Search Documents

By P. E. Baker

An experimental study of heat flow in steam flooding was carried out with steam displacing water in a plane-radial fluid-flow model. Temperature distributions in the model reservoir, overburden, and substratum were measured at frequent intervals during flooding by means of a fixed array of thermocouples. Heat losses to overburden and substratum and the division of heat between the steam and hot-water zones in the reservoir were calculated from the temperature data by performing numerical integrations over the appropriate volumes. Temperature profiles and heat distribution results are presented. Some results were (1) the fraction of injected heat that is lost to overburden and substratum, when expressed as a function of time, did not depend on injection rate; (2) a significant portion of the injected heat was contained in the hot-water zone ahead of and underlying the steam front in the reservoir. The division of heat between the steam and hot-water zones did depend on injection rate; and (3) considerable gravity override was observed. The experimental results are compared with those of several published theoretical studies of heat transfer in hot-fluid injection; approximate agreement on heat losses is found with some of the most idealized theories. A valid comparison cannot be made in regard to steam us hot-water zone; basic interpretation of the hot-water zone, in terms of a vertical steam front, is clouded by gravity override in the experiments. INTRODUCTION The experimental study reported here primarily concerns two problems of heat transfer in steam flooding that have economic and engineering importance. These are (1) the fraction of injected heat lost to the overburden and substratum, and (2) the division of the remaining heat between a zone containing steam and a zone of hot water at lower-than-boiling temperature. The volume of the steamed region, which has a direct effect on oil recovery, can be calculated readily from these results. Several valuable theoretical studies have been published on this problem, but no experimental tests of the theories have previously appeared. Tests were needed because the effects of the necessary simplifications in the theories could not be determined otherwise. The basic, untested theoretical problem is the effect of "decoupling" heat and mass transfer, and the resulting inability to include the effects of heat transfer and condensation on fluid flow. The theoretical problem solved so far has been a heat transfer problem in which fluid is present as a heat carrier and flows in a stipulated manner, either linear or plane-radial. The simplifications that have sometimes been made in regard to thermal conductivity by, for example, Marx and Langenheim,l Lauwerier2 and Thomas3 apparently do not have an important effect on heat loss calculations, although the results of the different methods disagree to a certain extent, as shown by Spillette4 and by Ramey.5 A recent paper by the author6 compared the results of experiments in hot-water flooding with several theoretical results and showed a rather poor agreement. It will be seen that the experimental heat loss results for steam flooding, however, show acceptable agreement. These comparisons are discussed in a later section. EXPERIMENTAL APPARATUS AND PROCEDURE The system studied was one in which a sand pack, initially water saturated and at a uniform temperature, was flooded with steam at a constant rate and temperature. The temperature distribution in the "reservoir" and adjacent "strata" was measured with an array of thermocouples, and heat losses were determined from these measurements. The sand pack contained no oil because the only concern of the experiments was heat flow, and it was important to have the flow pattern as simple

Jan 1, 1970

By Hugh Steele, Brower Dellinger

U. S. mining trends for 1956 continued steadily U+ S. uphill, technique and equipment advanced with the pull, and exploration and development of once mined districts attracted more attention than new areas. Expansion of the Ambrosia Lake district in New Mexico more than doubled known uranium ore reserves, and production began from several of the large new ore discoveries. In Canada the up trend was more spectacular, especially in exploration and development. To combat increasing problems arising from high labor costs, taxes, low grade orebodies, and dwindling discoveries, manufacturers and mining companies have continued to introduce new techniques and new products-reamer bits for enlarging small holes drilled by jacklegs, whup d'whups for drift mucking, Cryderman machines and over-the-head small crawler-type machines for shaft mucking, the 20-ton TL 220 four-wheeled tractor trailer unit for underground haulage, inertia-type dust collectors, roof bolting in conjunction with chain link fencing for wall support, wooden roof bolting using compression support of ground for wall support, and new one-use carbide bits.

