment may, in a measure, tend to overcome the evil effect of the defects, with many heats of ingots, no such precautionary measures are needed to produce perfect forgings- and with such heats of steel it would be impossible, no matter how carelessly handled, to produce intentionally a forging containing the defects commonly known as flakes. It has been found possible, on several occasions, to actually predict flaky forgings from an inspection f the ingot after it had solidified, and in such cases no amount of careful forging or heat treatment would prevent the occurrence of such defects in the forging. The inspection of the physical condition of the ingot, and especially the character of the shrinkage on. the top of the ingot, has been given too little thought and study in this connection.

Jan 5, 1919

By W. H. Gunniss

When the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of an average sample of this quartz is: SiO2, 96.7; Fe2O3, 0.3; Al208, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then dumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the material would not be plastic enough to mold. After a few minutes' grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left. until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected to when in use in the furnaces. Montana refractories are used in smelters throughout the West. Prospecting for fire clays was also carried on. After experimenting with clays from several different deposits, it was found that a mixture of

Jan 1, 1914

By R. E. Miner, J. K. Jackson, T. L. Wilson

THE nature of the decomposition reactions producing hardening in aluminum-rich A1-Ag alloys is now fairly well understood. The silver is not uniformly dispersed even at temperatures above the solvus line: rather, it is clustered into zones and associated with dislocations.' During quenching, nearly all of the silver segregates into zones' and some is attracted to dislocations, producing stacking faults. Growth of these faults produces the semicoherent y precipitate.1 During aging, the larger zones and the y precipitates grow at the expense of the smaller zones. The large zones persist up to about 350°C; where they redissolve in favor of the y' and y precipitates.' The equilibrium hcp y precipitate occurs both by a cellular reaction at the grain boundaries1 and by growth of the Y' plates to a critical size where incoherency results. Damask and Nowick 4 observed an internal friction peak in an A1-6 at. pct Ag alloy at about 140°C (0.25 cps). The peak was found to exhibit a systematic instability. After aging at successively higher temperatures between 155' and 23Z°C, the peak first migrated to higher temperatures while increasing in height, then returned to lower temperatures and decreased in height. After aging at temperatures above about 200°C, the peak position remained constant while the height decreased very slowly. In quenched specimens, elastic after-effect measurements inhcated a rapid initial transient in peak position from low temperatures up to 155°C. The authors concluded that a stress induced growth and resolution of the clusters and the 7' was the most reasonable mechanism to account for the behavior. It would seem, however, very unlikely that both the clusters and the y' precipitate would provide damping contributions whose relaxation time and activation energies were identical, which is required for them to produce the same internal friction peak. The present investigation was motivated by this apparent anomaly and the development of a very low thermal inertia torsion pendulum5 capable of monitoring transient behavior. Low frequency internal friction measurements were made on four binary A1-Ag alloys nominally containing 5, 10: 15, and 20 at. pct Ag. The results of measurements made on a 10 at. pct Ag alloy in the quenched condition are shown in Fig. 1. There are two peaks apparent in the spectrum, one centered at about 160°C, the second at about 210°C. The two peak spectrum was observed in each alloy, but it was best resolved in the 10 pct Ag specimens. Because of the instability in the internal friction, 4 it seemed possible that the second peak was not a peak at all, but simply a manifestation of a single, sharply transient, peak. This effect has been observed in Au-Ni alloys.6 The existence of the higher tempera-

