Search Documents

By Frank Marotta, Louis B. Lesem, Frank Greytok, John J. McKetta

Although one of the primary variables in the calculation of the flowing bottom-hole pressure in gas wells from surface measurements is the temperature at any point and its distribution in the flow-string, only few experimental data are available in the literature and little attention has been given to analysis of the problem. Virtually all of the recently published methods of calculating flowing bottom-hole pressures depend on the assumption that either the temperature is constant at some average value or that the variation is linear with depth. The purposes of this work are to analyze the problem theoretically and to verify the analysis by comparison with experimental data so that practical problems in the analysis of the behavior of gas wells can be solved with greater accuracy, reliability, and ease. MATHEMATICAL OUTLINE OF PROBLEM Assuming that: 1. The mass velocity and chemical composition of the gas stream are constant and in normal gas well operations, the change in linear velocity in the entire flow-string is trivial, 2. The product of the density and heat capacity of the gas is constant, 3. No horizontal temperature gradient exists in the gas stream, 4. Net flow of heat by conduction within the formation and in the gas stream in the vertical direction is trivial in magnitude and can be neglected, 5. The regional vertical geothermal gradient is constant, and 6. The temperature of the gas entering the borehole is constant, and equal to that of the reservoir, a set of two simultaneous, linear partial differential equations with appropriate boundary conditions was derived to describe the temperature distribution in the gas stream and the surrounding formation. These equations were solved by operational techniques for the distribution of temperature in the gas stream. The resulting integrals were evaluated numerically on an IBM 604 at the Machine Accounting Div. of the Railroad Commission of Texas. DERIVATION OF FUNCTIONS FOR THE DISTRIBUTION OF TEMPERATURE The physical system is a circular hole of radius a in an infinite medium with thermal conductivity K, density p8, and heat capacity c,. Under shut-in conditions the well is in thermal equilibrium with the surroundings and the increment in temperature is given by - ?T3/L x. Gas of density pg and heat capacity c.. flows upwardly through this hole in the direction of increasing x with a linear velocity W. Writing a heat balance on an element of gas ?x in thickness, convective heat transfer + conductive heat transfer + energy required to lift a unit mass of fluid = change in energy content. pa2W po Co To - pa2Wpo Co To x+xx - 2apK?x ?T8/?r r=a - Wpa2 po?x/778 = CoPopa2?x?To/?t... Dividing by (copopa2?x) and taking the limit as ?x tends to zero, -W (?To/?x + 1/778Co) + 2 K/a Po Co ?T3/?r r=u = ?To/?t

Jan 1, 1958

By F. Weinberg

The distribution of solute during the progressive solidification of dilute Sn-Ag alloys was determined in both solid and liquid as a jbnction of growth rate, rod diameter, temperature gradient, and solute concentration, using radioactive tracer techniques. The results indicated that partial mixing occurs in the liquid during freezing for most of the conditions investigated, approaching complete mixing for larger rod diameters (>2mm) and slow growth rates. Measured solute distributions were fitted to distribution functions based on diffusion controlled solute transport in the liquid state, by treating the normal solute diffusion constant and distribution coefficient as variable solute transport and segregation parameters. Values of these parameters were determined for the growth conditions investigated. Observations were made to determine whether mixing in the liquid was primarily due to volume changes in freezing or to differences in density between solute and solvent. The former effect was investigated using a selected Sn-Bi alloy as a solvent with zero volume change on fusion, and the density effect was studied using vertical solidifications of Sn-In and Sn-Ag alloys, systems having, respectively, very small and large differences in density between solute and solvent. The result indicate that mixing in the liquid cannot be primarily attributed to either volume changes or density differences. THE solute distribution in progressively solidified rods of dilute alloys, in which there is complete mixing in the liquid, is given by the expression1 where C, is the solute concentration in the solid at the point where the fraction g of the material has solidified, C, is the initial solute concentration and k is the equilibrium distribution coefficient. If it is assumed that there is no significant con-vective mixing in the liquid, then the solute distribution in the initial portion of a semi-infinite rod has been calculated to be2 where t is the time from the start of freezing and x1 is the distance in the liquid ahead of the solid-liquid interface at time t. Expressions [1] and [2] describe the limiting cases of solute distribution in the liquid, i.e., complete mixing, or no convective mixing; in practice it might be expected that the solute distribution would be somewhere between these two cases. pfann3 has suggested that Eq. [I] is applicable for partial mixing, as well as complete mixing, if an effective distribution coefficient k1 is used instead satisfactorily describes solute distributions in rods of magnesium, n-g, and b-sb6 alloys that were progressively solidified from the melt without mechanical mixing. The values of kl were observed to depend on the growth rate4-6 and the temperature gradient.6 The purpose of the present investigation was to measure solute distributions in both the solidified rods and the melt as a function of the solidification variables, and to determine to what extent the observed solute distributions could be described by the above theoretical expressions, keeping in mind that expressions [2] and [3] have been derived solely for the case of diffusion controlled solute transport in the liquid and are not theoretically applicable to

