Search Documents

By D. J. Carney, E. C. Rudolphy

IT has been demonstrated that inclusion size, distribution, and composition affect the machin-ability of resulphurized steels. Merchant and Zlatinl concluded that large sulphide inclusions aided machining by forming a (lubricating) coating on the tool face. Boulger et al.² and Van Vlack³ noted that the size, distribution, and composition of the inclusions in the steel affected the machinability. Steel specimens containing large globular sulphide inclusions usually exhibited excellent cutting properties, while machinability was adversely affected by the presence of numbers of oxide-type inclusions. Consequently a thorough knowledge of all the factors which affect the inclusions in the final product is desirable. Since almost all the inclusions have their origin in liquid steel, it was necessary to begin a study of inclusions in free-machining steels by studying the inclusions and chemical segregation in the as-cast ingot. Very little information is available on the size, distribution, shape, and composition of inclusions in large, capped, free-machining steel ingots, particularly the B1113 grade. Gregory and Whiteley4 made a general study of the inclusions in a small, high sulphur, free-machining steel ingot. Also, numerous authors have described the solidification and segregation characteristics of the four basic types of steel ingots, namely, rimmed, capped,7 semikilled,7,8 and killed7,9,10 ingots. Most of these studies were made with plain carbon or low alloy, low sulphur steel. It was desirable to study not only the ingot but also the change in size, shape, and number of inclusions on rolling an ingot to a bloom and thence to a billet. This procedure was followed and it is hoped that this study may serve the dual purpose of adding to the general knowledge of ingot solidification as well as contributing to the knowledge of the size, shape, distribution, and composition of inclusions from the ingot to the billet in a high sulphur, free-machining steel. Procedure A 12.000-lb 23x35x75 in. slab ingot of the B1113 grade was cast, sectioned, and studied both macro-scopically and microscopically. An adjacent ingot from the same heat and of the same size was rolled to a 77/8x77/8 in. bloom and thence to a 21/2x21/2 in. billet. These various bloom and billet sections were also sectioned and studied macroscopically and microscopically. Sectioning the Ingot: The ingot herein described was obtained from the United States Steel Corp.'s South Works Bessemer Blow No. 0193, a B1113 mechanically capped heat. The 23x35 in. ingot (No. 2) was teemed according to normal procedures and after stripping and transportation to the rolling mill was not placed in the soaking pit but allowed to air cool in an upright position. When completely solidified, the ingot was cut into sections by means of a powder scarfing torch and further sectioned by saw cutting as indicated in Fig. 1. Cut No. 2 (1x10x12 in.) from sections A through H was cleaned thoroughly, macroetched in a solution of 50-50 water and hot muriatic acid and used to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 23-in. ingot dimension. Cuts No. 5 and 3 (lx81/2xl0 in. each) from sections A through H were treated in a similar manner to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 35-in. ingot dimension. The composite macrograph of these horizontal ingot sections, which shows a vertical section of the ingot from top to bottom, is shown in Fig. 2. It should be noted that sections No. 2 are normal to sections 5 and 3 in the composite. Drillings for chemical analyses were obtained from selected positions within the above-mentioned ingot sections as noted in Fig. 3. The oxygen content was determined by the vacuum-fusion method. Samples for microscopic examination were cut from

Jan 1, 1954

By Emil Gathmann

Through wide experience at numerous mills in the United States I have found that there is a decided difference of opinion among the producers of steel as to what constitutes commercially sound steel. Some metallurgists insist upon having, for certain grades of steel, a so-called "open steel," i.e., one which contains numerous blowholes of varying sizes, and consequently but little volume of true pipe, although a central intermittent shrinkage cavity often extends well down into the ingot. Such blowholes and pipe are expected to weld up during rolling or forging, because their surfaces are not oxidized. Even if this be admitted, included slag particles and a high degree of segregation are bound to be present in the product of such ingots. Blowholes are the result of an oxidized heat, and all heats, unless made or finished in the electric furnace, are oxidized more or less. Subsequent deoxidation, or rather degasification, either in the ladle or in the mold, or in both, is necessary to reduce or prevent blowholes. As is well known, a greater yield of billets or sheets is secured from the ingot by allowing the formation of blowholes, but this is undoubtedly obtained at the expense of the quality of the product. Decided segregation of carbon, phosphorus, and sulphur, as well as small included slag particles, undoubtedly exists throughout the greater portion of all so-called open steel, and cannot be removed by cropping. The first requisite for sound, homogeneous steel ingots and blooms is therefore, in my opinion, so to treat the steel in the furnace, ladle, and mold that "piping" steel is produced. The line of demarcation between harmful and so-called "harmless" blowholes is practically impossible to define. Is it not, therefore, the better and safer practice to use means for the elimination of blowholes and correspondingly reduce the segregation and allow the formation of a well-defined shrinkage cavity or pipe at the upper end of the ingot? With the relatively cheap deoxidizers available at the present time, e.g., ferro-silicon, aluminum and titanium, there is no commercial reason why all steel should not be thoroughly degasified. A degasified steel being provided, the method of freezing or solidifying the liquid steel into an ingot, and the subsequent working into blooms and thence into various products, is of great importance in reducing the crop or scrap portion of the steel, due to segregation and pipe. How to ac-

