Search Documents

By Mark J. Klein, Robert A. Haggins

The pesence of a small amount of oxygen was found to cause significant grain growth restraint in 99.99 pct Ag. This behavior does not seem to be due to the presence of an oxide dispersion, but instead, to be related to the existence of minute amounts of oxygen m solid solution. In the amounts necessary to cause the observed effects it was found that oxygen migrates with extreme rapidity, probably along extended structural imperfections, such as dislocations and grain boundaries. A number of years ago, hastton' observed that the presence of small amounts of oxygen caused a retardation of grain growth in silver. He attributed this behavior to the formation of a fine dispersion of oxide particles by the internal oxidation of trace impurities. More recently, wood2 also found that oxygen caused grain growth restraint in copper. Experiments using both copper and a dilute solution of aluminum in copper led to the conclusion that the effects observed in copper were due to oxygen in solid solution, rather than an oxide dispersion. During the course of a study of the influence of several solutes on the recrystallization of Silver, the presence of minute amounts of oxygen was found to exert a very significant influence on grain growth. The experiments reported here were undertaken to determine whether the grain growth restraint observed in silver due to the presence of oxygen is related to oxygen in solution or to an oxide dispersion. Because of the difficulty in measurement and control of the very small oxygen concentrations causing the observed effects no attempt was made to treat the data in a quantitative manner. EXPERIMENTAL PROCEDURE AND RESULTS Silver of 99.99 pct purity was melted and cast into slabs in a vacuum of better than 0.1 p. These slabs were reduced 50 pct by cold rolling to a thickness of approximately 2.5 mm. Samples cut from this material were annealed in vacuum for a series of different times at 803°C. Another group of samples was similarly annealed in air. This temperature is well above the recrystallization range for silver of this purity (150" to 200°C). The mean grain diameter of these samples was measured, both in the center and near the edge, using the line-intel-cept method, and is shown as a function of annealing time in Fig. 1. The grain size in the centers of the samples annealed in air was found to be larger than that of the surface regions, while the grain growth behavior of the edge and center regions annealed in a vacuum was approximately the same. he edge measurements were taken at a distance of 0.2 mm from the surface.) A few samples were annealed in nitrogen. Their behavior was identical to that of the vacuum-annealed samples. Samples annealed in oxygen had approximately the same grain growth behavior as those annealed in air, leading to the conclusion that this behaviouer is due to oxygen. The microstructure of a sample annealed in air at 803" for. 30 minutes is shown in Fig. 2. The smaller grain size near the surface is characteristic of the iir-annealed specimens. Possible causes of this grain growth restraint in the air-annealed specimen are the formation of an im-

Jan 1, 1962

By G. S. Hume

Petroleum is produced in Canada in the provinces of New Brunswick, Ontario and Alberta and in the Northwest Territories. The total production, however, is relatively small in comparison with the consumption, the value of imports exceeding 40 million dollars a year. Production figures are given in Tables 1 and 2. In Turner Valley, still the largest producing gas and oil field in Canada, five wells were completed during the year. The largest of these

Jan 1, 1936

By G. S. Hume

The total production of crude oil in Canada showed only a small improvement in 1936 over 1935, but developments of great importance took place in Alberta on the west flank of the Turner Valley field in the foothills southwest of Calgary. These have led to renewed activity in drilling such as has not been experienced for many years, and undoubtedly this will result in a very considerable increase in the oil production during 1937.

Jan 1, 1937

By G. S. Hume

Petroleum is produced in Canada in the provinces of New Brunswick, Ontario and Alberta and in the Northwest Territories. The total production, however, is relatively small in comparison with the consumption, the value of imports exceeding 40 million dollars a year. Production figures are given in Tables 1 and 2. In Turner Valley, still the largest producing gas and oil field in Canada, five wells were completed during the year. The largest of these

Jan 1, 1936

By C. L. Colburn

THE statutory requirements of the States and the district rules are, broadly speaking, similar. There is just enough difference to make it tantalizing. DIFFERENCES IN STATE LEGISLATION GOVERNING THE LOCATION OF MINING CLAIMS Discovery Discovery is the first step in the location of the claim. The provision of the Revised Statutes (2320) is, "No location of a mining claim shall be made until the discovery of the vein or lode within the limits of the claim located." Strictly speaking, discovery may be defined as the finding of ore or metalliferous rock in place in a well-defined vein. This definition was too strict, so discovery extended later to cover such indications of the presence of ore, within rock in place, as would justify an experienced miner in spending his time and money with a reasonable expectation of finding ore in paying quantities. According to Colorado statutes a discovery must show a well-defined crevice; in Arizona, a lode, deposit, or mineral in place; in Montana, a well-defined crevice or valuable deposit; in Nevada, a lode or deposit of mineral in place. It is wrong to require a discovery. An honest prospector, wishing to obey the law, finds himself compelled, in most cases, to evade this point. In Clear Creek district, Colorado, a quartz seam will constitute a discovery; in Butte, a red capping; in Leadville or Ely, it is any place where a man can find a piece of vacant ground big enough upon which to sink a 10-ft. hole. If the vein or deposit outcrops a man can show a discovery, but if it does not outcrop it is foolish to compel him to show one; and this point has been gently side-stepped. Any hole 10 ft. deep now constitutes a discovery. It is no use having laws that the people cannot consistently obey. No sane man will dig unless he expects to find mineral, and he should be protected while digging. He should be required to show that he has mineral ground only when he comes to patent.

