Search Documents

By L. L. Swift

AT the present time there are four base metals being used for automo-tive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows in some types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and pre-venting overheating and rapid wear of parts. Less plasticity is required in a bearing metal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coeffi-cient of friction. Under most operating conditions the friction depends on the unit pressure of the bearing, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the bearing.1 The hardness of the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measure-ment of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual constituents was developed to fill this need.

Jan 1, 1938

By G. R. Heckman, H. J. Murphy, C. T. Sims

An incestigation has been made of the effects of heat treatment and alloy composition on the long-time stress-rupture properties and structural stability of the similar nickel-base alloys Udimet-500, Lrdimet-520, and Udimet-700. Rupture test data are presented at stresses ranging from 4 to 50 ksi at temperatures from 1450° to 1900°F for times up to 14,000 hr. Ductility response is emphasized. Optical and electron tnicroscopy were complemented by X-ray diffraction analyses of extracted phases to relate microstructural stability to the observed rupture properties. Particular attention is paid to Udimet-520 since structural characteristics of this alloy appear to vary somewhat from its sister alloys. Both cast and wrought performance of Lrdimet-500 are discussed. The computerized PHACOMP calculational technique, based on electron-vacuncy theory, is discussed and related to structural stability where appropriate. Electron microscopy and microprobe techniques were used to conduct evaluation of the oxidation characteristics of Udimet-500 exposed in air for 16,100 hr. The steady advance in strength and reliability of nickel-base superalloys continues to be one of the high points of modern metallurgy. The stress capability of these materials has increased steadily, allowing higher and higher operating temperatures in the highly sophisticated aircraft and industrial gas turbines now on the market. The attendant increase in efficiency, of course, means greatly improved power output. Gas turbines for industrial and marine use have long been designed with these objectives paramount the usual design requirements in terms of time of service being 100,000 hr. High-efficiency, long-life aircraft such as the supersonic transport require superalloy engine materials with high-strength and long-time structural stability. Thus, materials studied for and operating experience from industrial gas turbines provide a good reservoir from which technology of high value to the SST program can be drawn. This study is one such case. Three prominent nickel-base super alloys—Udimet 500, Udimet 520, and Udimet 700 were extensively evaluated for industrial gas turbine bucket use. Particular attention was directed toward structural stability as a requisite property. Within the present context, structural stability is defined as freedom from the propensity to form strength-robbing or embrittling phases such as u,p,x,or Laves, and the ability to maintain useful rupture strength and ductility throughout design life. MATERIALS The three alloys, cast Udimet 500 (U-500C), Udimet 520, and Udimet 700, were chosen for detailed evaluation based on preliminary studies which indicated that U-500C and U-520 possessed comparable rupture strength capabilities, and that U -700 had a greater strength capability but somewhat poorer ductility than wrought U-500. The nominal compositions of the three alloys, along with the compositions of the heats investigated, are presented in Table I. PROCEDURE Dimensionally rejected U-520 buckets from Special Metals Corp. heat 63370 were heat-treated using the four cycles delineated in Table 11. Cycle A was investigated to determine the effects of a shortened 1700°F primary age. Cycle B was considered a "standard" treatment. Cycle C investigated a higher solution temperature in combination with a shortened primary age, while cycle D assessed the effect of the higher solution temperature alone. These heat treatments were designed to produce optimum combinations of rupture strength and ductility through maximum y' development, the development of a y' grain boundary cushion, promotion of MC carbide degeneration reactions, and agglomeration of resultant M23CB. Since one of the premises of the evaluation of U-520 was that rupture strength would be equivalent to U-500, forged U-500 buckets from Special Metals Corp. heat 62916 were heat-treated with cycles A, B, and C to provide comparison. The heat-treated structures of U-520 and U-500 are illustrated in the 8700 times electron micrographs of Fig. l. The U-700 tested was all from 3-in.-diam hot-rolled and centerless-ground rod from Special Metals Corp. heat 2-1426. Two heat-treatment cycles were employed, E and F of Table 11. Cycle E is a standard four-step, triple-age treatment intended to provide an optimum match of strength and ductility through well-developed matrix and grain boundary y', as recommended by U-700 vendors. Treatment F is a shortened , single-age cycle which could provide a significant processing cost reduction should adequate strength and ductility be maintained. Following heat treatment, rupture specimens of U-500 and U-520 were machined from the buckets and tested. Standard rupture bars of U -700 were machined from the heat-treated rod and rupture-tested. Failed and withdrawn rupture bars were prepared and examined by optical and electron microscopy. Select specimens were electrolytically digested, and the residues analyzed for carbide and topologically close-packed phases using CrKa or CoKo radiation. Of the six different U-500C heats evaluated, five were cast by Misco Precision Casting Co. and one was cast by Haynes Stellite Co. Cast-to-size rupture bars

