Search Documents

By J. Ralph Finlay

In latitude 4" S., about fifty miles from the Pacific, and in the amphitheater on the west flank of the Andes, which is drained by the river Tumbez, is the ancient town and mining district of Zaruma. The town is picturesque in the extreme, perched on a ridge 1800 feet high, between two lovely mountain rivers, looking out upon neighboring hills and valleys clothed in rich green, relieved by many hamlets roofed in red tiles, and, at greater distances on all sides, upon mountain slopes of gloomy forest crowned by the bare summits of the Andes. General Description. The gold-mines, discovered in 1549, mere worked extensively by the Spaniards in the 16th and 17th centuries, until their success was curtailed by the exhaustion of the oxidized surfaceores, and the uncovering of the refractory and hard ores underneath. The industry slowly declined until it was nearly or quite at a standstill in 1878, when an unfortunate English company, organized by Chilian promoters, acquired some of the best properties and began to work them. This company, after an extravagant début, relapsed into a struggle against poverty and mismanagement, and finally collapsed in 1894. In 1896 the English mines and many others, covering most of the district, were acquired by the South American co., formerly the South American Development Co., of New York. (See Figs. 1 and 2.) The vein-formation of Zaruma is extensive and complex, and the ores are somewhat refractory. In the immediate neighborhood of the gold-bearing veins the formation seems to be altogether volcanic, consisting of rather fine-grained holocrystalline diorite; but a few miles away, on either side, some gueisses and crystalline schists are to be found. About four miles south of the mines, and beyond some intervening granites, appear

Jan 1, 1901

By Benjamin Tillson

To MOST mine operators, it seems evident that there is a drill-steel problem, although under certain conditions the amount f drill-steel breakage does not appear serious. What is at fault? It may be one or a combination of circumstances. The development of rock drills to the hammer-drill type in place of the old reciprocating piston drill, probably is one important cause for the greater steel breakage. Perhaps the manufacturers of drill steel have failed to realize what alloys are needed for this new service or have overlooked the changes in the art of rock drilling. Although suitable alloys are provided, they may not be so handled in the manufacturing process as to be in the best condition to withstand the demands of rock drilling. The mine operator may be at fault in desiring to use the smallest possible drill-steel section in order that the gage of the drill bits may be correspondingly small and the amount of footage drilled per unit of labor may be greater; or the black-smithshop practice at the mines may need improvement. The miner who uses the drill steel may also require more intensive supervision and education. Again, the manufacturer of rock drills may have failed to study the types of blows the steel alloys will withstand satisfactorily and which their tools are delivering and so he may not know whether or not a different design of rock drill would equal or excel their present drilling speeds without treating the drill steel so severely. All of these hypotheses probably have their supporters. On the other hand, perhaps we are seeking too much service from drill steel and we need a fuller realization of the fatigue strains developed and should prepare to relieve these by a periodic heat treatment of the steels. However, we do not find any proof that any of these suppositions may be held responsible for the drill-steel breakage attendant to mining. The proposed investigation of this matter by the U. S. Bureau f Mines is fully warranted in the promotion of the conservation of labor and material, and the safety of the workmen. The great range of field conditions, as well as the scope of the research, requires the energetic cooperative support of many interests. Various manufacturers of steel,

