Search Documents

By Arthur C. Simmons

The State of Pennsylvania produces approximately 60 per cent of the total production of Pennsylvania Grade oil, and naturally represents the dominant factor in the area producing that grade. The producing area comprises the states of New York, Pennsylvania, West Virginia, and a small part of Ohio. The importance of this area is too commonly neglected because it produces only 2 per cent of the total amount of crude produced in the United States. It is, of course, unimportant in its percentage of total crude production, but extremely important for its production of lubricating oil. The lubricating fraction from a barrel of Penllsylvania Grade crude oil represents about 22 per cent of the total, whereas the lubricating fraction from the total United States production represents only about 2.5 per cent of the crude oil. The Pennsylvania Grade area produces about 6,000,000 bbl. of lubricants, which is 15 to 20 per cent of the total produced in the United States. All Pennsylvania Grade lubricants are classified as "high-grade," and with a production of 15 to 20 per cent of the total lubricants, it appears probable that the Pennsylvania Grade area accounts for 25 to 50 per cent of the high-grade lubricants produccd in the United States. Production Bradford Field The production figures quoted in Table I apply only to the part of the Bradford held that lies wholly within the state of Pennsylvania; approximately 15 per cent of the Bradford field is in Cattaraugus County, New York, and 10 per cent of the production is obtained from that sector. The Bradford-field production in 1941 was 12,729,900 bbl. as compared with a production in the year 1940 of 12,748,279 bbl., or a reduction of 18,379 bbl. The year 1941 represents the fourth successive year in which production in the Bradford field has declined. All of the production from the Bradford field is obtained by water-flooding methods and increases or decreases in production are due more to economic factors than to any physical limitations of the pool, inasmuch as additional drilling of water-intake and producing wells would increase the total production of the field. It is apparent that increased drilling of oil and water-intake wells does not take place except under stimulps of a favorable price; and while oil prices during 1941 were moderately favorable, they were not sufficient to prevent a mild decline. Too many wells were drilled in the Bradford field in 1937, but this was compensated by subnormal drilling activities in 1938 and 1939 and a large increase in 1940, The increase in 1941 over 1940 was about 7 per cent. The effect of new drilling is becoming less pronounced on a per well basis because more properties yielding less per acre are being drilled than were drilled in former years. Central and Southern Pennsylvania The production in central and southern Pennsylvania amounted to a total of

Jan 1, 1942

By Arthur C. Simmons

The State of Pennsylvania produces approximately 60 per cent of the total production of Pennsylvania Grade oil, and naturally represents the dominant factor in the area producing that grade. The producing area comprises the states of New York, Pennsylvania, West Virginia, and a small part of Ohio. The importance of this area is too commonly neglected because it produces only 2 per cent of the total amount of crude produced in the United States. It is, of course, unimportant in its percentage of total crude production, but extremely important for its production of lubricating oil. The lubricating fraction from a barrel of Penllsylvania Grade crude oil represents about 22 per cent of the total, whereas the lubricating fraction from the total United States production represents only about 2.5 per cent of the crude oil. The Pennsylvania Grade area produces about 6,000,000 bbl. of lubricants, which is 15 to 20 per cent of the total produced in the United States. All Pennsylvania Grade lubricants are classified as "high-grade," and with a production of 15 to 20 per cent of the total lubricants, it appears probable that the Pennsylvania Grade area accounts for 25 to 50 per cent of the high-grade lubricants produccd in the United States. Production Bradford Field The production figures quoted in Table I apply only to the part of the Bradford held that lies wholly within the state of Pennsylvania; approximately 15 per cent of the Bradford field is in Cattaraugus County, New York, and 10 per cent of the production is obtained from that sector. The Bradford-field production in 1941 was 12,729,900 bbl. as compared with a production in the year 1940 of 12,748,279 bbl., or a reduction of 18,379 bbl. The year 1941 represents the fourth successive year in which production in the Bradford field has declined. All of the production from the Bradford field is obtained by water-flooding methods and increases or decreases in production are due more to economic factors than to any physical limitations of the pool, inasmuch as additional drilling of water-intake and producing wells would increase the total production of the field. It is apparent that increased drilling of oil and water-intake wells does not take place except under stimulps of a favorable price; and while oil prices during 1941 were moderately favorable, they were not sufficient to prevent a mild decline. Too many wells were drilled in the Bradford field in 1937, but this was compensated by subnormal drilling activities in 1938 and 1939 and a large increase in 1940, The increase in 1941 over 1940 was about 7 per cent. The effect of new drilling is becoming less pronounced on a per well basis because more properties yielding less per acre are being drilled than were drilled in former years. Central and Southern Pennsylvania The production in central and southern Pennsylvania amounted to a total of

Jan 1, 1942

By William H. Spice

The fault zone of south central Texas showed renewed activity during I940 along a trend roughly paralleling the old established Balcones fault-line group of producing fields. This was a result of the new discoveries in the Wilcox (Eocene) formation in southeastern Texas and Louisiana. As of the end of the year, one new field producing from the Wilcox formation had been discovered on the Washburn ranch in La Salle County, along the southwestern limits of the district, and several projected tests into that formation were under way. In the western part of the district, par-titularly in the part of the Rio Grande embayment that is in Dimmit, Webb and Zavala Counties, there has been renewed leasing activity with the shallower sands in the Navarro-Taylor formations (Upper Cretaceous) as the objective in several projected tests for the early part of 1941. Three new fields have been discovered along the old fault-line trend, but these have been comparatively small, producing either from Dale lime, Austin chalk or Buda lime. No new fields were discovered during the Year in the Edwards (Lower Cretaceous) lime horizon. Approximately 260 wells were drilled in the district during 1940, which resulted in four new oil fields. Twenty-seven new wells were completed in the Proven Edwards lime fields of Darst Creek, Luling and Salt Flat and seven were added to production in the Pearsall field. Approximately 160 wells in 18 counties were completed as failures during the year. The district produced 7,659,634 bbl. during 1940, which was a 9 per cent decrease under production for 1939. In all, 3559 wells were producing at the end of I940, compared with 3562 wells producing at the end of the previous year; 104 new producing wells were completed and 163 wells were abandoned in the producing fields of the district. During 1940 considerable exploratory work was carried on along the Wilcox trend within the district, particularly by major companies employing various types of geophysical methods, and leasing activity increased considerably. At the end of the year, the total number of acres of nonproducing leases held by major companies in the district increased about 10 per cent. It is anticipated that this activity will continue into the first part of 1941 and will be supplemented by several exploratory test wells. New Fields B,, Creek, Caldwett County.— . R. Ogden NO. 2 Talley, discovery well of the Bee Creek field, in the northeastern part of Caldwell County, was completed on March 16, I940, in Dale lime from 2091 to 2238 ft., pumping 85 bbl. per day, 39° A.P.1. gravity. The discovery of this field can be credited to a combination of subsurface geology and magnetometer work, which indicated the presence of a serpentine intrusion. At the end of the year, ,3 producing oil wells had been completed and the field has produced a total of 47,050 barrels.

