Search Documents

By Richard J. Mainiero

INTRODUCTION Because of the hazards associated with flammable methane gas and coal dust, the shooting of mudcaps (adobes) or other unconfined explosive charges in underground bituminous coal mines is prohibited; all explosives must be fired in stemmed boreholes. However, there are situations where it would be advantageous from a safety standpoint to fire open shots. This would be in the areas of dislodging loose roof slabs, overhangs, rock-fall leveling, slab or boulder breaking, crib removal, and crevice shooting. The Bureau of Mines, U.S. Department of the Interior, has been developing an explosive charge that is non-incendive; that is, detonation of the charge will not ignite a flammable atmosphere. This explosive charge could be applied to the blasting conditions mentioned above. As of this writing, the explosive charge has not yet been certified as "permissible" for use in flammable atmospheres, but the necessary protocol is being finalized with the Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The explosive charge described in this paper is merely a prototype sheathed rock-breaker charge (sheathed permissible explosive rock- breaker charge) demonstrating the feasibility of such a device. Industry may modify the design and composition of the charge in producing a commercial product so long as it is still safe, as defined by a testing schedule being developed by the Bureau of Mines and MSHA.

Jan 1, 1984

By C. C. Miller, A. B. Dyes

The cost of finding and developing new reserves is continually rising. We must meet these rising costs with more economical operations. This can he accomplished if we revise our ideas of proper well spacing and well allowable to consider the concept of optimum well spacing. According to this concept, the optimum spacing is the one which leads to the maximum present worth for a reservoir when ail factors affecting total cost and total revenue are considered and when the wells are produced in the most eficient manner. Application of this principle efficiently utilizes available well potential and properly considers the recovery eficiency in addition to fixing the spacing on the basis of the amount and value of the oil to he recovered. This Study presents an analysis of one producing zone containing low gravity crude to illustrate the effect of these factors on the present worth and on the optimum economic spacing under two production drives—-evolved gas and water drive. The maximum present worth occurs when the optimum number of wells for open-flow operation is employed. Frequently, this optimum development cal1s for very wide spacing and the ideal field rates are not unreasonable. Under other circumstance. where proration is necessary, an optimum combination of well spacing and well allowable exists which permits production at relatively high rates. The optimum well density in a field depends on the recovery efficiency and the valule of the oil. In solution gas-driven reservoirs this optimum spacing for operation at high producing rates can vary from extremely wide spacing to handle viscous low gravity oil in thin formations to relatively close spacing in thick sands where good recoveries are expected. Because of the better recovery from water-driven fields, the optimum spacing in these fields is closer than in solution gas-driven fields. Also, the water encroachment pattern is dependent upon the well spacing, and an adequate numher of wells is needed to assure a good sweep eficiency. The economic optimum well density in a water-driven field is high enough for this purpose. INTRODUCTION From year to year domestic oil becomes more difficult to find. The fields we do locate are frequently smaller and deeper than older fields and the costs for men, material and equipment are continually rising. To replenish our reserves we must continue to search for and develop new fields, but experience has shown we cannot expect prices to rise in proportion to costs. Consequently, we must meet increasing costs by more economical operations. A vigorous effort is being made within the industry to improve exploration methods, to cope with the problems of deeper drilling, and to obtain a secondary yield from older fields. Many significant contributions have resulted from these efforts. The economic operation of new fields can be further improved by developing these fields on optimum spacing and producing the wells at higher rates. This would avoid the drilling of unnecessary wells and provide additional capital for seeking new oil. While the benefits of these practices are obvious, the problem of defining the optimum development of a field for natural depletion can become very complex. A study of the effect of well spacing and several reservoir variables on economic worth of a specific field is reported here to illustrate the problem and to show the magnitude of the benefits to be realized. This study is necessarily limited to the field conditions selected and is not intended as a general solution of the well spacing problem. It does, however, indicate factors to be considered, the trends to be expected, and the direction in which we should proceed in developing new fields. NO consideration is given to land and legal considerations which might arise. METHOD OF ANALYSIS The optimum method of developing and producing a field is to use the combination of spacing and prora-tion which gives the maximum return. In addition, we do not want to lose recovery. These considerations of maximum return and maximum recovery present no serious conflict. The value of each method of operation is conveniently expressed in terms of its present worth. According to the present worth method of evaluation,' an acceptable annual percentage return is assigned to the operation, and all incomes, capital costs, and expenses are discounted at this rate to the start of the operation. This net value is the present worth. If we apply the same discount rate to several alternate methods of operation, the one yielding the greatest present worth is the best method. If we express net income in terms of price per barrel of oil produced, drilling and equipment costs on a well basis, and expenses as cost per well year, this evalu-