Jan 5, 1921

By Alfred W. Gauger, George A. Burrell

The senior author of this paper, while in Colorado on other official business, made a trip to the Cripple Creek gold-mining district to get more data than are at present available regarding the composition of the gas that issues from the rock into the mines of the district. This was done at the suggestion of George S. Rice, Chief Mining Engineer of the Bureau of Mines. There are -many questions of interest and importance in connection with the ventilation of the mines in the Cripple Creek district, such as the menace to life and mining of a suffocating gas entering the mines from the rock, the danger due to powder smoke (from blasting operations), and danger of continued inhalation of rock dust by the miners. This report confines itself to the first problem, the gas from the rock, and principally to one phase of this question, the composition of the gas and its effects on men and lights. A more thorough study of this and other ventilation problems is planned. That the rock gas is a real menace is shown by the fact that miners (variously estimated from 25 to 50 by different persons interviewed) have been killed by it in the 25 years that mining has been vigorously carried on at Cripple Creek. Many men have had narrow escapes from death, some of them having been incapacitated for days. In addition, much loss of time results because at certain periods of the year or on certain days it is impossible to enter some workings. At a few mines, fans force air into the workings, thus supplementing the natural ventilation and much improving conditions, but the improvement is not entirely adequate at all times. Origin of the Gas Lindgren and Ransome1 think that the gas found in the rocks of the Cripple Creek mining district represents the last exhalations of the ex-

Jan 1, 1917

By J. H. Fletcher, S. M. Cassidy

Air has been cooled, heated, washed, humidified and dehumidified for many purposes and in many industries. At a number of metal mines air is conditioned to reduce the high humidity and unbearable heat found in deep workings, and at some mines air is washed to allay siliceous dust. Steam is introduced into the intake air at many coal mines, particularly in winter, for the purpose of keeping loose coal dust so moistened that the hazard of an explosion is lessened. This paper will describe a further successful application of air conditioning in a coal mine, where, for over three years, all intake air has been cooled to a constant temperature for the sole purpose of preventing roof falls. Effect of Warm Weather on Mine Roof It is generally known by mining men that some, if not all, coal mines have more trouble from bad roof during the warm summer months than in winter. Also, it has been observed that roof on intake airways is usually worse than on the return entries, after the air has circulated through the mine. Some mines and some coal seams are much more affected than others. In the Clinton district of Indiana, the No. IV coal seam has a good, firm, gray shale roof except during the summer months, when it deteriorates badly and falls in small slabs 1 to 6 in. thick. Timbering is not very efficacious during this period because in time the roof will shear around the supporting prop or crossbar and either dislodge the timber or leave it supporting only a few inches of crumbly shale (Fig. 1). This action is renewed each summer, choking airways with fallen slate, tearing down trolley wires, hampering haulage, endangering men and adding considerably to the deadwork cost. Only when mines have been worked for a period of years and have been advanced a long distance from the shaft do the active workings become comparatively free of this trouble, and even then the intake entries are still a source of much deadwork. Such was the annoying situation at the mine of the Saxton Coal Mining Co. operated in the No. IV coal just north of Terre Haute, Ind. During the months of warm weather it was possible to stand at any quiet spot in the mine and within 10 min. hear at least two or three falls,

Jan 1, 1931

By Frederick Laist, H. J. Maguire

The ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaccs, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper; this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it mas found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first- and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator produces a product that is self-fluxing; in fact, it is possible to produce a concentrate containing more iron than is necessary to flux the silica. Under these conditions, the amount of basic fluxing materials required for the smelting operations became very srnall and the converter slag lost its former value as a blast-furnace flux. For this reason, a less expensive method of recovering the copper, silver, and gold contained in it than smelting in blast furnaces had to be found. It was not feasible