Jan 2, 1957

The annual report f the Secretary of the Navy for the fiscal year, ending June 30, 1917, but including operations and recommendations up to Dec. 1 of that year, contains the following remark about the activities of the Naval Consulting Board. The members of the Institute who are members f this Board are William L. Saunders, Benjamin B. Thayer, Thomas A. Edison, Thomas Robins, Lawrence Addicks, Joseph W. Richards, W. R. Whitney, assisted by 47 other members f the Institute, in the capacity of associate members of the Naval Consulting Board. During the year, the work of this board, organized and approved by Congress in 1915, has increased very materially in importance and volume, its meetings have been frequent and the work of its individual members has been such in some cases as to occupy almost their entire time in the service of the Government. Some time before the active entry of this country into war the board called a special meeting to which were invited some 50 of the leading scientists and industrial managers, whose special study fitted them to advise on the methods of meeting the

Jan 2, 1918

By Arthur F. Colombo, David M. Hopstock

The Lake Superior region contains extensive deposits of potential iron ore in the form of fine-grained oxidized taconite. To help assure utilization of this resource in an environmentally sound manner, the U.S. Department of the Interior, Bureau of Mines, is conducting bench- and pilot-scale research using wet high-intensity magnetic (WHIM) separation. The advantages and disadvantages of WHIM separation in comparison with other feasible beneficiation methods are discussed. Pilot plant results are given for a flowsheet in which WHIM scavenging is used in conjunction with selective flocculation and flotation. A mathematical model for use in process optimization is given. Practical aspects of matrix selection and separator design for WHIM separation of fine particles are discussed.

Jan 1, 1980

By J. L. Lamont, W. Crafts

Studies of the effect of composition of steel on hardenability by Grossmann,' and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0'65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc' The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

By W. Crafts, J. L. Lamont

Studies of the effect of composition of steel on hardenability by Grossmann,' and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0'65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc' The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

By D. Watson, T. J. N. Grainger-Allan

A technique for studying the mechanism of the froth flotation process in which continuous froth removal does not take place but, instead, an equilibrium is reached between froth and pulp is described. A flotation cell, specially designed to facilitate equilibration, and froth and pulp sampling procedures are described. The main advantage of the technique is that the ability to measure the steady-state froth height allows froth-stability effects to be separated from pulp-process effects. In the flotation of hematite front quartz, linear relationships are found between airflow rate and froth height and between airflow rate and the ratio at equilibrium of mass of values in froth to mass of values in the pulp. A simple mechanistic interpretation of these results is given. It is suggested that froth-stability effects may play a more important role than hitherto allowed. In particular, the way in which concentration and size distribution of gangue particles may affect overall flotation rate is shown.

Jan 1, 1975

By Edward Martinez

Although the copper segregation process has been known as a method for treating oxide copper ores since the 1920's, the reactions involved in this process are still a matter of conjecture. However, the evidence turned up in a recent series of experiments at Asarco's Central Research Laboratories strongly indicates that some of the proposed reactions may not be occurring. Experimental work on oxide copper ores from the Sagasca mines in Chile led to the discovery of the copper segregation process in 1923. It was found that the reduction of the copper with coal at about 700°C occurred on the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge.

Jan 8, 1966

Discussion of the paper of M. B. YUNG, presented at the Pittsburgh meeting; October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2451 to 2458. T. T. READ, New York, N. Y.-I might .point out that this paper of Mr. Yung's is on a field that is comparatively little known. It is not as well known as the Kochiu tin field, of Yunnan, which is probably the third . in tin output of the world. This field under discussion is considerably further west and the tin which is produced here is, according to Mr. Yung, of somewhat higher grade than the Yunnan tin, and is used by the refiners at Hong Kong to improve the grade of the Yunnan tin. Most of you know that the tin from the Yunnan is shipped to Hong Kong, where it is refined and shipped to Europe. Mr. Yung points out that the Fu Chuan deposits are entirely alluvial and not found in any veins. They .differ in that from the Kochiu deposits, which Leclere says are "nullement alluvionels; leur origéne filonienne est de plus evidentes." Granite is the country rock here; doubtless the tin occurred in veins in the granite, and the deposits have resulted from the disintegration of the granite. This is a country of strong erosive agencies. The country is semi-tropical, and the rainfall is heavy, so that one would naturally expect deep surface erosion of this kind.