Jan 1, 1968

By Frederick Laist

ABOUT six years ago the Anaconda Copper Mining Co. decided to investigate the possibility of extracting zinc from the ores of certain mines in the Butte district. These ores are of a complex character and contain so much iron and lead that the concentrate contains only 33 to 35 per cent. zinc. Investigations showed that while a high-grade concentrate could not be obtained by ordinary methods, such as tabling and magnetic treatment, a fair grade could be made by the Horwood process. In this method, the concentrate resulting from the flotation of all of the sulfides is given a light roast and this calcine is subjected to flotation in the presence of a large amount of sulfuric acid; the resulting concentrate contains most of the zinc and a residue contains most of the iron. The fact that the lead, copper, and silver are divided approximately equally between the zinc concentrate and the iron residue and the large consumption of acid, which ranged from 50 to 100 lb. (22 to 45 kg.) per ton of concentrates, were serious objections to this plan. The zinc recovery, moreover, was low, as a considerable percentage invariably accompanied the iron. While a profit might be made on the ores by the use of this process, it was thought that other and more promising methods might be devised. After carefully studying the field and doing some laboratory work on various processes that had been suggested, it was decided that the electrolysis of sulfate solutions was the most promising. We soon found, as have other investigators, that the only way to obtain a good zinc deposit is to have the electrolyte free from all metals more electro-negative than zinc, such as copper, cadmium, lead, arsenic, antimony, etc. Arsenic and antimony are particularly injurious, causing very poor current efficiency and small yield per horsepower when present in amounts so small as almost to defy detection-1 mg. or less per liter.

Jan 10, 1920

By C. A. Heiland

For a long time it has been known that it is possible to deduce conclusions about the physical constitution of the interior of the earth from the records of natural earthquakes obtained by stationary seismographs. In view of this fact it is surprising how late, relatively speaking, geologic prospecting by seismic methods has been taken up, although the first suggestion was made 40 years ago—that travel-time curves of artificial explosions might be used for the study of the change of the velocity of seismic waves as depth. Further suggestions of practical applications of artificial explosions for geologic purposes were made by Belar12 by von dem Borne,3 by Benndorf and by Galitzin,5 but it was not .until 1919 that Mintrop obtained a patent on the seismic prospecting method which he has applied commercially on a large scale ever since. Dr. Mintrop came to this country with his method at about 1923. Since that time, several American oil companies have developed seismographs of the mechanical type for the vertical component similar to that of Mintrop's (Humble Oil Co., Dr. Ricker). Other consulting geophysical companies designed other types of seismic devices, the simplest of them for the recording of the first impulse being the geophone (McCol-lum Geophone Co.). The galvanometric recording method as first proposed by Galitzin is being used (Geophysical Research Corpn.?) and use is being made even of the piezoelectric properties of crystals for portable seismographs (F. Rieber). There is such an enormous variety of all kinds of portable seismographs, vibrographs, accelerographs, etc., that it is difficult to decide just what kind is preferable. Unfortunately, nothing has been published as yet about American designs of portable seismographs, except the Wood-Anderson torsion-seismometer. After Mintrop's design of portable seismographs, other constructions were made

Jan 1, 1929

By Walter Lawson

THE first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not, been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economi-cally prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established.

Jan 1, 1938

By J. Volney Lewis

The following paper is based chiefly on work done for the North Carolina Geological Survey, and is presented here by permission of Professor J. A. Holmes, State Geologist. It represents, in a very general way, the field-results obtained during the summer months of 1893, and 1894, and part of 1895; and the portions pertaining to North Carolina are, to a certain extent, abstracts of a report shortly to be published as Bulletin No. 11 of the State Survey. Less emphasis, however, is here laid on the petrographic descriptions of the peridotites, and more detailed treatment is given to subjects pertaining to methods of mining, cleaning, and utilization of the commercial product, corundum. Some of the most extensive fields for investigation which this subject presents have been scarcely more than suggested.

