Search Documents

By J. S. Ross

Few Canadians realize the role of their domestic industrial minerals industry because it is over-shadowed in production value by a large metallic minerals industry. But since 1960, Canada has had a reasonably well balanced, mature industrial minerals industry; and although the nation's sparsely scattered population has not been able to support an industrial minerals industry in a manner comparable to the domestic and foreign support given the metal mining sector, Canada is, nevertheless, exporting large quantities of higher priced nonmetallic minerals. Production of many of the basic minerals had been firmly established long before 1960, but it was not until the late 1950's that the output of cement, salt, titanium dioxide pigment and slag, sulfur, gypsum and sodium sulfate reached relatively high levels. Shortly after 1960, the significant potash and lithium chemicals industries were established and their effect is just now being realized.

Jan 11, 1964

By John H. Walthall, Raymond L. Copson, Travis P. Hignett

In October 1942, the War Production Board requested the Tennessee Valley Authority to undertake investigations to determine the feasibility of producing alumina suitable for reduction in aluminum cells, from clays and other domestic materials, by a lime-sintering, soda-ash leaching process. The work was undertaken by the chemical engineering staff of the Authority under the general direction of the War Metallurgy Committee of the National Academy of Sciences. The investigation included small-scale tests to determine the most suitable conditions for the process, and construction and operation of a pilot plant to obtain data for evaluation of the process and for design of a plant. The results of this investigation are described in the present paper. Sources of Alumina Alumina for the commercial production of aluminum is obtained from bauxite by the Bayer process. The tremendous demand for aluminum for wartime uses is causing rapid exhaustion of the high-grade bauxite deposits in the United States. On the other hand, there is an abundance of aluminous materials such as clay and lower grades of bauxite, which are not suitable for treatment by the Bayer process because of their high silica content. The Tennessee Valley Authority has conducted research and pilot-plant work for more than 5 years on methods for the production of alumina from clay and low-grade bauxite. Particular attention has been given to the high-grade white kaolin found in Carroll County, Tennessee. Exploratory drilling has demonstrated that at least 4 1/2 million tons of kaolin containing in excess of 34 per cent AlzOI is available in this area by strip-mining methods. It has been estimated that hundreds of millions of tons of clay of similar quality occur in the Tennessee Valley region. The Process The process is illustrated in the flowsheet (Fig. I), and consists essentially of the following steps: I. Heating a mixture of clay and limestone to form a sinter containing calcium aluminate and dicalcium silicate. z. Leaching this sinter with a dilute sodium carbonate solution, to form a sodium aluminate solution and a calcium carbonate, calcium silicate residue, which is discarded. 3. Treating the sodium aluminate solution with carbon dioxide to precipitate aluminum trihydrate and regenerate the sodium carbonate solution, which is recycled. 4. Heating the aluminum trihydrate to produce alumina. The process was considered promising because of the abundance and cheapness of the two raw materials, clay and limestone; and because, as compared with an acid process, smaller amounts of critical

Jan 1, 1944

By Harold M. Mooney

WHEN apparent resistivity data are taken with the symmetrical Wenner 4-electrode spread, a fixed center position is used and readings are taken for values of electrode separation. Basic data consist of apparent resistivity plotted against separation of adjacent electrodes. The interpreter attempts to infer geologic structure, such as the depth to discontinuities and the nature of subsurface earth materials. An earlier paper1 described methods for interpreting resistivity data. All of these involve a severe assumption, namely that the earth in the region of interest consists of horizontal layers, electrically homogeneous and isotropic. The actual earth never satisfies this assumption exactly and may deviate from it so much that none of the above methods can be applied. Attempts in three directions have been made to modify the assumption so that it approaches known geologic complexity more closely.

