Search Documents

By C. W. Spencer, R. A. Rummel, F. N. Rhines

SPECIMENS of five cast Cu-Bi alloys, containing 4.68, 0.53, 0.043, 0.0064, and 0.0025 wt pct Bi and cast pure copper were subjected to a bend test to determine their relative ductility. Using metallo-graphlc methods the structures of the fractured surfaces were compared with those of the polished cross sections. Embrittlement was found to be associated with the presence of a second phase in the grain boundaries although, in the lower bismuth

Jan 1, 1958

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, all of the following rock types occur; oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently, overblasting wasted drilling time, and explosives caused excessive throw.

Jan 4, 1974

By W. H. McCormick, H. J. Benecki

CONSIDERING that a typical modern drilling machine strikes approximately 2000 blows per min and may develop a force of 30 to 200 ft-lb, de- pending upon size of the drill used, the importance of uniform stress distribution in this type of drilling becomes obvious. If the rod were perfectly symmetrical, and if it did not rotate, the problem would be relatively simple, however, the necessary forging, machining and heat treating operations prevent attaining this state of perfection. Take the modern hollow drill rod. The blow is transmitted not from the striking end of the rod directly through to the point of impact of the bit in the rock, but rather through a somewhat complex tool. To add further problems, this entire assembly is rotated immediately after the impacting blow. Rather than attempt to discuss the magnitude and distribution of stresses, it is desired to present a few things that will minimize unusual stress concentration and produce a rod in which the stress distribution will approach the theoretical ideal.

Jan 3, 1954

By Fred DeVaney

THE coercimeter, as its name implies, is an instrument for measuring the coercive force? of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are inter-esting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or, elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. The turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determina-tion of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1938

By Alexander Bowie

Of the following problems, some have been suggested by recent articles in technical journals, which have led me to believe that the mathematical discussion here submitted may be of use to mining engineers. Problem I. To Find the Grade or Angle of Inclination upon which the Power Required to Move a Loaded Car Down-hill Will Haul an Empty One Up-hill. Let a be the desired angle of inclination; C, the coefficient of' friction; W and w, the weight in pounds of the loaded and of the empty car, respectively.

Jan 1, 1902

By J. W. Bolton

PRODUCTION of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical.

Jan 1, 1929

By AIME AIME

THE two illustrations below, furnished through the courtesy of J. P. Messervey, Deputy Inspector of Mines, Department of Public Works and Mines, Province of Nova Scotia, show a fourth-level stope in the salt mine at Malagash, N. S. Fig. I was taken when the stope was begun, and Fig. 2 shows how it looked two months later, the photographs being taken from the came point. This stope is at a depth of about 300 ft. and is on the MacKay seam, which is the central band of white salt running through the Malagarh deposit. As run be seen. the vein is vertical. and varies from a foot to 50 ft. in thickness. The

Jan 1, 1932

By George Haworth

ELECTRICAL illumination of shafts, stations, and haulageways has been successfully practiced for many years, but its use in drifts and stopes where mining operations are carried on has- been limited. The large underground drifts of the Tri-State field present a lighting problem that is not satisfactorily solved by the use of the carbide lamp. It has, for some time, been the policy of the Anna Beaver mine to provide ample lighting throughout the underground haulage drifts and working faces. This has, in the

Jan 6, 1928

H. M. BOYLSTON, Cambridge, Mass.-I would first like to ask what machine Capt. Bellis used to make his tests on impact strength. I have made some tests with the Charpy impact machine, the specimen being supported at both ends and nicked in the middle, and, find that the results do not always agree with those obtained by the Izod and other machines. I would also like to ask what effect the composition and heat treatment of the tool steel had on the drilling of his rifle barrels, as compared, with the heat treatment of the steel itself? I notice that the analysis of the composition of steel used shows sulphur 0.050 and phosphorus 0.065; I should like to ask how those high limits of sulphur and phosphorus came to be allowed? I have some data which lead me to feel pretty certain that those high limits make for very unsafe steel in rifle barrels. It has never been explained to the satisfaction of all of us, why the manganese is so high: 1.22 per cent. I believe several reasons have been stated; among them, that it is high in order to compensate for the high sulphur, and also to increase the elastic limit and improve other physical properties of steel. Lastly, I wish to ask whether Capt. Bellis has tried any different methods of heat-treating his steel rifle barrels? Apparently these were all heat-treated before machining; has he had any experience with heat-treatment after machining, especially after drilling? Those questions may seem somewhat outside of the range of this -paper, but they are important, and if Captain Bellis can give us any information, it will be very helpful. Dr. J. A. MATHEWS,* Syracuse, N. Y.-The same subject was discussed here last year, and the earlier papers by Dr. Carle Hayward seem to indicate that nothing was gained by the length of time of 'tempering. (It should be borne in mind that his results were based upon electrical and magnetic measurements and not upon tensile tests.) That idea has been accepted as gospel by steel workers, until late years, and particu-larly in connection with alloy steels, on which there is no question that the effect of time of tempering is very marked.