Jan 1, 1921

By R. C. Thompson

THE lead-zinc mill of Phelps Dodge Corporation, Copper Queen Branch, Mines Division, Bisbee, Arizona, is about 3 miles from the main hoisting shafts of the Junction and Campbell mines at Lowell. All the ore treated in the mill is obtained from these two mines. The mill was designed for an all-flotation treatment of 450 tons of lead-zinc ore per day, and has been operated at that capacity since the start of milling operations on Nov. 17, 1945. An expansion program is underway whereby the mill capacity will be doubled, but this article describes only the original program and presents results of the 45o-ton operation. GENERAL DESCRIPTION The milling plant consists of an ore-receiving bin and three steel-constructed buildings housing, respectively, the primary crushing equipment, the secondary crushing equipment, and the ore-storage bins, grinding, flotation, and filtering equipment. The mill site is the one that was used for a previous copper-concentrating plant, which was operated over a period of years and then dismantled. There remained from this operation some milling equipment, a reservoir for mill-water supply, railroad tracks, tailings-disposal ponds, and a steel-constructed building, all of which were incorporated in the design of the present lead-zinc mill. The location plan of the plant layout is shown in Fig I. The flowsheet of the mill is based on the conventional scheme for lead-zinc treatment, however, several innovations were made necessary in order to utilize the existing building. Placing of equipment also was governed by the design of the building; thus making the mill unique in many respects. The following brief description of the mill building as adapted to the flowsheet points out the compactness of the installation and some of its unusual features. The first floor (Fig 2) houses the grinding equipment, with connecting conveyors for ore feeding, also an air compressor, two vacuum pumps, bins for lead and zinc concentrate storage with individual conveying systems for loading the two kinds of concentrates. Filtering of concentrates is done on the second floor, the concentrates discharging directly into the concentrate-storage bins. On this floor are the lead and zinc filters, two diaphragm pumps, sample-filtering equipment, sample-preparation room and a change room for the mill employees. The flotation machines are on the third floor, at elevations allowing a gravity flow of the lead and zinc concentrates to the thickeners. The annex to the building contains a freight elevator and provides space for all reagent mixing and feeding, also storage of reagents and grinding balls. All the water used for milling purposes is pumped from the Junction mine and

Jan 1, 1947

By C. D. Ramsden

DURING the war years of 1941 to 1945, maintenance of mine locomotives and other mine equipment took the form of rebuilding rather than of renewing. Pur¬chase of new parts became increasingly difficult and mine operators found it necessary to maintain equipment by sal¬vaging old parts. Mine-locomotive wheels, although not representing a high cost per pound of material, contain a con¬siderable amount of steel and without rebuilding would have to be scrapped long before even a moderate percentage of the steel in the wheel is actually consumed. Many mine operators have been re¬building locomotive wheels for several years with automatic open arc-welding equipment. In 1927, the Pittsburgh Coal Co. started such a program, using a single Westinghouse automatic welding head. Since that time, many refinements have been added, until in 1944 the setup was operating very efficiently. A desire to increase wheel life and to hold down rising costs led the company in 1944 to investigate the possibilities of the under¬flux arc-welding process for wheel rebuild¬ing, although at that time, little or no work had been done on multiple pass or "build-up" welding with the underflux arc. Work with this process had been confined largely to welding together flat plates in a "down hand" position. Possibilities for savings were intensified by the fact that the company has 300 locomotives in operation, using actively or as spares 1200 sets of wheels. During 1942 and 1943, about 500 sets of wheels were sent each year to the company's maintenance shop at Library, Pa., for rebuilding. Based on having 800 sets in service (many of the company's heavy locomotives have three- sets of trucks), the average life of a set of wheels was approximately 19 months. Anything that could be done to increase wheel life promised sizable annual savings. OPEN ARC WELDING With the open arc process, a set of wheels could be rebuilt for about 40 pct of the cost of new wheels. Underflux arc welding gave promise of greatly increased welding speeds, more homogeneous, dense deposits and the chance for use of a wider range in welding-wire compositions. Against this was ranged the higher cost of materials and the cost of developing the process from the theory to a practical reality. Since 1927, when a single open arc head was placed in operation, fixed welding procedures had been gradually developed, a positioner for handling a set of wheels was built, and a second head was placed in operation in order to weld two wheels simultaneously. The fixture, or posi¬tioner, which was built to position and turn the wheels under the two welding heads, included a motor drive, controlled by a rheostat, which rotated the wheels through a double set of speed reducers and a removable jaw coupling attached to one end of the axle of the wheel truck.

