Search Documents

By Philip R. Whitney

Deposition of manganese oxides is of common occurrence in streams of the north-eastern United States. Manganese entering the stream in solution in ground water is oxidized and deposited in the stream, primarily as oxide coatings on detrital materials. Prevalence and thickness of the coatings increases with increasing particle size in the coarse sand and gravel range. A number of metals of economic and environmental interest are enriched in these coatings. Samples of 8 to 16 mm pebbles were obtained from two streams in the Shawangunk region of southeastern New York State, an area of know71 Pb/Zn/Cu mineralization. The pebbles were leached to remove the oxide coatings and the resulting solutions analyzed for Mn, Fe, Pb, Zn, Cd, Cu, Co, and Ni. Trace-metal/Mn ratios in these streams are generally one to two orders of magnitude higher than regional background values. Profiles of trace- metal/Mn ratios along the streams show considerable detail; contributions of metals from tributaries are sharply reflected in the metal content of the oxides. The potential advantages and disadvantages of using coated stream gravel for geochemical prospecting and environmental studies are discussed in the light of these and other data.

Jan 1, 1976

By C. Laird, C. E. Feltner

An investigation into the effect of a material's slip character on its high strain fatigue properties has been carried out using copper and Cu-7.5 wt pct A1 as representative wavy and planar slip mode materials, respectively. In copper, the constant term and exponent in the Coffin-Manson equation, ?EpNf1/2 = const, are unaffected by the temperature of testing or the history of the metal. On the other hand, in Cu-7.5 wl pcl Al, while the exponent is invariant, the constant is increased with respect to copper and increased further with decrease in temperature. The life in Cu-7.5 wt pct A1 is double that of copper at room temperature and about four times at 78°K. Fractoflaphic studies indicate that these diffevences in life are associated with the early stages of cracking. In copper, severe surface rumpling provides crack nuclei at pain boundaries independent of' testing temperature or the history of the metal. In Cu-7.5 wt pct Al, the planar slip mode of deformation prevents grain boundary folding; crack nucleation is therefore mainly transgranular and the increase in life with respect to copper is associated with a prolonged linking-up stage of such transgranulay cracks. At the lower temperature the increased difficulty of cross slip inhibits multiplication of trans-granular cracks and retards the linking-up process, giving a further enhaancement in life. It is expected that such behavior will be found general in materials of wavy and planar slip mode, respectively. STAGE II crack propagation in high strain fatigue takes place by a repetitive process of crack tip blunting in the tension part of a fatigue cycle followed by resharpening of the crack in the compression part.1-3 This mechanism has come to be called the "plastic relaxation process".3 At very high strains (lives to failure less than 103 cycles), most of the life of a specimen is spent in crack propagation by the plastic relaxation process.4,5 Since the differences in the cyclic strain hardening behavior of metals and alloys are comparatively small in this strain range,6,7 the amount of blunting at a crack tip depends primarily on the applied strain amplitude. The rate of crack propagation in this life range is therefore nearly constant with respect to material and temperature of testing. In the longer life portion of the high strain fatigue range (l03 to 103 cycles to failure), a considerable fraction of the lives is spent in crack initiation and Stage I growth. Grain boundaries have frequently4,5,8 been found to be the sites for this growth which is also associated with a surface folding process.4'5 Such folding behavior may also be general in any material having a grain structure and capable of plastic deformation. It has therefore been suggested475 that the universality of the Coff in-Manson law,9'10 constant,* where ?Ep is the plastic strain range and Nf the number of cycles to failure, is reflected in the approximate invariance of both the crack initiation and propagation behavior. It happens that, in most investigations of the phenomena associated with failure,4,5,8 materials with a wavy slip mode have been used as vehicles for the studies, or else "normally" planar slip mode materials have been tested under conditions giving rise to wavy glide deformation, e.g., stainless steels cycled at high temperature.'' The purpose of the present investigation was to determine whether or not different cracking phenomena would occur when the slip mode of a material is planar and if the associated life to failure would be different than that of a wavy slip

Jan 1, 1968

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many localities.1-3 As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermo-electric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the. pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1-the validity of the calibration of the pyrite geothermometer; and 2-the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating, pyrite geothermometer temperatures and thermo-electric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.' Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermo-electric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1952