Jan 1, 1916

By Edward A. Capillon

The problem of scrap is probably of greater importance in the pro duction of gold, silver and other precious metal alloys than is the case for base metals and alloys. Remelting of gold and silver scrap in the shop is always a costly process because it involves losses by oxidation of thc base metals in the alloy with a consequent increase in the percentage of precious metal. This is most marked in the case of alloys containing the low-boiling and easily oxidized metals zinc and cadmium. Since it is not generally feasible to assay every shop remelt it follows that the possibilities of lost values arc large. So-called rolled gold and silver plate is made by soldering or welding the precious metal alloys onto base metal. Such plate when defective must be sent to the refinery to recover the gold and silver values, thereby involving additional expense in the form of refining charges. It is obvious therefore that gold and silver alloy scrap is an important item in manufacturing cost and must be reduced to a minimum. The amount of scrap resulting from poor metal will depend on a number of factors in the manufacturing operations, not least among which is the melting and casting practice. The notes which follow are a summary of experiments performed at various times to determine what variables in melting and casting are influential in the production of sound alloys. Metals Used in Alloying Pure gold, that is, gold of 24-kt. value is very much too soft for jewelry purposes and it is therefore always alloyed with other metals to increase its hardness and resistance to wear. For the same reason pure silver is seldom used alone but is alloyed with copper, the standard alloy being sterling silver which contains 92.5 per cent. silver and 7.5 per cent. copper. The metals commonly used for alloying gold are silver, coppcr, nickel and zinc. In addition to hardening the gold and producing alloys of different karat values the use of these metals makes possible the production of gold alloys of various colors such as yellow, red, green and white. The gold-silver-copper alloys vary in color from light greenish-white through green, yellow and red depending on the relative amounts of the three metals. Green or yellowish-green colored golds

Jan 1, 1930

CHARLES SCHUCHERT,* New Haven, Conn. (written discussion?).- I embrace ace the opportunity to take part in a discussion of Mr. Woodruff's paper because a successful discerning of what actually constitutes pet-roliferous areas from the geologists' standpoint is worthy of our endeavors, not only from the intellectual side, but also because it may lead, as Mr. Woodruff hopes, to the more certain establishment of principles that can be applied to other continents in exploiting them for petroleum. This discussion will also embrace the results of two other recent papers, one by Alexander W. McCoy and one by Maurice G. Mehl.1 Sources of Petroleum.-Mr. Woodruff is agreed that petroleum comes from plants and animals, or possibly from both, and that it has ac-cumulated by migration into reservoir rocks. These reservoir rocks must of course be porous to become catch basins for the oil and gas, and then, too, their present structures are variable, as they occur in anticlines, domes, terraces, etc. , The structures, he states, are more widespread than are the oil pools, and the same is true for the reservoir rocks. Accordingly, there must be many good sands and structures

Jan 11, 1919

By F. L. Robertson, C. H. Bacon, J. W. Till

A description is given of the development of a process for making low sulphur steel on furnaces fired with 2 1/2 pet sulphur oil. Slag and metal are analyzed at melt. Slag weight is estimated. A simple method for calculating necessary lime additions for making 0.025 and 0.035 pct sulphur steel is given. DURING the last 15 years John Summers & Sons have been confronted increasingly by the problem of producing a low sulphur steel from high sulphur materials. The principles adopted, the processes used, the data collected on a furnace specially set aside to study this problem, and speculation on future developments are dealt with in this paper. This study is limited to two melting shops which make sheet steel only, of the following analysis: C, 0.06 pct; Mn, 0.33; S, 0.04, 0.035, 0.03, and 0.025; and P, 0.02 and 0.015. All the processes described have reference to the manufacturing of this steel and are not necessarily applicable, without modification, to other steels. The raw materials used are given in Table I. Development of Process About 1934, Schenck's work on phosphorus was applied to frame quantitative rules for the removal of phosphorus, with great success. We could however, neither in our own work nor in the voluminous literature, find any assistance to frame quantitative furnace rules to remove sulphur. Perhaps, we should have persevered with Schenck's outstanding chapter on sulphur in The Physical Chemistry of Steelmaking, but we missed the importance of one (Ss) sentence on p. 478. "Evidently this ratio -------- is [S] the important quantity to be considered from the point of view of chemical reaction; it is clear that the sulphur content of the steel alone, as frequently given in the literature cannot suffice for judging the success of the reaction unless special details are given regarding the sulphur charge and the amount of slag."' We were not however very successful in getting values for Schenck's "n" that agreed with (S) arrived at by our direct analysis. [S] In addition to Schenck's work much attention was given to V value. The formula selected for V was: (SCaO) — 1.57 (2 P2O5) (S SiO2) After plotting many charges a curve was obtained, based upon the relationship between the percentage sulphur in the finished steel and V value, Fig. 1. For a long time this was used as standard with about a 60 to 70 pct success on producer-gas fired furnaces, if all uprising scrap was used and no bought scrap used. An inspection of this curve shows clearly that it is not a quantitative manufacturing process, and that it was not sure enough to go to the trouble and expense of doing stage analysis for P,O,,