Jan 1, 1946

By E. W. Davis

The: mysterious Lake Erie price for iron ore, established each spring, determines the maximum price that will be paid during the following season for ore of Mesabi Non-Bessemer base grade. This price is important to the ore producers, hut since most of the ore in the Lake Superior district is owned or controlled by consuming interests, the really important question to them is not the price of ore but how much it will cost them to mine and transport their season's requirements to their furnace plants. However, a few million tons are actually sold each year, and considerable quantities are traded for mixing purposes, and the negotiations lor these sales and trades usually begin with some reference to the Lake Erie price. There is no difficulty with the Lake Erie price itself or with the manner in which it is established, but the system prescribed for determining the values of ores that are not exactly base grade is incomplete. The Lake Erie price takes into consideration only the iron and phosphorus contained in the ore, but when the ore producer is negotiating a sale or trade, he is confronted by the fact that his ore must he studied and the price adjusted, not only on the basis of the iron and phosphorus analyses, as specified by the Lake Erie price, but also on the basis of silica! alumina, manganese, structure, etc. The vague and unsatisfactory methods used in making these adjustments bear some relation to the manner in which the ore is supposed to act in the blast furnace. The ore producer may not understand all of the idiosyncrasies of the blast furnace, but if the smelting-plant operators have a system more accurate than the Lake Erie price method for determining the relative values of different ores, why not pass this information on to the ore producers, so that they can make use of it and perhaps modify their practice in such a manner as to benefit both themselves and their customers? There is a lack of understanding and appreciation between these two groups that may, to some extent, be unavoidable, but in the interests of efficiency and conservation rules that are more accurate and complete than the Lake Erie price method in use at the present time should be established for the guidance of the ore producers. Recently a paper was read before the Eastern States Blast Furnace and Coke Oven Association, by Mr. G. W. Hewitt, Manager Production, Blast Furnace and Coke Oven Department, Wheeling Steel Corporation, in which he explained how his company determines the relative values of different grades of Non-Bessemer ore. This is a very important paper, perhaps not so much on account of the actual calculation methods described as because of the fact that premiums and penalties are shown on Non-Bessemer ores for silica, alumina, phosphorus, and manganese. As pointed out by Mr. Hewitt, the premium and penalty system described may not apply without adjustments to other smelting plants. However, if the various ore

Jan 1, 1941

By E. W. Davis

The: mysterious Lake Erie price for iron ore, established each spring, determines the maximum price that will be paid during the following season for ore of Mesabi Non-Bessemer base grade. This price is important to the ore producers, hut since most of the ore in the Lake Superior district is owned or controlled by consuming interests, the really important question to them is not the price of ore but how much it will cost them to mine and transport their season's requirements to their furnace plants. However, a few million tons are actually sold each year, and considerable quantities are traded for mixing purposes, and the negotiations lor these sales and trades usually begin with some reference to the Lake Erie price. There is no difficulty with the Lake Erie price itself or with the manner in which it is established, but the system prescribed for determining the values of ores that are not exactly base grade is incomplete. The Lake Erie price takes into consideration only the iron and phosphorus contained in the ore, but when the ore producer is negotiating a sale or trade, he is confronted by the fact that his ore must he studied and the price adjusted, not only on the basis of the iron and phosphorus analyses, as specified by the Lake Erie price, but also on the basis of silica! alumina, manganese, structure, etc. The vague and unsatisfactory methods used in making these adjustments bear some relation to the manner in which the ore is supposed to act in the blast furnace. The ore producer may not understand all of the idiosyncrasies of the blast furnace, but if the smelting-plant operators have a system more accurate than the Lake Erie price method for determining the relative values of different ores, why not pass this information on to the ore producers, so that they can make use of it and perhaps modify their practice in such a manner as to benefit both themselves and their customers? There is a lack of understanding and appreciation between these two groups that may, to some extent, be unavoidable, but in the interests of efficiency and conservation rules that are more accurate and complete than the Lake Erie price method in use at the present time should be established for the guidance of the ore producers. Recently a paper was read before the Eastern States Blast Furnace and Coke Oven Association, by Mr. G. W. Hewitt, Manager Production, Blast Furnace and Coke Oven Department, Wheeling Steel Corporation, in which he explained how his company determines the relative values of different grades of Non-Bessemer ore. This is a very important paper, perhaps not so much on account of the actual calculation methods described as because of the fact that premiums and penalties are shown on Non-Bessemer ores for silica, alumina, phosphorus, and manganese. As pointed out by Mr. Hewitt, the premium and penalty system described may not apply without adjustments to other smelting plants. However, if the various ore

