Search Documents

By M. P. Tixier, A. Poupon, M. E. Loy

Simple qualitative methods are explained for identifying those shaly sands in a well that are most likely to contain oil. A need for more precise measurement of the variables that enter shaly sand analysis is indicated. Field examples are given to illustrate the methods. A theoretical discussion of the quantitative interpretation of shaly sands is given as a basis for discussion and as a guide for the future. While not generally capable of practical application at the present time because of the lack of sufficient accuracy of the electric log data, these methods may become more feasible in the future as the result of the improved logging methods now being introduced. INTRODUCTION Experience has shown that for porous formations containing only a negligible amount of clayey material, reliable information on the fluid saturation and porosity of the reservoir rocks can usually be derived from the electrical logs. The interpretation is based on empirical formulae relating the true resistivity of a porous formation to its lithologic character, to the resistivity of the interstitial water, and to the proportions of water and hydrocarbons in the pores.' If the resistivity of the interstitial water is not known, its approximate value can be derived from the SP curve.2,3 The porosity can usually be determined to a good approximation from a MicroLog, or a MicroLaterolog.4,5 When the reservoir rocks contain an appreciable percentage of clayey material, an additional factor is introduced into the analysis. In a clean formation, the matrix is an electrical insulator, so that the ability of the formation to conduct current is due only to the conductivity of the electrolytes in the pores; in a shaly formation, the shale constitutes a part of the rock matrix able to conduct current, and influences the resistivity of the formation. On the other hand, the spontaneous emf's and the circulation of the SP currents are also responsive to the presence of the shaly material. All other factors being the same, the deflection of the SP curve opposite a shaly permeable formation is smaller than the deflection which would be observed if the formation were clean. The effects of the presence of shale on the resistivity and on the SP curves in a shaly formation are functions of the amount, of the specific resistivity, and of the geometrical distribution of the shaly material within the formation. The presence of shale therefore constitutes an important complication in electrical log interpretation. It is easy to realize, for example, that the presence of a large amount of clayey material in a sand may have such a predominant effect that the resistivity of the sand will not change very much, whether the pores are entirely filled with connate water, or contain a high saturation of hydrocarbons. Important research projects have been undertaken to investigate the influence of shales and to find a way to allow for this influence in the interpretation of a log. The problem of the SP in shaly sands was analyzed mathematically by H. G. Doll"' for the case of sands with shale laminations. Formulae expressing the resistivity of shaly formations were proposed by Patnode and Wyllie8 and de Witte.9 Other quite interesting theoretical and experimental results have been published by various authors.l0,ll,12,l3,14 The purpose of the present paper is to discuss an approach to electrical log interpretation in shaly sands. This approach is based partly on some of the theoretical and experimental data available in the literature and partly on observations made on actual field logs. Comparatively simple methods for qualitative and semi-quantitative analysis are described. These methods depend principally upon information provided by the electrical logs.