Jan 1, 1952

By J. J. Casey, R. S. Busk, D. L. Leman

The mechanical properties and the phase-temperature relationships of magnesium-lithium-aluminum, magnesium-lithium-zinc, and magnesium-lithium-aluminum-zinc alloys are presented. It is shown that the strengths of some of these alloys can be tripled by heat treating and aging but that the high strength is accompanied by brittleness and lack of stability. MAGNESIUM-LITHIUM alloys are interesting because the hexagonal structure of magnesium can be changed into the more ductile and workable body-centered cubic structure by the addition of only 10 pct lithium.1 After Loonam2 determined that the ductility of the magnesium-lithium alloys is destroyed by even trace quantities of sodium, it was possible to prepare ductile alioys and study their mechanical properties. Jackson3 and coworkers have ably described their results with both the binary and polynary magnesium-lithium alloys. The present paper is a report of the mechanical properties of wrought magnesium-lithium-aluminurn, magnesium-lithium-zinc, and magnesium-lithium-aluminum-zinc alloys. Experimental Procedure The alloys were made by melting 7 lb of magnesium in a steel crucible under a molten flux of 75 pct LiCl + 25 pct LiF3 previously dried at 1600°F. The metal was heated to 1300°F for alloying aluminum and zinc and then cooled to 1250°F for adding lithium (sodium content: 0.01 to 0.04 pct). After the lithium had been alloyed, dry LiF powder was sprinkled on the melt to thicken the excess flux. After a 15 min holding period, the flux was skimmed off. Paraffin vapors were used to protect the metal as it was poured into 3 in. diam by 11 in. long magnesium molds. Billets were extruded into 3/8-in. diam rod and 1/16 x 3/4-in. strip; sheet was prepared from 1/8x 7/8-in. extruded strip, first by hot rolling and then by cold rolling 2 pct per pass. Hot rollability, or the temperature range through which the alloys could be rolled, was determined by rolling the strip two passes at 30 pct reduction per pass. Cold rollability, or the percentage of cold reduction to cause detrimental cracking, was determined on 0.064-in. hot-rolled sheet. Standard ASTM procedures were followed to obtain the mechanical properties, using 0.2 pct offset for the yield strengths. The level of properties produced with commercial magnesium alloys using the procedure described is given in a previous publication." Results Magnesium - Lithium - Aluminum System: The good workability of magnesium-lithium alloys is illustrated by the data in table I, which shows approximately how the extrusion pressure decreases as the amount of cubic phase increases. Binary magnesium-lithium alloys are soft and weak, but aluminum raises their strengths con-

Jan 1, 1951

By Reynold Q. Shotts

The small domestic underfeed stoker as now designed is unusually sensitive to the coking and plastic properties of coals, and when the attempt is made to burn the high rank coking and caking coals of the Appalachian fields, serious trouble may occur. Part of the trouble may be caused by the ash content and clinkering characteristics of the particular coal in use, but more often it is the result of an excessive ac-in of coke in the form of ''trees,, or masses in the fuel bed. Often the zone of burning becomes so restricted that the fire goes out, and in extreme cases the fire may be lifted completely out of the fuel bed and away from the air ports. Even if the fire is preserved, excessive coking may cause response to subsequent heat demand to be slow and irregular. Coke trees seem to grow most readily during periods of hold-fire operation, so that in order to preserve the fire in mild weather it is often necessary to set the timer for such a long operating period each hour that much unneeded and unwanted heat is developed, causing discomfort. During demand periods the fire may pick up so slowly that the intense burning which develops just before stoker cut-off causes a serious overshooting of the thermostat. Stoker coal performance tests which have been made in a number of labora- tories1,2,3,4,5 are one method of approach to the problem Of selecting stoker coals- As yet these tests have not been standardized and they are expensive and time-consuming. The value of the results probably increases with the length of the test. Sherman and co-workers at Battelle Memorial Institute believe that even a one-week test is not too reliable a trial2 and it is quite likely that Others will agree. A great advantage of such tests is that characteristics of coals, other than the tendency to form coke masses, may be evaluated from them. The selection of stoker coals would be greatly facilitated if there existed some simp1e measure Of the tendency Of a a to form coke in a fuel bed. Although possessing all Of the disadvantages Of any small-scale laboratory test, the test for the free-swelling index of coal has been found useful for evaluating the probable effects Of swelling properties upon combustion.7 Ostborg, Limbacherand Sherman, have shown that the test can Predict, roughly, the tendency Of coke to accumulate in the fuel bed Of a domestic stoker. They also gave instances of its value in predicting combustion behavior in some large installations. The use of the test for free-swelling index has become well established and has been adopted as a standard by the American Society for Testing Materials.8 When domestic stoker coal investigations began at the State Mine Experiment Station in the summer of 1944, it was decided