Jan 1, 1970

By J. N. Hobstetter

It is widely believed that the nucleation of phase transformations in solid metals is accomplished by some type of local atomic fluctuations in the parent phase which arise from spoutaneous difiusion in the metal or alloy system. Under appropriate conditions, these fluctuations are believed to be stable in the sense that the free energy of the entire system is lowered if the fluctuations, or nuclei, grow. Under other conditions they are thought to be unstable in the sense that the free energy is lowered if they redissolve. The criterion for stability is usually taken as the size of the fluctuation. This view has been rationalized by Beckerl in terms of the free energy released by the volume of the nucleus and the free energy associated with the formation of a new surface surrounding the nucleus. The qualitative result of this reasoning is shown in Fig I where the changes in free energy for the surface and volume effects are plotted together with their sum against the radius of the nucleus. There is evidently always a critical size r, beyond which the release of free energy which is proportional to the volume always dominates the increase of free energy which is proportional to the surface area. Borelius2 has also attempted to rationalize the stability criterion for binary alloys, but in terms of the internal concentration of the fluctuations. He has found that, if surface energies are entirely ignored, the fluctuation must still reach a critical concentration if it is to become stable and avoid subsequent dilution. Although the Borelius theory fails to predict many observed nucleation phenomena such as the vanishing of the nucleation rate at the critical temperature, the major premise must certainly be valid. In this paper a reconciliation of the Becker and Borelius views is made by means of a search for nuclei which are at once stable with respect to both size and internal concentration. The increase in free energy per mole accompanying the formation of a nucleus which is just stable, AF., is independent of the path whereby the nucleus is brought into being. It is thus appropriate to seek critical nuclear attributes without reference to the fluctuation mechanism. The rate of nucleation, however, cannot be treated without a detailed understanding of the exact fluctuation process which produces stable nuclei. In this and succeeding papers the purpose will be to find the size, shape and internal concentration of the stable nucleus which is formed with a minimum increase in free energy in a wide variety of systems. The Nature of the Nucleus It is necessary ti have rather detailed knowledge of the nature of a nucleus if AF, is to be computed. Fortunately, enough facts are known or suspected about the nucleus to make possible a detailed analysis. X ray diffraction studies have shown

Jan 1, 1949

By M. A. El-Aouar

Drilling muds are complex colloidal systems. In an effort to analyze the physical properties that affect their performance at high temperature, an investigation was made of the hydrothermal stability of the monoionic hydrogen, calcium and magnesium forms of montmorillonite and attapulgite. Samples were heated to 400°1F in a simple autoclave and analyzed for cation exchange capacity, c-axis X-ray diffraction spacing and pH factor us sodium hydroxide titration dependence. Out of the six monoionic clay minerals tested, calcium montmorillonite and magnesium attapulgite showed the least base exchange capacities and were relatively unaffected to heat. It is concluded that, of the six clays studied, these two clays were the most suitable forms for use in drilling fluids. INTRODUCTION The drilling of deep wells is dependent upon the drilling mud, and problems frequently arise concerning the effect of mud temperature and prolonged heating. Drilling muds are complex colloidal systems. In an effort to analyze their behavior in deep, hot boreholes, it was thought desirable in this investigation to study suspension of pure, monoionic montmorillonite and attapulgite clays before and after hydrothermal heating. Chemically, clays are hydrated aluminum silicates, such as montmorillonites and attapulgites. The structure of montmorillonite is composed of units made up of two silica tetrahedral sheets with a central alumina octahedral sheet. Attapulgite consists of double silica chains running parallel to the c-axis with the chains linked together at their longitudinal edges. The apexes of the tetrahedrons in successive chains point in opposite direc-tions.4,7,10 One of the most important characteristics of clay minerals is their property of sorbing certain anions and cations and retaining them in exchangeable state. The property of exchange capacity is measured in terms of milliequivalents (meq) per 100 gm of clay. The cation-exchange capacities are taken at pH 7 from titration curves which show the relation between pH and milliequivalents of added NaoH.9,11 The following are causes of cation exchange: (1) broken bonds around the edges of the silica alumina units would give rise to unsatisfied charges, which would be balanced by adsorbed cations; (2) substitution within the lattice structure of trivalent aluminum for quadrivalent silicon in the tetrahedral sheet and of ions of lower valence; and (3) the hydrogen of exposed hydroxyls may be replaced by a cation which would be exchangeable. The primary techniques employed to study the effects of hydrothermal treatment were titration curves and X-ray diffraction analyses. Titration curves were useful in characterizing the nature of the clay mineral surface and the stability of the various samples to attack by acid or alkali before and after hydrothermal treatment. X-ray diffraction analyses were used to determine changes in the nature and crystal structure of the minerals present and to determine the cations in exchange positions on the montmorillonite samples. EXPERMENTAL PROCEDURE PREPARATION OF SAMPLES Selected samples of Wyoming bentonite and attapulgite clay from mines along the Georgia and Florida border were purified by centrifugation to remove all particles larger than 2 microns. In preparing magnesium attapulgite, first a 1.00-normal solution of magnesium acetate was prepared. The pH of the solution was adjusted to 7.0 by adding magnesium oxide. One hundred grams of attapulgite clay were mixed in a blender for 30 minutes with the magnesium acetate solution. The attapulgite solution was left overnight, and then filtered in a Buchner funnel. The suspension was leached with further quantity of magnesium acetate solution and then washed with distilled water for 20 days, after which the filtrate was free from magnesium ions. The concentration of magnesium attapulgite in the clay slurry was adjusted and determined quantita-