Jan 1, 1955

By M. A. Dayananda, R. E. Grace

Vapor-solid diffusion couples were employed in a study of ternary diffusion in the single-phase copper-rich corner of the Cu-Zn-Mn system Interdiffusion coefficients were measured at three different compositions corresponding to the intersections of diffusion paths determined at 850°C. Intrinsic diffusion coefficients were determined at two compositions by the Philibert-Guy method. New relations between the various intrinsic diffusion coefficients are also presented. MOST of the investigations of ternary diffusion have been made with "sandwich" couples formed by welding together two homogeneous solid solutions with or without markers placed at the interface. With such couples Kirkaldy and his coworkers1,2 have determined interdiffusion coefficients which describe ternary diffusion in the substitutional alloy systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy3 have reported intrinsic diffusion coefficients for Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.4 The use of semi-infinite diffusion couples, for example, vapor-solid couples, where the diffusing species are supplied from a vapor source in contact with a diffusion disk, has so far been confined to studies of binary diffusion. Balluffi et a1.5,6 have successfully determined the interdiffusion as well as the intrinsic diffusion coefficients in several binary metallic systems employing vapor-solid couples with markers initially placed at the vapor-solid interface. They have also discussed the general advantages and limitations of such couples. Vapor-solid diffusion couples can successfully be employed in ternary diffusion studies. The importance of such couples in ternary diffusion lies in the fact that inert markers lie close to the vapor-solid interface, and the composition of the marker plane is virtually known before experimentation begins. Another minor advantage is that the method of Philibert and Guy4 may be used with three alloys instead of four. Lastly, the diffusion paths need not be S-shaped, as pointed out by Meijering7 for "sandwich" couples. The Cu-Zn-Mn system is convenient for ternary diffusion studies because of the large single-phase field in the copper-rich corner. The vapor pressure of zinc above such alloys is known, and X-ray measurements indicate that the molar volume is nearly constant over a wide range of compositions.8,9 It is the purpose of this paper a) to extend the analysis of Balluffi and seigle5 to permit an evaluation of interdiffusion coefficients in ternary vapor-solid couples, b) to use the method of Philibert and Guy to determine intrinsic diffusion coefficients with such couples, and c) to present experimental data on both interdiffusion and intrinsic diffusion coefficients for the Cu-Zn-Mn system at 850°C. INTERDIFFUSION IN TERNARY VAPOR-SOLID COUPLES The analysis of Balluffi and seigle5 is extended in this section to a vapor-solid couple where two solutes diffuse from a vapor source into a ternary solid solution. To take into account the expansion of the diffusion disk caused by the absorption of mass from the vapor phase, the total fluxes are expressed on the basis of a coordinate system that moves with the velocity of the vapor-solid interface; thus. where D3ij are the intrinsic diffusion coefficients,4 v(x, t) is the local Kirkendall velocity of mass flow, and F(t) is the negative velocity of the vapor-solid interface (x = 0). Both these velocities are based on a fixed coordinate system far removed from the diffusion zone. Using the continuity relations and Darken's method1' for a ternary system in which components 1 and 2 diffuse from the vapor phase into a solid of negligible vapor pressure, one obtains

Jan 1, 1965

By Thomas M. Drown

ZING is, as is well known, very brittle at a temperature of about 210' C. (410' F.), and may then be readily pulverized in a mortar. By sifting it may be obtained of uniform grain. I have been accustomed to prepare products passing through 40, 60, and 80-mesh sieves, and also by bolting through a fine handkerchief. The principal analytical uses to which I have hitherto applied this material are to the reduction of iron directly from the ore by heating it with the pulverized zinc, and the reduction of ferric to ferrous compounds in solution. In the first case the pulverized ore, 0.5 gram or less, is intimately mixed with about ten times its weight of the pulverized zinc (the finer the zinc the better), in a porcelain crucible, and this mixture is covered with about the same amount of zinc. The crncible is then heated at the top of the flame of a Bunsen bhrner, at a dull red heat, for about ten minutes. The crucible should not be covered. When cool, the crucible, with its contents, is placed in a flask treated with hot dilute sulphuric acid, and brought quickly to a boil. The zinc and reduced iron are dissolved in a few minutes and the flask is then tightly corked and allowed to cool. When cool, the iron is directly titrated by potassium permanganate.

Jan 1, 1879

By Carl Henrich

A.. S. DWIGHT, New York, N. Y.-Mr. Henrich's paper is rather inconclusive as to the role that alumina really plays in slags. He gives a number of interesting instances of high alumina, with conclusions that he draws from the analyses, in the light of what he knows of the accompanying conditions, but the information given is hardly sufficient to permit intelligent criticism of these conclusions, for it is well known that the slag composition is not the only factor that can produce some of the furnace results favorable or disastrous, as the case may be, which he records. As a matter of fact, most metallurgists who have wrestled with this problem in connection with the smelting of lead and copper ores, usually arrived at some sort of a working hypothesis which met the local conditions fairly well, and then, being busy men, were inclined 'to leave the theoretical question very much as Mr: Henrich leaves it when he says: "A question with which I purpose dealing at some future time." It is unfortunate that in the Golden Age of the smelting industry in the West, when we were all dealing with large tonnages of complex ores, often containing large percentages of alumina in combination with other. refractory elements, the smelting companies were not generally equipped for research as they are today, and much experience that might have been,