Jan 6, 1914

By G. St. J. Perrott

ONE of the important hazards in coal mining is the danger of ignition of explosive mixtures of methane and air or coal dust and air, or both, by the explosives used in blasting the coal. It has long been recognized that certain explosives are more dangerous than others in this respect. In America and abroad, government testing stations have been established for officially passing on the suitability of explosives for use in coal mines. In this country the Federal government is given no power to enforce the use of the approved explosives but merely publishes from time to time, through the Bureau of Mines, those explosives which have passed the tests necessary to place them on the list for use in coal mines. In spite of this lack of police power, the increase in the use of permissible explosives since the promulgation of the first list in 1909 has been rapid. In 1912, only 8 per cent. of the explosives used in coal mines were permissible; in 1925, this figure had increased to 25 per cent. While the past record of permissible explosives has been most gratifying, it is very desirable that we pave the way for further improvement in explosives and blasting methods by learning more about the mechanism of ignition of gas and coal dust by explosives. To this end a considerable amount of investigative work already has been carried out and a large amount yet remains to be done. It is the purpose of this paper to discuss briefly the effect of the characteristics of explosives and method of loading in the borehole on the liability of a blown-out shot to ignite explosive mixtures of gas or dust. For an account of the methods by which an explosive is tested for permissibility for use in coal mines, the reader is referred to Schedule 17-A of the U. S. Bureau of Mines.

Jan 10, 1926

By F. A. Jerabek, H. L. Hartman

This study presents results of investigations in a small model of segregation in discharged fill slurry, the quantity of solids escaping in the drain liquid, and the relationship of solids to slurry concentration and discharge rate. Compressibilities of fine fill material, in dry and wet states and individual size fractions, are compared. Two terms are frequently used in describing the hydraulic placement of fill material underground: hydraulic stowing is mostly associated with the underground flushing of coarse-sized fill material, such as coal washery refuse; while hydraulic backfilling refers to placement of small-sized fill material, e.g., sand or classified mill tailings, mainly in metal mines. Characteristically, in backfilling, only a few hours may elapse between the time the material is hoisted as ore and redeposited as fill underground. Hydraulic filling was first used about 100 years ago to control subsidence in coal mines. It was subsequently adopted in many mining operations all over the world, but its basic concepts have never been adequately studied and analyzed. This is not surprising, when one considers the number of variables involved in the hydraulic backfilling operation. Recently, much work has been done on the problems of transportation of slurries in pipes. Comparatively less research work has been done concerning the physical properties of fill material (compressibility, cementation, permeability, etc.). Very little work has been done on the problems of fill placing, distribution, and segregation of fill material discharged in the mine void. It is the purpose of this paper to explore two of the basic, lesser known aspects of filling: segregation and compressibility in discharged fill slurry. Difficulties in observing the behavior of hydraulic fill slurry during the pouring operation underground, and insufficient knowledge to conduct any kind of meaningful theoretical analysis, suggest experimental model studies. The tests described in the following sections were conducted in the Rock Mechanics Laboratory of the Department of Mining at Penn State.

Jan 1, 1965

By Schlumberger, C

IN the search for practical geological problems amenable to solution by the potential methods, the geophysicist is led to study mathematically various theoretical cases. In these idealistic discussions, the media under consideration are generally supposed to be homogeneous and iso-tropic. The geophysicist, of course, realizes perfectly that these condi-tions do not occur in their entirety in reality. However, the assumptions made are justified, because very often they are necessary in order to render possible an exhaustive study of a given problem, which otherwise would be too complicated, and would not lend itself to a complete mathe-matical analysis. Of the above two assumptions, that concerning the homogeneity of a given geological formation is satisfactorily realized except in so far as isotropy is concerned, since this property is not often encountered in practice. As a consequence, it is very desirable for the geophysicist to have quite an extensive knowledge of the properties of anisotropic forma-tions, and of the laws that govern the propagation of electric current therein. With such principles in mind, he will be able to decide whether the conclusions arrived at in simple, isotropic conditions are still correct in more complex cases, or in what way they must be modified or adapted in order to constitute a sound basis for the interpretation of the results obtained in anisotropic media. On the other hand, the fact that in anisotropic formations themobility of the ions is greater along the strike than perpendicular thereto can be utilized for determining the direction of the dip by induc-tion measurements. We therefore propose to study in three successive chapters the following points: 1. Propagation of the electric current in anisotropic media. 2. Some consequences of the anisotropy of geological formations with reference to the surface electrical measurements, and their interpretation. 3. Determination of the direction of the dip of anisotropic formations by surface induction measurements.