Jan 1, 1941

By D. H. Polonis, J. G. Parr

IN a recent paper on titanium-rich Ti-Fe alloys,' the hardness of quenched powder specimens was given, together with the amounts of martensitic a they contained. The values disagreed in two respects with previous determinations that Worner² made on lump specimens: 1—Some martensitic a' is formed in powder specimens of alloys containing up to 12 atomic pct Fe. On the other hand, Worner reports that, although his results on quenched lumps are not conclusive, alloys containing more than about 4 pct Fe "appear to consist of retained ß'' although they "may not be strictly unaltered solid solutions." 2—According to Worner, quenched lump specimens show a maximum hardness at a composition about 3.5 pct Fe. Earlier -experiments by the authors showed a maximum hardness of martensitic alloys in powder form at 10 pct Fe. Accordingly, more experiments have been conducted in order to confirm these differences and to determine with more accuracy the minimum composition of quenched lump specimens that consist entirely of retained ß. Lump samples?x?x1/20 in. were quenched from 1000°C in helium and, on the whole, showed similar hardness values to the specimens that Worner water-quenched from 950°C. The hardness curve the authors obtained shows a more pronounced peak, but in other respects it is very similar to Worner's curve (Fig. 1). While it was possible to make fairly reliable measurements of the percentage of martensitic a in quenched powders (by Geiger spectrometer), the solid samples allowed only approximate estimates to be made from visual observation of line intensities on film. Retained ? begins to appear in quenched lumps containing 0.2 pct Fe; at 2.2 pct Fe there are approximately equal quantities of ß and a'; in a 4.7 pct Fe alloy only a trace of a' appears. These results are represented as a curve on Fig. 1. The hardness and constitution of powder samples were verified by repeating both types of quenching experiment described in the earlier paper.' Identical results were obtained by the two methods, and they agreed with the figures published previously (Fig. 1). The appearance of the martensitic structure under the microscope is shown in Figs. 2 and 3. The mar-tensite needles are coarser in the lump; otherwise the structures are similar. Three conclusions are made at this juncture: 1— The properties of quenched lumps reported by Worner are confirmed, on the whole. The differences between them and the properties of powders are probably due to an effect of specimen size. Differences of behavior in various sizes of specimen have been observed previously in martensite reactions in Fe-Mn alloys3 and in Cu-A1 alloys. 2—The maximum hardness of both quenched lumps and quenched powders appears at a composition where martensite formation has all but ceased. In this respect, powders and lumps behave similarly. 3—Martensitic a' has essentially the same microscopic appearance both in powders and lumps. Acknowledgment This work is part of a program sponsored by the Defegce Research Board of Canada, Project No. 425.

Jan 1, 1956

By C. R. Claus, G. A. Standish

Since March. 1945, the Magnolia Petroleum CO. has drilled 39 wells in Southwest Coastal Louisiana. All wells were drilled within a comparatively small radius, but the area provides a large variety of problems. The deepest well drilled was 13,518 ft, and the total depth averaged 10,977 ft. Throughout this period drilling mud control and types of mud handled were: (I) phosphate, (2) red lime (late conversion), (3) red lime starch (early conversion), (4) red lime starch oil emulsion, (5) precision controlled low alkalinity-low lime content. and (6) gel muds for completion purposes. Improvement has been obtained in effecting some or all of the following: (I) more rapid penetration, (2) reduction in drilling hazards, (3) better evaluation of cores and logs, and (4) better completions. The geological sequence of zones penetrated range from recent sediments at the grass roots through the Frio section. Anticipation of high-pressure zones and incompetent formations entails precision control of drilling mud weights, and the unconsolidated nature of the various zones requires constant attention to the filtrate, viscosity, and gel strength values. In the Chalkley field, particularly, this combination of problems exists, where the formation pressures and overburden weight density values are in very close proximity. Design of casing and drilling mud programs must be modified to fit each well. INTRODUCTION Field and research work on drilling fluids has made constant progress, enabling operators to prospect progressively deeper horizons. Numerous papers have been written on the theoretical aspects of drilling fluid devel- opment, but in the field engineers have found it difficult to evaluate the role of specific mud constitutents when dealing in terms of thousand barrel mud systems. For that reason field data is somewhat lagging in technical report writing. However, applications of new techniques in the field have usually paralleled, and in numerous instances preceded, research work. The information obtained by Magnolia Petroleum Co. in the course of drilling 39 wells within a comparatively small area in Southwest Coastal Louisiana provides an excellent opportunity of reviewing a specific example of drilling mud evolution. A large variety of problems has been coped with, the most important result being that every well was successfully drilled to its projected total depth. The discussion begins with the advent of deep drilling in this area in March, 1945, and is concluded with a resume of recent drilling operations in the Chalkley field. The primary purpose of this paper is to describe the evolution in types of drilling fluids as it occurred and its application in the solution of various drilling problems. All of this information and experience resulted in the successful drilling of the three wells in the Chalkley field, where a combination of the most sound techniques was necessary in carrying drilling operations to the projected total depths. Other operators along with service company engineers have contributed considerably through the interchange of ideas and information to this paper, but the data and conclusions which are contained are based on first-hand observation of Magnolia Petroleum Company's drilling operations. The 39 wells drilled by Magnolia Petroleum Co. average in depth 10,977 ft per well, while the maximum depth penetrated was 13,518 ft. The cost of drilling fluids have varied from $8,700 to $165,000, with the over-all drilling costs ranging from $74,000 to $543,000 per well. This wide variance illustrates the unpredictable nature of each well and the effects on over-all cost when high density muds are required to control

Jan 1, 1955

By P. E. Busby, C. Wells, M. E. Warga

Fundamental data on the rate of diffusion of boron in austenite and solubility of boron in the a and y phases of iron and steel have been obtained from deboronizing experiments and provide partial explanations for some of the phenomena observed in boron steels. The rate of diffusion of boron is about the same as carbon in austenite. The solubility of boron in austenite at normal heat-treating temperatures is less than 0.001 pct. A partial tentative Fe-B phase diagram in the important low boron concentration ranges and an equation representing the diffusion of boron in austenite are presented. A LTHOUGH a search of the literature revealed ALTHOUGHthat boron diffusion had not been studied quantitatively and systematically prior to 1948, a few qualitative observations which were made by following the diffusion of boron into iron packed in ferro-boron1-3 suggest that boron obeys normal diffusion laws and that the rate of diffusion increases with increasing temperature. The claim of Cornelius and Bollenrath1 that boron does not appear to influence the rate of carbon diffusion has recently been substantiated by Wells, Batz, and Mehl.4 Calculations based on data from the paper by Campbell and Fayv indicated that the diffusion coefficient (D) for boron in iron at 900°C is approximately 3x10 sq cm per sec; a value of 2x10-7 sq cm per sec at 1038°C has been reported by Digges et al in connection with decarburizing experiments on a commercial boron steel containing 0.43 pct C. During the period 1948 to 1950 several diffusivity constant (D) values for the diffusion of boron in the y phase of iron and steel and a number of solubility values for boron in both a and y phases were reported. It was concluded tentatively as a result of Metals Research Laboratory studies that D values for boron in y and a phases are about the same as for carbon in the comparable phasesa and that carbon up to 0.4 pct did not affect the rate of diffusion of boron in y iron above 1000°C within the limits of experimental error. Whether saturation of the y or a phases with carbon would significantly affect rates of diffusion of boron through them was then and still remains in doubt. The best estimate of Q (activation energy) was reported to be about 25,000 cal, somewhat lower than that for carbon in y iron. The solubility of boron in y iron at 1000°C was thought to be higher than 0.004 pct B but not as high as a more recent analysis of available data shows it to be. The solubility of boron in a iron at 700°C was reported to be 0.0004 pct B, but it would not have surprised the authors if the true solubility value is actually lower than this. Breaks in diffusion curves which were not understood when first obtained prior to 1950 have now been recognized as indicating solubility limits, and these are included in the present paper. Experimental Procedure Two methods were employed in an effort to determine diffusion coefficients (D) for boron in austenite. Early experiments involved the use of welded couples prepared in accordance with the procedure of Wells and Mehl,' but when the results of these experiments proved to be unsatisfactory for calculating D values, studies were continued by means of deboronizing experiments. In both cases, boron analyses following the diffusion anneal were carried out spectrographically and all D values were computed using the Grube solution of Fick's law. The precision of the spectrographic method used proved to be about equal to that reported by Corliss and Scribner" —average deviation from the mean about 5 pct of the amount present when the boron content is 0.003 pct. Concentration-penetration curves obtained from spectrographic analyses of welded couples generally indicated that practically no boron was transported across the weld interface during the diffusion anneal. Furthermore the concentration-penetration