By C. B. Alcock, R. G. Hudson

Sulfur pressure measurements above FeS in equilibrium with iron have been carried out by the Knudsen orifice method. A comparison is made of the weight loss of the cell per unit time obtained in the above experiments, that calculated from Richardson and Alcock's measurements of the S2 pressure above FeS in equilibrium with iron, and the dissociation constant for diatomic sulfur from spectroscopic and thermal data. EXTENSIVE equilibrium measurements have been made to determine the sulfur potentials of a great many systems of metallurgical interest.' In order to confirm their reliability, to supply data which may be of use in further thermodynamic calculations, and to establish the reliability of the Knudsen orifice in obtaining accurate thermodynamic values at high temperatures, the present investigation on the pressure of the gaseous species above FeS in equilibrium with iron has been carried out. The Knudsen orifice method has been used for these pressure measurements. Experimental The apparatus and general technique for this investigation are the same as that reported for the determination of the vapor pressure of silver.' To reduce the residual gas pressure in the evacuated chamber, a titanium getter, maintained at run temperature, was introducbed. Several types of Knudsen cells were used—platinum, zircon, and fused silica. The orifice in the zircon cell was fashioned with a small diamond wheel. The same precautions were used in this investigation as were employed in the work on Mo2S2.3 The FeS-Fe mixture was prepared by heating a sample of pure FeS,, supplied by K. K. Kelley of the Bureau of Mines, with excess iron powder, cp grade, obtained from the Fisher Scientific Co. These two substances were heated in a closed Armco iron crucible at 960°C, held in a vacuum of less than 10" mm Hg for 24 hr. The mass was then removed from the cell and ground in an agate mortar. In this form it was charged to the various Knudsen cells. Heating the Knudsen cell for an additional two days was sufficient to obtain constant rates of weight loss of the cell. The data obtained in this investigation are recorded in Table I. To establish whether or not a sulfide of iron is volatile at these temperatures, 0.7646 g of the FeS-Fe mixture, described above and containing 69.2 pet Fe, was placed in the zircon Knudsen cell. Run Nos. 103 to 109 were performed on it. After the completion of these runs, the total amount of iron left in the cell was obtained by chemical analysis. It contained 0.537 g Fe, compared to 0.529 g in the original charge. Thus, there was an apparent gain in iron of 1.5 pet. This is attributed to unknown experimental error, and the conclusion is that no sulfide of iron is volatile. The vapor pressure of pure iron4 is about one thousandth that of the sulfur pressure' at these temperatures. The vapor pressure of iron inside the Knudsen cell will be almost exactly that of pure iron, since in the iron-rich phase the percentage of sulfur is of the order of 0.025 pet.At this low percentage of sulfur Henry's law is probably obeyed by the sulfur. Thus, the iron will obey Raoult's law. In any event, the vapor pressure of iron will be lower than that of pure iron and, since the vapor pressure of pure iron is negligible compared to the pressure of sulfur, the weight loss of the cell due to the vaporization of iron should be negligible. Since neither iron nor FeS is volatile to an appreciable extent, the total weight loss of the cell must be due to the vaporization of sulfur. Discussion and Calculations On the assumption that S, is the only gaseous species present in appreciable quantity, its pressure

Jan 1, 1957

By Henry J. Miller, Marcella Linderman

During some experiments made by Henry J. Miller, partly in Germany and partly in the United States, in which it was found necessary to melt metals in quantities up to 60 kg. in a vacuum or under low pressures of hydrogen, molybdenum was tried as the resistor in the electric melting furnaces. Molybdenum ribbons 16 by 0.55 mm. and 18 by 0.45 mm. were used as resistors. The furnaces were of the type shown in Fig. 1. About the heating tube, Y, are wound parallel resistors of molybdenum ribbon from the water-cooled electrodes, El, Ez. The whole is within a copper container having outlets for the removal or introduction of gases and a window, W, for observation, the space about the heating tube and electrodes being filled with insulating material. The life of the molybdenum used as the resistor was found to depend very much on the manner of using it, its failure being due in some cases to thinning by evaporation or chemical reaction and in others to hardening, which prevented it from following the expansions and shrinking of the heating tubing without cracking. As such failures are often rather expensive in commercial work, it was thought worth while to determine the causes. The factors influencing the behavior of molybdenum resistors used in this manner may be briefly stated as follows:

By V. G. Leak, R. A. Swalin

The dilhsion of silver and trace concentrations of tin in liquid silver has been rrzeasured in the temperature range from about 975° to 1350°C. The difBsion dala. fil lhe following equations: fov self-diffusion of silver The ratio of DSn to DAg is found to be about 1.34. The higher diffusivity of tin is interpreted in terms of the coullombic repulsion which results from the fact that tin dissolved in silver has a valence of +3 relative to silver. THE phenomenon of diffusion has been well-described theoretically for hard-sphere gases and solids and found to be in good agreement with experimental data for certain gases and solids. Liquid-diffusion phenomena have not been well described theoretically and there is generally a lack of good experimental data. In this investigation self-diffusion and solute diffusion in liquid silver were studied. Silver was chosen as a solvent for two main reasons. First, silver is a noble metal and the atoms are considered to have a spherically symmetric charge field; hence the liquid may be considered to be a random array of approximate hard spheres. Mercury, gallium, and other lower-melting metals were eliminated from consideration since it appears possible that in their liquid states there is some residual long-range order and directional bonding. Second, silver behaves as a monovalent solvent and, while cadmium, indium, tin, and antimony all have nearly the same atomic size, they have chemical valences relative to that of silver of +1, +2, + 3, and +4, respectively. Slifkin, Lazarus, and coworkers1-5 investigated the diffusion of these solutes in solid silver and found that their diffusion rates increased with an increase of the excess valence of the solute. In the solid state the diffusion-rate increase was calculated to be due to a change in local modulus of the solvent caused by the excess valence of the solute.1"3 For the present investigation it was planned to determine the effect of valence upon solute diffusion in liquid silver. It was deduced that a coulombic repulsion between solute and solvent might be responsible for larger volume fluctuations in the vicinity of the solute thereby enhancing the diffusion of the solute atoms. Tin was the first solute investigated and was chosen for experimental convenience. If an excess-valence diffusion effect exists in the liquid state, the solute tin with its excess valence of + 3 might show a large enough effect to distinguish it from the self-diffusion of silver in silver. The silver self-diffusion data were obviously required as a base line for comparison. In addition silver self-diffusion was investigated with a view toward examining the data in connection with the Sutherland- Einstein: Coheen-Turnbull,7 and swalin8 theories of diffusion in liquids. I) EXPERIMENTAL TECHNIQUES The diffusion coefficients for tin and silver in liquid silver were determined in separate experiments using the capillary-reservoir method of Anderson and saddingtono but following closely the experimental techniques outlined by Ma and Swa1in. The radioactive alloy bath was prepared by plating either tin-113 or silver-110 m isotope* onto 99.999 *Isotopes obtained from Oak Ridge National Laboratory. pct Ag rods.* The silver and isotope were melted *Silver obtained from Cominco Co. and mixed in a graphite crucible under a purified argon atmosphere, then outgassed for capillary filling. Some of the fused-silica capillaries were filled individually as reported by Ma and Swalin, but most were filled in a different manner. A long piece of capillary tubing was sealed off on one end and held in the system so that the open end was just above the surface of the molten alloy. The system was evacuated, the open end submerged into the alloy, and argon was admitted into the system up to atmospheric pressure. The molten alloy was forced up the capillary several inches where it solidified and was subsequently cut into segments of the proper length for diffusion annealing. The apparatus for diffusion annealing was the same as that used for capillary filling except that a Pt—Pt, 10 pct Rh therinocouple was placed in the solvent bath in order to accurately measure the temperature during the run. A diagram of the dif-

Jan 1, 1964

By Ernest F. Burchard

Fluorspar is found in most of the states from the Rocky Mountains westward, and commercial production of the mineral has been reported from Arizona, Colorado, Nevada, New Mexico, Utah and Washington. The map in Fig. 1 indicates the general distribution of many of these deposits but it is by no means complete. In the summer of 1926 the writer examined certain deposits of fluorspar in Arizona, California, Colorado, New Mexico and Washington; in November, 1927, revisited the Jamestown, Colo., district, and in earlier years examined deposits in Colorado and New Mexico. Based on notes of his own and on descriptions and other data by H. A. Aurand, H. W. Davis, R. B. Ladoo, V. C. Heikes, W. D. Johnston, Jr., and by producers of fluorspar, he prepared the following brief descriptions of deposits and estimates of reserves of fluorspar, originally for the use of the subcommittee on fluorspar of the Joint Committee on Foreign and Domestic Mining Policy and on Industrial Preparedness respectively of the Mining and Metallurgical Society of America and the American Institute of Mining and Metallurgical Engineers. Descriptions of many fluorspar deposits in various western states and districts have been published. It is not feasible to summarize this literature here, but the appended bibliography will indicate to the interested reader what papers are available. Arizona Fluorspar has been reported as occurring in Arizona in the following localities: near Duncan, Greenlee County; near Naco, Tombstone, and Paradise, Cochise County; Black Mountain, Mojave County; 25 miles southwest of Tucson, and at Helvetia and Silver Bell, Pima County; near Mammoth mine, Pinal County; in Yavapai County, 7 miles from Aguila, and in the Bradshaw Mountains; and near Dome, Yuma County. Production has come principally from the Castle Dome district, Yuma County, with minor quantities from Greenlee, Pima and Yavapai counties. The writer examined deposits in the Castle Dome district, Yuma