Jan 12, 1954

By R. S. Dean

THE first attempt to establish an equilibrium diagram of the lead-antimony series was made by Roland-Gosselin1 in 1896. This investigation classified the system as a purely eutectiferous one, with the eutectic at 12.5 per cent. antimony and 228° C. In the next year, Stead2 placed the eutectic temperature at 247° C. The error in temperature made by Roland-Gosselin, however, has been perpetuated in the literature with a remarkable degree of persistency; this value was accepted by Campbell (1902), and Ewen (1910),3 and will be found in the last edition of Desch's3 Metallography (1922). Gonterman's investigation, made in 1907, was the most complete one available at the time the present investigation was started. He concluded' that the system was a simple eutectiferous one and placed the eutectic at 13 per cent. antimony and 247°C. Other investigations by Tammann (1907),5 Garbow (1909),6 Rudolfi (1910),7 Loebe (1911),8 and Leroux (1913)9 added little, if any-thing, to Gonterman's diagram. A number of investigations have been made of physical properties of the alloys. The electrical conductivity of the series was studied by Matthiessen (1860)10 and by A. W. Smith (1921);" the thermoforce by Rudolfi (1910),12 and Pelabon (1923);13 the specific heat by Durrer

Jan 2, 1926

By A. L. Jr. Pozzi, A. O. Garder, D. W. Peaceman

A new numerical method is proposed for the solution of multidimensional miscible displacement problems. Besides the usual stationary grid associated with numerical procedures, the method uses moving points for which positions and concentrations are computed each time step. Based on the method of characteristics for treating combined transport and dispersion, the method applies equally well to any number of dimensions and, in contrast with other numerical procedures, properly takes into account the physical dispersion, no matter how small. Extensive tests show that accurate solutions of one-dimensional problems can be obtained over a wide range of values of the dispersion coefficient, including zero. They also show that the moving points do not need to be uniformly spaced, and that increasing the number of moving points beyond 2/grid interval does not significantly improve the accuracy of the solution. Two-dimmsional calculations using the new method were carried out to simulate laboratory model displacements in which gravity caused overriding of solvent. Good agreement between observed and computed profiles and measured and computed concentrations of produced fluid was obtained for a viscosity ratio of 1.89; at higher viscosity ratios, fair agreement was obtained Computed results were found to be significantly affected by vertical dispersion, and negligibly affected by dispersion in the direction of flow, in agreement with conclusions based on experimental observations. INTRODUCTION Although miscible displacement processes are potentially of great economic significance, limited progress has been made in developing mathematical methods for predicting the outcome of a solvent flood. Because of the complexity of the partial differential equations which describe multidimensional miscible displacement, numerical methods are a natural approach to their solution. The task of finding suitable numerical approximations to one of the partial differential equations, which involves both dispersion and convective transport, has been particularly difficult. Dispersion in the absence of transport is described by the heat flow equation, a second-order equation of parabolic type. This equation has been very successfully treated by numerical methods. Transport in the absence of dispersion is described by a first-order equation of hyperbolic type. This equation has been treated numerically with some success in one dimension, both by Lagrangian and Eulerian techniques, 1.2 but extension to two or more dimensions has not been satisfactorily accomplished. Usually one of two things happens: either the numerical solution develops oscillations or it becomes smeared by artificial dispersion resulting from the numerical process. When transport and dispersion are considered simultaneously, this numerical dispersion may dominate the low physical dispersivicy that generally characterizes miscible displacement. Stone and Brian2 have developed a new difference equation for treating combined transport and dispersion in one dimension. By suitable choice of certain parameters, they succeeded in markedly reducing both oscillation and numerical dispersion. However, a satisfactory extension to higher dimensions has not yet been found. Peaceman and Rachford3 presented a centered-in-time and centered-in-distance difference equation combined with a 1,transfer of overshoot" procedure which was demonstrated to work well in one dimension. The technique was applied to the two-dimensional miscible displacement problem, but subsequent calculations with zero dispersivity showed little change in results compared with the calculations they presented. This indicates that their method involved a numerical dispersion of the same order as the physical dispersion. The present paper describes an alternate method for solving the combined transport-dispersion