Jan 1, 1949

By H. M. Roberts

H. M. ROBERTS, Minneapolis, Minn. (communication to the Secretary*). -The rifling of drill cores is a frequent source of interest to men engaged in diamond drilling. Previous to the appearance of Dr. Crane's paper, there has been little record of connected observation or rigid speculation as applied to the cause of rifling. Replying to one of Dr. Crane's letters of inquiry, I ventured my opinion that the cause of rifling was a complex problem in physics, which I had not attempted to solve up to that time, except to ascribe it to the general cause of rotation and vibration of the rods. The question is worth attention not only as a matter of curious scientific interest but also for the reason that it stimulates thought on

Jan 10, 1916

By M. Herman, G. J. London

A series of dilute Fe-Co alloy specimens were prepared from zone-melted iron. The iron used was given ten floating-zone passes in purified hydrogen. Alloying was accomplished by plating a gradient of metallic cobalt onto a 1/4-in.-diam bar of material from a pure plating bath. The deposit was radioac-tively tagged by a small addition of co80 to the plating bath. Alloy homogenization was accomplished by passing an additional floating-zone pass through the plated section of the bar. The final concentration gradient achieved was from residual to about 1000 ppm (0.1 pct) added Co. After homogenization, the bar was swaged to 0.057 in. wire and cut to tensile specimen blanks 1-1/16 in. long. Each specimen was counted in a well-type scintillation counter. The concentration of cobalt was computed by combining the normalized specimen counting rate with the known weight (measured to the nearest 0.01 mg) of cobalt added during plating. Fig. 1 shows the cobalt gradient obtained, exclusive of residual cobalt which was estimated by neutron-activation analysis to be approximately 50 ppm. Results of recrystallization for 1 hr at 750°, 700°, 650°, and 600°C with specimens containing 40, 170, 470, and 870 ppm added Co are shown in Figs. 2, 3, 4, and 5. Recrystallization was accomplished in a dynamic vacuum of less than 1 x 10 torr. The specimens were mounted and polished parallel to the swaging direction. The recrystallization re- sults show a radical coarsening of structure with increasing cobalt concentration. The coarsest structure obtained was at the 470-ppm level (at all recrystallization temperatures) with a slight grain refinement at the 870-ppm level shown. A more normal solid-solution effect is seen in Fig. 5 (60OoC, 1 hr) where the only specimen completely recrystallized is the one containing 47 ppm Co. Since the possibility existed that some atmosphere-contamination phenomenon might be responsible for the observed results the recrystallization series was repeated using sealed quartz capsules. These were filled with purified argon which was gettered during heat treatment on metallic titanium included in the capsules. The results obtained were essentially the same as shown. Another identical alloy was made using a 5-mm-diam bar of Westinghouse Puron. Specimen preparation and recrystallization treatment were also as described. The results obtained (see Table I) were somewhat erratic. Some coarsening in structure does appear at the highest cobalt concentrations. There is no apparent relationship between the coarse, columnar, directionally solidified structure of the as-melted bars and any of the recrystallized grain structures observed, all of which are much finer than the former structure. A recrystallization process can be most simply described as one of homogeneous nucleation of recrystallized grains in a cold-worked matrix followed by more or less uniform growth of the strain free grain into the cold-worked material.' An impurity element may influence one or both of these processes. Aust and utter' have shown that impurities strongly influence grain boundary mobility in lead. Moreover, definite recrystallization textures are produced by small concentrations of tin,3 while additions of silver or gold4 produce large boundary in-

Jan 1, 1964

By Cyril Stanley Smith

METALLURGISTS - or at least metals - have been of central importance in most of the inventions that have shaped the course of man's history. From the first Bronze Age tools to the iron armor of the Roman soldier, the cannon, cast type for printing, the steam engine, the electric motor and modern electronic devices, technological progress has revolved around some particular property or comb nation of properties selected from the metallurgist's repertory. The recent utilization of the energy of the atomic nucleus (currently for military purposes alone but with great constructive implications for the future) is no exception to this, although the use of uranium and plutonium in metallic form is of secondary importance, since the significant properties are those of the nucleus and not of the electrons responsible for metallic behavior. THE METALLURGIST AND ATOMIC ENERGY The metallurgist has a role of central importance to play in the future development of atomic energy. Not only must he make and shape the fissionable materials themselves, but he must also develop auxiliary materials to withstand the extreme conditions imposed on nuclear reactor components by the high heat-transfer rates needed for efficient utilization of the fuel and by the perplexing but interesting effects of radiation on the structure and properties of materials. It is doubtful if there is currently any other field potentially more rewarding to a young metallurgist. Quite apart from the all important but relatively short-range considerations of national security is the vision of the effect on civiliza-