Jan 1, 1934

By J. Chipman, J. A. Cordier

Equilibrium in the reaction H2 (g) + 2 = H2S (g) was studied at 1600°C for sulphur dissolved in Fe-Ni alloys of 0 to 100 pct Ni. Within experimental accuracy, the equilibrium ratio pH2s/pH2 [pct S] is independent of the Fe-Ni ratio. Its variation with sulphur content is the same in nickel and the alloys as in iron. Recent data on dissociation of S2 into atomic sulphur are used to apply a small correction to earlier equilibrium data. Equations are presented which define the thermodynamic properties of sulphur in liquid Fe-Ni alloys. ACTIVITY of sulphur in liquid iron was determined by Sherman, Elvander, and Chipman.' The effects of a number of alloying elements on the activity of sulphur also have been determined, that of silicon by Morris and Williams,2 that of carbon by Morris and Buehl,8 and the effects of manganese, phosphorus, and aluminum by Sherman and Chip-man.' The data of Rosenqvist and Cox5 have been used to establish the effect of copper. A summary of all of these data is included in the paper by Sherman and Chipman. In each case, the experimental method depended upon the study of equilibruim in the reaction of sulphur in the liquid metal with hydrogen gas to form H,S. Despite wide differences in the design of apparatus used by the several investigators, all of the results are in excellent agreement. Experimental Study Since the experimental method has already been described,' it will be sufficient to mention its general

Jan 1, 1956

By E. T. Turkdogan

The activities of SiO2, FeO, and Fe2O3 are calculated from previous experimental data on the activity of oxygen in Fe-Si-O melts at 1550°C. Using the oxide-activity data, the free energy of formation of fayalite from its oxides is evaluated for 1550°C. A number of investigators1-4 contributed to the study of the state of oxidation of iron in SiO,-FeO-Fe,O3 melts and the phase equilibria in the system Fe-Si-O. In a more detailed study, Schuhmann and Ensio5 and Michal and Schuhmann% easured the state of equilibrium in the SiO,-FeO-Fe,O3 melts saturated with y-iron or silica or both under low-oxygen potentials and within the temperature range 1250" to 1350°C. Similar measurements were also made by Turkdogan and Bills7,' over wide ranges of composition and oxygen potentials at 1550"C. Using the experimental data on the oxygen activities in the ternary system, Schuhmann' calculated the activities of silica and ferrous oxide in Si0,-FeO-Fe2O3 melts for 1350°C. Adequate knowledge on the activities of the constituent oxides of melts is essential in the study of reaction-equilibria and reaction-kinetics in oxide-melts. With this in view, the activities of oxides in SiO2-FeO-Fe2O3 melts at 1550°C are computed using the experimental data of Turkdogan and Bills7'8 on the oxygen activities in these melts.

Jan 1, 1962

By J. E. Powers, T. D. Taylor, N. E. Wood

A computer program has been developed to simulate a gas transmission 1ine operating under transient conditions. The program was developed by application of the basic mass and momentum balance equations. The nonlinear equations thus obtained were transformed by the method of characteristics and finite-difference techniques to make them suitable for machine computation. Three tests of the computer program were made. In each of these, the initial condition was assumed to be steady-state flow, the inlet density was held constant at the initial condition, and the outlet mass flow rate was varied with time. One test was theoretical in nature, but the others were made for direct comparison with actual field data. Results of the tests are presented in graphical form. INTRODUCTION Theoretical investigations of the transient flow of gas in long pipelines have been limited in number. In 1951, Olds and Sage4 developed a gaphical method of solving the nonlinear flow equations describing transient gas flow in a long pipeline. Research in this field at the U. of Oklahoma was initiated by Nelson1 in 1956. Nelson utilized a computer to solve numerical equations involving a lengthy trial-and-error procedure, and his results have been reported in the literature? It does not seem likely that Nelson's method can be extended to the analysis of transient behavior of pipeline networks; therefore, the investigation to be discussed in this paper was undertaken to improve and extend the previous work. The following discussion presents, briefly: (1) the basic differential equations governing transient flow, (2) transformation of these equations into a form suitable for machine computation. (3) role of boundary conditions in the calculations, (4) a very brief description of the computer program which was developed to simulate the pipeline and (5) results of tests of the computer program.