By R. E. Reed-Hill, W. H. Hartt, W. A. Slippy

An unusual form of double kinking has been observed at the ends of {1121} twins in deformed zirconium. These kinks lie partly outside of the twin and partly inside. While they are undoubtedly closely associated with accommodating the twinning shear into the matrix, they are apparently closely related to other important aspects of twin growth. A mechanism is proposed for {1121} twin growth involving interactions between 1/3 (1120) dislocations in the bend planes and twinning dislocations. It is also shown that boundaries without long range strain fields develop at the tapered ends of the twins. The {1121} twins can, therefore, grow without forming high-energy noncoherent twin boundaries containing large numbers of closely spaced twinning dislocations. NUMEROUS investigators have indicated that slip is often closely associated with deformation twinning. An example is twin accommodation kinking,1-3 where dislocations form bend planes and permit accommodation of a twinning shear within the parent crystal. Another is the incorporation of slip dislocations into twins, as proposed by Sleeswyk and verbraak4 and Ishii and Kiho5 for iron and ß-tin, respectively, and observed in hcp metals by Price.6 In addition, it has been shown that shear discontinuities exist at the points of twin intersections in zinc,7 magnesium,8 titanium,9 ß-tin,10 and bismuth," where the continuity conditions for twin intersections, originally proposed by cahn,12 are not satisfied. A similar situation occurs for zig-zag (1121) twins in zirconium13 and ?-phase silver-aluminum alloys,14 where the twinning shears of the two component twins are not parallel. In all these latter cases additional deformation by slip is believed to accommodate the twinning shear discontinuity. The present paper is concerned with a newly observed aspect of the slip and twinning interrelation, in which two kinks, one inside the twin and the other external to the twin, are formed. These kinks, observed in conjunction with (1121) twinning in zirconium, form to accommodate the twinning shear. A model has been constructed explaining the growth and accommodation of (1121) twins in terms of these kinks. This mechanism may be significant since it is concerned with an important twin mode, which occurs not only in zirconium but also in titanium and hafnium. The practical significance of (1121) twinning has been adequately demonstrated. At 77° K the high ductility of zirconium containing a large number of grains unfavorably oriented for slip is primarily due to (1121) twinning.'5 Also, (1121) twins nucleated at 77°K may grow during further deformation at room temperature. This growth can greatly increase the transverse ductility15 as well as produce large mechanical hysteresis effects.= EXPERIMENTAL PROCEDURE Arc-melted, sponge zirconium plate previously described17 was prestrained 0.65 pct at 77° K by cold-rolling to introduce {1121} twins into the structure. Tensile specimens were cut with axes normal to the plate rolling direction. These specimens were pulled in tension to near the point of failure in an Instron machine at room temperature at a cross-head speed of 2 x10-2 in. per min. This additional deformation caused growth of the twins nucleated by prestrain. Deformed specimens were then prepared for metallo-graphic examination. This included an anodizing treatment18 that made the surfaces sensitive to polarized light, permitting small lattice rotations to be revealed. EXPERIMENTAL RESULTS Nature of the Twin-Kink Band Structure. Fig. 1 is a photomicrograph of a typical specimen after prestrain at 77° K. The structure is characterized primarily by long, narrow, parallel sided (1121) twins which norma1ly traverse the entire grain. Fig. 2 shows several (1121) twins after additional straining at room temperature. These lie near the center of the polarized light photomicrograph and are inclined upward to the right. It is evident that this latter deformation has resulted in appreciable twin growth. The dark regions extending from the ends of these twins are accommodation kinks. The difference in reflected light intensity indicates the