Jan 1, 1953

By G. Sachs, E. J. Riping

All ferrous alloys can be made brittle by straining at sufficiently low temperatures. However, the changes in mechanical properties for different ferrous materials with decreasing testing temperature do not appear to follow any universal law. In particular, complex effects of testing temperature have been observed if cold worked steels were subjected to tensile tests at low temperatures. EFFECTS OF PRESTRAINING AT A TEMPERATURE ABOVE THE TESTING TEMPERATURE ON THE FRACTURE CHARACTERISTICS‡ A considerable amount of data has been presented by a number of investigators on the fracture characteristics of various cold worked steels.' These data usually relate to a two-step procedure first used by Davidenkov,² consisting of stretching by tension to a certain strain or " prestraining" at room temperature and then completing the tensile test, or "testing" at the temperature of liquid air. On the basis of data of this type made available to date, ferrous alloys can be classified into two groups with respect to their fracture characteristics observed on testing at a low temperature after prestraining at room temperature. Very complex phenomena have been observed for all annealed steels. On the other hand, some observations indicate that steels in certain other conditions represent a fundamentally simpler relation. In considering the effect of prestraining at one temperature on the properties obtained at some lower temperature, it should be expected that any cold work reduces the ductility retained in proportion to the magnitude of the cold work. However, the test data presented to date indicate that only heat treated (quenched and tempered) steels appear to conform to this expectation, according to the very limited test data in Fig 1, presented by McAdam, Geil and Mebs. This series of tests, Fig 1, shows that the retained ductility became smaller the larger the prestrain. However, this decrease is less than the amount of prestrain or, in other words, less than the decrease in ductility at the prestraining temperature. These effects of prestraining are fundamentally identical with those observed by Bridgman3 when a steel was prestrained (in tension) under hydrostatic pressure and then subjected to a regular tension test. It appears, therefore, that the basic effect of prestraining under conditions which yield a higher ductility than the (subsequent) testing procedure, consists of gradually increasing the total ductility of the metal from the initial low value of testing to the higher value of prestraining. On the other hand, all annealed steels, if cold worked by tension at room temperature and then tested at a lower temperature, provided that some ductility is retained, showed a far more complex behavior than that discussed above. This relationship is exemplified by Fig 2, for three pearlitic steels.4,5 These particular steels were selected because of the various shapes of their ductility-prestrain curves. All three steels, and any other investigated so far, suffered a rapid decrease in retained (and consequently also in total) ductility when subjected to small pre-strains. Then, after exceeding a certain prestrain it was generally observed that the ductility recovered.* This rather complex behavior of annealed steels may be tentatively correlated with the presence of stretcher strains at small restrains. Heat treated steels do not exhibit stretcher strains. This fact might possibly explain their simpler prestrain-retained ductility relationship. The destructive effect of these stretcher strains may possibly be associated with the presence of triaxiality, which may occur in any highly non-uniform stress and strain state (and which is retained as residual stress after unloading). Even a small degree of triaxiality may then cause a reduction in ductility, or even embrittlement at a sufficiently low testing temperature. The discussion presented above deals with the effects of cold working at a high temperature on the fracturing

Jan 1, 1950

By G. R. Smithson, John E. Hanway

This paper, the first of two papers covering the development of a metallurgical process for the treatment of a complex ore, describes the bench-scale experimental Program undertaken as a basis for initial process design. The results of using various potentially applicable process steps are detailed and the basis for selecting certain of these steps for Pilot-plant development is outlined. A process consisting of the steps of sulfate roasting, leaching, copper recovery, solution purification, zinc electrolysis, and brine leaching for lead recovery was recommended for further study. THIS paper describes the bench-scale development of a sulfate roasting process designed to recover copper, lead, and zinc from a complex ore. The extrapolation of the bench-scale results to pilot-plant design and the results of pilot-plant operation will be described by Lund, et al.' in a subsequent paper. Several years ago, the research divisions of the St. Joseph Lead Co. became responsible for the development of a metallurgical procedure to treat a complex sulfide ore containing copper, zinc, and lead sulfides. The primary objective was to devise a procedure which would permit economic recovery of the nonferrous values. As could logically be expected, the study of conventional flotation procedures was undertaken; in addition, however, because the physical nature of the mineral association in the complex ore indicated that physical methods of ore beneficiation might not prove to be entirely satisfactory, a program also was established to investigate alternative methods of direct metallurgical treatment for recovery of the metal values. Exploratory test work by the St. Joseph Lead staff led to the conclusion that a sulfate roasting technique represented the most attractive approach for a direct metallurgical process. Sulfate roasting would provide for the selective conversion of the nonferrous values to forms soluble in conventiona1.1 leaching agents and would permit their efficient separation from the insoluble iron and other gangue materials. It should allow efficient utilization of the thermal energy available from oxidation of the sulfide raw material, and might provide an opportunity for recovering byproducts such as iron and sulfur. The decision to evaluate a selective sulfation procedure as a basic processing step also was influenced by the excellent results obtained by the St. Joseph Lead Co. in using this procedure for the recovery of cadmium from zinc sulfide concentrates. The choice of selective sulfation as a major processing step served as a basis for an extended experimental investigation of the process with bench- and pilot-scale equipment to prove its feasibility. St Joseph Lead Co., aware that Battelle Memorial 1nstitute had participated in the development of several fluidized-bed sulfate roasting procedures, asked Battelle to undertake the bench-scale development of a suitable sulfation process. This paper describes the procedure used and the results obtained at Battelle in the treatment of the complex sulfide ore. EXPERIMENTAL WORK Nature of the Raw Material. The sulfide ore deposits of interest are essentially a massive sulfide, with the indivudual ore minerals being extremely fine grained and intimately intergrown with each other and with the associated gangue. The zinc in the ore is present mainly as sphalerite (ZnS), the lead as galena (PbS), and the iron either as pyrite (Fes2) or as pyrrhotite (FeS). Table I shows the chemical analysis of various individual samples of the ore. These analyses illustrate the variability of the ore body and impose a rather severe requirement on any type of metallurgical process—that of being able to tolerate probable wide variations in the assay of the head ore. The tentative flowsheet designed to serve as a guide for the initial experimental investigation of