Jan 4, 1915

By H. S. Cannon, F. N. Rhines

IT. H. Hausner( Sylvunia Electric Products Inc., Bay-side, N. Y.)—The results reported by the authors are interesting because they contribute some information on the principles of sintering and also because of a certain practical value for the manufacture of powder . metallurgical parts in production. Pressed powder compacts are frequently sintered in a boat in several layers so that the lower layers are actually sintered under the weight of the upper layers and, therefore, are frequently deformed. The authors gave information on this deformation process by determining the effect of the load on the density. The experimental setup of the authors, however, has a disadvantage—that the sintering occurred in a cylindrical container so that the deformation was stopped in the direction of the diameter. The authors should have rather called this a study of hot-pressing than of sintering. I want to call the attention of the authors and others interested in sintering under load to the experimental work described by Dawihl and Rix.' These authors sintered cylindrical compacts under a lengthwise ten-sional load of 0 to 25 g and found that the shrinkage in length and diameter changes considerably with the load, but that the volume shrinkage is affected very little by the load. H. S. Cannon (authors' reply)—We wish to thank Dr. Hausner for calling attention to the experimental work of Dawihl and Rix. The fact that they found volume shrinkage little affected by varying tensional loads during sintering seems to support the contention that the forces due to loading are equivalent to and additive to the forces which cause densification. This contention is the basis of our comparison of sintering and creep.

Jan 1, 1952

By Earl R. Hoskins, James E. Russell

The electrical resistivity of rocks has been studied quite extensively, in particular, the effects of temperature and confining pressure on resistivity. References 1 through 6 at the end of this chapter pertain to electrical resistivity of rock and contain further references on the same topic. The present study is motivated by an interest in determining the in-situ properties of rock as well as the stress state of the rock and how these quantities are changing with time. Most of the previous work on the electrical resistivity of rocks has been directed toward saturated rocks at relatively high confining pressures and temperatures. The present study was oriented towards air-dry surface rock that might occur in mine pillars. The mean stress and temperature under such conditions are comparatively low. It has been demonstrated that the resistivity of rock is highly dependent upon the porosity. In fact, for saturated rocks, a relationship referred to as Archie's law has been established between porosity and electrical resistivity. In the case of saturated rock, the property that is actually being measured is the resistivity of the solid/fluid system. Since the resistivity of the fluid alone is usually much lower than that of the dry rock, it is understandable that the resistivity of a saturated rock is in general several orders of magnitude lower than the resistivity of a relatively dry rocli. For dry rock, it seems reasonable that the electrical resistivity should increase as microcracks open within the material. Since microcracks open as material is stressed closer and closer to its failure point, it appears that there should be a correlation between electrical resistivity

Jan 1, 1970

By Thomas L. Kesler

THE Cartersville mining district, 35 miles northwest of Atlanta, Ga., has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. However, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magnesian limestone. GENERAL GEOLOGY Geologic relations of the ore deposits of this district are more or less similar to those of many Appalachian districts. The lowermost Cambrian formation, heretofore called Weisner1 in this region, supposedly partly or wholly equivalent to the Erwin and Hesse quartzites as recognized to the northeast, is overlain conformably by the Shady [+] formation, also of Lower Cambrian age. In the Cartersville district, the sedimentary rocks of these formations were folded with increasing intensity eastward, and were recrystallized.