Jan 1, 1963

By Gary J. Brown

AMAX Coal Company, the nation's third largest coal producer operating in Indiana, Illinois and Wyoming, is a division of AMAX, INC., a United States based natural resources corporation that operates world wide. The operations in Wyoming (The Western Division) include Belle Ayr and Eagle Butte Mines. Belle Ayr Mine, located 18 miles south of Gillette, Wyoming, presently employs 440 people. It was started into production in 1973 and has been the largest producing coal mine in the United States since 1977. Final figures will show that the mine was again the largest in 1980 with production levels of approximately 16.1 million tons, total production of coal in the United States being in excess of 800 million tons during this last year. As one of the first commercial producers of sub-bituminous coal in the Powder River Basin, Belle Ayr has served as an example for the many other mines which have since been constructed in that region. The four coal storage silos are the first and most dominant features of the mine to be seen for miles across the Wyoming prairie. Each silo has the capacity to load a 110-car unit train in excess of 11,000 tons. All service facilities at the mine are under one roof. Included in the service building are off ices, warehousing, seven garage bays, and washhouse facilities for all employees. Preparation of coal for shipping at Belle Ayr consists only of crushing from pit-run size to 2 x 0-in. Primary crushing is done under the truck hoppers to 6-8-in. product size. Secondary crushing is performed in the two large crusher buildings. The smallest plant can produce at the rate of 2,500 tph, while the larger can produce

Jan 1, 1983

By S. Kado, G. Derge, L. Yang

Self-diffusion coefficients of silver in molten silver have been measured by means of the capillary-reservoir method in the temperature range 1002" to 1105°C. The results can be .represented by the equation D = (7.10 i 0.06) X 10-4 exp [(—8150 ± 1130)/RT]. The heat of activation agrees within the limit of experimental uncertainty with that for the viscous flow. The validity of the Eyring and the Stokes-Einstein equations are examined on the basis of the self-diffusion coefficients obtained and the known viscosity data of molten silver. MEASUREMENT of the self-diffusion coefficient of silver in molten silver was made in the temperature range 1275° to 1378°K, using the capillary-reservoir method and &"' as the radioactive tracer. The experimental arrangement is shown in Fig. 1. Silver of 99.99 pct purity (fine silver), was melted and degassed in vacuum in a graphite crucible situated inside a McDanel vacuum jacket. The crucible (4 in. tall and 1 in. ID) was protected both at the top and at the bottom with graphite shields and contained about 220 g of silver. The sample holder was a piece of graphite rod (1 in. long and 1/2 in. diam) with 4 capillaries drilled longitudinally into it. The holder was screwed onto a long graphite rod (12 in. long and 74 in. diam) which was connected to a steel disk hanging on a nylon string through a glass pulley. The steel disk kept the sample holder at the center of the McDanel tube and was heavy enough to overcome the buoyancy when the holder was lowered into the molten silver. By turning a handle connected to the pulley through a tapered glass joint, it was possible to raise or lower the sample holder without breaking the vacuum. Two such arrangements were constructed, sitting side by side in 2 Kanthal furnaces. One with non-radioactive silver in its crucible was used for the diffusion run and the other with radioactive silver in its crucible was used for filling the capillaries. To fill the capillaries with radioactive silver, the sample holder was degassed first and then lowered into the radioactive molten silver in vacuum. Purified argon gas was then admitted into the system to push the liquid silver into the capillaries. After cooling in argon, the filled capillaries were polished on emery paper to expose the top of the rod and used immediately as samples for the diffusion run which was carried out at the same temperature as that used for filling the capillaries. During the diffusion run, the samples were degassed in vacuum and lowered slowly into the nonradioactive molten silver before purified argon was admitted into the system. After a predetermined period of time, the samples were raised out of the melt and cooled in argon. The temperature of the melt was measured before and after the run with a chromel-alumel thermocouple inside a McDanel protection tube. Another chromel-alumel thermocouple attached to the outside wall of the McDanel vacuum jacket was used to indicate any fluctuation in the temperature of the furnace during the run, which was found to be less than ± 2°C for the longest run made (93 min). The temperature gradient inside the molten silver was found to be negligible. No significant difference was observed in the results obtained whether the melt was stagnant during the run or was stirred by raising and lowering the sample holder slowly a few times a minute for a distance of about 1/4 in. inside the melt.