Jan 1, 1933

By R. M. Brick, Arthur Phillips

The normal method of preparing metallic alloys for commercial use involves the preparation of a melt containing the given components in the chosen proportions and allowing the homogeneous liquid mass to solidify in a mold of the desired form. The solidification is frequently accompanied by a segregation of the alloying elements in different parts of the casting. When the segregation is occasioned primarily by marked differences in density of the solid and liquid phases, it is termed "gravity" segregation. When the segregation conforms to a selective freezing in harmony with the teachings of the equilibrium diagram of the alloy system—i.e., the lower melting phases are concentrated in the regions of the casting last to freeze—it is often referred to as "normal" segregation. However, in many cases the lower-melting part of the system is concentrated in the parts of the casting first to freeze and the result in this case is termed "inverse" segregation. To complete the terminology of the subject, normal segregation in a single phase is usually called "coring" and the word will be used in that sense in this paper. Inverse segregation, particularly when the liquid phase is exuded or sweated out on the surface of the casting, is sometimes called "liquation." Unfortunately, some ambiguity has arisen from the use of this term and it is perhaps advisable to confine its use to the dictionary definition; namely, "The separation of two phases by heat sufficient to melt one but not the other." The gravity and normal types of segregation are both well understood and to some extent, are controllable by taking advantage of the most favorable cooling rate for a given casting condition. Inverse segregation has received considerable attention from several investigators but none of the theories offered seem to account in a convincing way for the many examples of this type. The observations made in the present work on segregation in single crystals, and in some other castings, tend to support one theory of the mechanism of inverse segregation and definitely to

Jan 1, 1937

By Nev A. Gokcen

PUBLISHED data on the solubility of nitrogen in liquid manganese are widely discordant. Ochsenfeldl observed that a Mn-N alloy with 3.6 pct N consisted of solid and liquid phases at 1260°C but at 13 00° to 1340°C the solid phase disappeared and the liquid contained 0.1 to 0.13 pct N. In contrast Saito's measurements at approxhately 1400°C yielded an average value of 0.97 pct N. Sieverts3 volumetric method is not suitable for the determination of gas solubility in manganese because the liquid metal vaporizes readily and condenses in the cooler parts of the apparatus where it can absorb large amounts of nitrogen. The purpose of this investigation was, therefore, to determine the solubility of nitrogen in manganese accurately in the range of 1273" to 1500°C. The experimental method used in this study was as follows. Electrolytic manganese of 99.9 pct purity, and weighing 50 g, was melted in a pure alumina crucible placed in a tubular furnace. Temperature was measured with a Pt-10 pct Rh thermocouple and controlled within ± 5°C. Pure nitrogen was bubbled through the melt for 1 hr at constant temperature and then a sample was taken by sucking the metal into a 2-mm clear silica tube and immediately quenching in water. The sample was broken into small pieces and found to be sound to the naked eye. The entire sample was then dissolved and the resulting solution was analyzed for nitrogen by the well-known solution-distillation method. The experimental results are presented in Fig. 1. All the nitrogen solubility data refer to 1 atm of nitrogen pressure; hence the observed values are slightly corrected by using Sieverts' equation when the atmospheric pressure differed more than 5 mm Hg from 760 mm, and further, in the case of the runs at 1500°C the correction arising from the presence of Mn vapor has been made. (Cf. Eq. [3]). Scattering in the data is within ±5°C in temperature measurement and ±3 pct in total nitrogen analysis. The straight line in Fig. 1, correlating the percentage of dissolved nitrogen, %N, with the inverse temperature in OK-1, can be expressed by:

Jan 1, 1962

By D. W. Frommer, M. M. Fine

Early in 1957 St. Joseph Lead Co. announced discovery of three new centers of iron ore deposition in east central Missouri.1 The discovery resulted from exploratory drilling in the vicinity of a magnetic anomaly or high. A deep hole, drilled into the Pre-Cambrian porphyry to determine the cause of anomaly, penetrated a magnetite-rich deposit.2 The magnetic surveys that revealed the anomalies were begun by the Missouri Geological Survey in 1929 and were continued into the 1930's 3. At that time an area in Crawford County known as the Bourbon magnetic high was located. A second anomaly, similar in size and intensity, was discovered about six miles to the northeast in Franklin County in the vicinity of Sullivan. This area was not studied in detail until the early 1940's.