Jan 1, 1969

By J. R. Stack, H. H. Alexander

Prior to 1915, numerous attempts were made to treat tin concentrates in the United States, but for various reasons they were unsuccessful. Tin ore is said to have been found in nearly every state, but none of the deposits has proved to be of commercial importance. An annual output of a few hundred tons in Alaska is the only domestic production; hence any considerable production of tin in the United States must be from foreign ores. The most promising occurrence of tin was found in the Black Hills, S. Dak.; in the early development stage, it was called the Cornwall of America. Associated with the tin is tungsten The story is told that an exceedingly fine specimen of the Black Hills ore was sent to England to encourage stock promotion; the desired effect was produced until a skeptic chipped off a small piece, which the analysis showed to be wolframite. First Attempts at Smelting One of the first promising attempts at tin smelting in the United States was made by R. T. White at Bayonne, N. J., in 1903. Mr. White, after spending some time in England studying the methods of tin smelting, organized a company called the International Tin Co., and erected a plant to treat tin concentrates from the Straits of Malacca. About the time the plant was completed, the English Government placed an export duty of 40 per cent. ad valorem on tin concentrates exported to other than British smelters, which duty made it impossible to operate this plant so the enterprise was abandoned, As this export duty is still effective, the only source of tin-ore supply for the United States is the Bolivian concentrates. Bolivian Tin Concentrates Unlike the alluvial placer deposits, nearly all Bolivian tin occurs in lode deposits and some of the highest grade ores contain only a small

Jan 1, 1924

By John Griffen, David H. Davis

Much of the ground to be covered by this paper was ably covered by a paper presented by Messrs. Morrow and Jordan1 before a joint meeting of the Iron and Steel Section of the Engineers Society of West-ern Pennsylvania and the A.I.M.E. Pitts-burgh Section at Pittsburgh in the spring of 1940. As that paper was not published, the present authors have availed them-selves of Mr. Morrow's kind permission to use information given therein. Similar figures for the latest years available have been added to many statistics originally presented. It is unfortunate that Mr. Jordan's death removes his stimulating guidance and help, which the authors would have welcomed and have found invaluable in the past. One interested in the Pittsburgh seam should not fail to read the exhaustive and authoritative paper by Eavenson2 presented in 1938. As Allegheny, Fayette, Greene, Washington, and Westmoreland Counties contain practically all the reserves and furnish nearly all of the production from the Pittsburgh seam in Pennsylvania at the present time, this area only is intended when reference is made to the Pittsburgh seam in Pennsylvania. On much of the seam in Greene and Washington Counties, which contain a large proportion of the total reserves, insufficient data are available to determine the detailed characteristics of the seam with any degree of finality. It is hoped that the data presented here will fairly well indicate the probable characteristics. Economic Importance of the Pittsburgh Seam The Pittsburgh seam in Pennsylvania is of primary importance as a coal resource, not only because of its substantial reserves but because it contributes such a large proportion of the coal used in the country and an even larger proportion of that used in the manufacture of coke. Mr. Ashley3 placed the estimated recoverable reserves (1935) of the Pittsburgh coal bed in Pennsylvania at 7,500,000,000 tons.* Although a considerable portion of this tonnage is not now suitable for coking coal, because of its high sulphur content, undoubtedly the supply of coking coal will last for many years and that not suitable for coking will furnish industry with an ample supply of energy. In attempting to assess the contribution of the Pittsburgh seam to total coal production and to that of coal used in making coke, one finds that the statistics published annually by the U. S. Bureau of Mines, Minerals Yearbook, do not give tonnages classified as to seams but only as to districts or states and counties. However, it happens that, at present and during much of the

Jan 1, 1944

By David H. Davis, John Griffen

Much of the ground to be covered by this paper was ably covered by a paper presented by Messrs. Morrow and Jordan1 before a joint meeting of the Iron and Steel Section of the Engineers Society of West-ern Pennsylvania and the A.I.M.E. Pitts-burgh Section at Pittsburgh in the spring of 1940. As that paper was not published, the present authors have availed them-selves of Mr. Morrow's kind permission to use information given therein. Similar figures for the latest years available have been added to many statistics originally presented. It is unfortunate that Mr. Jordan's death removes his stimulating guidance and help, which the authors would have welcomed and have found invaluable in the past. One interested in the Pittsburgh seam should not fail to read the exhaustive and authoritative paper by Eavenson2 presented in 1938. As Allegheny, Fayette, Greene, Washington, and Westmoreland Counties contain practically all the reserves and furnish nearly all of the production from the Pittsburgh seam in Pennsylvania at the present time, this area only is intended when reference is made to the Pittsburgh seam in Pennsylvania. On much of the seam in Greene and Washington Counties, which contain a large proportion of the total reserves, insufficient data are available to determine the detailed characteristics of the seam with any degree of finality. It is hoped that the data presented here will fairly well indicate the probable characteristics. Economic Importance of the Pittsburgh Seam The Pittsburgh seam in Pennsylvania is of primary importance as a coal resource, not only because of its substantial reserves but because it contributes such a large proportion of the coal used in the country and an even larger proportion of that used in the manufacture of coke. Mr. Ashley3 placed the estimated recoverable reserves (1935) of the Pittsburgh coal bed in Pennsylvania at 7,500,000,000 tons.* Although a considerable portion of this tonnage is not now suitable for coking coal, because of its high sulphur content, undoubtedly the supply of coking coal will last for many years and that not suitable for coking will furnish industry with an ample supply of energy. In attempting to assess the contribution of the Pittsburgh seam to total coal production and to that of coal used in making coke, one finds that the statistics published annually by the U. S. Bureau of Mines, Minerals Yearbook, do not give tonnages classified as to seams but only as to districts or states and counties. However, it happens that, at present and during much of the