Jan 1, 1962

By Louis P. Gignac

INTRODUCTION The selection of trackless equipment for underground mining can be a complex engineering problem due to the wide range of equipment sizes and operating modes. Computer simulation is particularly useful in estimating the performance of different systems for specific rock- handling problems. A hybrid simulator, incorporating some of the features of deterministic and stochastic simulation, was developed in order to handle not only queuing delays at loading and dumping points, but a1 so traffic interferences. Any number of vehicles can operate in any one of four basic modes (LHD, LAF, FEL, HFC) in parallel or in series. If the units use common roadways, loading and dumping points, certain operating delays will occur and be registered by the simulator and thus give a better evaluation of the marginal productivity of each additional unit. Based on a typical layout of drawpoints and ore passes for the sub-level stoping method, productivity and operating costs of different rock-handling systems will be examined. 1 . COMPUTER SIMULATION Numerous applications of computer simulations are reported in the 1iterature for various mining problems. Depending on the complexity of the system to be studied, simulation models were conceived with different degrees of sophistication. Three different types of simulators are generally recognized: stochastic, deterministic, and hybrid. Stochastic or Monte Carl o simulation randomly generates items, transactions, or events from some population defined by a frequency distribution and produces some expected future situations. Because this type of simulation is governed by the input of probability distributions, it requires a detailed knowledge of the system to be simulated; it implies expensive and time-consuming studies and reports to gene- rate this input information. A major short- coming of stochastic techniques is in new equipment evaluation, where the lack of data is unavoidable, and in new system design where the conditions are outside the range of the known historical behavior of the equipment. However, probabilistic simulation is almost essential for the study of cyclic queues and traffic problems. Deterministic simulation studies a system by generating performances on the basis of the mechanical capabilities of the vehicles and the physical limitations of the mining scheme. It is based on the engineering principle that the engine converts its energy into a rimpull at the wheels, which is in turn opposed by the rolling resistance and the grade of the ground; the machine is accelerated or decelerated until the tractive and resistive forces are in equilibrium, at which point it moves at constant speed. The information required by this technique, such as rimpull charts and equipment weight, is readily available from equipment suppliers. However, equipment performance at the mining site is also dictated by human and environmental conditions and changes with time and usage. For this reason, deterministic simulation generally overestimates the system capabilities; these must then be adjusted by efficiency factors based on observation and experience. Recently, hybrid simulation models, using both stochastic and deterministic techniques, have been built with some of the events generated stochasticly and others being deterministic. This compromising approach originated at the Pennsylvania State University. O'Nei1 (1966) designed a simulator for truck-and- shovel operations that allows for transportation from multiple faces to mu1tiple destinations. Each truck performs according to its mechanical capabilities while its loading and dumping time and its load fluctuate according to specific probability distributions. A major advance in the simulation of mining systems is due to Sanford's model (1969) of underground coal mining operations. The originality of the model is in the use of an Executive System Control which sets up the initial system, de- fines the operation conditions , and instructs continuously four sub-assemblies representing shuttle cars, trains, continuous miners , and conveyors, which in turn generate a feed-back of their movement to the Executive Control System for further instructions. The model has enough flexibility to simulate simultaneous and sequential jobs that characterize any dynamic system. Sanford's early work evolved slowly to what is known today as the Under- ground Materials Handling Simulator for coal mining (Manula, 1974).

Jan 1, 1981

By M. M. Austin

PURE metallic tantalum, from a practical standpoint, is one of the newer developments in the metal field. Although it was used as filament in incandescent lamps in 1906, only within the last five years has the metal been available in sufficient quantity and suitable form for more general application. In addition to corrosion-resisting properties and high melting point, the metal has an ability to withstand unusual amounts of cold working. It affords some striking demonstrations of block movement during plastic flow.