Jan 1, 1965

By Alan Morris

SEASON cracking of brass has received wide attention and there is a wealth of technical literature on the subject. Its causes are fairly well understood and means for its prevention are inexpensive and effective, .so that the frequency of failures from this source has diminished of recent years. But its sister phenomenon, the failure of annealed brass by reason of applied tensile stress plus a certain type of corrosion, has received less attention, though it has been responsible for occasional more or less troublesome cases of cracking of brass in service. The work described in the following pages was undertaken about two years ago to determine the relative resistance of various commercial brass mixtures to stress-corrosion cracking, and to learn something of the controlling factors. By stress-corrosion cracking we mean the cracking of brass free- from internal stresses by reason of applied tensile stress and simultaneous attack by certain corrosive agents. Rogers,1 in discussing a paper by Hatfield and Thirkell, says : "He had also applied a solution of mercuric salt to tensile test pieces of brass whilst they were under stress in the testing machine. At very moderate stresses such test pieces cracked, and very readily broke." Moore, Beckinsale and Mallinson2 subjected test pieces to simultane-us corrosion and tensile stress. In order to determine the minimum stress detectable in brass by the mercurous nitrate test, tensile samples were placed under stress and treated with mercurous nitrate solution. They found that brass stressed below a minimum did not crack.

Jan 1, 1930

By E. G. Leonardon, D. C. McCann

The search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out continuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum of useful samples. A device for taking samples of the formation from the walls of a hole therefore offers the possibility of recovering cores from zones otherwise lost as a source of this type of information. Furthermore, by coring

Jan 1, 1939

By J. H. Hollomon, L. D. Jaffe

The hardenability concept has become widely used during the last few years for the choice and substitution of steels. Before the work of Grossmann,1 the systems for predicting hardenability from chemical composition could be used only over a narrow range of composition. Grossmann introduced a comprehensive system, which has been effective in calculating the hardenability of most types of moderate or low-alloy steels. However, occasions often arise that require the calculation of the hardenability of high-alloy steels from their chemical compositions. Experimental determinations of the hardenabilities of such steels indicate that the Grossmann system predicts much greater hardenabilities than are realized. The fact that cases do arise in which the Grossmann method does not apply indicates that the fundamental hypothesis of the system may not be generally applicable. It seems advisable to re-examine not only Grossmann's system but also the concept of hardenability itself. Hardenability If steel parts are to possess a martensitic structure after quenching, they must first be austenitized and then cooled through the pearlite and bainite transformation ranges sufficiently rapidly to avoid the formation of pearlite, bainite, and pro-eutectoid products.* If, on cooling, these transformations are avoided, the resulting structure can consist only of martensite (and retained austenite). The hardenability of a steel is measured in terms of the severity of the cooling conditions necessary to avoid the pearlite and bainite transformations. The less rapid is the cooling necessary to prevent the formation of bainite and pearlite, the higher is the hardenability. The pearlite and bainite reactions appear to be differently affected by the alloying elements. Not only is this indicated by the published isothermal transformation data, but recent work by Zener2 affords a rational interpretation of the differing effects of the alloying elements. Manganese,3 for example, appears to decrease the rates of the pearlite and bainite transformations by equal percentages, while molybdenum45 is approximately 10,000 times more effective in retarding the pearlite than in retarding the bainite transformation, on the basis of isothermal measurements. In some steels, the formation of bainite restricts the formation of martensite while