Jan 1, 1944

By R. H. Dourson, B. H. Sage, W. N. Lacey

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943

By W. N. Lacey, R. H. Dourson, B. H. Sage

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943

By Henry J. Joesting

During the past year and a half, the Territorial Department of Mines in Alaska has conducted a modest experimental program for the purpose of determining the extent to which magnetic and resistivity methods can be used in interior Alaska in connection with prospecting, mining and geological studies. Since little information is available concerning previous work,l,2 and since conditions differ considerably from those in most other regions, it was considered advisable to make a general study of the possibilities and limitations of the two methods, rather than a detailed study of any single problem. Problems One of the most serious handicaps to prospecting and geological study in interior Alaska, especially in the mature regions, is a cover of unconsolidated deposits ranging in thickness from a few feet to several hundred feet. These deposits, some of which are permanently frozen, consist of silt with varying proportions of vegetation and windblown material in the valleys and of residual deposits on the hills.3'4 The problems treated here are caused by the existence of this overburden: I. Location of buried placers. 2. Determination of depth and areal distribution of permanently frozen and of thawed unconsolidated deposits. 3. Location of water-bearing beds under unconsolidated deposits. Instruments and Methods Magnetic and direct-current resistivity methods were used because they are relatively simple, rapid and inexpensive and because generally they are well suited to the study of the problems indicated. The instruments used were a vertical Schmidt-type magnetometer and a direct-current resistivity instrument similar to those used by the Geophysical Branch of the U. S. Geological Survey. For placer surveys with the magnetometer, a sensitivity of about 25 gammas per scale division was found suitable. For resistivity studies of frozen and thawed overburden and of underground water, the Lee partitioning method6 was found to be most generally suitable. In the Lee method a central potential electrode is placed midway between the two potential electrodes of the Wenner four-electrode configuration.7 Nonpolarizable electrodes were made from unglazed porcelain pots about 10 cm. high and 5 cm. in diameter. In order to retard evaporation of the electrolyte the sides of the pots were glazed, inside and out, with clear Duco lacquer. For resistivity work in cold weather, a nonfreezing electrolyte consisting of equal parts of ethylene glycol and a saturated water solution of copper sulphate proved satisfactory. Stainless steel rods of 3/4-in. diameter made excellent current electrodes because their bright finish enabled good ground contacts to be made.

Jan 1, 1946

By Henry J. Joesting

During the past year and a half, the Territorial Department of Mines in Alaska has conducted a modest experimental program for the purpose of determining the extent to which magnetic and resistivity methods can be used in interior Alaska in connection with prospecting, mining and geological studies. Since little information is available concerning previous work,l,2 and since conditions differ considerably from those in most other regions, it was considered advisable to make a general study of the possibilities and limitations of the two methods, rather than a detailed study of any single problem. Problems One of the most serious handicaps to prospecting and geological study in interior Alaska, especially in the mature regions, is a cover of unconsolidated deposits ranging in thickness from a few feet to several hundred feet. These deposits, some of which are permanently frozen, consist of silt with varying proportions of vegetation and windblown material in the valleys and of residual deposits on the hills.3'4 The problems treated here are caused by the existence of this overburden: I. Location of buried placers. 2. Determination of depth and areal distribution of permanently frozen and of thawed unconsolidated deposits. 3. Location of water-bearing beds under unconsolidated deposits. Instruments and Methods Magnetic and direct-current resistivity methods were used because they are relatively simple, rapid and inexpensive and because generally they are well suited to the study of the problems indicated. The instruments used were a vertical Schmidt-type magnetometer and a direct-current resistivity instrument similar to those used by the Geophysical Branch of the U. S. Geological Survey. For placer surveys with the magnetometer, a sensitivity of about 25 gammas per scale division was found suitable. For resistivity studies of frozen and thawed overburden and of underground water, the Lee partitioning method6 was found to be most generally suitable. In the Lee method a central potential electrode is placed midway between the two potential electrodes of the Wenner four-electrode configuration.7 Nonpolarizable electrodes were made from unglazed porcelain pots about 10 cm. high and 5 cm. in diameter. In order to retard evaporation of the electrolyte the sides of the pots were glazed, inside and out, with clear Duco lacquer. For resistivity work in cold weather, a nonfreezing electrolyte consisting of equal parts of ethylene glycol and a saturated water solution of copper sulphate proved satisfactory. Stainless steel rods of 3/4-in. diameter made excellent current electrodes because their bright finish enabled good ground contacts to be made.