Jan 3, 1959

ALTHOUGH the open-hearth charge contributes CO, C02, H2, A and water vapor to the combustion gases and absorbs oxygen from them, in the main the thermal effects in the melting charge and molten bath can be considered independently of those in fuel combustion; the latter then is regarded simply as the source of the net heat required to finish a heat of steel. First of all, it should be remembered that a large percentage of the heat supplied to the bath is furnished by oxidation of the various elements in the charge itself. If this charge consisted of 80 to 100 per cent of hot metal and the oxidation were accomplished by blowing in air or oxygen, as in the bessemer converter, the net heat absorption would be negative; that is, the bath would contribute part of the heat required to keep the melting chamber hot, in addition to that contained in the finished steel and slag. In actual open-hearth practices, probably the nearest approach to this is in the duplex furnace, charged with bessemer-blown metal and some hot metal, where very little heat is required to complete the refining and nearly all the heat energy from fuel combustion is used to keep the roof and walls of the melting chamber up to around 2900 to 3000 F (1600 to 1650 C), so that the bath will not cool off during the refining. The other extreme is with all-cold charges containing around 80 per cent steel scrap and 20 per cent cast iron or cold pig iron, in which case a very large proportion of the heat in the bath at tap is supplied from the fuel combustion. THERMAL EFFECTS IN MELTING In a typical heat, the fuel furnishes about four million British thermal units per ton of steel produced. The heat required, for the metallurgical processes is not easily defined in useful manner but it ranges downward from about one million Btu, depending not only on the charge but on the manner of calculation. In, any event, this requirement appears. small in comparison with the

Jan 1, 1964

By Joseph C. Kieffer

THE Duquesne property of the Callahan Zinc-Lead Co. is about 20 miles east of Nogales, in southern Arizona. One mine is near the mill, but most of the mill feed is hauled in by truck from a number of small mines. The same sulphides are found in all the ores, in general, but the amounts vary considerably. All ores contain silver, copper, lead and zinc minerals but one mine ships ore high in silver and lead and low in copper and zinc; while another mine ships ore high in copper and zinc, and low in silver and lead. The common sulphides are galena, carrying most of the silver; chalcopyrite; sphalerite, carrying iron in solid solution; and pyrite, in a gangue consisting of limestone, quartz and garnet. Mineralization, is fairly coarse. At the present grind of about 66 per cent minus 200 mesh most of the sulphides are liberated. A small amount of chalcopyrite is locked up with the sphalerite and cannot be liberated at an economic grind, and the copper carried into the zinc concentrate with the sphalerite accounts for the comparatively poor recovery of copper in the copper-lead concentrate. PRODUCTION OF TWO CONCENTRATES The milling problem, which was complicated by the extreme variation in the grade of the feed, was first attacked with the idea of producing a silver-copper-lead concentrate and a zinc concentrate, both with satisfactory grades and recoveries. By February 194I, it was felt that these objectives had been attained, when the grades of the various products and the recoveries were as shown in Table I. [ ] A rough outline of the flowsheet and reagents used is as follows: Minus ¾ -in. feed to a 7-ft. by 36-in. Hardinge ball mill working in closed circuit with a 36-in. Wemco classifier. The classifier overflow passes to the second cell of an 8-cell bank of No. I8 Special Denver Sub-A flotation machines (volume, 22.5 cu. ft. per cell). A rougher concentrate is removed from the second to the fifth cells inclusive, and returned to the first cell, which is the cleaner. A scavenger concentrate is removed from the sixth, seventh, and eighth cells, and returned to the third cell. Consump-