Jan 1, 1896

Jan 1, 1907

By Bruno V. Nordberg

The high cost of coal in Butte and the development of large amounts of cheap electric power from the Missouri river caused the Anaconda Copper Mining Co. in 1908 to make an investigation as to the possibility of adapt- ing this cheap electric power for the operation of their many large hoisting plants. At this time electric power had already been adopted for practically all other power purposes around the mines, such as pumping, compressing air, etc. The map (Fig. 1) shows the location of the mines of the Butte mining district. These mines are located within a circle of approximately a 1-mile

Jan 1, 1914

By AIME AIME

MOST of us are far .from home, and yet our Japanese hosts- have made us feel very much at home. Here in the Orient we engineers are .learning a new meaning for the word "orientation"- hereafter that engineering term will be a synonym for gracious hospitality, and "to orient" will mean to turn a whole country over to the World Engineering Congress. Mere geographic distance is no longer able to separate nations, for the conquest of distance is one of the triumphs of 'modern engineering. We of the Americas are fortunate in the position of our continents: with their shores lapped by the waves of two oceans, we face' two great civilizations, the' Occidental and the Oriental, and thus we can share the intellectual resources of these two older cultures.

Jan 1, 1929

By Arthur Taggart

THIS paper describes the result of a series of experiments run in the laboratory of the School of Mines, Columbia University, during the winter of 1927-28. It shows that the several operating adjustments of a pneumatic table produce effects in the action of a, given coal that may be grouped into two classes, viz.: stroke length, speed and rocker-arm angle, which affect longitudinal travel; air supply and table slope (transverse and longitudinal), which determine transverse travel. The magnitude of the effect of the different adjustments varies. Some of the adjustments affect stratification of the bed, both as respects size and specific gravity of the bed components, as well as direction of travel. Operation of a pneumatic table is fundamentally different from that of a wet table in that the former exerts, through the air supplied, a force on the particles upward away from the deck which is lacking on the wet table while, on the other hand, it lacks the positive control over cross travel that is supplied by the wash and feed water.

Jan 1, 1929

By J. G. Hadley

IN THE early stages of the depression the Utah Copper Co. realized that an unemployment problem would he created which demanded an intelligent and sympathetic solution. The company recognized that as many men as possible must be kept at work on a basis which would ultimately permit of the most efficient reabsorption of displaced labor. The company therefore determined to distribute available work among the greatest number of men and to that end adopted a system of rotating employees on a part-time basis. An employer requires a certain number of days' or shifts' work during the month. Obviously one employee working thirty days or shifts a month is equal to two employees each working fifteen. In principle, therefore, where two employees equally fitted to do certain work are available the work could be divided between them on an equitable basis and twice as many persons would benefit. A rotation plan on this basis was adopted by the Utah Copper, Co. on Jan. 30, 1930. Some variations of the orig¬inal plan have been made from time to time, the reasons for which will be discussed.

Jan 1, 1932

Jan 1, 1969

By R. Schempp

DURING the past few years, general interest in the steel-producing and steel-consuming industries has been centered on the so-called "inherent characteristics" of steels. While often vaguely described, these char-acteristics are known to influence the response to heat-treatment and the hardening characteristics of the material. Although most of the recent papers and discussions have associated the "inherent characteristics" with the austenitic grain size and empha-sized the importance of it, comparatively little is known of the variables that may affect the size of the austenite grain. The work to be described in this paper was carried out during the course of a study on the inherent characteristics of tool steel containing one per cent cart on. The discrepancies encountered in the determination and classification of the austenitic grain size led to in investigation of some of the variants influencing the austenitic grain size as determined by standard methods.

