Search Documents

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.'s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By J. C. Mertz, C. H. Mathewson

Accurate knowledge of the solid solubilities of the elements that dissolve in the important base metals is needed for guidance in the preparation and heat-treatment of the alloys derived from these components. While there is still difference of opinion concerning the merits of the X-ray and microscopic methods of determining such solubilities, it is certainly true that the recent extensive use of X-ray diffraction to review the existing constitutional data has revealed many glaring inaccuracies and has brought about a much improved knowledge of phase-boundary locations, which will inevitably come to include all of the important alloy systems. When the work is done with all necessary precautions it appears that in the majority of cases where the solubilities extend beyond a few tenths of a per cent the X-ray back-reflection technique is capable of furnishing the best of information in this field. For the most prolonged and thorough studies it is obviously advisable to combine the results of several methods, in particular, to obtain an agreement between X-ray and microscopic data. This paper reviews the work previously done on the solubilities of phosphorus, arsenic, antimony and bismuth in copper and, in consideration of the uncertainties thus made apparent, presents new X-ray data obtained with the first three members of this group. Copper-phosphorus System Heyn and Baurl found that in slowly cooled alloys phosphorus forms a solid solution with copper up to about 0.175 per cent. Huntington

Jan 1, 1937

By Y. Zimmels, I. J. Lin, I. Yaniv

The potential application of magnetic and electric separation techniques in beneficiation of fine-particle feeds are reviewed. Special features of these techniques are considered and compared with a view to increased amenability of such feeds to separation in electro- magnetic fields. The following techniques are discussed, with reference to those already developed and in use to-date: - Differential-susceptibility separation (DSF). - High-gradient differential-dielectric separation (HGDDS). - High-gradient magneto-gravimetric separation (HGMGS). In this context the new approach - whereby selectivity of solid- solid separation processes, in wet high-gradient magnetic and electric separation, can be improved - is described, including experimental results from DSF and HGDDS tests.

Jan 1, 1980

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By T. J. Koppenaal, M. E. Fine

The critical resolved shear stress of aCu-A1 single crystals has been investigated as a function of composition, testing temperature, and strain rate. The strength, and its temperature and strain rate dependency increase markedly with aluminum content. The solid solution strengthening at 4.2°K is much larger than at room temperature. The activation energy for the low temperature dislocation cutting process increases from about 0.17 ev for a 0.5 at. pct A1 alloy to about 0.50 ev for a 14 at. pct A1 alloy. This result is attributed to an increase in the width of extended dislocations due to the known decrease in the stacking fault energy. In addition, the activation volumes at 4.2 and 77°K decrease with aluminum additions. Concerning the solid solution strengthening in the 296° to 373°K range, no definite conclusions are reached, but it is suggested that subgrains and cutting of subgrains are important. In a previous paper,' the authors reported that adding aluminum to copper produces two types of strengthening: a yield point effect and an increase in the lower yield stress. This behavior is illustrated in Fig. 1 by shear stress-shear strain curves of furnace-cooled single crystals of pure copper and Cu-14 at. pct A1. The yield point effect, At, was thoroughly studied previously1 and shown to be associated with short-range order. The present paper reports an investigation of the lower-yield stress in aCu-A1 single crystals as a function of composition, testing temperature, and strain rate. EXPERIMENTAL PROCEDURE Single cryski1 tensile specimens were prepared in the same manner as previously described.l Briefly,

Jan 1, 1962

By Carl H. Beal, E. D. Nolan

In February, 1918, the conclusion was published by Lewis and Beal "that wells of equal output on the average will produce equal amounts of oil in the future, regardless of the ages of the wells." This conclusion was based upon the study of data collected principally in Oklahoma and was not known at that time to be true for other oil fields. An abundance of statistical proof was later collected by the senior author of the present paper, which showed that the conclusion was undoubtedly well founded and that it applied to other fields as well. Accordingly, it was later restated2 as the "law of equal expectations" as follows: "If two wells under similar conditions produce equal amounts during any given year, the amounts they will produce thereafter, on the average, will be approximately equal, regardless of their relative ages." Although only scanty data from the California oil fields were available at the time this publication was prepared, sufficient information was analyzed upon which to base the insert on Fig. 80, which showed beyond a doubt that the law held at least for a part of the Midway oil field in California. Recently the authors have collected more complete data in California, and it is the purpose of this paper to explain the method used in demonstrating the truth of the law and, in addition, to give several methods by which curves constructed in accordance with this law can be used in a practical way with ease and accuracy. The Family Curve The law of equal expectations means that each individual of a group of wells producing under similar conditions will decline along approximately the same type of curve, the rapidity of decline varying with the output