Jan 1, 1940

By N. Brown, R. Kossowsky

Plain carbon steels with 0.48 and 0.95 pct C were quenched and tempered at 705°C to produce carbide dispersions with spacings on the order of 1 p. The morphology of the structure consisted of a carbide-dislocation network. The strengthening due to the dispersion was found to vary linearly with M-½ where M is the mean free-ferrite path determined by the entire network. No preyield microstrain preceded the upper yield point. After prestraining, the lowest stress at which dislocation movement could be detected was 104 psi; this frictional stress was independent of the dispersion and prestrains up to 6.5 pct. The Cottrell-Petch equation for grain-size strengthening was used to discuss the dispersion strengthening in this investigation. The results support an impurity mechanism for the upper yield point rather than one based on the Johns ton- Gilman theory. IT was pointed out by Gensamerl that the mean free path in the matrix is the important variable which controls the degree of dispersion strengthening. Gensamer's data on steels showed a linear relationship between the yield point and the logarithm of the mean free-ferrite path. The first theory was by Orowan,2 who suggested the mechanism of dislocations bowing between particles, with the resulting relationship that where a is the yield point, P is the distance between particles, and G is the shear modulus. The Orowan equation applies to that range of dispersion where P is large compared to the particle size and the particles are not coherent, so that the matrix is essentially free of internal stresses. As was pointed out by Orowan, there are different degrees of dispersion which, in turn, will influence the strength-controlling mechanism. However, in this investigation, we wish to confine ourselves to the region of coarse dispersion, where the Orowan mechanism should, intuitively, be applicable. It was soon evident that the data, which existed at about the time that the Orowan theory was proposed, did not agree with the Orowan equation in that the actual strengthening was always greater than the theoretical predictions. Thus, Fisher, Hart, and pry3 modified the Orowan theory by suggesting that the Orowan process took place in the microstrain region preceding macroscopic yielding and the subsequent, rapid work hardening in the form of residual dislocation loops around the particles largely determined the observed macroscopic yield point. The F-H-P theory stated that the increment of strengthening due to the work-hardening mechanism was proportional to f3/2 where f is the volume fraction of the precipitate. F-H-P used data by Shaw, Shepard, Starr, and Dorn4 on A1 3-5 pct Cu to support their theory. Roberts, Carruthers, and Averbach5 were the first to make a microstrain study of dispersion strengthening, and they found that for steel the Gensamer relationship was obeyed. Hayman and Nutting6 suggested that in the case of tempered steel 1) the ferrite grain boundary was the primary obstacle and 2) the carbide particles simply formed part of the grain boundary obstacles. They found that the strength varied as G"" where G is the ferrite grain size. Turkalo and LOW' determined the structure of quenched and tempered plain carbon steel using a replica technique; they concluded that the carbide particles did not necessarily lie in the ferrite grain boundaries. When they defined the mean free-ferrite path as being determined by both particles and the ferrite path boundaries, their data obeyed the Gensamer relationship. Meiklejohn and skoda8 showed that the strengthening from iron particles in mercury was a function of the particle size and the distance between particles. Dew-Hughes9 explained the Meiklejohn and Skoda results by the following theory: 1) grown-in dislocations which surrounded the particles were produced by the thermal stresses during the time the material was cooled to the testing temperature, and 2) the observed strengthening was associated with the cutting of the grown-in dislocations by the glide dislocations. Ansell and Lenel10 proposed a theory in which the glide dislocations pile-up or surround the particle until the number of dislocations in the pile-up is sufficient to yield or fracture the particle. The resulting theory says that the yield point varies as p-1/2, where P is the distance between particles. The Ansell-Lenel theory is almost identical to the

Jan 1, 1965

By H. M. Chance

The Taviche district is about 12 miles from the town of Ocotlan in the State of Oaxaca, and about 250 miles south of the City of Mexico. Its altitude rises to something more than 5,000 ft.; and although within the tropics (latitude about 17° N.) the climate is mild and salubrious, neither excessively hot in summer nor cold in winter. The phrase, "perpetual spring," which has been applied to it, aptly describes the weather during my stay. Sugar-plantations, bananas and other tropical and semitropical fruits flourish in the valleys, while the hills