Jan 4, 1917

By W. H. Justice

Cycling operations have been successfully conducted in the La Gloria Zone for eight years. The cycling of this zone is now virtually completed. It is proposed that this report shall review the cycling operations of this reservoir so that the industry can more accurately evaluate the cycling process as a production method. The La Gloria project is one of the largest cycling operations in the State of Texas. The gas rights in the field are unitized in three operating units. By mutual agreement Magnolia Petroleum is the designated operator of the project for the 12 operators owning the gas rights. The La Gloria Corp, is the owner and operator of the cycling plant. The development and operation of the field are under the direction of an Operators Committee comprised of a representative of each operator. The Operators Committee is assisted by an Engineering and Geological Sub-Committee. The La Gloria gas field is situated approximately three miles north of Fal-furrias, Tex., and lies principally in the extreme south end of Jim Wells County, with its outer limits extending into the north end of Brookes County, Tex. It is a simple elliptically-shaped dome which has a closure of 350 ft. The field encompasses a surface area of 5,500 acres. The gas reserves are found in 20

Jan 1, 1950

By R. J. Borg, C. E. Birchenall

Vapor pressures of eight compositions of Mg-Cd have been determined by the Knudsen effusion technique. Measurements are made at several temperatures for each alloy and the results interpolated to a common temperature for the calculation of the activities. It is not possible to obtain values for the partial molar enthalpies because of the narrow temperature range spanned by the measurements. The results show less precision than those obtained for pure Cd which are also reborted. These alloys are extremely susceptible to corrosion which provides a possible explanation for the lack of precision. Nevertheless, the values of the activity are in good agreement with the results of electromotive force measurements previously reported for the Mg-Cd system. MAGNESIUM and cadmium are mutually soluble in all proportions in the solid state and form a single phase which has the hexagonal close-packed structure. X-ray investigations of this system1,2 have revealed a rapid variation in the relative dimensions of the unit cell occurring at approximately 50 at. pct. The rate of change of the c/a ratio with composition increases markedly for alloys containing more than 50 at. pct Cd. The purpose of this investigation was to determine the activity of Cd in the neighborhood of 50 at. pct and to discover whether or not the thermo-dynamic properties undergo a similar rapid change. The activities are calculated from vapor pressure data obtained by the Knudsen effusion method. Unfortunately the precision of the data from which the thermodynamic values are calculated is insufficient to establish unequivocally a departure from the normal trend. The results are reported primarily because they substantiate the only previously reported activity measurements3 and because they include values for pure Cd which in contrast to those of the alloys show excellent precision. The Cd-Mg system is known to contain several ordered phases. However, this investigation was made at temperatures considerably above the transition temperatures, and the alloys may be regarded as nearly random solid solutions. EXPERIMENTAL Apparatus—The effusion cells are machined from solid tantalum rod. The lids consist of threaded, flanged rings of tantalum onto which are welded shallow cups of 4 mil molybdenum foil. The orifice, which is located at its center, is made by grinding off a small dimple produced with a sharpened punch. Such an orifice has been mounted in plastic, sectioned, and the thickness of the orifice edge measured in a microscope. The maximum thickness is 0.00016 in., and the Clausing factor is consequently equated to unity. The area of the orifice is determined by tracing its projection on the screen of the metallograph at a known magnification and measuring the area of the tracing with a planimeter. Excellent temperature control is achieved with a 4 by 18-in. alundum core, gradient-wound, furnace