By A. E. Blakeslee

Morphological and electrical properties of GaAs epitaxial layers are influenced not only by changes in the nominal substrate orientation but also by small amounts of misorientation from the exact crystal planes. Deviations up to 5 deg from {11IA}, {11IB}, and (100) planes were investigated. Growth rates increase progressively with angle, approximately I u per hr per deg. Size and density of growth pyramids fall off with increasing angle, but other effects that are deleterious to the surface may occur which are heightened by increased misorientation. Carrier concentration decreases and electron mobility consequently increases as the angular offset increases, except in the case of strong compensation, where the mobility trend is reversed. It has long been known that changes in the crystallo-graphic orientation of the substrate may cause pronounced effects on the morphological properties of vapor grown semiconductor films. Reports of orienta-tion-dependent growth rates and surface characteristics are as old as the literature on epitaxy itself. shawl has recently published a comprehensive study of the dependence of growth rate on substrate temperature and orientation in epitaxial GaAs. It is also well-known that misorienting the substrate surface a few degrees away from the nominal low-index crystal-lographic plane often produces a much smoother epitaxial surface. This was reported by Tung2 for silicon, Reisman and Berkenblit3 for germanium, and by Kontrimas and Blakeslee4 for GaAs, and use is commonly made of this fact in the semiconductor industry to help guarantee smooth vapor deposits. The effects of substrate orientation on the carrier concentration and mobility of vapor grown GaAs were first documented by williams5 in 1964 and have been observed by several other authors since then,6,7 but no one has yet reported a careful study of how small changes influence these properties. We have made such a study and have found that sizable differences in growth rate, morphology, carrier concentration, and mobility can indeed be observed for epitaxial films grown on substrates that are oriented by progressive small increments away from the exact crystal plane. EXPERIMENTAL Early in the investigation an arsine synthesis system of conventional design8 was employed to produce growths on {111A}-oriented GaAs substrate crystals. In that early work, pronounced effects on carrier concentration and electron mobility were observed as a function of slight misorientation from this low index plane. That observation led to the more careful study that is reported here. An AsC13 system, differing in major aspect from those commonly in use today9 only in that the reactor is vertical rather than horizontal, was used for the detailed study. The gallium source was at 900°C and the substrates were at 750°C. The flow rate of pal-ladium-diffused H2 through the AsCl3 bubbler was 200 cu cm per min, and the flow rate of bypass H2 was also 200 cu cm per min. The substrates consisted of chro-mium-doped semiinsulating GaAs to facilitate elec-trical evaluation of the overgrowth by means of Hall and conductivity measurements on conventional eight-legged Hall bridges. They were misoriented by 0 to 5 deg from the {111A}, {111B}, and (100) planes, toward the (100) from the {111A} and {111B} and randomly toward the <111A> or <111B> from the {loo). The crystals were oriented for sawing by the Laue back-re-flection technique, which is good only to about ±1/2 deg; but after polishing or sometimes after epitaxial growth the wafers were checked by a diffractometer technique which is accurate to about * 0.1 deg. After lapping, the wafers were polished with NaOCl after the technique of Reisman and Rohr,10 and just before use they were cleaned in NaOC1, thoroughly rinsed with de-ionized water, and blown dry with nitrogen. Each run employed four wafers, each misoriented by differing amounts from one of the three major faces, and at least two runs were made for each orientation. The runs were continued long enough to provide at least a 15-µ or thicker layer. SURFACE MORPHOLOGY The appearance of all the films that were grown in a given run always changed from wafer to wafer as a function of increasing misorientation, but not always in the same regular fashion. At least three different trends were observed. These are more easily seen than described, and reference to the series of photo-