Jan 1, 1941

By J. McLaren Forbes

Geologists and engineers in charge of diamond drilling often have no practical experience in the work, yet they must direct the drillers. In discussing some of the problems that arise, the author of this paper has tried to remember the things he did not know about diamond drilling when he first came in contact with that work. The basic reason for most diamond-drill holes is to obtain information. The more thorough the understanding of the geological and engineering problems involved, the greater will be the benefit derived from a drilling program. One of the best methods to ensure some thinking before drilling is to record on the permanent drill log, before the hole is collared, the reasons for the work and the information desired from that particular hole. When the hole is finished, the information obtained should be recorded. Driller The choice of a diamond driller is very important. If no experienced driller is available, a competent miner who has a sense of responsibility and better than average mechanical ingenuity can do the work. The best answer to most practical drilling problems, from the standpoint of the person in charge of the drilling program, is the service of experienced diamond drillers or drilling firms. Equipment Drilling equipment should be adequate to put down the longest hole desired and handle the toughest ground encountered. The type of bit used depends upon the ground drilled. Experimenting with various bits and careful study of footage records are the best means of determining which to use. Under ordinary circumstances it is best to drill using an EX barrel when possible. The length of rod and core barrels that can be used depends on the size of the drill station. Also, the length of core barrel depends on the way the ground cores. In good ground as much core will be recovered with a 10-ft. barrel as with a shorter one, and with considerable saving of drilling time. A water pump is needed if the hole is so deep that the water pressure is not strong enough to wash out the cuttings, or if it is drilled at an angle that prevents full force of the water pressure. Instructions For an Inexperienced Driller 1. Never run a bit too long a time. When a bit seems to be "good for one more run," discard it. 2. Always let the rods down on bottom easily. Protect the bit from sudden shock. 3. Start the drilling slowly and easily. Do not put pressure on the bit too fast. Diamonds can break. 4. Be sure the water pressure is strong enough to clear the bit, but do not use more water than is needed, as it may wash away the core. Usually, if no core is recovered the hole is a total loss. 5. When dry-blocking, do not run without water longer than necessary as the bit may burn. 6. Be sure the rods are well caulked and tightly screwed together. If not well caulked they will lose water, and if not

Jan 1, 1946

INTRODUCTION The after-tax rate of return that properly discounts future cash flows is usually referred to as the "discounted cash flow-rate of return" (DCF-ROR). The method is also referred to as the internal rate of return, true rate of return, and investor's rate of return in some literature. According to Stermole (1974, p. 188) industry polls indicate that the DCF- ROR method is the number one economic evaluation decision method used by more than 90% of the industrial companies that use for- mal economic evaluation procedures. Other economic evaluation methods that have been used in the past, such as payback period, accounting ROR, etc., have largely given way to DCF-ROR analysis because they fail to account properly for the time value of money. DCF-ROR is generally defined as that rate of return that makes the present worth of future generated cash flow over the life of the project (including after tax salvage value) equal to the present worth of all after-tax investments. The "present worthing" of future cash flow involves discounting future cash flow to a present value according to the mathematics of compound interest at some interest rate. The determination of the interest rate that equates the present worth of future after-tax earnings with the present worth of all after-tax investments necessary to create such earnings is properly called the discounted cash flow rate of return analysis. Although present worth calculations are usually used for determining the DCF-ROR, the same results can be obtained by comparing income and costs of any equivalent point in time, i.e., future worth, etc.