Jan 1, 1960

By R. J. Burgess, A. R. Ramey, A. R. Adams

During interpretation of pressure buildup tests on gas wells in a tight dolomite gas reservoir, peculiar behavior was noticed. Two straight lines were apparent. Effective permeability to gas taken from either straight line was about the same, and the Miller-Dyes-Hutchinson dimensionless time check for the straight line was proper for both straight lines. Geological data indicated the likelihood of scattered trending fractures in the reservoirs. Since the first straight Iine yielded permeability values close to the geometric mean permeability from core analyses, it was postulated that the reservoir model was that of an acidized well completed in the tight dolomite, but that widely scattered hairline fractures caused the mean permeability of the reservoir distant from the well to be higher than the matrix permeability. Because all other studies of fractured reservoirs to the authors' knowledge assumed that the fracture matrix was dense enough to communicate directly with the well, no interpretative methods were available. The Hurst line-source solution for a radial change in permeability for interference between oil reservoirs was adapted to pressure buildup testing. The result indicated that the first straight line should yield the proper matrix permeability and wellbore skin effect. The second straight line may be extrapolated to obtain static pressure. The time of bend between the straight lines was used to estimate distance to a fracture. Application to field test data is shown. It is believed that the methods developed and the case history presented will add to present tools available for pressure buildup interpretation. Introduction Since the pioneer studies by Miller, Dyes, and Hutchin-son1 and Horner' in 1950 and 1951, well test analysis has become recognized as one of the most powerful tools available to both production and reservoir engineers. Well test analysis serves as a logical basis for well stimulation and completion analysis, and for long-term reservoir engineering. Since the early 19501s, much effort has been placed on the development of well-test analytical methods. Reservoir and well conditions of increasing complexity have been considered systematically to provide the analyst with a catalog of causes and effects. Matthews and Russella state that some 200 papers dealing with this subject have been published in the last 35 years. Developments in well test analysis appear to have originated in one of two ways. Either a physically realistic field condition was anticipated and analytical solutions for the condition achieved, or anomalous field test behavior was recognized and interpretative methods sought for the anomaly. In recent years, it has appeared that the latter has inspired an increasing number of studies. The analyst today finds an increasing number of known cause and effect studies available for well test analysis, the classic of which is that of finding the specific flow problem that generated the answer — the well behavior. Although it may be impossible to achieve this goal uniquely, the analyst often is able to select a useful interpretation that combines all known performance and geologic data — or to show that various logical alternatives would not significantly affect the interpretation. During a recent reservoir study, we observed gas well test behavior that did not appear to fit behavior described previously. Although it cannot be said that we have found a unique interpretation, we shall present in this paper the peculiar behavior observed, and describe the reservoir and interpretative methods developed. Reservoir Description The subject gas reservoir is a 9-mile-long, narrow dolomite reservoir lying within a limestone of Ordovician age. (See Fig. 1.) The dolomitized rock in the field consists of dark brown to buff, dense to coarsely crystalline, vugular dolomite containing numerous hairline fractures, many of which may have been closed in the reservoir and parted when cores were brought to the surface. Larger fractures are also apparent in core, but usually are filled and sealed with euhedral dolomite crystals. Portions of the north flank of the reservoir are known to be cut by a sealing fault downthrown to the north. Gas wells located near the fault have higher open flow potentials than those more distant from the fault. This is believed to be a result of higher permeability near the fault due to more extensive and open fractures. Detailed coring and core analysis have been performed on several of the wells in this reservoir. Fig. 2 presents permeability variation' plots for both horizontal and vertical

Jan 1, 1969

By C. E. Cottrell, G. W. Preckshot, N. D. Delisle, D. L. Katz

Most crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir. mechanisms. Asphalt has been the subject of widespread investigation but, owing to the complexity of the substances being considered, progress has been slow. Investigators working primarily with the asphaltic substances have treated the subject from the colloidal standpoint and have developed theories that picture the asphaltic particles as surrounded by adsorbed materia1s.14,15,17,24 The deasphaltization of lubricating oil by the use of solvents treats the subject primarily from the standpoint of liquid-liquid equilibria.'' A complete understanding of asphaltic substances would make possible the following of the material from its initial state in the crude oil through precipitation processes to the final plastic stage, the most common form of which is used in asphaltic pavements. Since these asphaltic particles are very small, it appears 'hat the electron microscope4 might be a useful tool in studying the precipitation processes. Specimens are examined by the electron microscope in a vacuum and as very thin films, requiring special techniques in preparation of samples. A brief description of the electron microscope and its operation will bring out the difficulties and advantages of its use for this problem. The first work was done with crude oils that had been diluted with solvents for the preparation of the film to be examined. Later a technique was developed by which the undiluted oil film could be made thin enough for direct examination. These two techniques show vastly different results Asphaltic particles have been precipitated from crude oils by a variety of