Jan 1, 1905

By C. M. Schwartz, A. E. Austin, W. B. Wilson

High-temperature X-ray diffraction studies were conducted with Th-U alloys with up to 10 wt pet U. The solid solubility of uranium in thorium as a function of temperature was determined by the method of lattice parameters. Thorium will dissolve up to 2.5 wt pet U at 950°, 4.5 wt pet U at 1150°, and 7.5 wt pet U at 1250°C. Determinations were made of the temperature of the transition of thorium and of the effect of uranium upon the transition. The a to ß transition for thorium was observed to occur at 1330' ±20°C. Mean coefficients of expansion were calculated for thorium and two alloys, and for ThO2 in contact with the thorium, using X-ray lattice-parameter data. Values obtained at 950° C for thorium and Tho2 were 12.1 and 9.40 X 10-6 per OC, respectively. Impurities obtained during the X-ray exposure were identified by diffraction and were essentially Tho2 and ThC, with two additional unknown phases being detected. The effect of the impurities upon the results is discussed. DIRECT investigation (i.e., high-temperature X-ray diffraction studies) of the phase diagram of thorium-rich uranium alloys has been shown to be necessary since recent work1 - has disclosed the presence of an allotropic transformation near 1400°C in pure thorium with the room temperature face-centered-cubic phase transforming to a body-cen-tered-cubic structure at the elevated temperature. The effect upon the transition of the addition of uranium to thorium and of the solubility of uranium in thorium at high temperatures remained unknown, yet was of interest in understanding fabrication procedures and elevated temperature use. The present work was undertaken to provide information in this area by determining the transition temperature, the effect of uranium on the transition temperature, and the solubility of uranium in thorium as a function of temperature. Experimental Work The high-temperature diffraction data were obtained using a camera especially designed for the purpose3 and capable of reaching temperatures in excess of 2000°C at pressures as low as 1 x 10." mm Hg. Temperature regulation was provided by regulating the power input to ±0.1 pet variation, and by regulating the water flow through the camera jacket to provide a constant thermal load. The X-ray sample was a rod nominally 80 mil diam, which was further turned down to 20 mil and then etched to 18 mil over 1/2 in. of one end. This was placed in the sample holder and mounted on the camera so that the smaller part was surrounded by a cylindrical tantalum-sheet radiation-type heating element. Diffraction from the sample was recorded on film after passing through a slot in the heating element and radiation-baffle shield and through beryllium vacuum windows. The X-ray film mounting was of the Straumanis type4 with a camera diameter of 114.59 mm. Since previous work of Chiotti' indicated that impurities considerably alter the transition temperature, chemical analysis of the arc melted iodide crystal-bar thorium samples was obtained prior to testing. The analysis disclosed the material to contain as low as 0.001 ±0,0002 wt pet H and 0.007 ±0.001 wt pet 0. Carbon was 0.003 wt pet and nitrogen less than 0.002 wt pet. This material was sealed in mild steel in an inert atmosphere and subsequently hot rolled to 3/8-in. diam rods at a temperature of 732°C. Following removal of the jacket, the material was pickled and cold swaged to 1/8-in. rods, from which the diffraction samples were prepared. The alloys were similarly prepared, with the uranium being added during arc melting. The uranium analyses of the alloys prepared appear in Table I. The experimental procedure for diffraction examination of the three samples of high-purity thorium differed from those of the Th-U alloys. The original practice, later modified, consisted of pumping down the camera with the diffusion pump on and then admitting liquid nitrogen to the cold trap of the system. This was modified for the Th-U alloys by maintaining liquid nitrogen in the cold trap at all times before and while the diffusion pump was heated. This minor change produced a reduction in the amount of carbon pickup by the sample during exposure to the diffusion-pump vapors. The sample was brought to the desired test temperature and exposed for 21/2 hr at pressures which were usually 2 x 10-6 mm Hg, or lower. Exposures were made at

Jan 1, 1959

By J. M. Locke

BRÜCKNER's revolving cylinders for roasting ores, etc., are now used at a number of the mills in Colorado and New Mexico, for the purpose of roasting and chloridizing silver ores, with highly satisfactory results, even from those cylinders of small size, erected before the many improvements of recent date. As examples of the larger improved cylinders, reference can be made to those erected at the Tennessee Reduction Works, Silver City, Grant County, New Mexico, and those which were built, in 1871, at the celebrated Caribou Silver Mill and Mines, Colorado, a mining enterprise which has proved so satisfactory as to have been lately sold to a Holland company for an enormous amount. These cylinders, as now constructed by Messrs. Lane & Bodley, of Cincinnati,, Ohio, are shown in Plate III, in which Fig. 1 is an elevation in perspective, Fig. 2 a longitudinal, and Fig. 3 a trans¬verse section. Fig. 4 is a sketch of a mill, with Brückner's cylinder. The exterior of the cylinder is a shell of boiler iron, 12 feet long by 5 feet 6 inches in diameter. The ends are partially closed with similar material, leaving in the centre a circular opening about 2 feet in diameter, bounded by a flange projecting several inches.. Upon one side is placed an opening closed by a hinged door. Upon the outside of the cylinder are bolted three bands, as shown in Fig. 1, in which the section of the first is square, and that of the third semi¬circular; the second, or middle band, is a strong spur gear. Passing through the cylinder are six pipes parallel to one another, in a plane at an angle of 15° to the axis of the cylinder; these pipes also lie in this plane at an angle of from 30° to 35° to the longitudinal, axis of the plane, as shown in Fig. 2, where the internal arrangement of the cylinder is seen, a perforated diaphragm being formed through part of the cylinder by means of perforated plates placed between