Jan 1, 1921

By D. V. Carter, Dan C. Williams, Franklin M. Hackbusch

During 1939 little of consequence happened in East and East Central Texas in the way of oil discoveries. At the end of the year, there were 47 oil and gas fields in the district. Twelve other fields, 11 oil and one gas, have been abandoned. The ranking fields in order of the number of completions for the year were East Texas, Talco, and Rodessa (Texas portion). There were 511 oil wells (distillate wells included), 32 gas wells, and 257 dry holes completed in the district. Exploration, Discoveries and Extensions During the year, 113 exploratory wells were drilled, the same number as in 1938; four oil fields and one gas-distillate field were discovered. Perhaps the most important discovery, which has been named Barron field, was that of M. Samuel et al., No. 1 Barron in Limestone County. The wells in this field are of the gas-distillate type. Other than the Talco and Sulphur Bluff fields, which produce oil from the Paluxy sand (Upper Trinity), this is the first field on the Corsicana-Mexia fault zone to obtain commercial production from deeper Trinity strata. This "pay" is the Petit lime of the Lower Glen Rose of the Trinity group. The four oil discoveries were: Redland, Angelina County; Bazette, Henderson County; Rowe and Baker, Henderson County; and Marion County Shallow in Marion County. It is believed that the Bazette field, Navarro County, represents an extension of the Flag Lake field. For details concerning discoveries, extensions and important wildcat wells drilled during 1939 see Table 2. Production and Proration The district produced 175,053,729 bbl. of oil (distillate production included) which is a decrease of 4.0 per cent from the 182,369,484 bbl. (distillate production included) produced during 1938. The district's production for the year 1937 was 208,594,453 bbl. The East Texas

Jan 1, 1940

By D. V. Carter, Dan C. Williams, Franklin M. Hackbusch

During 1939 little of consequence happened in East and East Central Texas in the way of oil discoveries. At the end of the year, there were 47 oil and gas fields in the district. Twelve other fields, 11 oil and one gas, have been abandoned. The ranking fields in order of the number of completions for the year were East Texas, Talco, and Rodessa (Texas portion). There were 511 oil wells (distillate wells included), 32 gas wells, and 257 dry holes completed in the district. Exploration, Discoveries and Extensions During the year, 113 exploratory wells were drilled, the same number as in 1938; four oil fields and one gas-distillate field were discovered. Perhaps the most important discovery, which has been named Barron field, was that of M. Samuel et al., No. 1 Barron in Limestone County. The wells in this field are of the gas-distillate type. Other than the Talco and Sulphur Bluff fields, which produce oil from the Paluxy sand (Upper Trinity), this is the first field on the Corsicana-Mexia fault zone to obtain commercial production from deeper Trinity strata. This "pay" is the Petit lime of the Lower Glen Rose of the Trinity group. The four oil discoveries were: Redland, Angelina County; Bazette, Henderson County; Rowe and Baker, Henderson County; and Marion County Shallow in Marion County. It is believed that the Bazette field, Navarro County, represents an extension of the Flag Lake field. For details concerning discoveries, extensions and important wildcat wells drilled during 1939 see Table 2. Production and Proration The district produced 175,053,729 bbl. of oil (distillate production included) which is a decrease of 4.0 per cent from the 182,369,484 bbl. (distillate production included) produced during 1938. The district's production for the year 1937 was 208,594,453 bbl. The East Texas