Jan 1, 1954

By R. E. Ogilvie, A. R. Kaufmann, S. H. Gelles

The solid-solubility limits of iron in beryllium were determined between 850o and 1200oC by analysis of differential type multiphase diffusion couples, using an X-ray absorption technique. The maximum value of the solubility limit was found to be 0.92 ± 0.02 at. pct (5.46 wt pet) at the eutectic temperature 1225°C. The solubilities of nickel and beryllium were determined between 900°and 1200°C by the same technique and the maximum solubility was found to be 4.93 + 0.01 at. pct (25.2 wt pet) at the eutectoid temperature, 1065°C. A previously unreported high-temperature phase which decomposes eutectoidally at 1065 °C was found to exist in the beryllium-nickel system at a composition of approximately 8 at. pct Ni (36 wt pet) by diffision-couple analysis. The presence of this phase was confirmed by thermal analysis and metallo-graphic analysis of the structure resulting from the eutectoid decomposition. G. V. Raynor1 has treated the solid solubilities of some of the elements in beryllium on the basis of the "Hume-Rothery" rules2 which have been modified to include ionic size and ionic distortion effects. It was predicted that the solubility of iron and nickel in beryllium should be slightly less than that of copper. The lowering of the solubility, according to Raynor, is due to a more unfavorable relative valency effect and an ionic size effect. Kaufmann and corzine3 have compiled data on the solubilities of elements in beryllium and have discussed them in the light of the Raynor paper. These authors feel that, because the elements having the greatest solubility in beryllium systematically fall in the Group VIII and IB Columns of the periodic table, the electronic structure greatly influences the maximum solid solubility of elements in beryllium. The solubility of iron in beryllium was determined by Teitel and cohen4 as part of the study of the beryllium-iron phase diagram. The determination was carried out by X-ray and thermal analysis and according to the phase diagram presented, the maximum solubility of iron in beryllium is 0.41 at. pct (2.5 wt pct) at 1225oC. However, it is estimated that the uncertainty in the position of the a-beryllium primary solid-solution boundary is about 0.5 at. pct (3wtpct). Losana and Goria3 in studying the beryllium-nickel phase diagram, determined the solid solubility of nickel in beryllium by thermal analysis. They found the maximum solubility to be between 1.65 and 2.65 at. pct (10 to 15 wt pct) at 1240°C. This value decreased rapidly with decreasing temperature. In determining approximate ranges of solubilities for different elements in beryllium, Kaufmann, et al,8 reported a value of between 1.3 and 1.7 at. pct (7.9 to 10.1 wt pct) for the solubility of nickel in beryllium. The value was obtained by metallographic examination of quenched alloys and lattice-parameter measurements. However, the authors also noted a single-phase structure for a 1.7 at. pct Ni alloy (10 wt pct) on cooling from the liquid. This would indicate a higher solubility range than was reported. ~isch,' in his X-ray studies of beryllium-copper, beryllium-nickel, and beryllium-iron intermetallic compounds, reports the disappearance of a second phase (Ni,Be2) in the beryllium primary solid solution at approximately 4 at. pct (20 wt pct). THEORY The analysis of concentration gradients in diffusion couples has proven to be a useful tool in determining phase equilibria.8-14 In this particular study the diffusion couples were chosen to straddle the expected composition range of the phase boundary, then heat treated at a given temperature and the concentration gradient evaluated. The composition of the phase boundary for a given temperature appears at a point of discontinuity of the composition gradient. Examples of typical phase diagrams and the concentration gradients which should be found in such systems are shown in Fig. 1. In the present work, gradients of the form of Fig. l(c) were obtained in diffusion couples made of pure beryllium and two-phase alloys of beryllium with either iron or nickel. The composition at the point where the gradient becomes discontinuous, Cs, corresponds to the solubility limit of either iron or nickel in beryllium. The analysis of the concentration gradients was carried out by an X-ra absorption method developed and applied by Ogilvie and later used by Moll13 and Hilliard.l4 It depends on the fact that the absorption of X-rays by matter is determined by the concentration and type of the various atomic species present. The relationship for the intensity, I, of a monochro-

Jan 1, 1960

By S. R. Goodman, Hsun Hu

A detailed study of texture developmenf in poly crystalline copper atzd 70-30 brass has been completed. Textural changes as a function of deformation are shoum by pole jigmres and by intensity measurements oF- various rejlectiotzs from the rolling plane and the rolling direction. These examinations were accompanied by measurements of stacking fault frequency, hardness changes, and microstructure. Some of the results were briefly presented earlier. Additional results reported here are consistent with the idea that deformation faulting or slip by partial dislocations is of primary importance in the formation of deformation textures in fcc metals. lo examine the idea that deformation faulting is of primary importance in determining whether the texture is the copper type or the brass type an extensive study of the development of polycrystalline textures in copper and 70-30 brass was initiated. Besides the determination of complete pole figures, the intensities of the various reflections from both the rolling plane and the plane perpendicular to the rolling direction, the peak shifts due to deformation stacking faults, and the hardness of the rolled specimens were examined at various reductions from 10 to 99 or 99.5 pct. Mi-crostructures were examined by transmission electron microscopy. Some of the results were briefly presented in an earlier publication.' Since then, additional information has been obtained. This is given in the present paper. EXPERIMENTAL PROCEDURE Material and Specimen Preparation. The material used was a commercial electrolytic copper bar 1i in. wide and 2 in. thick and a 70-30 brass bar la in. wide and 1i in. thick. Chemical analysis indicated a purity of 99.97 pct for the copper, with 0.025 pct 0 as the major impurity. The 70-30 brass was of higher purity with 0.0016 pct 0 as the major impurity. Extreme care was taken in the preparation of the starting material to insure uniformly fine grains with a nearly random initial texture. The two bars were first cold-forged and then annealed to eliminate any original texture. The grains were then refined by several cold rolling (approx 30 pct reduction) and annealing treatments. The + -hr anneals were carried out in a salt bath at 390" to 440°C for copper and at 490°C for brass. The resulting penultimate grain size was 0.06 mm for copper and 0.03 mm for brass, and both showed very little preferred orientation. The number of prior cold rolling and annealing cycles was such that the final thickness after various final reductions of 10 to 95 (for brass) or 99 (for copper) pct was the same (0.020 in.). These annealed strips were rolled in two directions by reversing end for end between passes according to the following schedule: 0.006 in. per pass to 0.100 in., 0.003 in. per pass to 0.050 in., 0.002 in. per pass to 0.025 in., 0.001 in. per pass to 0.020 in. Texture Determination. The development of rolling textures was studied by examining complete pole figures determined from the (111) reflection. Specimens thinned from one face of the strip to half thickness (0.010 in.) were used to obtain the central portion of the pole figures, while specimens thinned from both faces to 0.003 in. were used to obtain the peripheral portion. The reflection and transmission techniques have been described previously. In addition to X-rav pole figures, texture development was also studied b; examining the intensity variation of the (Ill), (200), (2201, (311), (331), (420), and (442) reflections from the rolling plane and from the plane normal to the rolling direction, as a function of deformation. The same specimens used for the central portion of the pole figures were used for the intensity measurements of the various reflections from the rolling plane. For intensity measurements from the plane normal to the rolling direction, composite specimens were prepared by mounting sections cut parallel to the transverse direction of the strip. An epoxy resin was used to bond these sections together, and the entire composite was then mounted in a cold-setting resin to facilitate subsequent polishing and etching to remove distorted metal at the cut. The intensities were expressed in units of the integrated intensities measured from an annealed copper specimen having almost no preferred orientation. Stacking Fault Frequency Determination. Following the analysis of Warren: the stacking fault frequency, a, was determined from the change in the peak separation (A%) of two neighboring reflections of a deformed specimen, as compared with the normal peak separations of a fully annealed specimen. To obtain sufficient intensities for the second-order reflections, (222) and (400), composite specimens were prepared from parallel sections cut from the strip at 30 deg to the rolling direction for copper and 25 deg for the brass.* From texture data, these sections are known to contain a large population of both (111) and (200) planes. Since residual stresses can also cause X-ray line shifts (the direction of line shifts depends upon the sign of the stress), the use of composite specimens consisting of sectioned planes should help compensate for these effects as the residual stresses change sign from the surface to the central section of a rolled strip. Since the amount of peak shift is almost un-measurable in brass rolled 15 pct and in copper rolled