Jan 1, 1943

By G. W. Preckshot, C. E. Cottrell, D. L. Katz, N. D. Delisle

Most crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir. mechanisms. Asphalt has been the subject of widespread investigation but, owing to the complexity of the substances being considered, progress has been slow. Investigators working primarily with the asphaltic substances have treated the subject from the colloidal standpoint and have developed theories that picture the asphaltic particles as surrounded by adsorbed materia1s.14,15,17,24 The deasphaltization of lubricating oil by the use of solvents treats the subject primarily from the standpoint of liquid-liquid equilibria.'' A complete understanding of asphaltic substances would make possible the following of the material from its initial state in the crude oil through precipitation processes to the final plastic stage, the most common form of which is used in asphaltic pavements. Since these asphaltic particles are very small, it appears 'hat the electron microscope4 might be a useful tool in studying the precipitation processes. Specimens are examined by the electron microscope in a vacuum and as very thin films, requiring special techniques in preparation of samples. A brief description of the electron microscope and its operation will bring out the difficulties and advantages of its use for this problem. The first work was done with crude oils that had been diluted with solvents for the preparation of the film to be examined. Later a technique was developed by which the undiluted oil film could be made thin enough for direct examination. These two techniques show vastly different results Asphaltic particles have been precipitated from crude oils by a variety of

Jan 1, 1943

By H. Rush Spedden, Arvid Thunaes

Pilot plant test work in 1942 and 1943 showed that by a combination of desliming, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants.

Jan 8, 1950

By Charles Catlett

AN examination of the census reports' for 1880, which contain a large number of complete analyses of typical American iron-ores, indicates that the existence of barium sulphate in intimate association with iron-ore is rather unusual. Of 94 analyses reported there, but four show any barium sulphate, and the maximum content amounts to 3.04 per cent. The note of the occurrence of considerable quantities of barite in connection with certain iron-ores found in the Pinar del Rio Province of Cuba may be of interest. These deposits are found near the little village of Francisco, about 25 miles west of the city of Pinar del Rio on the Western Railroad of Havana. The principal ridges are anticlines, and consist of very thick deposits of sandy shales and slates containing a large number of little veins of white quartz which, by the gradual disintegration of the mass of the material, is left covering the surface. This quartz occasionally shows sulphide, but is generally barren of any such indication. At times lenticular masses of a more or less pure limestone were observed in these slates. The shales, which are of light color, are occasionally talcose. The formation would tentatively be classed as the Lower Cambrian, and the heavy ridges of comparatively horizontal limestone found in the anticlinal valleys as the Upper Cambrian. Along the crest of these slaty ridges deposits of iron-ore are found which are apparently in place, and were probably formed by replacement of masses of limestone similar to those noted elsewhere. The ready disintegration of the slates, and the

Jul 1, 1907

By D. F. Kaufman, E. D. Levine, L. R. Aronin

ThE primary slip plane in hcp metal crystals can usually be inferred from the c/a ratio. Basal slip is the primary system at room temperature for zinc, cadmium, magnesium, cobalt, and rhenium, all of which have a c/a ratio greater than 1.60. Zirconium and titanium, on the other hand, each with a c/a ratio of 1.59, deform primarily by (1010) [ll20] prismatic slip. The increasing tendency toward prismatic slip in these materials is generally thought to be associated with the increase in atomic density on (10i0) as c/a is reduced. Beryllium, with a c/a ratio of 1.57, would, according to the above scheme, be expected to exhibit prismatic slip. However, in beryllium of commercial purity, the primary deformation mode at room temperature is basal slip.' The ratio of critical shear stress for prismatic to that for basal slip at room temperature is approximately 5:l. The critical shear stress for prismatic slip decreases quite rapidly with increasing temperature, however, and at 500°C the ratio is approximately unity. The apparently anomalous behavior of beryllium has led to speculation that prismatic slip in this material may be restricted by an anisotropic effect of impurities,' and that, if beryllium could be purified to a sufficient extent, prismatic slip might predominate at room temperature. In such a case, the conditions under which basal cleavage can occur would be suppressed, and enhanced low-temperature ductility might result. With the advent of the floating-zone method for purification of beryllium,3 it has become possible to determine experimentally the effects of purification on basal and prismatic slip. Tensile tests were performed at room temperature on single crystals oriented favorably either for basal or prismatic slip. The crystals had been purified to various extents by zone-refining, employing procedures that have been described elsewhere.4 Relative purities of the crystals were estimated by measuring the ratio of electrical resistance at 4.2"K to that at 298°K. Typical values ranged from 0.40 for commercial-purity material to 7.7 X 10"4 for crystals prepared from vacuum-distilled beryllium and subjected to six zone-refining passes. The purity dependence of the critical shear stresses for basal and prismatic slip is shown in Fig. 1. In the purity range studied, the critical shear stress for basal slip is decreased from 1.4 to 0.14 kg per sq mm. The critical shear stress for prismatic slip is decreased from 6.7 to 5.3 kg per sq mm. The decreases in critical shear stress for each deformation mode, therefore, are approximately equivalent. No purification anisotropy is observed. Because of the absolute magnitudes of the critical stresses, the ratio of the critical shear stress for prismatic slip to that for basal slip actually increases from 5:l to 38:l at the highest purity level studied. It is evident, therefore, that basal slip is the primary deformation mode in high-purity beryllium. This fact must be accounted for in any rationalization of the deformation behavior of hcp metals. This work was performed at Nuclear Metals, Inc., under the sponsorship of the U.S. Atomic Energy Commission.