Jan 1, 1940

By S. Weissmann, P. R. Swann, D. F. Wriedt

The sizes and density of precipitates in an intemally oxidized 0.19 wt pct Al-Ag single crystal have been determined by low-angle X-ray scattering and by transmission electron microscopy . The correlation in particle sizes measured by the two techniques is reasonably good. For an oxidizing temperature of 800°C the particles were found to INTERNAL oxidation of dilute alloys of aluminum in silver produces an oxide which has an excess of oxygen compared to Al2O3.' It is believed that the excess oxygen is an indication of the small sizes of the oxide particles. Depending upon the particular model chosen for the oxide structure, the size of the o-A1 particles can be calculated as a function of the oxygen-to-aluminum ratio. These calculations pre- have diameters in the range 30 to 140A, with a mean size of about 50.4 as observed by electron microscopy. At lower oxidizing temperatures, less than 600°C, no clearly resolved particles are formed, and it is suspected that if A1-0 clusters exist they must be exceedingly small, i.e., 10A or less in diameter. dicto that the particles would vary in size from 15 to 100A. This range of sizes is amenable to detection by both small-angle X-ray scattering and transmission electron microscopy. This paper compares the cluster sizes in such internally oxidized A1-Ag alloys determined by transmission electron microscopy and small-angle X-ray scattering. SPECIMEN PREPARATION Single crystals were prepared from 99.9999 pct Ag, obtained from Cominco Products, and 99.99 pct Al, obtained from Aluminum Co. of America. All melting operations were carried out in graphite molds under flowing purified hydrogen in a horizontal zone refiner. The silver was first degassed,

Jan 1, 1964

By Arthur Gates

INTRODUCTION RITTINGER'S law of the energy expended in crushing is, as roughly stated by Professor Richards,1 that the work of crushing is proportional to the reduction in diameter; or, as I have more fully expressed it: "The work done in crushing is proportional to the surface exposed by the operation; or, better expressed for this purpose, the work done on a given mass of rock is proportional to the reciprocal of the diameter of the final product-assuming that all the mass has been reduced to one exact size, which is only theoretically possible.?2 Kick's law is stated by H. Stadler as follows:3 "The energy required for producing analogous changes of configuration of geometrically similar bodies of equal -technological state varies as the volumes or weights, of these bodies." In other words, the energy expended is porportional to the volume reduction, instead of the diameter reduction. That these two laws would give widely different results may be shown by a simple imaginary case. A ton of 16-in. cubes is broken to 1 -in. cubes at the first operation, and these are broken to 1/16 -in, cubes at a second operation. Since the first operation produces only one-sixteenth as much new surface as the second, the ratio of energy expended in the two operations would be by Rittinger's law as 1 to 16. By Kick's law, since the volume-reduction ratio is the same in both cases, the ratio of energy would be 1 to 1. This discrepancy is great enough to challenge a test by actual experiment, of which there has been, hitherto, but little compared with the amount of argument. The present paper is the record

Jan 9, 1915

By S. F. Reiter, You-Chao Liu, W. R. Hibbard

Cyril Stanley Smith in his classic 1948 Institute of Metals Lecture&apos; noted in the case of annealing twins that: "It is well known that approximately the same number of twins per grain and the same general geometry are maintained in large grains as in small ones, a fact that certainly suggests a mechanism such as the above where boundaries and twins grow proportionately together. If this view is correct, a spherical grain should have no mechanism for keeping its twins." Such a constancy of twins per grain would be of particular interest as a tool for the study of the origin of annealing twins. It has been proposed by Mathewson2 and later by Barrett3 that in face-centered cubic metals slip occurs in the {111} Plane by <112> shears which combine in pairs to produce the macroscopically observed <110> movement. This proposal is schematically inviting since <112> slip permits the atoms of one plane to move along the interatomic valleys of its neighbor rather than up the hills across the atom sites. There is strong experimental evidence? that annealing twins result from the growth of nuclei in the form of "twin faults" produced by single <112> shears. It is possible that more twin faults would form at low deformation temperatures than at high ones, because the more rigid lattice may increase the tendency to "freeze" the twin faults and prevent their dissipation in slip. This is suggested by (1) the greater resistance to slip at low temperatures and (2) greater tendency toward mechanical type twinning at low temperatures (a summary of these factors is presented by Seigle and Brick5). These considerations would suggest the following: a. Constant twin/grain ratio for specimens deformed constant amounts at a constant temperature, but annealed at various temperatures above the recrystalliza-tion temperature. b. Larger twin/grain ratios for re-crystallized specimens previously deformed constant amounts at lower temperatures. The purpose of this investigation is to test these considerations. One half in. rods of phosphorous deoxidized electrolytic copper and 70-30 alpha brass (68.36 pct Cu, 0.005 pct Pb, 0.01 pct Fe, 31.62 pct Zn remainder) were rolled to a thickness of 0.350 in., milled to specimens 0.350 X 0.437 X 2 in., and annealed at 700°C to an average grain size of 0.065 and 0.090 mm, respectively. These specimens of each metal were then rolled 50 pct reduction in thickness and annealed one hour under conditions which were all combinations of the following: Rolling Annealing Temperatures. Temperatures. °C °C -70 400 25 500 200 600 Standard metallographic techniques&apos; were used to prepare specimens. By the method of lineal analysis7 using a minimum of ten samples of fifty grains each for each specimen, the ratios of twins* per total grains, twins per twinned grain, twin families* per total grains and twins per twin family were determined. Recrystallized grain size was determined by A.S.T.M. comparison methods.8 All observations were made on the rolling plane. The results are tabulated in Table 1.