Jan 1, 1969

By C. S. Sivaramakrishnan, Manjit Singh, Rajendra Kumar

Regarding liquid nzetals structurally as a suspm-sion of clusters , having derivated solid-state coordination, in truly liquid atoms, the recently developed Kuvlar-Samarin technique of centrifuging- in liquid state enabled the determination of the cluster sizes inAl-Cu mid Pb-Sn systems. It is shown that the colutne fraction of the clusters does not exceed 9 pct and the energy of their formation in Al-Cu is about 5.5 kcal per g-atom and in Pb-Sn eutectic alloys about 25 kcal per y-atoni. STRUCTURAL investigations of liquid state have principally followed the following three courses: i) studies with X-ray, electron, or neutron diffraction; these investigations have shown that there is a certain amount of regularity in the structure of liquid metals which can be defined by a coordination number and that the structure is a derived function of that in the solid state; ii) thermodynamical investigations which are based on the concept of ideal behavior; these describe the liquid state in terms of free-energy values and other thermodynamic functions; although these investigations are of help in the study of the general effects of alloying, they do not provide any structural insight into the precise atomic distribution in liquid state; iii) measurements of surface tension and viscosity; although it is natural to expect that the viscosity is related to the structure in liquid state, these investigations have so far only provided information which can be used by the foundry technologists and has been little utilized in formulating models of the structure of liquid state. As it happens, investigators in the three groups have worked almost independently of each other and there is practically no structural correlation between the results of one group with those of another. The purpose of the present paper is to indicate that the experimentally measured parameters of these three groups of research are closely related to the structure in the liquid state. STRUCTURE OF LIQUID METALS Although atomic distribution in solid and gaseous states is rigorously known, that of the liquid state is only appreciated on the fringes. There is no universal model of atomic distribution in liquid state, but two diverse models are at present hotly contested. The first, largely expounded by ~ildebrand,' regards the liquids as condensed gas since many of their properties and much of their behavior can be adequately described by regarding them as fluids. The second mode12j3 considers that some form of near-solid as- sociation of large number of atoms exists in the liquid state. On the other hand, ~ernal' was able to predict rather precisely the radial distribution functions in liquids on the basis of statistical geometric approach which considered that liquids are "homogeneous, coherent, and essentially irregular assemblage of molecules containing no crystalline regions or holes large enough to admit another molecule". He introduced the concept of pseudonuclei in the otherwise random structure as aggregates of closely packed tetrahedra which gradually merge into irregularity and continually replace each other. To what extent the pseudonuclei can be regarded as regions of near-solid association is indefinite but Bernal suggested that the concept of pseudonuclei can be compromised with the latter model if the near-solid associations are regarded as extremely dense and not necessarily crystalline. The difficulty in projecting the structure of liquid metals arises because they exhibit duplicity of character as some of their properties are closer to those of crystalline solids and others to fluids. There is an increasing tendency to discuss the structure of liquid metals in terms of the second concept according to which the structure of liquid metals may be conceived as consisting of i) clusters of atoms where the aggregation is a close derivative of that in the crystalline state, ii) individual atoms which behave like true liquids in respect to degrees of freedom and iii) excess number of vacancies. It is noteworthy that the introduction of only 5 pct vacancies is sufficient to transform crystalline matter into the liquid state. At any instant of time thermodynamic equilibrium exists between i, ii, and iii, but the relative proportion of the clusters and random atoms is not known. That this is so can be appreciated by the fact that, when liquid metal is rapidly cooled, liquid state vacancies may condense in the form of dislocation loops and vacancies in excess of their equilibrium number in solid state. These dislocation loops have been observed in thin foils of aluminum prepared from rapid cooled aluminum. As temperature increases above melting point the number and volume fraction of clusters decrease but those of vacancies and random atoms increase. Clusters are transient in nature. In pure metals the cluster is an aggregation of the metal itself. In alloys, however, the nature of the cluster largely depends on the interaction between solvent and solute atoms. If the interaction between unlike atoms is greater than between like atoms: the clusters are then aggregates of unlike atoms. Examples of this kind of system are A1-Cu, Mg-Pb, and so forth, i.e., systems which exhibit negative departures from the Raoult's law. In systems where the interaction between unlike atoms is smaller than be-