Jan 1, 1947

By L. D. Jaffe, J. H. Hollomon

The hardenability concept has become widely used during the last few years for the choice and substitution of steels. Before the work of Grossmann,1 the systems for predicting hardenability from chemical composition could be used only over a narrow range of composition. Grossmann introduced a comprehensive system, which has been effective in calculating the hardenability of most types of moderate or low-alloy steels. However, occasions often arise that require the calculation of the hardenability of high-alloy steels from their chemical compositions. Experimental determinations of the hardenabilities of such steels indicate that the Grossmann system predicts much greater hardenabilities than are realized. The fact that cases do arise in which the Grossmann method does not apply indicates that the fundamental hypothesis of the system may not be generally applicable. It seems advisable to re-examine not only Grossmann's system but also the concept of hardenability itself. Hardenability If steel parts are to possess a martensitic structure after quenching, they must first be austenitized and then cooled through the pearlite and bainite transformation ranges sufficiently rapidly to avoid the formation of pearlite, bainite, and pro-eutectoid products.* If, on cooling, these transformations are avoided, the resulting structure can consist only of martensite (and retained austenite). The hardenability of a steel is measured in terms of the severity of the cooling conditions necessary to avoid the pearlite and bainite transformations. The less rapid is the cooling necessary to prevent the formation of bainite and pearlite, the higher is the hardenability. The pearlite and bainite reactions appear to be differently affected by the alloying elements. Not only is this indicated by the published isothermal transformation data, but recent work by Zener2 affords a rational interpretation of the differing effects of the alloying elements. Manganese,3 for example, appears to decrease the rates of the pearlite and bainite transformations by equal percentages, while molybdenum45 is approximately 10,000 times more effective in retarding the pearlite than in retarding the bainite transformation, on the basis of isothermal measurements. In some steels, the formation of bainite restricts the formation of martensite while

Jan 1, 1947

By E. G. Leonardon, D. C. McCann

The search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out continuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum of useful samples. A device for taking samples of the formation from the walls of a hole therefore offers the possibility of recovering cores from zones otherwise lost as a source of this type of information. Furthermore, by coring

Jan 1, 1939

By R. A. L. Black, J. E. Jennings

The problems of slope stability in open cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the orebody. This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ. A company embarking on open cast mining is faced with two basic questions: 1) will the venture be profitable and 2) can it be carried out with safety? The two questions are obviously interrelated because both depend upon the slope angles adopted for the pit. The cost of open cast mining depends largely upon the stripping ratio, defined as the volume of overburden that must be removed to the volume of ore recovered. The steeper the slope angles, the more favorable the stripping ratio, but the stability of the slopes, and therefore the safety of men and materials in the pit, require that the angles be made relatively flat. Consequently, the design depends upon a compromise: the slopes must be steep enough to result in economical mining and flat enough to ensure safety. Today there is a world trend towards deeper mining by open cast methods. This is mainly due to the higher cost of underground mining and the lower cost of open excavation resulting from the introduction of large modern earth and rock-moving machinery. Deeper open cast mining has led to a very great increase in the volumes of wasted overburden, and much thought is being given to the considerable economic benefits which would result if pit slopes could be made steeper by even one or two degrees. The result has been an increasing interest in research into slope stability problems in the expectation that the application of scientific principles will provide solutions leading both to economies and to more predictable operation of the mines. In at least four places, the U.S., Australia, Western Germany and Southern Africa, comprehensive investigations are at present in progress, and it is the object of this paper to review some of the more important aspects of these programs. RELATION BETWEEN ECONOMY OF OPERATION AND SLOPE ANGLES The main object of any industrial enterprise in a free economy is to make a profit. In mining, where profits must be made from a wasting capital asset, a further definition of the profit motive is imposed, namely that the economic aim should be to maximize the total possible profit. But since profits deferred for a number of years are not as valuable as profits that are immediately available, it is usual to discount deferred profits at some rate of interest which reflects their current or present value in the hands of the investor. Thus, in mining the logical aim can be defined more closely still: to maximize the present value of the total future profits. In commercial terms the present value represents the market value of the operation as a going concern. Many factors enter into the forecast of current and future profits. They include the volume of production, the price of the salable product and the cost of production. Current profits can be estimated with reasonable accuracy by the operating engineers; but it is the task of economists and management to assess future trends in the mineral markets and in the economy as a whole, and together with the engineers, they can then estimate the future cost and profitability of the mining operations. In open cast mining, the rate of ore production once decided on remains a virtually constant factor unless a major change in the capital structure of the mine is made. But one factor over which the operator has a considerable measure of control is the ratio of the volume of ore mined to the volume of waste over-

Jan 1, 1963

By D. Y. Geng, Syd S. Peng

This paper analyzes the effects of geology and mining methods on surface subsidence factor, angle of draw and angle of critical deformation based on the results of 40 longwall subsidence profiles in the Northern Appalachian coalfield. Several equations were derived to show the relationships between those parameters. Furthermore, the equations were transferred and plotted in the form of several monographs for convenience of applications.