Jan 1, 1950

By J. D. Cannon

SLAGS studied in this investigation were from 0.25 to 0.35 pct plain carbon steels and were melted in a 3-ton acid-lined Lectromelt furnace with a 2500-kva transformer. The melting process employs a short, violent boil, which is partially blocked, and the desired carbon content is adjusted by pig iron or iron ore, depending on the preliminary carbon. A relatively small volume of slag is used in refinement. Bottom is here defined as that portion of the furnace that comes in contact with the molten metal, or all the surface below the slag line. Bottom trouble-i.e., holes in the bottom lining-is very seldom experienced at our plant. We have been watching the bottom lining over a period of some boo heats in the hope of having holes large enough to supply data for this report, but none occurred during that period. The bottom is eroded uniformly, occasionally with slightly deeper depressions around the taphole.

Jan 1, 1947

By Ralph Sherman

IN these days of intense competition for the domestic fuel market much is heard of the low efficiencies with which solid fuels, and most particularly bituminous coal, are burned in domestic heating equipment. In contrast to the every-day operating efficiencies of 85 and 90 per cent in large, central, electric-generating stations, efficiencies of 50 per cent and lower are cited for the hand-fired home furnace. Just as the miles per gallon of gasoline is only one of the factors that determine the cost of operation of an automobile, so the thermal efficiency is only one factor in the cost of domestic or other heating. The purpose of this paper is to analyze the total costs of domestic heating by various fuels and types of equipment, to determine the relative importance of efficiency and other factors, and to discuss what this signifies relative to the future of the use of fuels in the home.

Jan 1, 1933

By H. Reginald Hardy, Y. S. Kim

Recent studies of inelastic behavior and acoustic emission in geologic materials further validate the concept that such materials may be considered to consist of an elastic media containing an array of pores and cracks. In the present paper this concept is investigated further by experiments in which the mechanical behavior of a number of geologic materials were studied in detail at low stress levels using ultrasonic pulse methods. Experiments were carried out on cylindrical test specimens of Indiana Limestone, Tennessee Sand- stone and Barre Granite under relatively low confining pressures (0-5000 psi). Analysis of data from these experiments indicated that there existed a low-level critical stress at which there appeared to be a transition in the mechanical behavior of the material. Under triaxial stress, results indicated that the differential critical stress was relatively independent of confining pressure, i.e., the mechanism responsible for the transition in mechanical behavior was governed by a maximum shear stress criteria.

Jan 1, 1971

By John A. Church

Early in the month of Angust, 1877, a miner in Gold Hill, Nevada, made the unlucky remark that, according to his observation, that month was usually quite free from accidents in the mines. Never was presage wider from the truth. When the month closed twelve mishaps had occurred, killing six and wounding nine persons, and for the rest of that year the Comstock mining communities were kept in a ferment by the frequent occurrence of appalling disasters. There was a real tidal wave of calamity sweeping over the mines, which has not been repeated since, and according to cornmoll report was never known before on the Comstock. I was much interested in studying the character of these misfortunes, which also aroused concerted action on the part of the miners, and I have collected a list of the accidents which took place from July, 1877, to May, 1879. The number in this period of twenty-two mouths