Jan 1, 1970

By Ma Guang, Huang Jinshou

In this paper we briefly describe measuring techniques and their practical use in the mining industry of China. A strain coefficient matrix of triaxial strain cell for a flat ended borehole is also introduced.

Jan 1, 1983

By S. Ramachandran, R. A. Walsh

Many investigations have shown that the manganese enhances the deoxidation power of silicon. Here it is suggested that this phenomenon could be explained in terms of the formation of impure silica. Data of Hilty and Crafts on the Fe-Mn-Si-O System has been evaluated on the basis of the reaction S_i + 20 = (SiO2) where (SiO2) denotes silica of variable activity. The activity of silica in this system is a function of aMn/aSi and the temperature, and can be described by the equation 12700 l°gaSiOz = -6.85+ - - 0.5 log aMn /asi PRACTICAL melting experience has shown that it is helpful to maintain a certain range of Mn/Si ratio in deoxidizing quality alloy steels. Herty,1 as early as 1932, reported a strong association between manganese and silicon as did schenck2 and Korber and Oelsen3 in later work. More recently, Hilty and crafts4 have studied the solubility of oxygen in the Fe-Si-O system, both with and without manganese. Their study confirmed the marked ability of manganese to increase the deoxidizing power of silicon. This phenomenon has remained unexplained in the liter,ature5 since it has been shown that manganese has virtually no influence on the activity coefficients of silicon or oxygen.= In this paper, an explanation for the role of manganese is suggested and equations are devised for quantitatively describing this influence. DISCUSSION Hilty and crafts4 equilibrated their melts under an argon atmosphere and the system established equilibrium with a self-generated slag which was not always the oxide of lowest free energy. Drawing on the early work of Korber and Oelsen,3 it was reasoned that the formation of complex Fe-Mn-silicates

Jan 1, 1963

By G. D. Tranter

The importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By G. D. Tranter

The importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By Evan Just

Engineering education for the mining industry has been undergoing a gradual change in recent years, to an extent that many employers may not realize. The result of this change is that the new graduate comes to his first employment with very little knowledge that is immediately valuable in operations. He is in fact, simply "half-baked" and needs much education on the job before his schooling will pay out in any significant way. To the employer who fails to recognize this, and fails to give the necessary training to finish the educational job, the modern graduate is likely to be unsatisfying. Moreover, the young fellow&apos;s future competence will be impaired. However, to the employer who assumes the educational burden, the effort should pay out as the half-baked products, after a few years, ought to be more useful than their predecessors and should have a greater potential to solve problems or cope with change. The reasons for this development are given below in the foreword to a questionnaire survey circulated by the SME Committee for On-the-Job Training.

Jan 6, 1964

By James B. Vance, Parviz Mottahed

An extensive research program has been carried out at PCS Mining for some time into the use of high frequency microseismic emissions in the range of 30-200 kHz for roof fall warning in the mines. A laboratory investigation on loaded samples of potash has established a close correlation between acoustic emissions and the applied load. The tests also indicated the occurrence of the Kaiser effect. The positive and encouraging response from underground testing and controlled laboratory testing has lead to the extension of the investigation into correlation of the high frequency microseismic emissions and the change in stress distribution due to mining. Hydraulic borehole pressure cells were installed at different depths ahead of the advancing boring machine. The output due to the stress change and the microseismic event count was monitored by a continuous chart recorder. This paper discusses the results of this instrumentation. The results confirm the strong correlation between the two measured parameters and outlines future areas of research for the use of the high frequency microseismic emission techniques in quantifying the changes in stress distribution.