Jan 1, 1942

By R. G. Treuting, W. C. Ellis

The twinned state is characterized by a lattice of coincidence sites. Imperfections are required at stable lateral twin interfaces. Twinned regions can occur with relative ease in the diamond cubic IN recent contributions1,2 on the origin and growth of cubic annealing twins, attention has been directed to the orientation relations between such twinned components and their parent matrix. There are some aspects of twinning which may be illuminated by a more detailed consideration of the twinned state" alone. As an extreme example, the dense twinning in cast ingots of germanium,&apos; as contrasted with the rarity of twins in cast face-centered cubic metals, is yet to be accounted for. It has been this that has led us to the present work, which, it will be noted, uses methods and constructions in many respects similar to those of Kronberg and Wilson.&apos; In the cubic systems, a 70" 32&apos; rotation about a <110> axis is angularly equivalent, as to twinning, to the more usually considered 180" rotation about a <111> axis. Figs. 1 and 2 show a (110) projection of a twinned face-centered cubic lattice and a twinned diamond cubic lattice. In both figures, the two adjacent planes A and B, shown by the larger and smaller circles, are sufficient to represent the entire array. In each case a section of lattice, the original atom sites of which are shown by open circles, has been rotated as indicated through 70" 32&apos; to bring an original. [112] direction into coincidence with the [112] diiection. The latter is the intercept on the (110) projection of the (ill) plane normal thereto, the twinning plane. In the face-centered cubic case the rotation can be performed about an axis passing through an atom-site; the mirror plane then is also a composition plane containing atoms common to both twinned and untwinned lattices. The diamond cubic lattice may be construed as two interpenetrated face-centered lattices. Its (111) planes recur in a sequence of alternately short and long interspacings. Consequently a mirror plane for twinning cannot be a composition plane, but must be the bisector of one of the spacings. When the longer spacing is selected, the closest distance of approach across the mirror plane in the [ill] direc- tion is identical with that in the untwinned structure. In each case periodically recurring (ill) planes (parallel with the twinning plane) are found, on which there is coincidence of atom sites of the pre-twinned and twinned orientations; these are indicated by the cross-hatched circles. In the face-centered lattice there is such coincidence every third (ill) plane; in the diamond cubic lattice, on two adjacent planes in every six. At the twinning interface in the latter, there is on each side of the mirror plane a (ill) plane of atoms common to both twin components. Conceivably, there is little influence on a plane of atoms about to be adhered to such a pair of coincidence planes, whether it be laid down in a normal or in a twinned position with respect to the previously formed structure. Slawson% as attributed the high incidence of twinning in diamond to this boundary state. Further examination shows that the motion of intermediate planes can consist of various pairs of equal and opposite translations, for example of (ill) planes in the [l&apos;;i2) direction, the familiar twinning shear, indicated in the small schematics in the figures. Since the translations form a system of shears of alternating sign between coincidence planes, twinning could take place by such a mechanism over an extended region without extensive shear; in fact, in this case any atom moves but the distance in the [1i2] direction. One alternative construction for the face-centered cubic lattice leading to the same end result is illustrated in Fig. 3. The plane (711) with respect to the pretwinning orientation (the twinning plane of Fig. 1) is given, the twinned region arbitrarily bounded by <110> and <112> directions. The coupled shear is identical to that of Fig. 1. The "rotational" movement about coincidence sites generating the same twinned position could consist as shown of the translation a,/d% for each atom of a group of three in the B layer in a different one of the three <112> directions, and a similar translation of the underlying three atoms in the C layer in either the same or the opposite sense. This is not dissimilar to Kronberg and Wilson&apos;s construction for their 22" rotation of three adjacent (111) planes.

Jan 1, 1952

By L. N. Cosner, C. F. Austin, J. K. Pringle

Shock wave attenuation studies with three igneous rocks are reported: a spessartite elastic to low intensity stress waves, a diorite which is anelastic, and a porous scoria. The level of shock passing through a given thickness of rock has been determined by donor-receptor methods using high speed streak cameras. Test results include shock propagation velocities adjacent to the explosive, the dependence of test results upon test geometry, and the variation in shock wave attenuation in these three common igneous rock fabrics. The utilization of explosives in rock mediums involves a series of interrelated phenomena. These are the detonation process within the explosive, the transfer of energy from the explosion products to the surrounding rock medium in the form of sound or shock waves, and the transmission of the resulting waves through the rock medium to create damage in the rock mass. The subject of this paper is the investigation of the close-in phenomena that occur in the intensely shocked rock immediately adjacent to a detonating explosive charge. The specific aspects studied include propagation velocities, free surface velocities, pulse attenuations and the determination of the equations of state for the test rocks employed. In addition, a series of tests was conducted to indicate the dependence of the test results on the charge diameter utilized. The equations of state for rock materials have been investigated by a number of authors. Lombard, &apos;,&apos; Grine and Fowles,3,4 Zharkov, 5 Hughes and McQueen,6 Chabai,7,8 and Bass9 have published equation of state data on rock materials similar in structure or composition to those investigated in the study. Rinehart10 has prepared a voluminous tabulation of the available equation of state data from these publications and in addition has included data on many other rock and earth materials in his compilation. The reader is referred to the extensive tabulations and bibliography of Rinehart for classical studies involving the equations of state of metals and other solids and liquids. The problems of sympathetic detonation between drill holes in hard rock environments has received the attention of various authors as have the problems of explosive rock coupling close-in stress wave attenuation and explosive diameter effects. 11 to 18 In particular, the don or-receptor geometry of this report is very similar to the geometry of adjacent drill holes in rock. Most published pulse velocity and attenuation work in rock has been devoted to velocities at much lower amplitudes than those associated with close-in explosives phenomena and most attenuation studies involve transmission and attenuation across large spans of material. Excellent work in these areas has been published by the U. S. Bureau of Mines and by many individuals and groups engaged in geophysical research. SELECTION OF TEST MATERIALS A series of rock materials was desired for this test program that would be meaningful industrially, and that would also yield comparative results from a research viewpoint. Based on the availability of a series of related petro-fabrics, for which there is an abundance of physical and shock response data, three igneous rocks were selected as the test series. The applicability of shock wave studies in igneous rocks to industrial problems is readily demonstrated. Hardrock tunneling, quarrying and mining take place in igneous rocks throughout the world. From a research point of view, igneous rocks exhibit a wide variety of grain sizes and considerable diversity in composition, yet the common igneous rocks have a general similarity in their constituent mineral structures and in their grain-to-grain bonding mechanisms. The latter is based on the concept of rock formation through magma cooling and crystallization, though the degree of liquefaction in granitic plutonic masses is indeed a moot question. Three specific types of igneous rock were chosen for study. A coarse-grained granitic textured rock was desired that would serve as a representative of the widely abundant intrusive rocks of the world and