Jan 1, 1959

By P. A. Beck, W. D. Manly

In a recent note Sully and Head1 showed that the Cr-Fe sigma phase is isomorplious with the Cr-Co gamma phase, and that the lattice constants are also nearly identical. In a preliminary investigation of the ternary Cr-Co-Fe system at 800°C at this laboratory the above findings were confirmed, and it was found by microscopic techniques, using various etching reagents, that the two binary phases form an urinterrupted series of solid solutions with each other. These solid solutions occupy a straight narrow band which cuts across the 800°C isothermal section of the ternary system, connecting the two binary phases. A detailed investigation of the Cr-Co-Ni ternary system at 1200°C disclosed that here, too, the Cr-Co gamma phase extends deep into the ternary system in the form of a long narrow lip. The fact that this sigma type lattice is sustained even when well over half of the Co atoms in it are replaced by Ni atoms, with relatively little change in the Cr content, clearly indicates that Ni itself has a certain tendency to form the sigma phase with chromium. This tendency is hidden in the binary Cr-Ni alloys, where the sigma phase is not known to occur, but it becomes operative in the presence of a suficient amount of Co. The interpretation of these facts in terms of electron concentrations is rendered difficult by the uncertainty of our present knowledge of the valency electron structure of the transition elements in their alloys. However, Sully and Heal's results and the present work suggest that intermetallic phases with signla type lattice may occur more frequently in these little investigated alloys than heretofore suspected. In particular, it is expected that a similar phase may exist in the V-Co and perhaps in the V-Ni system, in analogy to the known sigma type phase in the V-Fe system, and that all these sigma type phases may form extensive solid solutions with one another.

Jan 1, 1950

By W. G. Wender

This report covers the area producing from limes and sands of Pennsylvanian age, roughly embracing the territory between the Red River on the north and the Llano Mountains on the south, and between Fort Worth on the east and Abilene on the west. It includes Archer, Cooke, Montague, Wichita, Wilbarger, Clay, Baylor and Foard counties in the North Central Texas or Red River Basin area, and Brown, Callahan Coleman, Comanche, Eastland, Erath, Palo Pinto, Stephens, Shackel-ford, Throckmorton, Young and Jack counties in the West Central Texas area. Furthermore, it includes a brief review of development in Jones, Runnels, Haskell and Fisher counties. North Central and West Central Texas during the year 1928 produced an approximate total of 50,948,7461 bbl. or oil. This represents a decrease of approximately 7,720,250 bbl. under 1927 total production. This decrease was due to a slump in production in Brown, Archer, Wichita, Stephens and Cooke counties. Brown County showed the greatest decrease. The 1928 prodction in this county was approximately 4,500,000 bbl. less than the 1927 production. Gross production during 1929 in the North and West Central Texas area can be expected to be lower than in the year 1928. Only one county showed a considerable increase in production. Wilbarger County production increased approximately 3,000,000 bbl. during 1928. Its daily average increased from 9000 bbl. in April to 36,000 bbl. in August. At the close of 1928 it was averaging close to 32,000 bbl. daily. Drilling activity in North and West Central Texas during 1928 showed but a slight increase in completions. The total number of completions during 1928 was 3902, of which 2094 (53 per cent.) were producers, as compared to 3805 completions and 2112 (56 per cent.) producers during 1927. Brown, Young, Wichita, Archer and Wilbarger counties were the leaders in development. The outstanding discoveries for the districts were the Consolidated pool, extensions in the Greyback pool of Wilbarger County, and the Stephens pool, Fisher County.

Jan 1, 1929

By H. D. Dahl, Roger C. Parsons

In order to improve roof stability, Continental Oil Co.'s research program, initiated in 1969, was directed toward defining the geological parameters that affect the severity of roof conditions in any particular area of the mine. In addition, the program was seeking to define why roof falls in the Humphrey No. 7 mine (and in northern West Virginia-southwestern Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. Conclusions and recommendations from this study of roof fall orientation are given.