Jan 1, 1968

By M. J. Marcinkowski, Gordon E. Lakso

An extensive investigation has been made of the deformation behavior associated with the Fe3Si super-lattice using transmission electron microscopy techniques. Above 243°K the stress-strain curve exhibits three stages. Stage I occurs at a very low stress level and is related to the generation of perfect superlat-tice dislocations. Stage II is characterized by an extremely rapid rate of work hardening and is associated with the Taylor type locking of these superlattice dislocations. Finally Stage III is related to dynamic recovery processes since the work hardening rate is very small. Below 243ºK, only Stage I is observed, but it occurs at a much higher stress level. This latter observation is related to the generation of imperfect dislocations in Stage I with the consequent production of second nearest neighbor antiphase boundaries. The reason for this is that insufficient thermal energy is available at these low temperatures to generate the complete and perfect superlattice dislocations. It has been shown that the fully ordered FeCo alloys, i.e., those possessing the B2 type structure, exhibit three distinct stages of work hardening whereas the corresponding disordered alloys show only one.&apos;" This difference in behavior between the disordered and ordered alloys has been attributed to the fact that dislocations in the former case travel only as ordinary 1/2ao(111) types whereas in the latter case the move through the lattice as coupled 1/2a0(111) dislocations separated by an antiphase boundary (APB), i.e., the so-called superlattice dislocation. Although some preliminary work has been carried out concerning plastic deformation in ordered alloys possessing the DO3 type superlattice,3 no detailed analysis similar to that described in Refs. 1 and 2 has been attempted. Specifically, it has been suggested that the superlattice dislocation in this particular type structure should consist of four ordinary 1/2ao<111> types bound together by first and second nearest-neighbor APB&apos;s. Fe3A1 and Fe3Si are the two classic alloys possessing the DO3 type lattice; however, because of the somewhat higher ordering energies associated with the FesSi alloy, which in turn assures that dislocations will travel through the lattice as perfect superlattice dislocations under at least some conditions, it was chosen for the present investigation. Because of the extreme brittleness of Fe3Si, all deformation was done in compression. Stress-strain curves were obtained using both polycrystalline samples as well as single crystals. In the latter case the crystals were oriented so that deformation could be controlled either by single or double slip. They were then wafered parallel to and at various angles to the operative slip planes. These wafers were in turn examined by transmission electron microscopy (TEM) techniques in order to determine the extent of the interaction from the dislocation configuration contained therein. EXPERIMENTAL PROCEDURE The alloys used in this investigation were arc melted under helium from electrolytic iron of greater than 99.90 wt pct purity and transistor grade silicon of 99.99 wt pct purity. A typical analysis of interstitial impurities showed 120 ppm 0, 15 ppm N, and 65 ppm C Because of the extremely low ductility of the Fe3Si alloys, it was necessary to spark cut 0.230-in. diam polycrystalline cylinders 0.400 in. long from arc-melted fingers using a thin-walled brass tube as a cutting tool. The polycrystalline alloys could not be recrystallized since very little strain was induced in preparation. However they were annealed at 1273°C for 15 min in evacuated vycor capsules to relieve any cooling stresses that may have developed during solidification and then air cooled. The resulting grain size of the alloy was 0.50 mm. According to warlimont4 1273ºC is just within the single phase field where FesSi possesses the DO3 type lattice. In addition because of this high critical ordering tem-ature, air cooling from this temperature was believed sufficient to fully order all of the Fe3Si samples used in the present investigation. For the same reason, no attempt was made to achieve any degree of disorder by quenching. In fact, rapid quenching from 1123°K caused cracking. Such cracking was first suggested by sato5 with respect to the experimental observations of Glaser and Ivanick.6 Single crystal compression specimens were spark cut from single crystal ingots grown in a Bridgman type furnace. The iron and silicon for the crystals was prealloyed by arc-melting two 130-g buttons which were cut into small pieces before remelting in the furnace. This procedure resulted in a long-range inhomogeneity of 0.5 at. pct Si between the top and bottom of the 2-in.-long single crystal ingot, which was assumed to be negligible in the present investigation. The single crystals, after orienting and spark-cutting, were about 0.37 in. by 0.37 in. in cross section and about 0.5 in. long. True stress-strain curves were obtained using an Instron Tensile Testing machine in conjunction with techniques described previously. 1,7 The strain rate was 0.05 in. per in. per min. Prior to testing, the ends of all the compression cylinders were hand polished using a special jig to insure parallelism after which the sides of the samples were electrochemically polished to eliminate stress risers and to facilitate slip line observations. Test temperatures between 77" and 823°K were obtained using various cooling and heating media as described in Ref. 7 while at the upper end of this temperature range, a mixture of equal

Jan 1, 1970

By W. O. Hotchkiss

DURING the summer of 1927, the Department of Terrestrial Magnetism of the Carnegie Institution of Washington joined with the Michigan College of Mining and Technology in conducting a series of earth-resistivity measurements in the Michigan copper country. The geological structure in this section is quite varied and fairly well known. The purpose of the investigation was to discover the correlation between the variations in electrical resistivity of large masses of soil and rock in place and the geological structure below the surface. The work done may be roughly divided into two parts: (1) Measurement and study of the variations in resistivity with depth, or with volume, to establish such general relations as exist between the two: and (2) the determination of the specific resistivity of various formations in order to make available more fundamental data which may aid in the interpretation of the results of the former type of measurement. A report by Mr. Rooney, which gives in detail the measurements made and the results obtained, forms the basis for this article.

Jan 1, 1928

By A. C. Heath, E. H. Dix

THE importance of aluminum-silicon alloys in the light alloy field is now generally recognized. Where silicon was once considered detrimental to the properties of aluminum, useful alloys now contain as much as 13 per cent. Furthermore, silicon is present as an impurity in aluminum of even the purest grades. Iron is another important impurity in aluminum and like silicon is found in small quantities in the purest aluminum available today. The manner of occurrence of iron and silicon in commercially pure aluminum and many of its alloys exerts a very pronounced influence upon their properties. The effect of large quantities of iron in aluminum-silicon alloys is so detrimental that it has been found necessary to limit the allowable maximum percentage to as low a figure as is consistent with quantity production and satisfactory physical properties. The intimate relation existing between iron and silicon in aluminum and aluminum alloys makes necessary a more complete knowledge of this ternary system. This paper is divided into two principal parts, dealing respectively with aluminum-silicon solubility equilibria and the constitution of aluminum-iron-silicon alloys. PART I.-ALUMINUM-SILICON ALLOYS The early work on this system was largely confined to determining the general form of the diagram and in this respect the results are in good agreement. Briefly, aluminum and silicon form a simple eutectiferous series without compounds. Until recently the solid solubility of silicon in aluminum had not been accurately determined. Fraenkel1 (1908) stated that aluminum will retain 0.5 per cent. silicon in solid solution. Rosenhain, Archbutt and Hanson2 gave the maximum solubility as about 1.50 per cent. and added that "this solubility does not appear

Jan 1, 1928

By G. Hileman

During the year 1934 there were no new or extraordinary developments in the proven fields. With few exceptions all companies operating in these fields continued intensive exploitation programs on their old properties in an attempt to maintain the normal production of former years. In one or two instances these exploitation activities have had such marked success that the total production for 1934 slightly surpassed that of 1933. The most striking increase in production is that shown by the Kilometer 27 pool of the Comodoro Rivadavia field. However, this increase cannot be attributed to intensive drilling, since it is the result of a more uniform daily withdrawal distributed among all the productive wells. The Province of Salta also showed another increase, so that, judging from the statistics of the past three years and in view of proposed exploration projects, the future may reveal some interesting developments in this province. One of the most interesting occurrences in Salta is the discovery, though not yet considered commercial, made at Macueta, near the boundary line between the Argentine and Bolivia. This exploration well was drilled by the Standard Oil Co. of New Jersey and is the northernmost exploratory well in the republic. The oil from this well is of the same type and commercial value as that produced in the San Pedro and Lomitas fields. The producing horizon is also the same as that in the other Salta fields; that is, the Paleozoic Permo-Carboniferous.

Jan 1, 1935

By R. P. Agarwala, M. S. Anand, S. P. Murarka

Using the residual radioactivity technique, grain boundary diffusion of chromium in the a phase and lattice diffusion in the a and the ß phases of zirconiuttz have heen studied. The diffusivities (in units of square centiwzeters per second) have heen expressed as THE rate of diffusion of atoms along surfaces and grain boundaries is much greater than that through the bulk of metals. These processes dominate over volume diffusion at lower temperatures and can be isolated from it by virtue of the fact they yield high diffusion coefficients and low activation energies. In zirconium, however, it has been difficult to identify the volume-diffusion parameters separately. The values of diffusivities in a and ß phases yield activation energies which are much lower than those for volume diffusion calculated from semiempirical or empirical relations.1-3 Diffusion frequencies (Do) are also low, especially in the a phase, and they yield negative entropies of activation.4 Similar results have been obtained for the diffusion studies in titanium.5 It is yet to be investigated whether in these cases diffusion is controlled by some extraneous factor like high reactivity of these metals, or some different mechanism is operative as suggested by Pound et a1.6 However, Federer and Lundy,7 in a recent study of the diffusion of zir-conium-95 and columbium-95 in zirconium, and Gibbs et al.,8 in the study of impurity diffusion in titanium, found a temperature dependence of D, Do, and Q. Their study yielded low values of Do and Q at low temperatures, as has been found by other workers, and fairly high values at high tempera-