Jan 1, 1967

By B. F. Decker, D. Harker

The recrystallization reaction in OFHC and spectroscopically pure copper has been followed by X ray diffraction determinations of the amount of material with the cold-worked and recrystallized textures in specimens which had been given various heat treatments. The heats of activation for recrystallization are found to be: 29.9 kcal per rnol for OFHC copper and 22.4 kcal per rnol for spectroscopic copper. A reliable and speedy method for measuring the amount of recrystallized material in a piece of rolled metal, together with a new scheme for low temperature heat treatment, have made possible a determination of the activation energy for recrystallization in rolled copper. This method for studying recrystallization rates is different from others reported in the literature.&apos; Oxygen free, high conductivity copper—OFHC copper—of purity 99.98 pct gave an activation energy for recrystallization of 29.9 kcal per mol with recrystallization data taken in the temperature range 208-245°C. Copper of purity 99.999 pct from the American Smelting & Refining Co. gave an activation energy for recrystallization of 22.4 kcal per mol with recrystallization data taken in the temperature range 43-135°C. The great change in activation energy for recrystallization as the small amount of impurity in the metal is decreased suggests that the motion of grain boundaries is conditioned by the impurities which must be concentrated in them. Thus the OFHC copper recrystallizes with an activation energy of the order of magnitude to be expected for the diffusion of the kind of impurities likely to be present. The high purity copper, on the other hand, recrystallizes with a much lower activation energy, in accord with the notion that the grain boundaries need not wait for the impurities to diffuse with them. Copper when strongly cold-rolled has a well-defined crystallite texture which can be described by saying that the [111] direction of the face- centered cubic crystals is aligned approximately in the cross-rolling direction and that faces of the form {110} lie approximately in the rolling plane. When such rolled copper is completely annealed the crystallite texture is quite different: the [loo] direction is in the cross-rolling direction and faces of the form (100) are in the rolling plane. At intermediate stages of annealing, the copper contains both textures. If a Geiger counter X ray diffraction spectrometer is set up so as to measure the intensity of the (200) Bragg reflection from the rolled surface of a piece of copper strip, this intensity increases from a very small value in the cold-worked state to a maximum as the specimen is annealed. The same would be true for (200) reflections from planes normal to the rolling or cross-rolling directions. In view of this fact, the amount of material in the copper which has recrystallized can be measured by comparing the intensities of one of these reflections just mentioned with the intensity from a similar specimen after complete annealing. In much the same way the intensity of (111) reflections from planes normal to the cross-rolling direction could be used to measure the amount of unrecrystallized material in the specimen. In the work to be described here the amounts of recrystallized and unrecrystallized material in partly annealed rolled copper specimens were determined in this way. Experimental Procedure Samples of oxygen free high conductivity (OFHC) copper, cold-rolled 99.7 pct to 0.002 in. thickness, were subjected to heat treatments for various chosen times at four different temperatures, and high purity copper samples, cold-rolled 98.0 pct to 0.0015 in. thickness, at six different temperatures. Each sample, after treatment, was placed in an orientation sample holder for use with a Geiger counter X ray spectrometer and a reading was taken of the intensity of the (200) reflection from planes perpendicular to