Jan 1, 1973

J. Parke Channing, New York, N. Y. (communication tb the Secretary*):—Mr. Wright, in his introductory paragraph, says: "It is commonly believed by metallurgists that in copper-smelting, the copper in the slags, which is irreducible by continued smelting, is retained in the form of 'prills' of matte." On a recent visit to Greenwood, B. C., I was discussing with J. E. McAllister, the general manager of the British Columbia Copper Co., and the former metallurgist of the Tennessee Copper Go., this very question; and he held strongly to the idea that the copper in slag was in two forms—one portion contained in occluded matte and the other as an oxide. He believed that this same rule would apply to the silver in the slag. From my experience I am strongly inclined to agree with Mr. McAllister; and it appears quite reasonable that in furnaces treating oxidized copper-ores, and to a less degree in furnaces treating sulphide ores, there is always bound to be present a certain amount of copper oxide and silver oxide, which will behave like any base and get into the slag as such. We all know that in Arizona, in the early days, when it was customary to produce black copper, because the ores were nearly all oxidized or carbonates, and eulphur was scarce, the slags as a rule carried 2.5 per cent. of copper and seldom ran

Jan 1, 1911

By G. A. Crowe, W. T. Bishop

WHILE the literature in the United States on general polarographic technique is extensive, very little appears to be directly applicable to the analysis of flotation tailings. For this reason, it seemed worth while to present a few polarographic methods of ore analysis that have been in constant use in the laboratories of the Hercules Experiment Station for the past few years. At the time of our initial investigation of the polarographic method, there was little or no mention of its specific application to flotation tailings. It was therefore necessary for us to establish suitable conditions for the analysis of our flotation tailings and to consider possible interfering constituents. The polarograph, or dropping mercury electrode, method was discovered in 1925 by J. Heyrovsky and M. Shikata,1 of the Charles University, Prague. This method has since received extensive development and the literature contains many articles on the use of the polarograph for the quantitative determination of metals as well as anions, oxygen in solution, and reducible organic compounds. Kolthoff and Lingane,2 by the publication of their book, "Polarography," in 1941 did much to advance the knowledge and use of the polarograph. In chapter 25 of that book, methods for the polarographic analysis of brass, steel and iron products, alloys, and zinc ore are given. Aluminum,3 cadmium,3.4 cobalt,4 copper,3-9 gold,10 iron,3,11 lead, 3,12,13 molybdenum," nickel,4.8,9 tin,15 and zinc3,4,5,7 in ores have been analyzed by the polarograph. However, most of the work on tailing samples has been published in Russian journals and translations are not yet readily available. In this paper we will describe the method that was developed and used in our laboratory for the determination of copper, zinc, and lead in flotation tailings. PRINCIPLE OF THE METHOD The polarograph is an instrument for applying a potential to a mercury pool and a dropping mercury electrode separated by a solution, and for measuring the resultant electrical current. The procedure is essentially a small-scale electrolysis, in which the voltage required to reduce or oxidize the material identifies it qualitatively and the current measures the concentration quantitatively. Different constituents in a sample may often be determined simultaneously provided they reduce at sufficiently different voltages. An example is the determination of copper and zinc in the same solution. The reduction potentials are quite far apart, as shown in Fig. I. The polarographic method is particularly useful in the range of concentration between those normally determined by spectographic and chemical methods. In