Jan 1, 1984

By G. R. Love, M. L. Picklesimer

Aboue 950°C the Nb-Zr system consists of a completely miscible bcc solid solution, commonly called the phase. Between 950 and 600°C, and between 20 and 85 pct Nb, the phase deconlposes, after sunciently long times, into two bcc solid solutions. The pct Zr alloys are conveniently descibecl with T-T-T (time-temperature-transformation) curves having a nose at about 2 hr at 700°C. The reaction rate varies only slowly with zirconium content and negligibly with oxygen contanzination; it is speeded up by a factor of 10 to 15 by 90 pct cold ulork and slowed dou by n factor oj 10 to 30 by a two-hundrecljold increase in grain size. Nb-r alloys with compositions between 40 and 85 pct Nb have been the basis for the majority of commercially important superconducting materials. In part because of their commercial promise, more is known about these alloys than about most other high-field superconducting materials. At the same time, there is considerable disputed or incomplete metallurgical information. For example, although Rogers and tkins&apos; indicate a monotectoid reaction at approximately 600°C and a two-phase 01 + 0, field extending between 20 and 85 pct Nb and to a maximum of 95OGC, erhout&apos; has reported that this entire region would be a single homogeneous B were it not for oxygen contamination. Again, although it has been shown that relatively short-time heat treatments in the vicinity of 700CZ significantly improve the ability of short wire samples to carry high currents in high magnetic fields at 4.2K, these observations have never been fully correlated with the structural change or changes occurring during the anneal. We intend to investigate in detail the effect of metallurgical variables, including heat treatment, on the superconducting properties of hard superconductors. To verify that our experimental techniques are valid and to establish a relative standard against which other materials may be measured, we feel it advisable to know the behavior of the Nb-Zr alloys under a variety of processing conditions. As an initial step toward this goal, we have determined in detail the kinetics of the transformations in Nb-Zr alloys. EXPERIMENT A number of problems had to be solved before beginning any fruitful work on the reaction kinetics in this system. While solving some of these problems, either by chance or by design, small amounts of information were obtained about alloys containing 40, 50, 60, 65, 67, 70, and 75 pct Nb, bal. Zr. In addition, a large range of grain sizes and a range of temperatures considerably greater than the range indicated by Rogers and Atkins phase diagram were examined. We will, however, report in detail only the results obtained for the Nb + 33 pct Zr and Nb + 25 pct Zr alloys at three grain sizes, two levels of oxygen contamination, and the temperature range 550 to 950°C. These data are most complete, but the other data are sufficiently complete to indicate the kind and magnitude of the variation of the transformation kinetics outside this range. The first and most difficult problem encountered in this inquiry was one of sample homogeneity. When Nb-Zr alloys are arc- or electron-beam-melted on a cooled copper hearth, solidification is sufficiently slow that there is appreciable coring in the cast structure and a large variation of grain size across the button thickness. Both these factors significantly affect the apparent reaction rate in the system. A two-step solution to the problem was attempted; an arc-melting and drop-casting technique has been developed by conald that greatly reduces the as-cast grain size and virtually eliminates coring segregation. Ingots made in this way exhibited no detectable (3 pct maximum) zirconium segregation. Before it was evident just how good this technique was, we attempted to supplement it with rather long-time, high-temperature annealing of the cast ingots. This annealing was carried out in evacuated and sealed (seal-off pressures < 1.0 x 106 torr) quartz capsules lined with tantalum foil at 1400 to 1450 C for 8 to 72 hr. There were two principal effects of this treatment: the grain size increased to a fairly uniform 150 p, and the surface and all grain boundaries near the surface acquired a film of a second phase, tentatively identified as an oxide (possibly additionally contaminated with silicon). There was no evidence that this 1400 C treatment had affected the zirconium segregation. High-temperature annealing was subsequently used only for grain-size control, but anneals of longer than 4 hr at temperatures greater than 1000°C were performed in dynamic vacuums (pressure no greater than 1.0 x lo torr). Any contamination resulting from these treatments was well below the limits of detection of our techniques. All samples, as cast, were cold-swaged to at least 85 pct reduction in area. The samples called cold-worked were tested as swaged. The minimum re-crystallization anneal for these alloys was about 12 hr at 1050 C; this produced an equiaxed grain diameter of about 4 to 8 P. Annealing for 4 hr at 1450°C produced a grain size of about 80 to 150 p; and annealing for 4 hr at 1650aC, close to the melting point of many of these alloys, produced a grain size of 0.5 to 1.0 mm. At all temperatures, the larger grain size was