By R. A. Swalin

IN this paper, the results of an investigation concerning the diffusion of three elements, magnesium, silicon, and molybdenum, in nickel are presented. The work represents a continuation of a diffusion program relating to solute diffusion in nickel. The program has the dual aim of obtaining useful diffusion data and of yielding insight into the factors governing solute diffusion in close-packed metals. The first paper of this series has been published earlier? In both investigations, in agreement with recent results from other laboratories, the activation energies for solute diffusion were found to be close but not identical to that of self-diffusion in the pure solvent in question. In order to obtain valid diffusion data, certain experimental pitfalls recognized only in recent years had to be avoided. Chief among these were the necessity for minimizing short-circuiting diffusion paths such as grain boundaries and the necessity for using low solute concentration gradients. In this series of investigations the following precautions were taken in an attempt to minimize such errors. 1) Samples with large grain sizes, 0.5 to 10 mm, were prepared. 2) The diffusion coefficients were measured at relatively high temperatures, since imperfections such as dislocations play a less important role at such temperatures than at lower temperatures. 3) Alloys containing less than 1 atomic pct were chosen for study. Experimental Work Materials—A diffusion couple technique was employed in the experimental investigation. Briefly, this technique consisted of the following. A diffusion couple was fabricated by placing a flat face of a cylindrically shaped alloy disk against a similar face of a pure nickel disk, and a bond was formed at an intermediate temperature under pressure. The diffusion couple thus fabricated was subjected to a diffusion anneal at higher temperatures for a measured period of time and then sectioned perpendicular to the direction of diffusion. After analyzing the sections for solute concentration the diffusion coefficient was determined from a probability, plot of concentration vs distance from the diffusion interface. Vacuum melted Mond nickel was used in the experimental program. The chemical analysis of this nickel is listed in Table I. Alloys used were prepared

Jan 1, 1958

By P. R. Martin, R. B. Kelly

Drilling in Central Texas during 1933 was confined, for the most part, to the search for new serpentine plugs. Bastrop County led in this particular activity, with 50 completions during the 12 months' period, 12 of which were productive. Only one new field was opened in Central Texas during the year, it being known as "Hilbig" (Bastrop County) and was discovered by the Humble Oil & Refining Co. The finding of commercial production in the serpentine at 2500 ft. led to further search in this and surrounding counties, but without success. Bexar County actually provided the greatest amount of drilling but the activity was limited to shallow development from 400 to 2000 ft. The Edwards limestone pay, which has been such a factor in past years, received but slight attention during 1933. Unsuccessful exploration was carried on in Lee and Burleson counties. With the exception of Freestone County, the Woodbine sand area was given even less consideration. This county, because of its close proximity to Anderson and Leon counties, saw a very active leasing campaign and several important tests drilled. In Central Texas, 252 wells were completed in 1933, and of this number 52, or 21 per cent, were productive. Hilbig Field The discovery well, Humble Oil & Refining Company's Annie Hassler No. 1, was completed Feb. 16, 1933, for an initial production of 65 bbl. the first hour, through tubing and 1/2-in. choke. The production was found in serpentine at 2468 ft. and tested 37.2" A.P.I. gravity. Twelve producing wells were drilled during the year and served to indicate that not more than 300 acres would comprise the entire field. Daily production at the end of the year was 775 bbl., although the field potential was 18,240 bbl. daily through 1-in. choke. The field adapts itself to pressure maintenance, and this scientific handling is being undertaken by the Humble Oil & Refining Co. through one injection well. It is the only area in the district where work of this nature is under way. Proration of Oil The more stringent application of proration in 1933 did not affect materially the producing fields in Central Texas. This is accounted for