Jan 1, 1874

By A. B. Hersberger, R. S. Dean

Although it is obvious that in any flotation process we must have a froth, in recent years the development of collecting reagents has caused the possibilities of better frothing agents to be overlooked. Some investigators have even gone so far as to say that the number of satisfactory frothing agents was sufficient. A little consideration will show, however, that the reagents available in the past were far from ideal frothers. The properties of an ideal frother for flotation work may be set down as follows: 1. It must form in low concentrations a copious but not too persistent froth. 2. It must be insensitive to hydrogen-ion concentration of the pulp; that is, it must froth equally well in an acid or alkaline medium. 3. It must be insensitive to salts, even in high concentration. 4. It must be absolutely noncollecting to both sulfides and nonsulfides. 5. Its frothing properties must not be affected by collecting reagents, including soap, the most generally used nonsulfide collector. 6. It must readily emulsify and disperse any insoluble collecting agent that is likely to be used. Clearly the existing frothers do not qualify. Pine oil, for example, is an acceptable frother for many purposes but if used in soap flotation a delicate balance between pine oil and soap must be struck because, as pointed out by Coghill1, these two reagents are incompatible in certain concentrations. The objections to soap itself as a frother are obvious, and the cresols and their substitution products all have some collecting power and very little emulsifying power. The mechanism of frothing in flotation was early explained on the basis of the Harkins-Langmuir theory of oriented molecules.2 These investigators showed that if an organic compound having an unsym-metrical molecule (in which one end of the molecule contained water-

Jan 1, 1939

By R. S. Dean, A. B. Hersberger

Although it is obvious that in any flotation process we must have a froth, in recent years the development of collecting reagents has caused the possibilities of better frothing agents to be overlooked. Some investigators have even gone so far as to say that the number of satisfactory frothing agents was sufficient. A little consideration will show, however, that the reagents available in the past were far from ideal frothers. The properties of an ideal frother for flotation work may be set down as follows: 1. It must form in low concentrations a copious but not too persistent froth. 2. It must be insensitive to hydrogen-ion concentration of the pulp; that is, it must froth equally well in an acid or alkaline medium. 3. It must be insensitive to salts, even in high concentration. 4. It must be absolutely noncollecting to both sulfides and nonsulfides. 5. Its frothing properties must not be affected by collecting reagents, including soap, the most generally used nonsulfide collector. 6. It must readily emulsify and disperse any insoluble collecting agent that is likely to be used. Clearly the existing frothers do not qualify. Pine oil, for example, is an acceptable frother for many purposes but if used in soap flotation a delicate balance between pine oil and soap must be struck because, as pointed out by Coghill1, these two reagents are incompatible in certain concentrations. The objections to soap itself as a frother are obvious, and the cresols and their substitution products all have some collecting power and very little emulsifying power. The mechanism of frothing in flotation was early explained on the basis of the Harkins-Langmuir theory of oriented molecules.2 These investigators showed that if an organic compound having an unsym-metrical molecule (in which one end of the molecule contained water-

Jan 1, 1939

By S. Acar, P. Somasundaran

The results obtained for the selective flocculation of natural ores do not usually agree with the corresponding properties of the constituent minerals when present alone. This is mainly due to the presence of dissolved mineral species which can interact in many ways with other components in the system and alter their behavior. In this paper, the effect of dissolved species on the flocculation and electrokinetic properties of sulfide minerals is discussed. Dissolved iron, copper, and nickel (Fe, Cu, and Ni) species are found to affect the properties of natural chalcopyrite and pentlandite in certain pH range. These effects are interpreted in terms of species adsorption leading to activation or depression of reagents, surface precipitation, and complexation of species

Jan 1, 1986

Discussion of the paper of Earl S. Bardwell, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. .1429 to 1441. H. O. HOFMAN, Boston, Mass. (communication to the Secretary*) :-It is pleasing to the originators of the planimetric determination of oxygen in refined copper to see that the method has been taken up by a large smelting plant to be used in every-day work after it has been simplified to suit the new conditions. Several years ago Huntington and Desch 1 had improved our mode of working. They projected the developed negative on to a screen, traced the outlines of the picture with a pencil, drew a border, and measured one constituent with. the planimeter. In order to give the work greater precision, they divided the area into squares of 1 cm. side, shaded the

Jan 11, 1913