Jan 1, 1980

By Christopher G. Atwater

The object of this paper is to describe and discuss the progress that has been made, up to the present date, in the development of the modern by-product coke-oven. There are few members of the Institute who have not heard more or less of the by-product oven-installation, and there are many whose acquaintance with it is intimate and practical. Since the general opinion on the subject has hardly become crystallized as yet, it is hoped that this paper will at least furnish matter for discussion. In order to obtain an idea of the present status of the industry in the principal iron-producing countries, the following table has been prepared : Table Showing Proportion of Coke Made in By-Product Ovens in Various Countries. United Kingdom (1898, Mr. George Beilby). Short Tons. Per Cent. Coal coked in by-product ovens,. .. 1,400,000 7.9 Coal coked in blast-furnaces with by-product recovery,.......2,240,000 12.7 Coal coked in non-by-product ovens,. . 14,000,000 79.4

Jan 1, 1903

SPEAKING generally, it may be said that leaching is the simplest method of recovering copper from its ores. Likewise it is perhaps the oldest method of treatment used by copper metallurgists of the modern era. Reliable records indicate that as early as 1752 cupriferous pyrite was leached in the famous Rio Tinto region in Spain. Though the manipulation was quite different from that in use today at Chuquicamata, New Cornelia, Inspiration, and Andes, it resembled that employed by Phelps Dodge at Bisbee, as described in Chapter XIV. Leaching consists of subjecting ore to the action of a liquid solvent or menstruum (usually an aqueous solution) which dissolves the major part of the soluble copper minerals. The resulting pregnant solution is drained off or otherwise separated from the residual ore; and the copper in the solution is then recovered by some appropriate means of precipitation. When sulphuric acid is the lixiviant, as is usual, the simplest procedure is to pass the copper-bearing solution through large troughs containing scrap iron. The iron displaces the copper in the solution, precipitating it as a slime coating the iron and varying in color -from bright copper to a dull black. This may be washed off at intervals, collected as a sludge, dried, and melted with a little fluxing material to produce reasonably pure copper. Usually, of course, the mud is sent to a smelter where most often its destination is the converter or reverberatory furnace. Modern practice uses precipitation on iron only as a complemental process to electrolytic precipitation or deposition, wherein the pregnant copper-bearing solution, acting as the electrolyte in a cell having insoluble anodes and copper cathodes, is depleted of the copper it contains. Cathode copper, 99.5 per cent pure, is produced ready for the market as refined copper, or for a simple process of melting, fire-refining, and casting in

Jan 1, 1933

By Leslie F. Tedsen, John E. Dorn, Alan E. Flanigan

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By J. B. Austin

IN considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based . upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these effi-ciencies are more useful than others, yet all are instructive; for a knowl-edge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermo-dynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By Yuri D. Tretyakov, Robert A. Rapp