Jan 1, 1934

By Allan Martin, R. A. Swalin

Diffusion rates of manganese, aluminum, titanium, and tungsten in nickel were measured at temperatures between 1100° and 1300°C. Activation energies, Q, and values of the frequency factor, Do, were calculated for each system. Values of Q were found to be within 15 pet of that for self-diffusion of nickel in agreement with present theories of diffusion. ONE of the most interesting problems in diffusion concerns factors governing the order of diffusion coefficients of various solutes in a common solvent metal at low solute concentrations. An early suggestion by Rhines and Mehl' was that diffusion coefficients might each approach that of the self-diffusion coefficient of the solvent itself. Later Thomas and Birchenall' pointed out correlations between the order of the diffusion coefficients and the freezing point depressions of the solvent by the various solutes. Other correlations have been sought. To settle this question it seems likely that much more data will be needed and, in particular, data collected at low solute concentrations. This type can be obtained by special analytical techniques as well as by use of radioactive tracers. The following study was made of diffusion of manganese, aluminum, titanium, and tungsten in a common solvent, nickel, at relatively low solute concentrations: 1—Production of alloys of nickel with manganese, aluminum, titanium. and tungsten at concentrations of the order of 1 atomic pet. 2—Use of pressure-welded diffusion couples in cylindrical form. 3—Diffusion anneals in the temperature range of 1100" to 1300°C. 4—Lathe sectioning of the diffused couples. 5—Spectrophotometric analyses of lathe turnings for the solute being studied. 6—Calculation of the diffusion coefficient for each of the solutes as a function of temperature. 7—Interpretation of results with current theories of diffusion. Experimental Work Materials—Two types of nickel were used in this research. The grade designated as Vacuum melted Mond nickel was used for all diffusion systems except the Mn-Ni system for which the Vacuum melted electrolytic nickel was used. Analyses of the two grades are given in Table I. The manganese used in making alloys was 99.9 + pet pure, aluminum 99.99 pet pure, titanium 99.9 pet pure, and tungsten of C.P. grade powder. Alloys used in this investigation were prepared by melting in vacuo or under a low pressure of argon. After melting, all heats except those of nickel-manganese were poured into a cylindrical copper mold 3 in. long and 1 in. ID. In the case of nickel-manganese, the alloys were solidified in the melting crucible. For nickel-aluminum heats alumina crucibles were used and for all other heats, zirconia crucibles.

Jan 1, 1957

By H. C. Burghard, F. R. Brotzen

Experiments were performed to determine the effects of mechanical vibrations on ordering in CuAu. The effects of 5, 10, and 15 kc vibrations were investigated over a range of ordering temperatures of 280° to 360°C. A decrease in the rate of ordering was observed at all frequencies and ordering temperatures. THE effects of mechanical vibrations on certain solid-state reactions have been noted by several investigators. In 1930, Mahoux' reported a substantial increase in the case depth of a steel sample nitrided under the influence of mechanical vibrations over that of an unvibrated sample. Similarly, an accelerating effect of vibrations on the diffusion of chromium in steel was noted. Guillet, in the same year, confirmed the results of Mahoux. More recently Schenck and schmidtmann3 studied the effects of low-frequency, alternating loads on the diffusion of carbon in steel. The results of their experiments, conducted at 500 cycles per min and large strain, (0.2 pct), indicated an acceleration of the process. These workers also reported an increase in case depth of a sample vibrated at 430 kc during a carburizing treatment. Effects of high-frequency vibrations on solid-state reactions have also been investigated by Gudzoff and Gavze6 and Fairbanks and Dewez.7 The former reported an acceleration of the age-hardening process in aluminum alloys. The latter noted changes in the structure and mechanical properties of steel annealed under the influence of vibrations. On the other hand, Altenburg4 and Ehringer5 have given some theoretical reasons and experimental evidence as to the improbability of any effect of vibrations on diffusion. Comprehensive surveys of the effects of vibrations on metallurgical reactions are given by Hiedemann' and Bergmann.9 None of the above investigations led to a physical description of the effects of mechanical vibrations on solid-state reactions. In the present study an attempt was made to gain an understanding of the influence of vibrations on nucleation and diffusion. The order-disorder transformation was chosen for investigation since its mechanism has been extensively discussed in the literature. Moreover, the progress of the transformation may be easily followed by observation of electrical resistance changes. EXPERIMENTAL PROCEDURE The specimens used for the experimental observation of ordering rates were prepared from 50 at. pct Cu-Au alloy wire.* Each specimen consisted of a 0.02-in. diam wire approximately 10 in. long to which two copper potential leads were silver soldered, 2 1/2 in. apart, near one end of the wire. A 1/8-in. diam by 1/4-in. long steel stub was silver soldered