Jan 1, 1967

By Don L. Kendall, Martin G. Buehler

A simple physical model has been developed to fit carrier-removal data in silicon irradiated near room temperature with reactor spectrum neutrons. Commonly observed donor and acceptor defect energy levels are assumed to be introduced linearly with neutron fluence. The donor levels (in ev) are Ev + 0.16, Ev + 0.27, and Ev + 0.31 and the acceptor levels are Ec - 0.55, Ec - 0.40, and Ec - 0.1 7, where Ev and Ec are the valence and conduction band energies, respectively. The introduction rates of each level are adjusted to fit literature initial carrier-removal rate data. When normalized with respect to the Ev +0.27 level, the relative values of introduction rates are 5.3, 1.0, 3.1, 1.0, 2.0, and 20.0, respectively for the six levels indicated above. To fit p-f (hole concentration vs neutron fluence) and n-f (electron concentration us neutron fluence) data, the introduction rates are multiplied by a factor which preserves the relative values given above. This factor depends upon irradiation temperature, reactor energy spectrum, neutron fluence calibration, and oxygen content of silicon. An extensive study of the effect of neutrons on carrier-removal in silicon irradiated with reactor spectrum neutrons (E > 10 kev) has been given by Stein and Gereth1 (SG) and Curtis, Bass, and Germano&apos; (CBG). They measured initial carrier-removal rates for both p- and n-type silicon over an impurity range typical of silicon devices. In this work, we attempt to fit a simple theory to this data to establish a usable relationship between hole and electron concentration, p and n, respectively, and neutron fluence f. The p-f and n-f relations are needed to assist in the design of neutron tolerant silicon devices and are needed to clarify presently used empirical resistivity-fluence relationships.3 Neutron damage in silicon produces a variety of defects ranging from simple point defects to defect clusters. For the purpose of this treatment, we assume that simple point defects dominate carrier-removal effects. In contrast to this view, stein4 has proposed that defect clusters are responsible for a significant portion of carrier-removal effects. In the following section, it is shown that the carrier-removal effect in n-type silicon with an electron concentration less than 1015 cm-3 can be explained adequately by assuming that the divacancy is the dominant defect and that its introduction rate is independent of the electron concentration. For electron concentrations greater than 1015 cm-= an additional acceptor defect center is needed, and for simplicity the A-center (vacancy-oxygen pair) has been chosen. Although the E-center (vacancy-phosphorus pair) can account for some of the results, the A-center was chosen because the E-center requires a more involved treatment which the presently available data do not justify. In p-type silicon three radiation-induced donor levels are assumed, namely the divacancy and two other centers of unspecified nature located at Ev + 0.16 ev and Ev to 0.31 ev. The donor divacancy at Ev + 0.27 ev is assumed to be introduced at the same rate in p-type as in n-type. However, this rate is too low to fit p-type initial carrier-removal data. The dominant centers in p-type silicon are assumed to be the Ev + 0.16 ev and Ev + 0.31 ev levels where the latter is not the divacancy. The introduction rates are chosen to fit initial carrier-removal rate data. Assuming that the introduction rates are independent of Fermi level, the ratio between them is fixed for subsequent p-f and n-f calculations. Using the same ratios, the initial carrier-removal rate data1,2 as well as p-f and n-f data1,5 can be fit provided the absolute value of the introduction rates are adjusted to account for irradiation temperature, reactor energy spectrum, neutron fluence calculation, and the oxygen content of silicon. THEORETICAL ANALYSIS This analysis is basically the same as that used by Hi116 to analyze electron damage in silicon except we express the degree to which an impurity level is ionized not in terms of the Fermi level, but in terms of carrier concentration. Landis and pearson7 have used the latter approach to analyze y-damage in silicon. Neutron-induced defects responsible for carrier-removal at room temperature are assumed to be simple point defects with no interaction between defects so that they may be represented by discrete energy levels. It is also assumed that no constituent of a defect complex is used up and defects stabilize shortly after irradiation. Defects are assumed to be introduced linearly with fluence according to the product Rtf where Rt is the defect introduction rate and f the neutron fluence. Taking into account the ionization of defects according to Fermi statistics, and considering charge neutrality where minority carriers are neglected, the n-f relation is where no is the preirradiation electron concentration. The parameter Nt is the electron concentration at which the ionized defect concentration is one-half the total defect concentration (Rtf) or where Et is the defect energy level. For silicon at 300°K, ni = 1.45 X 1010 cm-3 and Ei = Ev+ 0.542 ev which was determined using Ec — Ev = 1.11 ev and me* = 1.07 mo and mh* = 0.558m0. The spin degeneracy factor, which usually appears as a number multiplying the Nt/n term of Eq. [1], is taken as unity. In effect, this factor has been incorporated into the defect en-