The stoichiometry ranges ofNiOl+y and LiFe,O,-d were established by high-temperatwe electrochemical meas7rements in a stabilized-zirconia electrolyte cell. The results were consistent with doubly ionized cation vacancies in NiO,+y and interstitial lithium or iron ions in . The defect structure of the ternary ferrite was derived from the consideration of equilibration with respect to oxygen between the solid and the gas phase. The absolute magnitudes of defect concentrations were calculated. Pavtial molar enthalpies of oxygen in the compounds were calculated and interpreted in terms of the enthalpy of defect formation in these crystals. NICKEL oxide (NiO,,?) is a metal-deficient, p-type, extrinsic semiconductor whose properties are consistent with a structural model based on the presence of cation vacancies as the predominant ionic defect at sufficiently high temperatures and oxygen activities. A survey of previously reported conductivity studies and the presentation of some more recent conductivity measurements will be given in a later paper.' The absolute magnitude of the equilibrium vacancy concentration in NiO has been reported from combined conductivity and thermogravimetric data of ' However, disagreement exists concerning the state of ionization of the nickel vacancies in NiO. Some authors3-' have proposed that the predominant defects in NiO are singly ionized nickel vacancies and positive holes (h') formed by the reaction where, accorhng to the notation of Kroger and Vink,6'7 Oq represents an oxygen ion on its normal lattice site. Other authors"27E have proposed that doubly ionized nickel vacancies (V{i ) and positive holes are predominant and are formed by the reaction One purpose of the present investigation was to establish the nature of the predominant defect in NiO,+? as well as its equilibrium concentration and thermo-dynamic properties at elevated temperatures and known oxygen activities. To accomplish this purpose, the coulometric titration of oxygen into and out of NiO was accomplished using a galvanic cell involving the calcia-stabilized zirconia electrolyte. The ternary oxide, lithium ferrite (LiFe50,-6) is ferromagnetic and has the inverse spinel structure LiFe,O,-d Thus, in the ideal stoichiometric XY204 lattice, Fe3 ions occupy one-eighth of the tetrahedral (A) sites, and i' and Fe3' ions share at random one-half of the octahedral (B) sites within the fcc sublattice of oxygen ions.g The structure and thermodynamics of the spinel structures have been comprehensively decribed.'-' A recent compilation of literature for lithium ferrite is also available. 15 Oxygen-excess LiFe50sis not expected to exist because both i' and 17e3& ions are in their highest normal valency states (positive hole formation is not favorable). As will be discussed, equilibration of the ferrite crystal with oxygen of a surrounding gaseous phase will result in the introduction of equilibrium concentrations of ionic and electronic defects. In the Results and Discussion section a defect model for LiFe50,-d is proposed. This defect model is tested by high-temperature coulometric titration experiments. EXPERIMENT The oxygen activities in nonstoichiometric NiOl+, (and also LiFe,O,-d) were measured by means of coulometric titration with the high-temperature galvanic cell The critical characteristic of a suitable experimental cell is the complete isolation of the phase to be investigated in a minimum sized chamber which is free from extraneous sources and sinks for oxygen (leakage). Then oxygen is only admitted to the chamber or removed from it in known amounts by coulometric titration, which involves the passage of oxygen ions through the solid electrolyte with electrochemical oxidation and reduction reactions at the platinum contacts to the electrolyte. The experimental cell is shown in Fig. 1. The cap of the cell was the tip from a closed-end alumina tube, which was found to be leak-free from a helium leak-detector test. This alumina cap was about 1.2 cm OD and about 1.5 cm high. A Zircoa calcia-stabilized zirconia tablet (crucible lid) of 1.5 cm diam and 0.3 cm thickness served as the solid electrolyte. A Pyrex ring of about 0.1 cm thickness was placed between the electrolyte and the cap. The electrolyte tablet was painted with platinum paste on the entire outer face and on that part of the inner face which would be within the enclosure; these electrodes were further prepared by heating in air at 1000°C for 2 hr. Nickel oxide powder, listed as 99.999 pct pure, was purchased from Leico Industries, Inc. Pills of the NiO were cold-pressed and sintered at 1050°C for 3 hr in a platinum crucible. This poorly sintered NiO was crushed, and chunks were wrapped in 52-mesh Pt gauze (to catalyze the solid-gas exchange) for place-

Jan 1, 1970

J. T. LITTLETON, JR., ? Corning, N. Y. (written discussion?).-This. discussion will add little that has not been brought out but will show how the problems encountered in the Corning Glass Works were overcome. The chief points of consideration in any equipment are, first, the work the equipment is called upon to do; second, the installation; and, third, the man who will use it. These three points should determine the type of apparatus adopted. If only rough measurements, merely a little better than the eye, are desired, the cost of the instruments should be considered; but if accurate temperature control is necessary, the cost of the equipment deserves only small consideration. There is no question that the real problem for any factory is the installation, making sure that the elements really give the temperatures desired; also, the instruments must be so designed that any man can use them.