Jan 1, 1964

By G. C. Kuczynski

Two particles in mutual contact form a system which is not in thermo-dynamical equilibrium, because its total surface free energy is not a minimum. If such a system is left for a certain period of time, the bonding of the two particles will take place in order to decrease the total surface area, even though the temperature is lower than the melting point. This phenomenon of bonding of two or more particles with the application of heat only and at temperatures below melting point of any component of the system will be called sintering, although the powder metallurgists use this term in a broader sense, including the presence of molten phase and pressure. It is the objective of this paper to study this process and the mechanisms involved in it. This problem is of utmost importance to powder metallurgy and powder ceramics, and its technological aspects have been studied for a good many years. However, the powder metallurgical operations are too complex and include too many superimposing mechanisms, and too many variables for a direct study. It was therefore advisable for the purposes of this study to reduce the variables to a minimum. In this work the radius of the interface formed during bonding in a simple system composed of a spherical particle and a large block of the same metal was studied as a function of time and temperature. It is believed that the mechanism involved in this simple process is fundamental to any sintering operations. Previous Work J. Frenkell was the first to make a serious attempt to develop a theory of sintering. He assumed that the process consists of a slow deformation of crystalline particles under the influence of surface tension which reduces to a viscous flow where the coefficient of viscosity n is related to the self-diffusion coefficient D by the following equation 1 _ D D6kT [1] where 6 is interatomic distance, k the Boltzman constant, and T the absolute temperature. This type of viscous flow of a crystalline substance is essentially different from the ordinary plastic flow. The latter is a specific propcrty of crystals and cannot take place in amorphous bodies. According to Frenkel this viscous type of flow is due to the diffusion of the holes or vacancies arising in the lattice. He was able to derive an equation relating the growth of the interface between two spherical crystalline particles or between a particle and a semi-infinite crystal (Fig 1) to time t at constant temperature. This relationship can be written as follows: x²— 3/2 a/nt [2] where x is the radius of the interface assumed to be circular, a the original radius of the sphere and a surface tension of the material. The other assump- x tions are that x is less than 0.3 and that during the period 1 the original radius, a, of the metallic particle did not change appreciably. A. J. Shaler and J. Wulff2 followed closely the ideas of Frenkel in their theory of sintering of a mass of metallic powder. Neither Frenkel nor Shaler has validated his theoretical speculations with conclusive experimental data. Two measurements reported by

Jan 1, 1950

By Ta M. Li, John D. Wiebmer

Record high prices, burgeoning exploration programs, mine-mill openings, and plant expansions have all characterized a dramatic: resurgence of the US uranium industry in recent years. But while the bull is leading the way on the production side of the nuclear fuel cycle, there is reason for caution from the end-users' viewpoint. How fast will electrical demand grow in the years to come, and what portion of that will nuclear generators supply? How do utilities play their cards when the government holds two of the largest jokers in the deck-a policy on spent fuel reprocessing and a timetable for the fast breeder reactor? Is there a shortfall in domestic uranium supplies on the horizon?