Jan 1, 1946

By L. Grånäs, B. Aronsson

In a recent study of Fe-Si alloys Walter and Koch' observed pairs of dislocations in Fe-6.25 pct Si crystals rolled to reductions of 10 pct and subsequently annealed for 1 hr at 650°C. They interpreted these pairs as being due to stacking faults. From the spacing of the dislocations a stacking-fault energy of 15 to 19 ergs per sq cm was calculated. These authors did not pay any attention to the order -disorder phenomena in Fe-Si alloys. It is the purpose of this communication to report some preliminary results from a study of ordering and its influence on the plastic deformation of Fe-6.0 pct Si alloys. Our results suggest that the dislocation pairs observed by Walter and Koch may have been due to long-range order rather than to stacking faults. The alloys used in this investigation were prepared from pure electrolytic iron and silicon and were melted in argon. After hot working, strip tensile specimens were machined to a gage length of 70 mm and a thickness of 1 mm. The specimens were heat- treated for 2 hr at 1000°C, furnace-cooled, and subsequently deformed 2 pct in tension at 400°C. The strain rate was 5.6 X lo-' sec-'. Thin foils of the deformed specimens were prepared by means of the Bollman technique and examined in a Siemens Elmis-kop I at an accelerating voltage of 100 kv. In the Fe-Si system long-range ordering occurs at a silicon content of about 6 pct Si. In our alloys evidence for ordering is given by selected-area diffraction patterns which show extra reflections consistent with a super lattice of the D0 9 type. In addition, the dislocation arrangement in deformed specimens indicates that long-range order is present. A typical mi-crophotograph of a thin foil is shown in Fig. l. The dislocations are usually straight and parallel and laying in distinct directions. In the commonly observed (111) zone the projections of the dislocations are close to (113) and (oil). Observation of the image position indicates that the two dislocations in a pair have the same Burgers vector and hence constitute a superlattice dislocation.~ According to theory3 a superlattice dislocation in the DO3 structure consists of four ordinary dislocations connected by two types of antiphase boundaries as shown in Fig. 2. In our specimens only two dislocations in each pair have been observed, Fig. 1. The problem is to decide whether the area between these is a NN or a NNN antiphase boundary. Dark-field images using the (200) reflexion (the indices are defined with respect to the DO3-type superlattice) can

Jan 1, 1968

By W. B. Nelligam, J. Tittman

Refinements in radiation logging techniques during recent years have involved increasing usage of scintillation ditectors. These detectors produce voltage pulses whose heights are related to the energies of the gamma rays which initiate them. Analysis of the gamma-ray spectrum, as indicated by the pulse heights, yields information about the chemical elements composing the formations surveyed. Refined scintillation counter techniques can furnish chemical information concerning earth formations in situ, from a study of the gamma-ray spectra emitted by the formation either naturally or as a result of neutron bombardment."' Accompanying the rising interest in gamma-ray scintillation spectroscopy, there has been increased activity in the development of accelerator-type neutron sources (in contrast to encapsulated chemical-mixture sources). Such neutron generators are attractive for several reasons: (1) they greatly reduce radiation hazards to personnel; (2) there is a great reduction in contamination danger if they are lost in the hole; (3) they can produce larger neutron intensities than can conveniently available encapsulated sources; and (4) they are capable of being pulsed, thus permitting new techniques in logging. In the past, both accelerator and encapsulated neutron sources have been used by others in conjunction with scintillation-detector pulse-height analysis. The results have not been too encouraging, due to the interference among different gamma-ray spectral lines and to the fact that the gamma-ray peaks were not too clearly distinguishable above the large and ill-defined background "noise".'.' This paper is a status report on laboratory studies of a technique using a borehole accelerator as a neutron source, which gives an improved scintillation spectrum, thus permitting more accurate chemical analyses of the formations penetrated. The Schlumberger-accelerator neutron source' is presented; the origins of inelastic and of thermal-neutron, capture gamma rays are dis- cussed, and results are given for some laboratory measurements performed in borehole geometry. THE NEUTRON GENERATOR-TUBE ACCELERATOR In the attempt to develop an accelerator neutron source which would have the desirable properties outlined in the "Introduction" and which would operate satisfactorily under borehole logging conditions, a small-diameter, cylindrical, neutron generator tube has been developed. This tube utilizes the principle of accelerating deuterons (heavy hydrogen nuclei) by a high voltage so that they bombard a tritium (heavy, heavy hydrogen) target. The resulting reactions produce large numbers of neutrons of 14 Mev energy. Furthermore, the tube is permanently sealed and, thus, the use of pumping techniques in the sonde is avoided. The tube consists of a pressure control, an ion source in which the deuterons are stripped of their electrons, an accelerating gap down which the deuterons are sped by the high voltage, a secondary electron suppressor and a tritium-loaded target. Obviously, the tube requires auxiliary circuitry in a sonde for the control of the ion source, tube pressure, high voltage and other operating variables. Neutron yields, both continuous and pulsed, have been produced under simulated field conditions in the range between 1 and 10 times those conventionally used in neutron logging applications. For the experiments discussed in this paper, neutron-pulse repetition rates in the range between 500 and 5,000 pulses/sec are adequate. Furthermore, by making suitable adjustments in operating conditions, one can vary the pulse width from a minimum of several microseconds up to dc. As will be seen later, the present application to well logging does not require that one have available pulses of neutrons which are appreciably shorter than the time it takes for fast neutrons to slow down to thermal energy in water. As a consequence, much of our interest has been directed towards the operating characteristics of the tube with pulses longer than about 10 microseconds in duration. Our experience to date shows that tubes can be operated in this manner with reasonably constant, average neutron outputs.