Jan 1, 1970

By J. W. Goss, M. J. Coolbaugh

A survey of literature published in the U.S. on grouting indicates that most such work has been done to stop water flow in mines and for stabilizing foundations of various man-made structures. Apparently San Manuel is one of the first mines in this country to use grout extensively underground for the strengthening and stabilizing of ground about drifts, shafts, and stations.

Jan 3, 1961

By R. P. King

Flotation plant simulation, a relatively recent methodology in mineral processing, is defined and corresponding uses are discussed. Typical simulation structures are compared. Current problem areas exist although these are not insurmountable. Following a brief state of the art discussion, the N. I. M. simulation program is reviewed. In general, digital plant simulation is expected to be of substantial benefit in the near future.

Jan 1, 1976

By Richard Moldenke

One of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent;, and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing 90 per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 per cent. of the charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used. The recent advance in knowledge of rational melting and the consequent reduction in losses directly due to oxidation of the metal and cold iron, has permitted the acceptance of castings with a much higher sulfur content than formerly. The steel industry also is seeking to determine how high sulfur may go with safety. In the iron foundry, however, there is the danger of a low cupola bed or an unduly retarded air-furnace heat, with the consequent raising of the freezing point of the metal and segregation effects resulting from high sulfur with insufficient manganese. The iron foundryman must, therefore, have a means of correcting his

Jan 1, 1922

By Edward Steidle

It has been said that "the command of nature has been put into the hands of man before he knows how to command himself," and what we see about us gives particular emphasis to this observation. If this condition be granted, the vaunted boast of school and college, of the institution that had the training of this generation, and of its fathers, and of its grandfathers, the boast that education is a "preparation for life," stands exposed as a hollow claim, or as a ghastly, cynical conception of life, or else education has fallen far short of its intentions. It has been evident for some time that education was not meeting the fullest expectations of society. In recent years there has been a deal of speculation indulged in by both laity and faculty in regard to American education and American civilization, and some few and sporadic changes have been effected. Today, however, there is no longer time for mere hypothetical considerations; we are faced with certain definite facts and confronted with obvious conditions that will not wait for fine-spun theories. If educators do not put their house in order, someone else will do it for them. The trends in mineral industries education must be in harmony with this general realignment that is today visible on the educational horizon, and only as these trends are in conformity with this movement can they be called sound. Two questions, then, confront mineral industries educators: (1) What are the trends in mineral industries education, and (2) how do these trends correlate with the major educational movements of the day? Scope or Mineral Industries Education Before launching into these particulars, it might be well to define the scope of mineral industries education and to consider its present position. Mineral industries education embraces three main types of work: 1. Earth Sciences and Geography.—Geology, mineralogy, geography— courses basic to all mineral industries and to the humanities. 2. Mineral Engineering.—Mining, petroleum and natural gas—dealing with mineral producing industries. Application of earth sciences and all types of engineering to exploitation of natural mineral resources.