Jan 1, 1946

By Frederic P. Dewey

By the old method of determining platinum in ores and bullion, the silver-alloy first obtained in the regular course of assay is parted in strong sulphuric acid and the residual metal weighed. This is re-alloyed with silver by a second cupellation and parted in nitric acid, the residual metal being again weighed. Any difference shown between the two weighings is assumed to be, and is called, platinum. Sometimes it is SO, and if any considerable amount of platinum be present, there will be a decided difference between the two weighings; but a slight difference is no real evidence whatever of the presence of platinum. On the other hand, the second weight may equal or possibly exceed the first, even when traces of platinum are present. Again, other members of the platinum group may go into solution in nitric acid more or less. If present, these would be called platinum and escape detection. The method does not provide any direct tests whatever as to the presence or absence of platinum. It is often indecisive, and sometimes gives erroneous results. It is, therefore, quite unsatisfactory. Being called upon many times to determine platinum in a wide variety of materials, particularly when present in very small amounts, I have realized the disadvantages and defects of this old method. In an article on the solubility of gold in nitric acid,' I have briefly outlined a method of gathering a little gold out of a solution containing much silver, which furnishes the basis of

Jan 1, 1913

By M. R. Louthan, C. L. Angerman

In polycrystalline Zircaloy-2 the orientation of zirconium hydride precipitates is influenced by an applied stress during hydride precipitation; hydride platelets are oriented nearly parallel to a compres-sive stress and perpendicular to a tensile tress. 1,2 A similar effect has been observed in the Ti-H system, where precipitation of the low-density hydride platelets occurred on habit planes made energetically favorable by the application of stress. 3 Recently, stress activation of hydride habit planes in zirconium and Zircaloy-4 was also demonstrated. The hydrides precipitated on {101l), {112l} and (2131) planes in both zirconium and Zircaloy-4; however, no platelets were found near the prism-plane positions in the Zircaloy-4 samples. Investigations at the Savannah River Laboratory, using polycrystalline Zirc_aloy-2 samples, have confirmed the (101l) and (1121) habit planes but also showed that the prism planes were active hydride habit planes. Using single-surface stereographic analysis and back-reflection Laue techniques, most of the previously reported habit planes for a zirconium were observed.4"1 and one additional plane, the (1013) plane, was noted, Table I. All the habit planes observed had the form (101l) or { 112l) indicating that these planes are the habit planes for hydride precipitation in poly-crystalline Zircaloy-2. The specimens used in these studies were cut from large-grained weld areas of seam-welded tubing and were hydrided in either a static steam autoclave at 400°C and 1500 psig or in a modified Sieverts apparatus at 400°C.

Jan 1, 1967

By J. H. Brophy, A. I. Prill

The authors have previously investigated the solid-state activated sintering of tungsten powder with various Ni-Cu additions.' Log shrinkage vs log time plots showed changes in slope from 4 to x at intermediate times during the sintering process. This was attributed to a change in the rate-controlling mass-transport process from solution of tungsten into the tungsten-alloy interface to diffusion of tungsten in this interface. It was postulated that the melting of the activating layer should not affect this transport process. However, the superposition of rearrangement due to the presence of a liquid phase complicates the data analysis. It is the purpose of this note to apply the analysis of Prill, Hayden, and rohy' to account for "rearrangement shrinkage'? in liquid-phase sintering of the W-Ni-Cu system. This results in "solution-precipitation stage" shrinkage plots which were comparable to those obtained in solid-phase activated sintering of the same system. If one assumes total shrinkage to be the sum of rearrangement and solution precipitation, the effects can be isolated easily.2 This results in the general equation:

Jan 1, 1967