Jan 1, 1951

By F. Paredes, W. R. Holman, R. W. Crawford

The diffusion coefficient for hydrogen in the ß titanium alloy containing 13 pct V, 11 pct CY, and 3 pct A1 was measured over the temperature range 20° to 500°C. Results fit the expression: D= 1.58 x lgs exp-------==-----) cm2,sec THE diffusion coefficient for hydrogen in the metastable ß-phase titanium alloy containing 13 pct V, 11 pct Cr, and 3 pct A1 was measured as part of an investigation of the effects of hydrogen on the mechanical properties of titanium alloys. Several theories on the mechanisms of hydrogen embrittle-ment include diffusion of hydrogen at ambient temperature as an important step in the embrittling process.&apos;-5 In hydrogen-contaminated a-ß titanium alloys, it has been postulated that the rate-controlling step may be the rate at which hydrogen diffuses from the ß phase to stress- or strain-nucleated brittle hydride platelets at the a-ß interface.&apos; However, embrittlement of the all-ß alloy investigated in this work may proceed by a different mechanism, since this alloy can be embrittled without the formation of detectable hydride platelets.6 Troiano has suggested that in this case the mechanism of delayed failure or embrittlement is similar to that proposed for high-strength steel, i.e., repeated crack initiation caused by a decrease in bonding energy as hydrogen diffuses to points of high tri-axial stress at the root of a notch. In both types of alloy the rate of embrittlement is believed to be controlled by diffusion of hydrogen in the ß phase. Accurate hydrogen-diffusion data in the vicinity of room temperature should therefore be of some assistance in understanding the mechanisms of embrittlement in these two classes of titanium alloys. Diffusion of hydrogen in pure titanium has been studied by Wasilewski and Kehl7 at temperatures above 500°C. Their measurements on diffusion in the ß phase were extended below the ß-a transformation temperature (882°C) to approximately 600°C. This was possible because of the 8 stabilizing effect of hydrogen. No results at lower temperatures have been published and there are no data in the literature on hydrogen diffusion in the ß -phase alloy used in this program. Hydrogen diffusion in metals is generally investigated by measuring the rate of transport of hydrogen past a solid-gas interface, i.e., by absorption, permeation, or degassing-rate measurements. These methods produce accurate diffusion data when bulk diffusion is the rate-determining step in the over-all process. However, at the lower temperatures of interest in hydrogen-embrittlement studies or under conditions where surface films are present, the measured rates may be surface-controlled and the calculated diffusion coefficients will be in error. Surface effects were eliminated in the present work by using a modification of the common welded-couple technique m which two bars with uniform but different compositions are joined before the diffusion anneal." The same type of step change in the initial concentration vs distance curve was produced by electrolytically hydrogenating thin-strip specimens which had been electrically insulated over half of their length. Concentration vs distance curves were determined, after appropriate diffusion-annealing treatments, by vacuum-extraction analyses of transverse samples sheared from the strips. Diffusion coefficients were calculated by the methods of Grube.M This technique was feasible because of the large concentrations of hydrogen which can be charged into p -phase alloys without the formation of hydrides15&apos;16 and because of the extremely low degassing rates observed when hydrogenated titanium alloys are heated in air. EXPERIMENTAL WORK The diffusion couples were cut from a 0.022-in.-thick mi ll-annealed sheet.* Strips 8 in. long by 1/2

Jan 1, 1965

By Herbert M. Wilson

We of the employer class represent labor in the social organization and in industry just as truly as do those who labor only with their hands, and, because our labor is chiefly with our brains, the duty is all the more imposed upon us to use those gifts in which we excel in helping steer a clear course through the turbulent waters in which we are now enmeshed. Only their selfish engrossment in the daily tasks they were employed to perform could possibly have permitted the great majority of the intelligent and industrious German people to become terrorized by a handful of the idle, the vicious, and the criminal, whom the elections to the National Assembly showed to be in as pitiful a minority as they are in Russia, in this, and in other countries. It is the leisure unemployment of the I.W.W.&apos;s, the Bolsheviki, and the Sparticans that has enabled them to devote their whole time to a concerted and aggressive struggle against the great majority of those of the world&apos;s workers who are unorganized, and who are therefore even in opposition one to the other. In union there is strength, and this was never better illustrated than by these conditions. The great fallacy of our previous attitude toward social and industrial problems has been the belief that labor, by which we commonly mean organized or physical labor, is something antagonistic to and having a different object in life from that great body of unorganized laborers who work with their brains. Our difficulty has been our lack of will or opportunity to think. The hurry of our daily struggle to earn our livelihood under the nerve-racking pressure of modern civilization has left us no opportunity for quiet thought and study. The physical laborer, and above all the laborer in the mines, on the other hand, has all his hours of toil in which to think over, in all their varied aspects, those problems that concern his immediate, personal well-being. As a result he has arrived at perhaps a more true appreciation of the facts of life in their relation to social and industrial conditions than we. Have we not too readily adopted the view that, as the managers of industry under the direction of capital, it has been our duty to think and act in opposition to labor, rather than to realize that we also are laborers, have like aspirations, and should participate in a free and aggressive solution of these problems rather than leave their solution