By H. Ries

INTRODUCTION OF the several interesting physical properties of clay which have claimed the attention of investigators in recent years, none is more important than the behavior of the material when heated to temperatures above those of dehydration. Some of the problems to be solved are: 1. The mineralogical changes that take place in firing. 2. The relation between temperature and change in constitution, shrinkage, porosity, etc. 3. The importance of the time factor, as duration of firing, either in reaching a given temperature, or of exposure to a constant temperature. Mineralogical Changes As a result of fusion, reactions take place between the constituents of a clay, which results in a reorganization of the mass, and the formation of new compounds. Of the new minerals developed, sillimanite is the one usually recorded, and has been referred to by a number of observers.1 There appears to he a difference of opinion, however, regarding the temperature at which it is formed. Thus. Klein2 notes that sillimanite forms only above. 1300° C., while Mellor claims that it can develop below 1200° C., the difference in results being conditioned by the time factor. In Klein's experiments the test pieces were fired in 12 hr., while in Mellor's, the temperature rose from 800° to 1180° in 24 hrs., and occupied the same time in cooling back to 800°.

Jan 9, 1917

By W. C. Leslie

The textures of cold-rolled and of annealed iron are compared with those of an iron-0.8 pct copper alloy in which the amount of precipitation after cold rolling was controlled. Previously published pole figures -for cold-rolled and for annealed iron are confirmed. The effects of precipztatiotz after cold rolling are to retain the cold-rolled texture after annealing, to inhibit the formation of the usual allnealing texture, and to produce elongated recrys-tallized ferrite grains. It is suggested that the inhibition of new textures by precipitation after cold rolling is a general phenomenon. A great deal of attention has been paid to the development of texture during the secondary or tertiary recrystallization of ferritic alloys, but very little work seems to have been done on the control of texture during primary recrystallization. If such control were attained, it might be possible to simplify the processing of oriented materials or to change the characteristics of current cold-rolled and an-nealed products. From previous experience, it seemed likely that texture could be controlled by recrystallizing a supersaturated solid solution. Green, Liebmann, and Yoshidal found that the formation of preferred orientation in aluminum (40 deg rotation about <111> relative to the deformed matrix) was inhibited when iron was retained in supersaturated solid solution in the strained aluminum. The authors attributed this inhibition to iron atoms in solid solution. There is, however, an alternative explanation. Green et al, took a highly supersaturated solution of iron in strained aluminum and heated it to an unspecified temperature for recrystallization. It is probable that precipitation occurred prior to and during recrystallization, and it is proposed that the inhibiting agent is this precipitate, rather than the iron atoms in solid solution. It is important to note that precipitation before cold work is ineffective; the effective precipitate is that formed after cold working and either before or during recrystallization. The location and distribution of the precipitate are critical. Precipitation in such a manner has been found to have profound effects upon kinetics of recrystallization and the microstruc-ture of the recrystallized alloys.2-4 It would be surprising, indeed, if this were accomplished with no change in texture. Because of the relative simplicity of the system, and because of previous experience,4-7 it was decided to determine the effect of precipitation on texture in an alloy of iron and copper. Bush and Lindsay5 found an unspecified change in texture in cold-rolled and annealed low-carbon rimmed steel sheets when the copper content exceeded 0.1 pct. MATERIALS In earlier work, the rate of recrystallization of a low-carbon steel was greatly decreased by 0.80 pct copper, and, after the proper treatment, the recrystallized ferrite grains were greatly elongated.4 Accordingly, it was decided to investigate the effect of precipitation on texture at this level of copper content. The iron and the iron-copper alloy were made from high-quality electrolytic iron and OFHC copper, vacuum-melted in MgO crucibles, cast, hot-rolled to 0.2 in., then machined to 0.150 in. The compositions are given in Table I. The plates were heated to 925°C and brine quenched, twice. This produced a ferrite grain size of ASTM 0 in the iron and ASTM 1 in the Fe-Cu alloy. Disk specimens were cut from the heat-treated plates, repeatedly polished and etched, then used to determine (110) and (200) pole figures by reflection. Despite the complication of large grain size, these pole figures strongly indicated a random texture. PROCEDURES The copper content in solid solution in ferrite before cold rolling and recrystallization, and hence, the amount that could precipitate during the recrys-tallization anneal, was controlled at three levels by heat treatment. The specimens as quenched from 925° C were presumed to have all the copper, 0.80 pct, in solid solution. Other samples of the quenched alloy were aged 5 hr at 700°C to retain about 0.5 pct Cu in solid solution.6 A third set of quenched specimens was reheated to 700°C, then slowly cooled in steps, to reduce the amount of copper in solid solution to a very low level. All specimens were cold-rolled 90 pct, from 0.150 to 0.015 in. thick. The rolling was done in one direction only, i.e., the strip was not reversed between passes, with a jig on the table of the mill to keep the short specimens at 90 deg to the rolls. The rolls were 5 in. in diameter and speed was 35 ft. per min. Machine oil was used as a lubricant. In a supersaturated alloy, the maximum effect of the copper precipitate on microstructure and on recrystallization can be developed by a treatment at 500°C, after cold rolling and before recrystallization.&apos;