Jan 1, 1930

By R. H. Frazier, C. H. Lorig, F. W. Boulger

This investigation establishes the effect of ferrite grain size resulting from various heat treatments on the transition temperature of a semikilled steel plate. Different austenitizing temperatures and various cooling rates were used. The ductile-brittle transition temperatures were determined by the Navy tear test and the keyhole Charpy test. THE data presented in this paper deal with quality characteristics of ship-plate material which were investigated in a research project sponsored at Battelle by the Bureau of Ships, Dept. of the Navy. Specifically, the object of this investigation was to establish the effect of ferritic grain size (resulting from various heat treatments) on the so-called transition temperature of ship-plate steel. Transition temperature is not a fixed property of steel. It is derived from a series of static or dynamic tests made at various temperatures and is qualified by specifying the type of test employed as well as the testing criteria. Because in earlier investigations of ship-plate quality1,2 the so-called Navy tear test and standard notched-bar tests (keyhole Charpy) proved to be useful in interpreting instances of brittle behavior of ship plate in service, these tests were used in the investigation reported in this paper. By definition,' in the Navy tear tests the highest temperature at which one or more of four specimens breaks with a brittle fracture (that is, when less than 50 pct of the fracture area has a dull fibrous texture) is termed "transition" temperature. In the Charpy tests, the 12 ft-lb level of energy absorption was used as a criterion indicating the "transition" temperature, although other levels of energy absorption were also used for comparison. Earlier work" on ship-plate steels indicated that the temperature at which ship plate is finished has a very significant effect on its notched-bar properties. Plates rolled in the laboratory, where the finishing temperature can be carefully controlled, showed a 16°F decrease in tear test transition temperature when the finishing temperature was lowered 200°F (from X" to Y°F). The same plates showed a drop of 10°F in the keyhole Charpy transition temperature from the same decrease in finishing temperature. Commercially finished plates' exhibit a similar trend. When the ferrite grain size of the hot-rolled laboratory plates was determined, a close relationship was found between the ferrite grain size and the notched-bar transition temperature." " he indicated relationship between grain size and transition temperature was in agreement with the findings on low carbon steels of Hodge, Manning, and Reichhold' despite the differences in composition of the steels. The cooling rate after rolling varies from one steel plant to another. This variation changes the micro-structure" and appears very likely to affect the notched-bar properties of the steel plates. In the investigation summarized in the present paper, heat treatments simulating finishing practices in the hot rolling of ship plate were used in order to vary the ferritic grain size. It is believed that the indicated relationship between grain size and transition temperatures of the ship-plate material will prove useful in estimating the effect of rolling temperature and of cooling rates from rolling temperatures on the notched-bar properties of semikilled steel plate. Material The semikilled steel plate used in this investigation was a ¾ in. hot-rolled plate from an open hearth heat. Other plates from this heat have been used on many other studies performed for the Ship Structure Committee," "," and the heat has been identified as project steel "A". The chemical composition of the plate1 was 0.25 pct C, 0.49 pct Mn, 0.011 pct P, 0.045 pct S, 0.04 pct Si, and 0.004 pct N.

Jan 1, 1956

By Clark Millison

The core recorder, a mechanical instr-ent for determining the exact depth at which core is recovered, drilled up or lost, is described. Examples of charts from the recorder are explained and interpreted. The uses of the core recorder are discussed. INTRODUCTION In the experience of geologists and engineers during coring operations on drilling wells, many will recall the times when a full core was not recovered and particularly when the requirement was urgent that they know exactly what part of the core was lost. To make this determination, the core recorder was designed. Its uses are many, and only the most obvious will be presented here. Although this discussion will be limited to drilling wells for petroleum, the core recorder can be used in any type of coring operation. The principle of the core recorder is the proportional reduction of the motion of core entering or dropping out of the core barrel to a stylus moving in such a manner as to record the reduced motion on a chart. The time element is registered on the same chart by the revolution of a clock which turns the chart drum. Thus the exact amount of core entering or dropping out of the core barrel is charted and the time of such entry or exit from the core barrel is precisely correlated to the depth at which the core is recovered or lost. Lack of movement of the stylus which is revealed by the continued revolution of the chart drum indicates that no core is entering the barrel. The principles are accomplished by an instrument placed inside of the core barrel. A cylinder which contains the clock and mechanical apparatus has a diameter smaller than that of the core barrel. Near the top of the cylinder is an eighteen hour clock which turns the drum that contains the chart. Near the bottom of the instrument is a serrated wheel which by friction against the inside of the core barrel is turned as core enters or drops out of the barrel.

Jan 1, 1949

By Clark Millison

The core recorder, a mechanical instr-ent for determining the exact depth at which core is recovered, drilled up or lost, is described. Examples of charts from the recorder are explained and interpreted. The uses of the core recorder are discussed. INTRODUCTION In the experience of geologists and engineers during coring operations on drilling wells, many will recall the times when a full core was not recovered and particularly when the requirement was urgent that they know exactly what part of the core was lost. To make this determination, the core recorder was designed. Its uses are many, and only the most obvious will be presented here. Although this discussion will be limited to drilling wells for petroleum, the core recorder can be used in any type of coring operation. The principle of the core recorder is the proportional reduction of the motion of core entering or dropping out of the core barrel to a stylus moving in such a manner as to record the reduced motion on a chart. The time element is registered on the same chart by the revolution of a clock which turns the chart drum. Thus the exact amount of core entering or dropping out of the core barrel is charted and the time of such entry or exit from the core barrel is precisely correlated to the depth at which the core is recovered or lost. Lack of movement of the stylus which is revealed by the continued revolution of the chart drum indicates that no core is entering the barrel. The principles are accomplished by an instrument placed inside of the core barrel. A cylinder which contains the clock and mechanical apparatus has a diameter smaller than that of the core barrel. Near the top of the cylinder is an eighteen hour clock which turns the drum that contains the chart. Near the bottom of the instrument is a serrated wheel which by friction against the inside of the core barrel is turned as core enters or drops out of the barrel.