Jan 1, 1919

By Rodney P. Smith

The diffusivity of carbon (0.1 wt pct C) in Fe-Nz alloys (0 to 100 pct Ni) has been determined for the temperature range 860° to 1100°C. As a function of nickel content, the diffusivity has a maximum near 60 pct Ni (the maximum diffusivity being about 1.3 times that in the absence of nickel); the activation energy has a maximum between 40 and 50 pct Ni and a maximum between 80 and 90 pct Ni. The difference between the minimum activation energy and that in iron is about 3000 cal pev g-atom; Do has a minimum between 40 and 50 pct Ni and a maximum between 80 and 90 pct Ni. The results cannot be rationalized by an approximate thermodynamic treatment. THE diffusivity of carbon has been determined in a number of iron alloys over a limited concentration range. It seemed desirable to investigate a system which allows an extended range of alloy composition within a single-phase region. The Fe-Ni system is ideal in this respect, in that all alloys from 100 pct Fe to 100 pct Ni are fee in a convenient temperature range.&apos; The carbon diffusivity was determined by a decar-burization method. The experimental procedure was identical with that used to determine the diffusivity of carbon in y Fe-Co alloys.2 The experimental data are given in Table I. A small correction (order of a few percent) has been made to the measured carbon loss to correct for the carbon lost from the ends of the cylinders.&apos; Since the diffusivity of carbon varies with carbon content the measured diffusivity is an average value for a carbon content between zero (surface) and that at the center of the sample at the end of the decarburization periods. In making the correction in D to 0.1 wt pct C it is assumed that the measured D corresponds to the arithmetical mean of the carbon content at the surface and at the center of the sample at the end of the decarburization period.3 Since this correction is small (<4 pct in D) and since for our decarburization times the changes in carbon content at the center of the sample was small the mean carbon content could have been taken as half the initial value. It is further assumed that the change in D with carbon content for the alloys is the same as that for the diffusion of carbon in iron. From the data of Wells, Batz, and Mehl4 and of smith5 the correction of D from the mean carbon content to 0.1 wt pct C is 0.3 (0.1 - mean wt pct C). The results for iron are given in Ref. 2. Within the experimental error log Do.l%C for each alloy is a linear function of 1/T; the constants for the equation determined by the method of least squares are given in Table I. The deviations of the experimental points from the least-squares line are of the order of 2 pct in D. A comparison of our results for the diffusivity of carbon in nickel with those of other investigations is shown in Fig. 1. The lower curve in Fig. 1 is a linear extrapolation of values calculated* from the equation of Diamond6 for the relaxation time (temperature range 100° to 500°C). The results indicate a small increase in the activation energy over the temperature range 100° to 1400°C; however, it is difficult to say whether the change in Q is real or experimental error. Certainly the change in Q is less than the variation of 5 kcal per g-atom in the diffusivity of carbon in a iron.6 The experimental data for all the alloys are plotted in Fig. 2. As a function of nickel content the diffusivity has a maximum near 60 wt pct Ni at all temperatures investigated and possibly a minimum between 80 and 90 wt pct Ni for temperatures below 1000°C. The activation energy, Q, and log Do are plotted as a function of the nickel content in Fig. 3. Due to the limited temperature range of our experiments neither Q nor Do can be determined precisely; the activation energies appear to be consistent to ±0.3 kcal per g-atom; however the deviation from the absolute values may be considerably larger, see Table II. The Do values probably have little significance. The solid line for Do in Fig. 3 represents the values required to reproduce the experimental values for D when Q has values represented by the upper solid line The diffusivity of carbon may be expressed in terms of the mobility B22, the activity coefficient r2,

Jan 1, 1967

By D. S. Greig

There was a decline in the Italian oil production in 1933 and also in the footage drilled. A total of about 194,500 bbl. of crude oil was produced in the Emilia district of northern Italy from the same fields in production as in 1932. New drilling to the extent of 80,700 ft. failed to find new production to compensate for the decline in old wells, and no new fields were discovered in spite of an active exploration campaign by the government-owned company A.G.I.P., which has just completed the first year of a five-year exploration program. This company drilled a total of about 33,000 ft. The majority of its tests were drilled in the Po Valley upon locations selected by geophysical methods. This company is changing over to the rotary system for all future wells. It produced about 16,600 bbl. of oil from wells near Salsomaggiore and in the Po Valley. The Petroli d&apos;Italia, which operates the old fields of Montechino, Valleja and Gratera south of Piacenza, has been doing normal development drilling in the endeavor to extend its present fields. Also it was drilling two exploration wells in the Torino district. It drilled a total of about 13,930 ft. and produced approximately 12,645 bbl. of very high-grade oil (specific gravity about 0.765). The Societa Petrolifera Italiana was occupied chiefly in exploratory drilling in the endeavor to extend its producing fields at Salsomaggiore and at Vallezza, south of Parma. It was also drilling one exploration well at Rile dell7Olio near Voghera on the line Milan-Genoa. It drilled a total of 33,849 ft. and obtained a production from its two fields of 165,273 bbl. It also produced 123,220 gal. of casinghead gasoline from Vallezza field absorption plant.

Jan 1, 1934