Jan 1, 1960

By B. M. Larsen, T. E. Brower

IN an earlier paper1 we discussed a simple, rapid method of taking samples of liquid steel and analyzing them for oxygen, which, though possibly not absolutely accurate (as is likewise true of all other methods), certainly yields results that are satisfactorily consistent. Accordingly, samples from hundreds of heats in different shops were analyzed for oxygen, with results sufficient in number to be handled statistically and permit estimation of some general trends. Measurements were made in acid as well as in basic open hearths, throughout the refining period, to learn how stirring, blocking, adding ore or lime or sand, affects the oxygen content of the bath; we also followed the changes brought about by tapping, teeming, and deoxidizing. Some of these results, discussed in an earlier paper.2 bring out the dominant role of the carbon-oxygen reaction in regulating degree of oxidation both of metal and of slag, also the marked variability of concentration of dissolved oxygen [0] in excess of that which would be in equilibrium with carbon and with carbon monoxide at a partial pressure of one atmosphere. As a logical beginning on this complex problem, we take up in the present paper the variability of this excess oxygen, ?[O], when other factors are as constant as they ever are in open-hearth operation; namely, toward the end of the refining period, when the bath may be regarded as in the comparatively steady state it approaches in absence of disturbing factors. This condition was chosen because by that time the significant reactions, except carbon oxidation, between slag and metal have come to substantial equilibrium; this facilitates interpretation of the complex situation and thus permits more definite conclusions to be drawn. This excess concentration of oxygen, ?[0], in the metal is needed, of course, to make the steelmaking process go at a reasonable rate; alternatively it may be regarded as a measure of the virtual pressure increment above one atmosphere, or of the degree of supersaturation, of carbon monoxide in the metal. According to our measurements, the excess concentration ?[O] in liquid steel varies from about 0.009 to 0.035 per cent oxygen by weight. It is quite sensitive to change of conditions, being altered temporarily by operations such as stirring with green poles, additions of ore, lime, or sand; but as the disturbance works itself out, it resumes a level within the intermediate range characteristic of the steady state. The conditions most common in average furnace practice are covered by the following : [ ] as in a reasonably steady state-that is, when it is boiling normally, is at proper temperature with a well-shaped slag, and has been free from disturbing effects during the preceding half hour-?[O] returns from

Jan 1, 1946

AS I told you in the chapter on salts, saltpeter is a mixture composed of many substances extracted with fire- and water from arid and manurial soils, from that growth which exudes from new walls or from that loosened soil that is found in tombs or uninhabited caves where the rain cannot enter. It is my belief that it is engendered in these soils from an airy moisture that is drunk in and absorbed by the earthy dryness. Considering its effects, I do not know how to decide and say exactly what the nature of saltpeter is. The learned and very wise physicians find it salty and with a subtle sharpness both in taste and in their medical experiments. Considering its strong biting qualities, they decide to say that it is of a hot and dry nature; on the other hand when they see that it is engendered from the air and that when touched by fire it becomes inflammable and vaporous, and rises with a fearful impetus when mixed in powder for military guns, it manifestly shows itself to be of a hot and moist airy nature. And then when they see that it is shining and transparent with whiteness and is fusible in every fire in a manner corresponding to a thing of a watery nature, and since it. is heavy, it seems that it can be said to be watery in nature. To this is added the experience of touch and of the great cooling action which it has on water in summertime when wine is to be cooled, and since it crushes and breaks with but little pressure, it might be thought to be earthy in nature; especially when it is seen to change into a hard, white stone when burned with an equal amount of sulphur. Thus it seems that every one of the elemental qualities is predominant in it. Now the ancients called this, or a similar thing, nitrum. [150] Pliny, in Book XXXI of his Natural History, has said that it was a thing not much different from salt, that doctors do not seem to have yet known its nature, that it is found in various places, and that the best is found in Macedonia. But among the moderns and especially in our regions, it is not known today what it is that Pliny and other writers refer -to, since according to the aforesaid Pliny and other ancient writers it is a natural mineral. Some say that in place of, the natural kind the artificial will serve for the same medicinal purposes, since it has the same nature and is perhaps more powerful.