Jan 1, 1880

By S. R. Mitchell, M. C. Fuerstenau, A. M. Gaudin

The two principal attributes of a thickener pulp are its settling rate and the ultimate pulp density of the thickened mud. Testing for evaluation of thickening attributes of a pulp has usually been done batch-wise by placing the pulp in a one-liter glass graduated cylinder and noting the position of the boundary between clear liquor and mud as a function of time. Refinements in testing have included repulping a thickened mud to various dilutions and evaluating the settling rate on these various repulped muds. This is considered to make possible an estimate of the settling rate as a function of pulp density and therefore to pinpoint the slowest settling pulp which ought to be critical from the standpoint of thickener plant design. Finally, tests are sometimes made with model-size continuous thickeners of arbitrary size. In batch tests it is generally accepted that the behavior of a pulp is described by a curve such as the one shown in Fig. 1, in which the position of the boundary between clear liquor and mud (the mudline) is plotted against time. It has also been assumed that the initial settling rate (the slope of the line segment AB) is descriptive of the pulp and independent of the size and shape of the container. Where the settling rate is slower and clearly a function of time (portion CD of the settling curve), it has been assumed that the data are not of much use because of the intrusion of compacting phenomena. The next important datum is the height. PE, which is a measure of the so-called ultimate pulp density. This quantity is assumed to be characteristic of the pulp and independent of the container. When actual data are recorded, results are rarely exactly according to this theory and numerous deviations may be noted. For example, some pulps seem to require an appreciable delay before beginning to settle, as in line AF. This is spoken of as representing the need for an induction time for flocculation. It has seemed desirable to explore thickener data with a more sensitive charting tool than is afforded by the coordinates of Fig. 1. Instead of relating the position of the mudline to time, it has seemed desirable to relate the rate of descent of the mudline to time. This, in effect, amounts to charting the slope of the line in Fig. 1, or the derivative of its ordinates, against the same abscissas. Fig. 2 shows the new chart for the curve ABCDE of Fig. 1. When this new tool was applied to data obtained, for example, with sized clay pulps, astonishing differences appeared. Apparently the traditional tool conceals differences instead of revealing them, whereas the new method emphasizes them. It seems, also, that both charting methods have their uses. In this article attention is focused on the effects of pulp density and container height as they affect the settling behavior of flocculated suspensions of a sized kaolin. The thesis by M. C. Fuerstenau&apos; gives more details than this summary, as well as some information about the effect of other variables. Sized fractions of kaolin were used, supplied through the courtesy of S. C. Lyons of the Georgia Kaolin Co. Large batches were made by agitation in a flotation machine and in a glass jar equipped with a mixer. The settling vessels were 2, 4, and 6-in. diam glass cylinders of various heights. Pulp Dilution: The effects of pulp dilution on sedimentation behavior are shown in Figs. 3, 4, and 5. Fig. 3 shows data on pulps ranging from 2.44 to 16.7 pct solids initial pulp density, flocculated with Separan and charted in the traditional manner. At least two of the lines appear nearly straight in their early sections, but neither of the others does. Each of the curves in this figure includes a region labeled