Jan 4, 1918

By A. J. Weinig

The method described is a modification of Schutzenberger's whereby the solution in titrations and the standards are protected from the atmosphere by a layer of kerosene. Indigo-disulfonate is the indicator and sodium hydrosulfite the standard. The method is rapid and delicate. It has been tried on a variety of mill solutions and mill men have found the method of value. THE important part that dissolved oxygen plays in the cyanide treat-ment of gold and silver ores is commonly recognized by most metallurgists and mill men.. But heretofore there has been no simple method on which the mill man could rely for determining the amount of oxygen in the various mill solutions. A few methods are adaptable to the, laboratory, such as the gasometric1 determination by actually measuring the oxygen. Winkler's2 iodometric method, and Schutzenberger's3 method, which depends on the reducing action of sodium hyposulfite on a blue solution of indigo carmine; but these are not readily adaptable to the needs of the mill man and cannot be applied to cyanide solutions without modification. The gasometric method is the most accurate but it takes too long to complete a determination. White's' method (a colorimetric method that depends on the degree of coloration imparted to a solution of pyrogallic acid in the presence of caustic soda) although much more rapid than any of the methods named, often gives misleading results on account of grading of colors of different solutions, which nearly always contain various kinds of salts. The method herein described was devised for the use of the mill man, the aim being to develop a simple, practical, accurate method. It is a modification of the Schutzenberger method and depends on the reducing

Jan 8, 1924

By Clarence Wright

THE average lead and zinc content of the ores mined and milled in the Joplin district is low as compared with that of other lead and zinc deposits throughout the United States. Because of this fact and of the high grade of the concentrates, the ratio of concentration is unusually high. Most of the operating companies have aimed to produce as high a grade of concentrate as possible in order to obtain the highest price for their product. They have done this at the sacrifice of the percentage of zinc recovered. The average percentage of zinc recovery is from 60 to 70 per cent. For percentage of recoveries from actual mill tests, see tables. The concentration is commonly effected by crushing the ore to h-in. (12.7 mm.) size and subjecting it to a roughing and cleaning over two or more large Cooley jigs, of the Harz type, the finer sands being treated on the usual types of sand and slime tables. The treatment of slimes by flotation is being tested at several of the larger mills. COARSE CONCENTRATION When the ore. has been hoisted from the mine it is dumped onto a chute leading to a grizzly made of iron bars, usually heavy rails, spaced 4 to -5 in. (101 to 127 mm.) apart. The oversize is caught on the grizzly, the mineralized pieces are broken with sledge hammers so as to pass through, and the boulders that are practically barren are sorted out by hand and trammed to the waste-rock pile. The proportion of waste rock thus sorted out varies from a fraction of 1 per cent to 15 per cent., depending on the nature of the rock.

Jan 10, 1917

By Robert S. Schecter, Paul M. Bommer

This paper presents the development of and results from a computer model of in situ uranium leaching. This model uses a streamline-concentration balance approach and is useful with a wide range of reservoirs. It can be used with any type of well system, in a reservoir with or without boundaries, and with any form of descriptive kinetics. The model also includes the effects of dispersion and consumption of oxidant by minerals other than uranium. The effects of areal sweep, variable uranium concentrations, variable permeability, and the presence of oxidant consumers on uranium production are shown and discussed.

Jan 1, 1979

By Alan K. Burton

An industry-wide demand for bigger and more efficient trucks, with their supposed economies of scale, is well established. Some trucks have been, and often are brought "off the shelf," with the manufacturer offering only certain minor options, much as in the private automobile industry. The market is well established; there is keen competition; in recent years there have been few significant changes, and few are expected. With large trucks (100-ton-capacity and over), however, the situation is different. Here, with an individual truck costing several hundred thousand dollars, there is an ever in- creasing trend to engineer a truck for a specific application. The body will be designed and sized for the material that the truck will carry; the engine and transmission will be geared to the haul profile, and tires will be designed to suit road conditions and work requirements. Early Truck Development Haulage trucks designed expressly for open-pit mine service were introduced during the 1930's. The first models to arrive on the scene hauled about 15 tons, and easily outperformed the modified highway trucks that had been used for mine haulage up to that time.