Jan 1, 1982

By J. W. Hickman, E. A. Gulbransen

In a previous paper' the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300' to 7o0°C. except for copper, wherc the range selected was 100' to 500°C. The results of these studies were presented in graphical form as existence diagrams of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviatiois in lattice Darameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: 1. The existence diagrams of various alloys. 2. The effect of the structure of the alloying metal on the existence diagram of iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body-centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K4²B, Nichrome V, Hipernik, Inconel, Stellite "²I," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1947

By E. A. Gulbransen, J. W. Hickman

In a previous paper' the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300' to 7o0°C. except for copper, wherc the range selected was 100' to 500°C. The results of these studies were presented in graphical form as existence diagrams of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviatiois in lattice Darameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: 1. The existence diagrams of various alloys. 2. The effect of the structure of the alloying metal on the existence diagram of iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body-centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K4²B, Nichrome V, Hipernik, Inconel, Stellite "²I," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1947

By C. Scala, F. Bernstein

General expressions are derived relating the streaming potential to the electrochemical potential of a permeable junction separating two electrolytic solutions. By the methods of irreversible thermodynamics, these potentials are related to the flux of mobile species arising from differences in pressure and chemical composition. The flux is conveniently expressed as a transference number, the equivalents of a mobile species transferred through the junction per faraday of electricity. At constant pressure, the flux equation gives the electrochemical potential across the permeable junction. The streaming potential across the junction is obtained by imposing the condition of constant chemical composition. The familiar expression for the borehole SP is shown to be a particular solution of the general flux equation. The derived exprersions were verified in experiments with seven shale samples. Both the theory and experimental data provide additional proof of the presence and magniturle of the streaming potential in shales. INTRODUCTION In the interpretation of electric logs, there has been much concern over the correction to be made to the recorded SP for an electrokinetic or streaming potential originating from the difference in pressure between the mud column and the formation. It was long recognized by M. R. J. Wyllie that such an electrokinetic potential source mas in the mud cake opposite permeable sands.' More recently, M. Gondouin and C. Scala2 showed an additional but opposing electrokinetic source of potential to be in shale beds. Their work was supported by the very extensive and excellent work of Hill and Anderson.3 n the present contribution, the general relationships between the electrochemical potential and the corresponding streaming or electrokinetic potential are examined and clarified. A notable advance towards understanding the relation between the various sources of electrical potential in a borehole has been the application of the now common methods of irreversible thermodynamics to describe the passage of ions and water through charged electrolyte junctions such as in shales.' The advantages of these methods are twofold. Unlike classical thermodynamics, they can be applied to non-equilibrium sys- tems, i.e., systems in which flow takes place, provided the flow processes have reached a steady state. They also permit conventional thermodynamic properties to be related to the steady-state dynamic properties. These methods arc used here specifically to derive expressions relating the potential behavior of shales in terms of ion and water transport. Experimental verification of the expression for the shale streaming potential is given which in turn offers theoretical support to the existence of a streaming potential in shales.' Importantly, the relative contribution of transport parameters to the SP is clarified. The theoretical treatment is essentially that of Lori-mer, Boterenbrood and Hermans3 ut has been extended to derive the general expression for the SP.