Jan 1, 1960

By John Chipman

THE equilibrium between titanium in liquid iron and titanium oxides has been studied by Hadley and Derge.&apos; They have shown that a minimum occurs in the oxygen content of the metal between 0.1 and 1.0 pct Ti, but its exact level was not fixed. The oxide phase in this minimum range was principally TiO, containing some iron oxide. On the other hand, for concentrations above 5 pct Ti the oxide phase was TiO and the oxygen content of the metal increased rapidly with increasing titanium content. From their observations and the free energy of Ti0 and TiOz reported by Kelley and ah,&apos; it is possible to derive approximate values for the activity coefficients of titanium and oxygen in liquid iron-titanium alloys and the conditions for equilibrium in steel deoxidation. Neglecting possible departures from the stoichio-metric composition, the condition of equilibrium with Ti0 may be expressed as follows: TiO= Ti_ + C) log K = log NTl + log [% O] + log yTi + log fQ Here as a matter of convenience the titanium concentration is expressed in mol fraction while that of oxygen is in weight percent. The activity coefficients are yTi and fo. The value of log fo approaches zero as the concentration of titanium approaches zero, while that of log yTi approaches a limiting value of In Fig. 1 the sum of log NTi + log [% 0] is plotted for mol fractions of titanium between 0.05 and 0.50. The smooth extrapolation gives a value of —4.15 which corresponds to log K — log y:i . We therefore have the equation: According to the data of Kelley and Mah,&apos; the free energy of formation of Ti0 at 1900°K is -82,400 cal. The free energy of solution of half a mol of oxygen in iron, taking 1 pct 0 as the standard state, is -29,300 cal. From these we write: From these equations the activity coefficient of titanium at infinite dilution in iron is found to have a value of 0.011 or log y°. = -1.96. This is only an approximate value but is certainly better than the estimated 0.05 in Basic Open Hearth Steelmaking To obtain approximate values for the activity coefficient at intermediate concentrations, it is as- sumed that log yTi(l is constant and equal to -1.96. This corresponds to a value of E;: = 3 In yTi/aNTi = 9.0 which is not unreasonable We now have the value for the activity of titanium and the percentage of oxygen in equilibrium with TiO. It is therefore a simple matter to calculate the activity coefficient of oxygen which is shown in Fig. 2. The effect of titanium is rather large, being comparable to that of vanadium, but not so large as has been reported for aluminum. The slope of the line at low concentrations corresponds to E: = aln yo/ aNTi=-0.37. At concentrations below 1 pct Ti the deoxidation constant and oxygen content for equilibrium with TiO, can be calculated from the foregoing data and the free energy of formation of TiO,, which according to Kelley and Mah is -144,600 cal at 1900°K. The free energy of solution of oxygen has been given; that of Ti to form a dilute solution with 1 pct Ti as the standard state is RT ln (0.5585 y:i/47.9) = -34,800 cal. From these data we find (for concentrations in wt pct): TiO, = Ti + 2 -0; hFTgO0= + 51,200 cal log if =-5.89 The interaction coefficients, concentrations being expressed as wt pct, are e;: = alogfTi/a[% Ti] = +0.048 and e:&apos; = a logfo,/a[ojTi] = -0.187. The calculation gives the following results which, in view of the impurity of the oxide phase, must be regarded as approximate:

Jan 1, 1961

By J. B. Newsom

IN the September 1936 issue of MINING AND METALLURGY the pioneer work of boring a 5-ft. shaft to a depth of 1125 ft. at the Idaho Maryland mine in California was described. Later, a Bureau of Mines Information Circular (No. 6923) gave additional data. In re¬cent months still further progress has been made in this technique through the sinking of a 5 1/2-ft. shaft for Pickands, Mather & Co. at their Zenith mine, Ely, Minn. The present work was done with new carefully designed equipment and several experienced men so that progress, as shown below has been much better:

Jan 1, 1938

By L. L. Brundred

The major portion of the production of the Gulf Coast area, represented by South Texas and South Louisiana, comes from the flanks of well-defined salt domes. This oil, containing an excellent lubricating stock, ranges from 17° to 28° Be. gravity. Some lighter oil is encountered but the life of such fields is, in general, an open question. In fact, there are few light-gravity fields which have proved of much value. In all of the fields water encroachment, or, more properly, water produced with the oil, is a vital factor. After the first head of high-pressure gas is removed, ever-increasing percentages of water appear, and naturally the life of the wells is materially affected thereby. The sands are, as a rule, extremely fine, very soft, and must be carefully excluded from the hole by the use of fine screen to prevent sanding up. All sands are tipped at such extreme angles as to make coring essential for the location of water strata, oil-bearing sands and important shale. beds. Even with modern coring, the correlation of logs is a difficult problem. Due to the fact that the bulk of the oil is refined for its lubricating properties, little attention has been paid to losses by evaporation in the field. This is largely influenced by the fact that the major companies have set a price schedule, showing but two grades, "A" and "B." The average oil company, therefore, does not attempt to use the gas-lift but relies primarily on the air-lift and then only on wells considered to be particularly adapted to its use, namely those capable of producing large quantities of fluid and yet not having sufficient "kick" to flow. Furthermore, as the gas contained in the reservoirs is mostly ricthane such gas being very quickly vaporized and produced in large quantity in the early life of the fields, there is little gas left after the first flush flowing period of the wells. In fact, it is very generally conceded that gas is a precarious fuel to depend on in any of the coastal fields. This situation largely accounts for the fact that air, as the lifting medium, is almost universally used. In the average field, wells are drilled on the flanks of the domes in close proximity to one another, largely on account of the extreme dips of the formation and "town lot" leases, and space to set up machinery and

Jan 1, 1928