Jan 1, 1934

By Richard Moldenke

One of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent;, and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing 90 per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 per cent. of the charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used. The recent advance in knowledge of rational melting and the consequent reduction in losses directly due to oxidation of the metal and cold iron, has permitted the acceptance of castings with a much higher sulfur content than formerly. The steel industry also is seeking to determine how high sulfur may go with safety. In the iron foundry, however, there is the danger of a low cupola bed or an unduly retarded air-furnace heat, with the consequent raising of the freezing point of the metal and segregation effects resulting from high sulfur with insufficient manganese. The iron foundryman must, therefore, have a means of correcting his

Jan 1, 1922

By C. V. Millikan

When a flowing oil well is being drilled in with cable tools, it is difficult to determine when an additional streak of pay sand is drilled. By placing a gas meter on the gas-release line from the oil and gas separator, any increase in volume of gas that comes with oil production is recorded. In addition to the better knowledge of sand conditions, these data are a valuable aid in determining the size and depth of shots, plugging off water, and estimating ultimate production. The meter also gives a record of operation while the well is drilling in; and if allowed to remain on the well after completion will give information that may lead to a more efficient recovery of the oil from the sand. A VERTICAL cross section of any oil sand will show great variation in porosity and oil content. In some sands, the entire thickness contains oil, the variation being only the degree of porosity or oil content, but more often the pay streaks are distinctly separated by shells or barren streaks. These pay strata vary in number and may be thin or thick. The total thickness of the sand may be several tens of feet while the part containing oil may be only 1 or 2 ft. thick. The amount of production is not proportional to the thickness of the sand but rather the thickness of the pay streaks. If the total thickness of the sand or the amount that can be drilled is small, or if the initial production is small, the depth at which each stratum of pay is encountered can be determined sufficiently accurately for all present economic purposes. However, when drilling through sand of considerable thickness, giving large initial production, especially where conditions necessitate that the production go through the same gas trap with that from one or more wells already producing, it is difficult to determine the depth at which the pay strata are encountered even accurately enough to guide the placing of shots, and small pay streaks are apt not to be recognized at all.

Jan 9, 1925

By L. F. Engle, M. A. Hewedi

SUMMARY Initial interest in using solutions of ammonium salts to leach native copper was documented in notes from an AIME meeting in 1871; By 1916-1917, application of the NH3-CO2-H2O system to recover nonferrous metals attained commercial significance, when it was used as a process for copper recovery by Kennecott Copper Corporation and Calumet & Hecla Mining Company. The Caron work in the early 1920s, Freeport Sulphur Company’s achievements leaching Cuban laterites during World War II, out- standing accomplishments in both eastern and western Canada, recovery of manganese related to the work of Dean -- all serve as landmarks as this One Century Review surveys a base for future technology. Current emphasis on compatibility of metals-producing systems with the need to meet environmental protection criteria provides special encouragement to researchers and engineers to find accept- able ways of recovering metals. The ever-present demand of management to design, build and operate facilities on a profitable basis provides additional impetus to apply information from the technical literature to that need. Examination of the general approach to this paper will reveal much that is firm and positive with respect to empirical results -- extractions, recoveries, amenability to familiar proven equipment and materials of construction common to the industry. Although there are many references, there are gaps in the basic scientific data that if filled could lead to even more usefulness; the paper attempts to indicate where further information is needed.