Jan 1, 1962

By M. M. Leighton

INASMUCH as the arrangements for the preparation of the review of progress and new developments in the field of industrial minerals (non-metallics) were not made until early December, the writing of this review could not be completed in time to appear in this issue and will, therefore, appear in the February issue. However, we desire to call attention to the steadily increasing importance of this group of mineral substances. The recent book, "Industrial Minerals and Rocks," published by the Institute, lists 47 principal varieties of nonmetallic minerals to which may be added several more of lesser importance. Because of the wide variety of uses to which many of these industrial minerals are put, it is difficult to classify them into categories, but to mention a few examples which indicate the widespread industrial employment of these minerals and their products, one may cite: the use of limestone, gravel, sand, clay products, lime, cement, and gypsum in the construction industry; fluorspar, lime, salt, borax, and sulphur in the chemical industry; diamond, corundum, emery, garnet, flint, quartz sand, tripoli. and diatomite in the abrasive industry; fluorspar, limestone, and magnesite in the metallurgical industry; clay, feldspar, fluorspar, flint, chalk, and limestone in the ceramic industry; and asbestos, gypsum, mica, vermiculite, magnesia, diatomite, and rock wool in the heat, sound and elec-

Jan 1, 1940

By Donald C. Barton

OF the four papers that comprise this Technical Publication, three are case histories of individual geophysical prospects, subsequently tested by drilling. The bibliography of Dr. Barton&apos;s published scientific paperst includes investigations in physiography and surface geological mapping, as well as his geophysical papers, and from this list it is to be observed that he early recognized the place of different types of geophysical prospecting methods in the search for geological structures of economic importance. Moreover, his viewpoint was not merely that the structures should be found, but that the geophysical data should be examined quantitatively to determine the geometry of the structures. In other words, that although these data are insufficient to deduce a unique form for the structure that caused the effects measured in the data, the engineering computations should be carried out to give as much of a definite configuration to the structure as the data permitted, in order that the testing of the structures could be conducted in the most economical manner and with the idea that the experience so gained could be later incorporated in the study of structures subsequently found. Dr. Barton continually emphasized the quantitative use of geophysical observations, whereas at the time that he began his specialization in geophysics it was considered sufficient to use observations only qualitatively. He, more than any one else, was responsible for the first volume on geophysical prospecting issued by the Institute in 1929, and his three articles in that volume stressed the quantitative use of geophysical prospecting. The fourth article in this present Technical Publication is a further contribution to this branch of geophysical interpretation, and is a supplement to the paper in the 1929 volume, "Calculations in the Interpretation of Observations with the Eötvös Torsion Balance." From the successful demonstration by Dr. Barton of the usefulness of quan-