Jan 1, 1937

By Edgar C. Bain

Jan 1, 1932

By Herbert Clark Hoover, Lou Henry Hoover

SINCE I have written of the varied work of pre- paring the ores, I will now write of the various methods of smelting them. Although those who bum, roast and calcinea the ore, take from it something which is mixed or combined with the metals ; and those who crush it with stamps take away much ; and those who wash, screen and sort it, take away still more; yet they cannot remove all which conceals the metal from the eye and renders it crude and unformed. Wherefore smelting is necessary, for by this means earths, solidified juices, and stones are separated from the metals so that they obtain their proper colour and become pure, and may be of great use to mankind in many ways. When the ore is smelted, those things which were mixed with the metal before it was melted are driven forth, because the metal is perfected by fire in this manner. Since metalliferous ores differ greatly amongst themselves, first as to the metals which they contain, then as to the quantity of the metal which is in them, and then by the fact that some are rapidly melted by fire and others slowly, there are, therefore, many methods of smelting. Constant practice has taught the

Jan 1, 1950

By F. G. Cottrell

AS previously announced, Van. H. Manning has resigned as director of the Bureau of Mines, effective June 1, to become director of research with the newly organized American Petroleum Institute. Doctor Manning has been connected with the Department of the Interior for 34 years, having been civil engineer with the Geological Survey, from 1885 to 1910, previous to his connection with the Bureau of Mines which was organized in the latter year. Doctor Manning was appointed to an administrative position in the new Bureau under Joseph A. Holmes, its first director, and on Jan. 1, 1911, was made assistant director. On Jan. 1, 1914, when Doctor Holmes had to relinquish active

Jan 1, 1920

By M. N., Short

TIE Pioneer mining district, better known as the Superior district, from its principal town, is located in Pinal County in south-central Arizona about 80 miles east of Phoenix and 22 miles west of Miami. The region embraces a confused series of mountain ranges of moderate FIG. I.----SUPERIOR, LOOKING NORTH FROM SOUTH BANK OF QUEEN CREEK. MAGMA MINE IS INDICATED BY WASTE DUMP IN GULCH TO RIGHT OF CENTER. height but precipitous slopes, between which lie irregular valleys filled with alluvial detritus. The average elevation is about 2800 ft. in the valleys and the summits of the ranges reach 2000 ft. above this. Superior is situated on the north bank of Queen Creek where it emerges from one of those ranges into a more or less basin-shaped valley. The drainage of Queen Creek is to the southwest and the flood waters spread out and lose themselves in the desert northeast of Florence, the county seat of Pinal County.

Jan 2, 1926

By Ivor Jenkins

Processes employing 'controlled at-mospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been asso-ciated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and dificult prob-lems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases. Controlled atmospheres such as disso-ciated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,' but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1948

By Ivor Jenkins

Processes employing 'controlled at-mospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been asso-ciated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and dificult prob-lems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases. Controlled atmospheres such as disso-ciated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,' but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1948

By Enrique Touceda

The question as to the proper amount of total carbon that the malleable founder would prefer to have in pig iron for use in the production of air-furnace, white iron castings, must be considered from different angles, that is, whether it is desirable or advantageous from an economic standpoint to use some kind of low-carbon scrap on his mixture, or make use of pig and sprue only. Whereas silicon is the acknowledged scrap carrier in the case of cupola gray iron castings, carbon performs this role for the most part in malleable iron practice, irrespective of the character of furnace used for the production of the white iron castings. In this particular, the advantage lies with the maker of gray iron castings in that the silicon content in pig iron through a regulation of furnace temperature is under very easy control by the blast-furnace manager, whereas he has little or no control over the resultant percentage of carbon, as this is dependent on the quantity of coke in the hearth, and hearth temperature, coupled with the amount of hearth slag and its particular composition. As perhaps more than 95 per cent. of white iron castings are made in air furnaces the following statements are intended to cover that situation particularly: In the malleable process the composition of the hard iron castings (that is determined upon as best suited for the work in hand) is the one factor that must control the composition of the mixture to be used; because if the elements are not between certain definite limits individually and collectively the annealed or finished product will be unsoitable, due, perhaps, to lack of sufficient strength or because it is too hard, to machine easily. The annealed product can be divided into two classes, one of which greatly predominates, that is, by far the largest tonnage is used for machine parts where high strength and ductility are essential requisites, while a far smaller amount, light in weight and thin in section, is used for other manufactured products in which castings of any reasonable degree of strength and ductility have proved satisfactory.

Jan 1, 1927