Jan 1, 1949

By Prof John E. Church

ONE of the most striking phenomena connected with the mines on the Comstock lode is the extreme heat encountered in the lower levels. This heat is not due to the burning of candles, heat of the men, and decomposition of timbers, all intensified by bad ventilation, as was the case nearer the surface. It proceeds from the rock, which maintains constantly a temperature very much higher than the average of the atmosphere in Nevada. The heat of these mines is a matter of more than usual interest, for they are the only hot ones now worked in the United States, and both in the present temperature encountered and in the increase which is to be expected as greater depths are reached, they appear to surpass any foreign mines of which we have a record. Hot mines are known also in other countries, as in the tin and copper lodes of Wales, where one of the veins worked by the United Mines is known as the hot lode. It has springs which discharge water at a temperature of 116' Fahrenheit, the depth being 220 fathoms, or 1320 feet. The heat of the air in these workings is. given at 100' to 113' Fahrenheit. The air is bad, and the heat in the drifts seems to be traceable to defective ventilation rather than to the real necessities of the case. Air is supplied through a small pipe, and is drawn from a place where the temperature is 95' Fahrenheit. Under such circumstances it is not surprising to read that in this hot mine the air is hotter than the rock, a state of things which I hare never observed in the Comstock. Other mines have been reported to the British Coal Committee as having temperatures of 106" Fahrenheit and thereabouts, but the only positive comparisons that are available at this writing are the following, all from Cornish mines : Mine. Depth Temperature. in feet. Air. Rock. Tresaveau,.....1581 86° 83° to 85° Consolidated Mines,. .. 1500 87° 86° " " . 1722 94o 93° " L .. .. 1764 94o to 96° 921/2° to 931/2°

Jan 1, 1879

By John A. Prof. Church

ONE of the most striking phenomena connected with the mines on the Comstock lode is the extreme heat encountered in the lower levels. This heat is not due to the burning of candles, heat of the men, and decomposition of timbers, all intensified by bad ventilation, as was the case nearer the surface. It proceeds from the rock, which maintains constantly a temperature very much higher than the average of the atmosphere in Nevada. The heat of these mines is a matter of more than usual interest, for they are the only hot ones now worked in the United States, and both in the present temperature encountered and in the increase which is to be expected as greater depths are reached, they appear to surpass any foreign mines of which we have a record. Hot mines are known also in other countries, as in the tin and copper lodes of Wales, where one of the veins worked by the United Mines is known as the hot lode. It has springs which discharge water at a temperature of 116° Fahrenheit, the depth being 220 fathoms, or 1320 feet. The heat of the air in these workings is given at 100° to 113° Fahrenheit. The air is bad, and the heat in the drifts seems to be traceable to defective ventilation rather than to the real necessities of the case. Air is supplied through a small pipe, and is drawn from a place where the temperature is 95° Fahrenheit. Under such circumstances it is not surprising to read that in this hot mine the air is hotter than the rock, a state of things which I have never observed in the Comstock. Other mines have been reported to the British Coal Committee as having temperatures of 106° Fahrenheit and thereabouts, but the only positive comparisons that are available at this writing are the following, all from Cornish mines * Read by permission of Lieut. Geo. M. Wheeler, Corps of Enginerrs, U. S. Arm J, in charge of U. S. Geographical and Geological Surveys, west of the 100th meridian.

Jan 1, 1879

By P. V. Faragher

A metal or alloy finds its place in commerce in proportion to its ability to serve certain purposes better and more economically than other materials. While there is some overlapping of the fields of application of the various metals under discussion in this symposium, each one has its uses for which it is especially adapted. While aluminum is the most recent of the metals to enter the field, the development of the industry has been based on its peculiar properties, by virtue of which new uses for non-ferrous metals have been created. There has been substitution of this new metal for other members of the group but there has been a far greater development in entirely new fields. In common with the other non-ferrous metals, aluminum is resistant to atmospheric corrosion. It also withstands the action of many of the common chemical reagents, strongly alkaline substances being the notable exceptions. The outstanding properties on which the application of aluminum is based are its low specific gravity and its ease of fabrication into the forms in which it is used. It is noteworthy that this property of specific lightness is retained in all the commercial aluminum-base alloys. This statement does not apply to aluminum bronze; this is more properly a copper-base alloy, since aluminum enters into its composition to the extent of only about 10 per cent. None of the commercial casting alloys of aluminum has a density exceeding that of the parent metal by more than about 10 per cent., and some are actually lighter. In the so-called "strong alloys" of aluminum in which strengths comparable to that of mild steel are developed by heat treatment, the greatest increase in density is only slightly more than 3 per cent., and one of these, also, is lighter than aluminum. This property of lightness combined with the desirable mechanical properties of the alloys, makes aluminum especially suited for parts of moving assemblies where saving in power, as well as a decrease in stresses resulting from inertia and vibration, are of importance.