Jan 1, 1946

By Donald C. Barton

OF the four papers that comprise this Technical Publication, three are case histories of individual geophysical prospects, subsequently tested by drilling. The bibliography of Dr. Barton&apos;s published scientific paperst includes investigations in physiography and surface geological mapping, as well as his geophysical papers, and from this list it is to be observed that he early recognized the place of different types of geophysical prospecting methods in the search for geological structures of economic importance. Moreover, his viewpoint was not merely that the structures should be found, but that the geophysical data should be examined quantitatively to determine the geometry of the structures. In other words, that although these data are insufficient to deduce a unique form for the structure that caused the effects measured in the data, the engineering computations should be carried out to give as much of a definite configuration to the structure as the data permitted, in order that the testing of the structures could be conducted in the most economical manner and with the idea that the experience so gained could be later incorporated in the study of structures subsequently found. Dr. Barton continually emphasized the quantitative use of geophysical observations, whereas at the time that he began his specialization in geophysics it was considered sufficient to use observations only qualitatively. He, more than any one else, was responsible for the first volume on geophysical prospecting issued by the Institute in 1929, and his three articles in that volume stressed the quantitative use of geophysical prospecting. The fourth article in this present Technical Publication is a further contribution to this branch of geophysical interpretation, and is a supplement to the paper in the 1929 volume, "Calculations in the Interpretation of Observations with the Eötvös Torsion Balance." From the successful demonstration by Dr. Barton of the usefulness of quan-

Jan 1, 1946

By George S. Rice

The A.I.M.E. Ground Movement and Subsidence Committee, proposed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bituminous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O&apos;Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1940

By Sidney Powers

Since the opening of the Wheeler oil and gas field in Carter County and the discovery of oil near Lawton, Comanche County, Okla., in 1904, interest has been aroused regarding the origin of the oil in the Permian "Red Bed" region which lies between the Wichita and Arbuckle Mountains on the north and the Red River on the south. The later development of the Healdton, Loco, Duncan, Fox, and Graham fields south and west of the Arbuckle Mountains has brought the region into prominence. Recent discoveries of Ordovician and of Pennsylvanian fossils in wells in the Healdton field and of Pennsylvanian fossils in the Fox and Graham fields are of such importance from a scientific and a commercial standpoint that the occurrences and the problems arising therefrom are here briefly described. Producing oil and gas sands in the southern Oklahoma fields, with the exception of those in the Cretaceous and underlying rocks in the vicinity of Madill, Marshall County, are associated with the Permian "Red Beds" or with the underlying Paleozoic strata. In the two fields farthest south of the Arbuckle Mountains, Healdton and Loco, production has been entirely confined to sands at depths of 700 to 1400 ft. (213 to 416 m.) and only recently has a producing sand as deep as 1860 ft. (567 m.)l been encountered. These sands are found near and below the base of the red rocks and were supposed by Wegemann and Heald2 to belong in large part to the basal Permian, Wichita formation, or to the immediately underlying formations. Fossils in the blue shales and in the limestones associated with the deeper sands now prove them to be Pennsylvanian and all the producing sands at Healdton are found to be of this age. In the fields nearest the Arbuckle Mountains, the Wheeler sands at a depth of about 700 ft. (213 m.) appear to be of Permian age,

Jan 1, 1918

By George S. Rice

The A.I.M.E. Ground Movement and Subsidence Committee, proposed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bituminous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O&apos;Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1940

By T. L. McCall

The late Walter Herd1 in 1929 gave a full description of past and present conditions in No. 2 mine, Springhill, Nova Scotia, developed theories regarding the cause of these bumps and made certain suggestions regarding possible methods of future development. Recapitulating briefly from Mr. Herd&apos;s paper, the seam is bituminous coal, averages 9 ft. in thickness and has a well defined parting containing fusain about 14 in. from the roof. This roof coal is somewhat stronger than the rest of the seam and has a tendency to cling to the roof. The pitch of the seam where it is now being worked is about 20". The first manifestations of bumps began when the room and pillar workings had reached a depth of cover of 1900 ft. and under continuously increasing depth of cover these bumps increased to such an extent, both in number and severity, that in the year 1924 it became apparent that some change in the system of extraction was necessary. After closely studying all the factors involved and benefiting largely by valuable outside advice obtained by the Provincial Department of Mines of Nova Scotia,2 the system of working was changed from room and pillar to longwall retreating. Mr. Herd&apos;s paper described in detail three remarkable bumps in the year 1928 in April, July and October that affected the 5700-ft. and 5900-ft. East levels, the last bump being so severe both in intensity and in extent of damage done that this district was abandoned. The longwall workings to the west of the slope had been stopped in the year 1926 owing to an inbreak of water, coming from the flooded waste of No. 3 seam lying some 400 ft. vertically overhead. This inflow was not excessive, but a large quantity of water being impounded in the old workings it was considered advisable to take the prudent course and not incur the risk of possibly increasing the flow by further working. This district has remained idle ever since.

Jan 1, 1934