By Alexander Squire

One of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three—chemical analysis, density, and hardness. The last of these may or may not be a pertinent characteristic, since the indentation hardness of many powdeied-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. It is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the pioperties of compacts formed from different types of powders are made on the basis of compacting pressures instead of density, and for this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By Alexander Squire

One of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three—chemical analysis, density, and hardness. The last of these may or may not be a pertinent characteristic, since the indentation hardness of many powdeied-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. It is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the pioperties of compacts formed from different types of powders are made on the basis of compacting pressures instead of density, and for this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By B. G. Klugh

In a paper before the Institute at Wilkes-Barre, Pa., June, 1911,' Mr. James Gayley discussed the application of this process to iron-bearing materials. The same author² described the results of operations at the plant at Birdsboro, Pa. The purpose of the present paper is to present further discussion of some techuical details involved in the operation of this plant, and of the theoretical and practical relations of this product to blast-furnace practice. Since Oct. 1, 1911, the Birdsboro plant has been in operation at the blast-furnace of the E. & G. Brooke Iron Co. The results have been highly satisfactory, although the material treated, being chiefly the flue-dust currently made by the furnace or taker] from the accumulated stock-pile, was excessively high, and yet not uniform, in carbon, so that the desirable control or regularity of the amount of fuel in the mixture treated could not be maintained. Nothing could more forcibly demonstrate the flexibility of the process than the fact that, under these conditions, the sinter produced was, in all cases, of excellent quality. The Dwight & Lloyd process, as such, slid its present highly-developed mechanical appliances were described by Mr. Gayley in the paper above mentioned. While the repetition of some particulars will be unavoidable in this paper, it will be confined to features bearing upon the metallurgical principles involved. According to the principle of the process, the finely-divided iron-bearing material to be sinterecl is intimately nlixed with

Jan 1, 1913

By William F. Butler, Mo-Hung Che

DEVELOPMENT OF MONEY AND MONEY STANDARDS This chapter is concerned with the rise, and then the decline and fall, of gold and silver as monetary metals. As a first step in tracing the history of this process, it is necessary to consider the nature of money, and the manner in which different forms of money have developed over the centuries. The origins of money go back into deepest antiquity. Once men ceased to be pure nomads and entered into even a rudimentary form of society such as clans or tribes, money had to be invented The first step was barter as farmers or hunters swapped their surplus products for things produced by artisans such as shoes, clothing, and simple tools. But such barter trading is inconvenient even in primative societies It is difficult to match up buyer and seller at any point in time There are problems in arriving at viable and acceptable terms of exchange. The accumulation of savings-wealth-is complicated. No one can be sure that a pile of furs, or wheat, or certainly fish or game can be used in the future to trade for other goods or services. So even prehistoric man saw the need for money. There was a need first for something to serve as a medium of exchange This was an essential first step in the process of specialization-or the division of labor. A farmer, a hunter, or a shoemaker could only devote his full efforts to his trade if he could be sure that he could exchange his surplus production for the other things he needed for existence. This required a medium of exchange-a form of money which would be broadly acceptable. Money was needed for two other reasons Some system of market prices was essential to facilitate the exchange of goods and services. This required some form of common denominator-some standard of value-to govern the exchange process. And there was also need for something to serve as a store of value, a place to put any excess production (savings) with the assurance that it can be used in the future to acquire a general range of goods and services. As a result, money, in one form or another, developed at a very early state in civilization. Yet the centuries have been marked by a search for a form of money which will possess in full measure all of the attributes in money-a reliable and universally acceptable medium of exchange, standard of value, and store of value. -A wide variety of things have been used as money at one time or another: shells, beads, stones, feather, metals, and even the teeth of sharks and dogs. Some of these things were obviously of little or no practical value. They were used because people had confidence in their continued acceptance as a medium of exchange. As the world evolved and as trading ex-

Jan 1, 1976

By Bradley Stoughton

[Secretary's Note.—TO avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.—J. S. 1 Introduction. This paper gives the results: first,, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castr ings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows : 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such 'as, for example, the wear of railroad-rails, of steel and chilled-iron rolls, car-wheels, etc. 2. These improvemerits seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example: A series of tests on cast-iron

Jan 1, 1913