Jan 1, 1942

By M. C. Leverett

Knowledge of the theory underlying the behavior of mixtures of fluids in reservoir rocks is essential to the proper solution of certain types of problems in petroleum production, but is as yet incompletely developed. The object of this paper is to show the application of well established thermody-namic and physical principles to these problems, and thus to assist in the development of the basic theory. For convenience the problems to be considered here may be divided into two groups: 1. Static problems, involving only the static balance between capillary forces and those due to the difference in densities of the fluids; i.e., gravitational forces. 2. Dynamic problems, involving analysis of the motion oi mixtures of immiscible fluids in porous media under the influence of forces due to gravity, capillarity, and an impressed external pressure differential. Capillary Equilbrium in Sands Under this heading the static type of problem will be discussed and the results of experimental investigations on the capillary properties of unconsolidated sands will be presented. Although the discussion of this section is, in a sense, prefatory to the treatment of problems of mixture flow, the concepts developed here have considerable intrinsic importance apart from their ap-plication to flow problems. For, it is reason-able to postulate that the reservoir fluids are, owing to their long existence in undis- turbed mutual contact prior to exploitation, in substantial equilibrium. It follows that their distribution in the reservoir at the time of tapping should be entirely predictable from the theory of capillary equi librium, provided certain experimentally measurable properties of the reservoir rock are known. Knowledge of the distribution of the several fluids in the reservoir is, ol course, helpful in the estimation of reserves and in other problems. It is to be emphasized that throughout the discussion of capillary statics it is assumed that the fluids are in equilibrium from the capillary standpoint. Thus, water, where it is referred to as being in a reservoir, will be understood to be interstitial water, present at the time of drilling the reservoir, commonly termed "connate" water. The theory developed here is perfectly general for any porous solid, whether a carefully prepared unconsolidated sand or a natural sandstone from an oil reservoir. At present, however, only problems involving clean, unconsolidated sands can be made to yield numerical solutions, since only such sands have been adequately investigated experimentally. Experimental evaluation of the pertinent properties 01 natural reservoir rocks will permit the extension of the numerical treatment to problems involving these materials. We shall now consider in some detail the static equilibrium of fluid mixtures in porous solids: that is, the manner in which the reservoir fluids are distributed vertically whell the Forces due to capillarity are just balanccd by those due to gravitation.

Jan 1, 1941

By M. C. Leverett

Knowledge of the theory underlying the behavior of mixtures of fluids in reservoir rocks is essential to the proper solution of certain types of problems in petroleum production, but is as yet incompletely developed. The object of this paper is to show the application of well established thermody-namic and physical principles to these problems, and thus to assist in the development of the basic theory. For convenience the problems to be considered here may be divided into two groups: 1. Static problems, involving only the static balance between capillary forces and those due to the difference in densities of the fluids; i.e., gravitational forces. 2. Dynamic problems, involving analysis of the motion oi mixtures of immiscible fluids in porous media under the influence of forces due to gravity, capillarity, and an impressed external pressure differential. Capillary Equilbrium in Sands Under this heading the static type of problem will be discussed and the results of experimental investigations on the capillary properties of unconsolidated sands will be presented. Although the discussion of this section is, in a sense, prefatory to the treatment of problems of mixture flow, the concepts developed here have considerable intrinsic importance apart from their ap-plication to flow problems. For, it is reason-able to postulate that the reservoir fluids are, owing to their long existence in undis- turbed mutual contact prior to exploitation, in substantial equilibrium. It follows that their distribution in the reservoir at the time of tapping should be entirely predictable from the theory of capillary equi librium, provided certain experimentally measurable properties of the reservoir rock are known. Knowledge of the distribution of the several fluids in the reservoir is, ol course, helpful in the estimation of reserves and in other problems. It is to be emphasized that throughout the discussion of capillary statics it is assumed that the fluids are in equilibrium from the capillary standpoint. Thus, water, where it is referred to as being in a reservoir, will be understood to be interstitial water, present at the time of drilling the reservoir, commonly termed "connate" water. The theory developed here is perfectly general for any porous solid, whether a carefully prepared unconsolidated sand or a natural sandstone from an oil reservoir. At present, however, only problems involving clean, unconsolidated sands can be made to yield numerical solutions, since only such sands have been adequately investigated experimentally. Experimental evaluation of the pertinent properties 01 natural reservoir rocks will permit the extension of the numerical treatment to problems involving these materials. We shall now consider in some detail the static equilibrium of fluid mixtures in porous solids: that is, the manner in which the reservoir fluids are distributed vertically whell the Forces due to capillarity are just balanccd by those due to gravitation.

Jan 1, 1941

By R. C. Edwards, T. G. Kirkland, Will Mitchell

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, T. G. Kirkland, Will Mitchell

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953