Jan 12, 1919

By Hermann Wedding

It is now fourteen years since we German ironmasters, in considerable number, visited the United States on the occasion of the Philadelphia Exposition, and found the iron metallurgy of this country, as must be frankly confessed, in an advanced stage of development not previously suspected by us. At that time the United States already occupied, as now, the second rank, with Germany in the third, the product of pig-iron for that year being, in Great Britain, 6550, in this country, 2093, and in Germany, 1850 kilotons.* This relative position has not been changed. The present annual product of the three countries is, in round numbers, Great Britain, 8380, the United States, 7790, and Germany, 4530 kilotons. But the proportion of the United States, which was, in 1876, but 15 per cent. of the world's product, has now advanced to 30 per cent. When we left America in 1876, it was not only with gratitude for cordial hospitality and for the liberality with which our professional colleagues here had opened to our inspection whatever was worthy of notice in our special field, but also with the conviction that we had collected a great treasure of new and interesting information which we could utilize for the benefit of our German Fatherland. Particularly the achievements of the never-to-be-forgotten Holley in the field of Bessemer practice, set us an inspiring example for imitation in our own country. As an expression of our thanks in more practical fashion, I attempt in this paper to sketch what we have done in Germany since

Jan 1, 1891

By J. L. Wyatt

THE smelting of ilmenite to produce a slag rich in titanium, with pig-iron as a byproduct, introduces new concepts in electric smelting metallurgy. Titanium slags are characterized by low electrical resistance, thereby requiring a different type of electric furnace operation, and power supply sources substantially different from those encountered in normal steel melting and siliceous ore smelting furnaces. This paper describes special apparatus for determining specific electrical resistivity of titanium slags, and reports the values obtained on slags encountered in the process of smelting ilmenite ores. In an induction furnace under conditions approximating normal furnacing operation, 25 general heats and 6 special standardization and comparison heats were run. Results indicate relatively low resistivity. Resistivity depends primarily on slag composition, and, to a lesser degree, on temperature. During the summer of 1947 a cooperative project between the National Lead Co. and the Bureau of Mines was conducted at Boulder City, Nevada, in the Electrometallurgical Laboratories of the Bureau. The project involved smelting of ilmenite ores in electric furnaces, and has been reported in detail.' The author participated as a member of the staff of the National Lead Co. during the entire campaign. One outstanding characteristic of the titaniferous slags, their apparently excellent and variable electrical conductivity, was considered sufficiently important to warrant further study. Although little electric smelting of iron ores has been done in the United States, a certain amount of information is available for comparative purposes. Personal experience in smelting siliceous iron ores in electric furnaces furnished further information for comparison. In general, silicate slags are relatively poor conductors of electricity. Current flow during smelting operations may be maintained through a floating layer of coke on top of the slag bath, or through a bath of molten iron, beneath the slag. Silicate slags are not sufficiently conductive to furnish a path for current passage when normal furnace voltages are used. Experimental smelting of a silicate iron ore was undertaken for comparative purposes. A fluid melt was not obtained until the FeO content was reduced to 15 pct. The resistivity increased as the FeO content decreased, FeO compounds being the most conductive of the various oxides in such a normal slag system. The converse appears to be true in slags containing large percentages of TiO2. It has been found that titanium slags become molten with FeO percentages in excess of 30 pct, and that the conductivity becomes generally better as the FeO con-tent of the slag diminishes. This phenomenon was demonstrated in the furnacing operations at Boulder City. During the initial smelting period furnace electrodes could be held immersed several inches in the slag, with tap selectors set for a no-load voltage of 70 v. As the FeO content decreased, the furnace electrodes would "walk up," until at one point in the process the tips would break the surface and arc on top of the slag. This was undesirable since direct arcing caused losses of important flux additions. The slag compositions under study at that time were such that losses due to surface arcing sometimes caused viscous slags to be formed. Forcing the electrodes into the slag bath by manual control to prevent surface arcing resulted in excessive power input and lack of control. Suitable low voltages were not available. Measurement of the electrical resistivity of titanium slags at various operating temperatures and slag compositions was undertaken. It was believed that this information would be of use in the design of electric furnaces suitable for smelting ilmenite, with voltages, electrode sizes, and electrode spacing adapted specifically to titanium slags.

Jan 1, 1951