Jan 1, 1965

By T. O. King, Y. P. Gupta

The self-diffusion of sodium in two sodium silicate liquids was measured in the temperature range 850" to 1500°C by the capillary-reservoir technique. Radioactive Na 22 was used as the tracer. The total count and autoradiographic methods were used for determination of the total Na 22 depletion and diffusion profiles of the dqy-used specimens. The diffusion coefficients obtained by the autoradiographic technique are slightly smaller than those obtained by a total count method. Error analysis of the two methods suggests that more confidence be placed in the results of the total count method. The experimental results were analyzed in terms of the existing activated rate process theory. The activation energy for diffusion was shown to decrease markedly as the temperature increased. This was attributed to a variation in the heat of activation with temperature, probably related to a change in the distribution of anions associated wilh the cation. In terms of a model, suggested for diffusion in liquid silicates, differences in the aclivation energies for diffusion and electrical conduction may arise from the effect of the electric field applied in conduction measurements. It is generally accepted that liquid silicates consist of cations and an equilibrium distribution of complex anions determined by temperature and composition. Transport properties in molten silicates are of interest, not merely because of their relevance to the kinetics of pyrometallurgical reactions and glassmak-ing processes, but also because they are useful to development of the theory of such ionic liquids. Self-diffusion is one such transport process that may, if studied for liquid silicates of widely varying compositions, indicate structural changes through changes in the activation energy for diffusion. The self-diffusion of calcium, silicon,&apos; sulfur: aluminum, 4 and oxygenS in lime-alumina-silica melts and of iron6 in molten iron silicates have been measured. Unfortunately, the errors in some of the reported activation energies for diffusion are too large to allow firm conclusions concerning structure and the mechanism of the diffusion process to be drawn. The research reported here was a study of the self-diffusion of sodium in liquid sodium silicates. The soda-silica system was chosen since: i) a reasonable composition range can be covered in the binary system at moderate temperatures; ii) suitable isotopes of sodium (radioactive Na 22 and NaZ4) can be obtained; iii) data on the electrical conductivity and viscosity of sodium silicate liquids are available. However, the range of composition actually used in diffusion experiments was limited, to 20 to 35 wt pct soda, by the relatively high viscosity of silica-rich compositions and by evaporation of soda from basic melts. EXPERIMENTAL PROCEDURE The capillary-reservoir technique was used, wherein a radioactive tracer, Na 22, incorporated in the capillary melt, was allowed to diffuse out of the platinum capillary tube into a large reservoir of silicate liquid containing a chemically identical melt, but without radioactive tracer. After a specific diffusion time, both the total depletion in the tracer concentration and concentration-distance profiles of the diffused samples were measured by procedures to be described later. The diffusion cell assembly was similar to that used by Koros and King.&apos; The temperature of the diffusion cell was measured with a calibrated Pt, Pt-10 pct Rh thermocouple located at the center of the liquid reservoir. The same thermocouple was used to obtain the temperature profile in the reservoir. The temperature at the top of the reservoir was slightly higher (2°C) than that at the bottom, to minimize convection in the capillary tubes, which were placed, open end up, in the reservoir. Convection was not expected to be a problem since the length-to-diameter ratio of the tubes was about 12:1 and the maximum capillary diameter was 1 mm. The diffusion cell was heated in a molybdenum-wire resistance furnace, previously used by Koros and King, but somewhat modified. A Pt, Pt-10 pct Rh thermocouple enclosed in an alumina tube and located near the furnace winding was used in conjunction with a preamplifier and Micromax proportional controller for temperature control, within 4°C, at temperatures near 1500°C. Before starting a diffusion run, the furnace was heated to the desired temperature and an alumina guide assembly for the capillaries was slowly lowered to within 2 cm of the liquid reservoir. The capillaries were thus heated to about the temperature of the bath. The run was started by lowering the assembly till the open ends of the capillaries were about 1 cm below the surface of the liquid. The run was ended by raising the assembly to about 15 cm above the liquid bath. Later, the sample assembly was slowly withdrawn from the furnace. Six diffusion samples were usually run at the same time. Three runs made with the open ends of the capillaries down were discarded because in the majority of these samples air bubbles trapped at the open end were observed. Some glass adhered to the outside of the capillary on withdrawal. This was carefully removed and used to check that the Na 22 activity in the sink remained at a low level. Materials. Nonradioactive sodium silicates were prepared by melting, in a platinum crucible, weighed quantities of sodium carbonate and powdered silica. To prepare radioactive sodium silicates, Na2 obtained in HC1 solution, was first checked for radioactive impurities by obtaining a y-ray energy spectrum, then the chloride ions were removed by anion-ex-

Jan 1, 1968

By G. W. Neighbor, M. S. Abrahams

The actice slip plane in InSb is found to be of the {111} type by using the method of two-tmce anulysis. Measurements of the rotation of the tensile axis with increasing plastic shear strain indicate that the tnacroscopic slip direction is a <110>. Recrystal-lization is first observed at a sheav strain of about 70 pct for a crystal deformed at a temperatzcre of 473° C and at a shear strain rate of 2.90 times 10- %ecc-I; the dislocation density corresponding to this value of the strain is 1 x 108 em-&apos;. At a shear strain of about 170 pct, the recrystallization process is complete. This appears to be the fimt time re-crystallization has heen observed in a semiconductor. V HE operation of the {Hi} glide plane in Ge was first noted by Gallagher.&apos; This finding was confirmed by Treuting who also extended the result to Si. Using X-ray techniques, Treuting3 demonstrated that the macroscopic slip direction in Ge was of the <110> type. The choice of the (111) <110> slip system in Ge is exected since in the diamond-type structure the {Ill7 plane is the plane of highest density and the <110> direction is the direction of closest packing.4 There is little reason to expect that the glide elements of InSb are different from those of Ge, since the zinc-blende structure characteristic of InSb is quite similar to the structure of Ge. With regard to InSb, Allen5 has indicated that the glide plane is the {111} type. There appears to be no quantitative determination of the glide direction, however. The present work was undertaken to establish both the glide plane and glide direction in InSb and also to see if recrystallization occurs at large shear strains. EXPERIMENTAL PROCEDURE Mechanical Deformation. The single crystals of InSb used in this investigation were deformed in uni-axial tension. The tensile axis of the specimens was [145] and the periphery was bounded by (111) and (321) planes as shown in Fig. 1. The metallographi-cally polished specimens were deformed in a dynamic atmosphere of He, using an Instron machine. The tensile tests were performed at temperatures in the range of 300°C to the melting point (525OC) and at shear strain-rates varying between 1.94 X 104 sec-&apos; to 1.94 x 103 sec-&apos;. Additional details concerning the preparation and deformation of the specimens have been presented previously.&apos; Analysis of the Glide Elements. The traces of the active slip plane in both (111) and (321) planes were analyzed according to the usual method of two-trace analysis." The macroscopic slip direction was determined by measuring the rotation of the tensile axis as a function of plastic strain,8 These measurements were made from Laue back-reflection X-ray photographs. The X-ray beam was perpendicular to the (111) plane. A given crystal was used for only one measurement of the rotation of the tensile axis after it had been strained to a predetermined value. Therefore, care was taken at all times to insure that the X-ray beam was parallel to the [Ill ] direction of all the samples. RESULTS AND DISCUSSION Glide Plane. After 3.4 pct plastic shear-strain, at a temperature of 369°C and a shear strain-rate of 1.94 x 104 sec-&apos;, the slip traces on the (111) and (3.21) planes appear as in Figs. 2(a) and 2(b), respectively. The results of an analysis of these glide markings demonstrate that the slip plane is (111). The operation of this plane is expected on the basis of the orientation of the specimen, since glide on this plane and in the [I011 direction will result in