Jan 8, 1975

By Eckley B. Coxe

IN making surveys in the anthracite coal regions of Pennsylvania, the ordinary engineer's chain (50 or 100 feet long) is generally used, both above and below ground. Sometimes, where it is difficult to chain, as, for instance, across a chasm, a wire is stretched from one station to the other, the distance is marked on the wire and its length is then measured with the ordinary chain. Having had occasion lately to make some surveys where it was necessary to determine with great accuracy the position of the land or property line, not

Jan 1, 1874

By Zay Jeffries

EACH generation accepts the developments of the preceding generations without full appreciation of the difficulties that had to be overcome or of the effect of any given development on society. Today, the production of pig iron is the yardstick with which general industrial health and progress are measured. So natural and logical does this seem to us, that it is difficult to picture conditions prior to the fourteenth century when pig iron was unknown. Not only was pig iron unknown but iron or steel could not be melted and poured into castings; all iron and steel articles were forged from sponge iron. All castings, as well as many worked articles, were made of non-ferrous metals or alloys. In many parts of the world, over long periods of time, not only was the annual exchange value of non-ferrous metals greater than that of iron and steel, but their combined tonnage was greater. At present, the value of the pig iron produced in a year is of the same order of magnitude as that of all non-ferrous metals combined; the tonnage of pig iron is, however, about twenty times that of all non-ferrous metals combined. Owing to lack of records, we will probably never know the relative importance of the various metals at all periods in historic times. A certain conclusion is that the iron and steel industry, since the discovery of pig iron and the cheap methods of converting it into steel, has grown at a much more rapid rate than the non-ferrous metal industries. Notwith-standing their fundamental fitness for man's needs, iron and steel owe their importance in no small degree to the low cost of production. The low cost was a result of increased knowledge of the production appliances and of the metallurgical processes. This increased knowledge is the key to our modern industrial civilization.

Jan 5, 1924

By William B. Plank

ENGINEERING educators and industries are worried about the engineering manpower shortage that is predicted as a result of the increasing demand for trained engineers not only by industry but by the armed services. This is in the face of a decreasing supply, as is shown by this and other studies. Not only has the number of entering freshmen been decreasing since 1947, because of a decrease in the number of high school graduates entering engineering, but the total number of high school graduates will continue to decrease until 1958 because of the lowered birth rate during the depression years.

Jan 8, 1951

By N. B. Aughenbaugh, W. C. Patrick

The availability of a thorough, simple-to-use roof fall classification system is desirable for several reasons. First, such a system would expedite the reporting of falls for the purposes of estimating material removal costs, analyzing damage levels, and complying with federal regulations to report falls in certain areas of the mine. Second, the classification system would allow the mining engineer to record falls routinely with little time and effort expended. This would encourage him to make observations concerning what type of roof support would work best in a given situation. Third, and probably most important, an

Jan 3, 1979

THE ladle is a small hearth made on a cage of iron bars like a bird-cage, and has a handle so that it can easily be taken from the forge and carried wherever desired. It is a common device and is much used among masters for small castings, but with a large weight you would have difficulty in lifting it by hand even though you were aided by levers and winches. If you should indeed do it, it would be just as if you had lifted the aforesaid hearth by force, and this would be unwise if you could do anything less difficult. A forge is likewise made for this, with a good pair of large bellows that are well covered with cloth. When the small hearth has been made with good clay, baked, and well covered with ashes, it is placed in front of the mouth [of the bellows] and a crown of two or three brick ends is built around it on top of the rim so that the charcoal may be held better and in greater quantity. Then, having lit the fire and heated the ladle and the charcoal, the pieces of material that you wish to melt are gradually put on

Jan 1, 1942

By Gary Mack, Donald E. Scheck

To help management keep key machines or processes at peak efficiency, draglines, shovels and blast hole drills have been equipped with micro- processor based monitors. The dragline and shovel monitors log operating data such as energy consumption, bucket position, cab rotation and the clock time of key elements within each cycle as well as maintenance information. The output consists of maintenance and management data such as the number of cycles, average cycle times, swing angles, depths and downtimes. Extensive experimentation has shown that a blast hole monitor can provide a log of each blast hole in which the hard to fragment zones are indicated. The logs are printed on board the drill and serve as the design basis for decked loading of the holes. As a result, the fragmentation of the overburden has improved markedly with the same or less powder consumption. This material is based upon work supported in part by the Bureau of Mines, Department of the Interior under Grant Numbers G1115006, G1115391 and G5 105006. Any opinions, findings, and conclusions or recommendations expressed in this publication are those of the authors and do not necessarily reflect the views of the Bureau of Mines, Department of the Interior.

Jan 1, 1983

By W. A. Hooker

This portion of Mexico is quite beyond the ordinary routes .of travel, and is seldom visited. Its mines have not the record of enormous wealth which has recently attracted foreign capital to other parts of the republic; but for many centuries it has been a mining country, and at some periods evidently a productive one. In 1881 the writer visited the State and spent some time in the inspection of the mines. The absence of published information regarding its mining industry is his apology for presenting to the Institute these notes on the subject. Oaxaca is, with one exception (Chiapas), the most southerly of the Mexican States. It extends from latitude 18o 20' to 15' 45' N.— about 180 miles, by some 300 miles, in an east and west direction, and embraces a large part of the Isthmus of Tehuantepec. The coast-line is wholly on the Pacific. The State has an area of 27,470 square miles, nearly that of the State of Maine, and a population estimated at one million, or thirty-six to the square mile. The great continental Cordillera which farther north and west expands into broad table-lands, is here converged into narrower limits and occupies the greater portion of the country; the main

Jan 1, 1887