Jan 1, 1973

By A. U. Seybolt

RECENTLY, cases of coexisting ordered and disordered phase equilibria have been reported among face-centered cubic metals,1"3 but not on body-centered cubic systems.4 McQueen and Kuczynski5 showed a single line as the boundary between ordered solid solution of Fe3Al type and corresponding disordered solution in the Fe-A1 phase diagram based mainly on dilatometric and magnetic measurements. Such a single line would indicate a second or higher order transition. or an absence of coexisting order and disorder. The writer found previously a two-phase equilibrium region at 800°C consisting of ordered and disordered solid solutions of Fe3Si in a matrix of approximately 1-6 wt pct Si (Fe3Si is of 14.3 wt pct Si). A similar two-phase region of ordered and disordered Fe3Al solid solutions might be expected if the similarity between Fe3Si and Fe3Si structures hold true. In the present investigation, a wire of 22 at. pct Al, balance Fe and 0.0513 cm in diameter was subjected to electrical resistivity measurement in vacuum as a function of temperature between 300 and 800°C, see Fig. 1. There was excellent agreement between data taken on heating and on cooling: no hysteresis was observed. The Curie temperature was determined to be 640 °C which agrees with the finding by McQueen and Kuczynski.5 But in addition, there were two transitional points in the resistance-temperature plot at 510oC and 400 "C. The former is thought to be a connection with the transition from disordered state to a coexisting order and disordered equilibrium state; while the latter, from such coexisting state to ordered state. Fig. 2 shows a phase diagram where the suggested two-phase region lies between dotted lines. The solid lines are those of McQueen and Kuczynski.5 Since these authors found only a single-phase boundary between ordered and disordered Fe3 Al, it would seem likely that the dilatometric method used by these authors was not sufficiently sensitive to resolve the ordering reaction into the two-phase boundaries. In addition, their phase diagram conflicts with the statement they make on P. 1 of their paper: "The sharpness of the peaks indicates that ordering to Fe3A1 is a first order reaction." The suggestion of coexisting order plus disorder in Fe3A1 must be considered tentative until confirmed by high-temperature X-ray examination. If

Jan 1, 1961

By Fred E. Beasley

Metallurgists have, in the last ten years, overcome many difficulties of high zinc in lead blast-furnace slags. This problem was brought to the front at the close of the war, by the price obtained for lead and the high cost of labor, fuel, and flux. The Port Pirie plant of the Broken Hill Associated Smelters, Australia, early in 1919 had increased the zinc oxide in its blast-furnace slags from 13.5 to 20 per cent., at the same time reducing the iron oxide in the slag from 33.5 to 25.6 per cent. These results were obtained by the addition of 10 to 12 per cent. granulated slag to the roaster charge, improved conditions of the crushing, mixing, and roasting of the constituents of the sinter. By experiments and improvements, the practice at this plant has developed a normal slag that carries 22 per cent. zinc oxide, and at times runs as high as 33 per cent. zinc oxide, with only slight furnace trouble. The granulated slag is used not only as a diluent to the sulfur in the roaster charge, but on account of its value as a slag-forming material and the physical properties it imparts to the finished sinter. The ore is mixed with flux and given a double roast. All the first roasting is by sintering with the Dwight & Lloyd machines. The final roasting is performed partly by Dwight & Lloyd machines and partly by H. & H. pots. The charge to the blast furnace consists chiefly of the final sinter, slag shells, siliceous and non-bearing sulfur lead ores. High blast and ore columns are the practice. The greatest care is taken to obtain in the final sinter as low a sulfur content as possible. Attracted by the success of the Port Pirie plant, The Consolidated Mining & Smelting Co. of Canada, at Trail, B. C., in 1920 treated its crushed primary sinter with about 15 per cent. granulated slag. The Trail smelter at this time was short of ore and a large part of the charge to the roasters consisted of the zinc-plant residue having the following analysis: 12 to 16 per cent. lead, 12 to 16 per cent. zinc, and 25 to 30 per cent. iron. The lead in the final sinter was low and the physical condition was so bad that all the sinter had to be screened before it could be charged to the blast furnace. Also it disintegrated on being trammed and dumped

Jan 1, 1925