Jan 1, 1962

By W. F. Chiao

Ultrasonic attenuation, a, measurements in the frequency range of 5 to 55 mc per sec have been studied to determine their quantitative relationship with the following three variables of mixed microstructures in steels: 1) the volume percent, XF, of polygonal fer-rite in mixed structures of martensite and polygonal ferrite in Fe-Mo-B alloys: 2) volume percent, XA, of retained austenite plus martensite aggregates in high-carbon steel; and 3) substructural differences between 100 pct bainitic ferrite structures formed at various temperatures. The quantitative relationship obtained in the first two conditions by plotting a us the known structural parameters can be expressed, respectively, as: where al, a 2 and C1, Cz are constants. In the third condition the nature of the attenuation depends on the state of dislocations generated at the transformation temperatures and also on the alloy composition. From these measured results, the mechanism of ultrasonic attenuation caused by these mixed microstructures can also be studied. MUCH interest has recently been shown in the application of ultrasonic attenuation and wave velocity measurements to the study of the microstructural characteristics of steels. The general aims of most of the investigations in this field can be grouped into two categories: one is to study the mechanisms of ultrasonic losses caused by the characteristic phases in the microstructure of steel,&apos;&apos;&apos; and the other is to develop nondestructive test methods and applications for quality control.~&apos; 4 Apparently no work has been done on the evaluation of ultrasonic attenuation meas -urements as a means of quantitative determination of a given phase in the microstructure of a steel. It is well-established that the decomposition of austenite results in four main microstructural constituents—polygonal ferrite, pearlite, bainite, and martensite—and that each phase has different mechanical properties. Thus, when a steel consists of mixed microstructures, the mechanical properties can often be related to a quantitative measure of the volume percent of each phase present. This study relates ultrasonic attenuation measurements to: 1) the volume percent of polygonal ferrite in mixtures of martensite and polygonal ferrite in Fe-Mo-B alloys; 2) the substructural differences between 100 pct bainitic ferrite structures formed at various temperatures; and 3) the vol- ume percent of austenite in austenite plus martensite aggregates in a high-carbon steel. The choice of the specimen materials was based on the laboratory stocks which were suitable to produce the required mixed microstructures for this study. EXPERIMENTAL PROCEDURES Materials and Heat Treatment. Polygonal Ferrite Plus Martensite Structures. This mixture of phases was produced in a vacuum-melted Fe-Mo-B alloy. The alloy was hammer-forged at 1900" ~ to a -f-in.-sq bar. By isothermally heat treating the alloy at 1300° F for various times and then water quenching, variations in the amount of polygonal (or proeutectoid) ferrite can be controlled in a microstructure in which the balance of the material is martensite. In the present work, four different times of isothermal transformation were adopted; after heat treatment, the four specimens were machined for ultrasonic measurements. The compositions, heat treatments, and dimensions of the four specimens are listed in Table I. 100 pct Bainite Structures Formed at Different Temperatures. It has been well-established by Irvine et al.= that the presence of molybdenum and boron in ferrous alloys can retard the formation of polygonal proeutectoid ferrite and expose the bainitic transformation bay, so that a more acicular or bainitic ferrite can be obtained over a wide range of cooling rates. Their investigation6 also showed that the mechanical properties of fully bainitic steels are usually closely dependent on the substructural characteristics of the steels. For studying the substructural characteristics in completely bainitic structures, six Fe-Ni-Mo alloys, of which five were free from carbon addition and one with 0.055 pct C addition, were selected so that a wide range of hardness values for 100 pct bainitic ferrite structures could be produced by normalizing at 1900" F followed by air cooling. The different bainitic transformation temperatures were recorded during air cooling. All of the alloys were vacuum-melted and then forged at 1900" F to square bars. Data on the six specimens of these structure series are summarized in Table 11. Austenite Plus Martensite Structures. The high-carbon steel used to study austenite plus martensite structures was vacuum-melted and then forged into Q-in.-sq bar. The series of mixed structures of austenite plus martensite was produced by quenching the specimens from the austenitizing temperature to room temperature and then refrigerating them at various temperatures within the range of martensite transformation to produce different amounts of retained austenite. Data on the four specimens of this series are listed in Table 111. Quantitative Analysis of the Microstructures. The microstructures containing martensite plus polygonal ferrite were analyzed by the point-counting technique.

Jan 1, 1969

By J. J. Gilman, T. A. Read

FOLLOWING the deformation 01 zinc monocrys-tals, sharply bent basal planes are observed near several types of inhomogeneities. Three of these in-homogeneities have characteristics which are quite regular so that they can be studied and analyzed. These are compressive kink bands, "deformation bands," and the inhomogeneities near end restraints. The present paper describes experiments in which "deformation bands" were artificially produced, and bend plane phenomena are discussed in terms of dislocation theory. Also, two new bend plane phenomena are described. The importance of bend plane phenomena in the deformation of crystals is not widely recognized. Many phenomena may be explained in a manner similar to the discussion in this paper. Jillson1 has pointed out that the "punching effect" in zinc is a bend plane phenomenon and is not caused by prismatic slip.&apos; Bowles3 has suggested that they may be involved in diffusionless phase changes. Cahn4 has discussed the role of bend plane formation in the polygonization of zinc. Experimental Work Tensile Kink Bands: Because of the geometrical similarity between "deformation bands" and "kink bands" (compare Fig. 1 of this paper with Fig. 1 of the paper by Hess and Barrett"), the band shown in Fig. 1 of this paper will be called a "tensile kink band," and that shown by Hess and Barrett will be called a "compressive kink band." It is felt that the term "deformation band" should be reserved for banded structures in polycrystalline materials such as iron." Tensile kink bands seem to form spontaneously in aluminum crystals deformed by tensile loading.7-10 In zinc and cadmium crystals they do not form in good, carefully loaded specimens.&apos;." However, tensile kink bands can be produced artificially in zinc crystals. The present authors did this by scratching one of the flat surfaces of triangular crystals transversely with a sharp needle. Natural tensile kink bands caused by inhomogeneities sometimes appeared in deformed crystals which were identical in appearance with the artificially produced ones. Zinc monocrystals were grown by the Bridgman method in graphite molds. Chemically pure zinc (99.999+ pct Zn) was used and the molds were sealed inside evacuated pyrex tubes during growth. The crystal cross sections were equilateral triangles with a typical base of 0.210 in. The artificial kink band shown in Fig. 1 is typical of tensile kink bands in zinc. The band lies between two bend planes which run from upper right to lower left and is inclined oppositely to the slip bands which are sharply bent at the two bend planes. The general form of the artificial tensile kink bands was independent of the scratch depth (1 to 5 mils deep) and also independent of which side was scratched. These variables did cause variations, however. Deep scratches produced more localized kink bands than light scratches. Also, if the angle between the slip plane traces and a transverse scratch varied appreciably among the three sides, then localization of the resulting kink bands also varied. Furthermore, if the slip direction lay nearly parallel to the scratched side, the band was more developed near the scratched side than at the opposite edge. Scratches produced tensile kink bands for crystal orientations from xo = 15" to x, = 75". Fig. 2 shows a scratched crystal after deformation. One triangular side lies in the plane of the photograph. The right hand tensile kink band was produced by a transverse scratch on the upper right side. The next two kink bands were the result of scratches on the front surface. The kink band at the left was caused by a scratch on the lower back side. All four bands have the same general form. A longitudinal scratch was also made on the crystal shown in Fig. 2 to determine the effect of a scratch on the critical shear stress. The critical shear stress of the scratched region was 33.9 g per sq mm compared to 24.4 g per sq mm for the un-scratched region above it. Fig. 3 shows Laue patterns of the crystal shown in Fig. 2. Fig. 3a shows the pattern of the undeformed crystal. The orientation was x, = 21°, A, = 31". After deformation, Fig. 3b was made of the homogeneously deformed portion of the crystal. The spots are compact but split into two halves. This region was elongated 45 pct and its orientation was x = 14", X = 20"; the sine law predicts x = 14", A = 20.5". Fig. 3c was taken near the center of the middle tensile kink band of Fig. 2. The pattern shows a range of orientations and polygonization in this region. The spread in orientation was due to the fact that the basal planes were curved (see Fig. 1) rather than flat as in the ideal case. Some may also have been the result of elastic distortions and "local curvatures." The orientation range was x = 23" to 32", A = 30" to 42". It is apparent from Fig. 3 that the material inside and outside the kink band rotated in opposite directions with respect to the tension axis during deformation. The orientation calculated from the ideal configuration of Fig. 9,