Jan 10, 1978

By M. W. Strong

The technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in formation, the type of problems, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differential pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all materials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improvement of material and its most efficient use has to be carried out. In this paper will be discussed the main mud problems of Iran, some of which are peculiar to local conditions while others are of the general type common to all workers in this subject. Underground Conditions In deep wells in Iran the normal overburden may consist of: (1) up to several thousand feet of marls with interbedded sandstones and limestones of varying porosity and permeability; (2) beneath this a chemical series of rock salt and anhydrites, containing various marls and thin limestones,

Jan 1, 1939

By S. R. Goodman, Hsun Hu

PREVIOUS investigations on the temperature dependence of rolling texture transition in high-purity silver1'2 and in electrolytic copperS have shown that a brass-type texture is favored at low rolling tem- peratures, whereas a copper-type texture is favored at high rolling temperatures. The transition takes place gradually as a function of the temperature of deformation, and a general correlation between texture transition and stacking-fault frequency or probability exists—a copper-type texture is associated with low stacking-fault frequencies, and a brass-type texture is associated with high stacking-fault frequencies. If the stacking-fault energy is calculated from the stacking-fault frequency and the dislocation density of the specimen, one finds that with low stacking-fault energies a brass-type texture will be developed, and that with high stacking-fault energies the texture will be of the copper-type. These findings are consistent with the idea that the formation of rolling textures in fcc metals may depend on their stacking-fault energy, although results of such nature always involve the ambiguity that a change in the density (or width) of stacking faults produced by deformation at different temperatures may be actually due to a variation in the stress, rather than due to a change in the specific stacking-fault energy per se. It has also been shown that the type of annealing texture depends entirely on the deformation texture. From a copper-type rolling texture, a strong cube texture will be formed upon recrystallization, whereas from a brass-type rolling texture, the annealing texture will be quite different from the cube orientation. Based on these results on texture transition in pure fcc metals, it appeared possible to effect a

Jan 1, 1963

By M. W. Strong

The technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in formation, the type of problems, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differential pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all materials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improvement of material and its most efficient use has to be carried out. In this paper will be discussed the main mud problems of Iran, some of which are peculiar to local conditions while others are of the general type common to all workers in this subject. Underground Conditions In deep wells in Iran the normal overburden may consist of: (1) up to several thousand feet of marls with interbedded sandstones and limestones of varying porosity and permeability; (2) beneath this a chemical series of rock salt and anhydrites, containing various marls and thin limestones,

Jan 1, 1939

By G. D. Bengough

CORROSION tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply f oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case f salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion f the metal was shown in some experiments due to Friend .2 He tested the corrosion f mild steel plates immersed in water in glass jars, a steady stream f air being drawn over the surface of the water in the jars. The air passing through half the number f jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor."

Jan 1, 1929

By Edmund Newton

THE steel industry of the United States has depended in the past almost wholly upon imports for its supplies of manganese. Many of the important domestic sources yield ores leaner in their natural condition than the foreign ores the steel industry has been accustomed to use. To make them available, therefore, either' the ores must be concentrated or the practice of the steel industry modified. Roughly 25,000 T. annually of high-grade manganese ores are used for dry batteries, for chemical purposes, and in other ways; while approximately 750,000 T. are required for making steel. By present practice, every ton of steel takes an average of about 14 lb. (1.8 kg.) of metallic manganese. This is generally added to the steel in the form of an alloy, the standard alloys being the 80-per cent. ferro-manganese and the 20-per cent. spiegeleisen. During the year 1917 286,000 T. of ferromanganese and 193,291 T. of spiegeleisen were made in this country, the former largely from imported ores; and 45,381 T.

Jan 2, 1919

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments, and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table 1 are reported the compositions of the core and cladding alloy for the material used for the experiments. [ ] In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion.1-7 Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R301 varies with the gauge, as shown in Table 2, several gauges were investigated. [ ] MATERIAL AND PROCEDURE The material used was sheet of the following gauges: 0.025, 0.040, 0.064, 0.102, 0.170. Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: 910°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After 200 min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1945