Jan 1, 1954

By R. A. Salathiel, A. D. Kaiser, P. H. Monaghan, B. E. Morgan

The productivities of many hydrocarbon-bearing for-rnntions appear to be reduced during drilling, completing and repairing operations. The reason for these othcarwise unexplainable low productivities may be a drastic reduction of formation permeability immediately surrounding the borehole. A possible cause of the reduced permeability is swelling and dispersion of clays present in porous media when contacted by fresh water or mud filtrates. Hence, the invasion of fresh water or mud filtrate into hydrocarbon-bearing formations that contain clays may cause low productivities as a result of formation damage. Present laboratory investigations have yielded results which supplement existing literature on formation damage. An expanded-type clay, montmorillonite, way found in hydrocarbon-bearing formations not previously analyzed. When sand columns and formation cores containing montmorillonite were contacted by fresh water, their oil permeabilities were reduced. This reduction in oil permeability way restored partially but not completely by a repair procedure, i.e., flooding with kerosene containing organic agents or flooding with water containing electrolytes. Hence, where montmorillonite is present in formations, prevention of formation danzage was indicated to be the only complete solution to the problem. To prevernt formation damage, results suggested use of an approximately 1 per cent solution of calcium chloride or stronger solutions of sodium or potassium chloride. In conventional rotary drilling operations the wall of the hole is exposed to drilling mud for days, weeks, and in some instances for as long as several months. During this time, drilling mud filtrate seeps slowly into formations surrounding the hole. The permeability and stability of many formations, especially those containing clayey materials, are impaired by the mud filtrate. Often interaction between the mud filtrate and the formation causes drilling and production difficulties. Serious reduction in productivity of oil and gas formations during drilling, completing and repairing wells has been noted often in recent years. Cases are known of development wells which produced only small volumes of fluid upon completion. However, after a period had elapsed, they began to produce oil or gas in commercial quantities. In other cases, results of drill-stem tests taken during the drilling of deep wells have indicated good production should be obtained from shallow formations. Later difficulty has been experienced in obtaining production from these shallow formations which had remained in contact with drilling muds for an extended time. In yet other cases wells have failed to attain the productivities expected from previous performance after the use of drilling mud as a circulating fluid during workover operations. It is evident from the field behavior cited that the productivities of certain oil- and gas-bearing formations have been damaged by exposure to drilling muds. This reduction in well productivity, called "formation damage", causes serious consequences. In development wells, expensive remedial operations are incurred. In wildcat wells, good formations may appear to be marginal or even non-productive. The importance of formation damage has been recognized by a number of investigators1-s who have considered the effects of fresh water, saline solutions and aqueous mud filtrates on the permeabilities of formations. A general conclusion from such studies is that interaction between water and formation clays reduces permeability of reservoir rock and that the permeability decreases as salinity of the water decreases. Data in these references, however, concern the permeability change with only a single fluid present. A more pertinent and direct consideration in the production of oil and gas from wells is the permeability change when two fluids, oil and water, are present. Recognizing this, Nowak and Kreuger2 and Bertness1" considered several ways in which mud filtrates and saline solutions caused reductions in the oil permeability of formation cores. Investigations discussed here were designed to supplement information in the literature on changes in oil

By Donald A. Corrigan, John Chipman

It is shown that the heat of solution of nitrogen in liquid-iron alloys is Proportional to the interaction coefficient. This proportionality forms the basis for a method of predicting nilrogen solubility at any temperature when the interaction coefficient is knoun at 1600°C ov when the solubility is known at some one temperature. A method for predicting the solubility of nitrogen in liquid steels, including alloy steels, was proposed some years ago by Langenberg.&apos; Since the data available at that time were restricted to temperatures of about 1600°C, his predictions were similarly restricted. More recently, Nelssonz devised an approximate method for estimating nitrogen solubilities at higher temperatures. It is the purpose of the present paper to present a method by which the solubility of nitrogen at any temperature within the steelmaking range may be predicted from the known interaction coefficients at 1600°C. Nitrogen in iron and in all of the alloys to be considered here is known to obey Sieverts&apos; Law; hence the activity of nitrogen in an alloy of fixed composition is proportional to its concentration, here expressed in weight percent. The activity of nitrogen is defined as equal to its weight percent in the binary Fe-N solution at any temperature. Its activity coefficient in any alloy is the comparison being made at equal values of T and PN2. In all alloys the activity coefficient changes with composition, log fN being a linear function of the percent of alloying element at low concentrations. In the following calculations the alloy compositions are restricted to those in which this linear relation is exhibited. For most systems this is a fairly wide range, for example up to 5 pct V and to 10 pct Cr or Ni. For this composition range. complex alloy is the same as that in the Fe-N-j ternary solution. Langenberg&apos;s method of prediction was based on Eq. [3], the values of log fN for various additions being taken from a graph. Instead of using the simple addition indicated in Eq. [3], he used a more complex method suggested for Fe-S-j alloys by Morris and Buehl.3 For the composition ranges in which Eq. [2] is valid the two methods are equivalent. Nelson extended the prediction to other temperatures on the assumption that logfN is inversely proportional to absolute temperature. It may be shown that inverse proportionality would result if the partial molal entropy of nitrogen were unaffected by addition of the alloy element, an assumption which Nelson designated as a "regular" solution. It has been shown recently by the authors4 that this assumption is not a good approximation. The heat of solution of nitrogen (N2) in an alloy may be obtained if the solubility is known as a function of temperature. Measurements of this nature have been reported recently by Beer5 for Fe-Mn alloys, by Nelsson2 for Fe-C, by El Tayeb and parlee6 for Fe-V, and by Pehlke and Elliott7 for many alloys embracing a wide range of compositions. In connection with the work of the last named authors it is noted that their Fig. 22 gives the heat effect per half mole rather than per mole of N2. In using their data we have shifted some of their values slightly by using the best straight line in preference to their curve. Their data, supplemented by others from the literature, are summarized in Table I. In Fig. 1 the heat of solution of nitrogen is shown as a function of composition for the several alloy systems. The difference between the heat effect in the alloy. AH; and that in pure

Jan 1, 1965