Search Documents

By H. Kreye, E. Hornbogen

An increase in electrical resistivity during aging or after quenching from high temperatures is known in a large number of alloys. Plastic deformation of alloys in this condition leads to a decrease in resistivity. This anomaly has been called the K effect. This effect has been reported in Ni-A1 alloys by several authors.'-4 The nickel-rich solid solution y is in equilibrium with Ni,A1 (y') with CkAu structure. With this alloy it is therefore possible to produce a homogeneous solid solution as well as a coherent mixture of y and y. The changes in resistivity should be determined for these two conditions. In the present literature on the K effect no distinction is made between them, because of experimental difficulties to determine small coherent particles. In the present work transmission electron microscopy and image formation by (100) and (110) superlattice reflection of the y' phase was employed for a detailed determination of the temperature dependence of solubility of aluminum in nickel and the resulting microstructures with alloys up to 15 at. pct Al. The solubility line follows the equation indicating a smaller solubility than given in the literature at temperatures below 700°C. X-ray scattering was used to get evidence for short-range ordering in the homogeneous solid solutions.5 Parallel to the determination of the microstructure electrical resistivity was measured as a function of aging tempera- ture, time, and aluminum content, which led to the following results: 1) Resistivity increases slightly during aging of a homogeneous solid solution which was quenched from a high temperature as a consequence of short-range order, Fig. 1, curve c,. 2) Resistivity shows a maximum during aging of all alloys which are heterogeneous according to the phase diagram, but which were obtained as a supersaturated solid solution by quenching, Fig. 1, curve c,. The increase in resistivity is mainly due to coherent precipitation of y'. In Fig. 2 the effects due to short-range order pN and due to precipitation of particles APT are shown for an aging temperature of 450°C and different aluminum contents. 3) The increase in resistivity depends on the size !f the coherent particles. A critical diameter of 15 5A for the maximum was found for all alloys and aging treatments by extrapolating particle sizes determined by electron microscopy. 4) The maximum of resistivity of the heterogeneous conditions does not occur if particles, larger than the critical size, have formed already during quenching. 5) Plastic deformation destroys short-range order as well as small coherent particles. Therefore a decrease in resistivity is observed if the increase in resistivity caused originally by these phenomena is

Jan 1, 1967

Correlation between Metallography and Mechanical Testing By H F MOORE (Henry Marion Howe Memorial Lecture Trans, vol 120 11,000 words ) The lack of effective correlation between metallography and mechanical testing from the days of Reaumur to the present is noted, and two general problems of such cor¬relation are stated (1) the correlation of qualitative test results with quantitative, and (2) the correlation of average results with maximum or minimum results Some correlation has been achieved, notably in the field of heat-treatment and in the study of elastic strength of metals Correlation is in the process of being developed in several other fields, including the quantitative study of the effect of grain size of metal on mechanical properties, of grain size and type of crystalline structure on the sensitivity of metals to weakening at holes, notches and other "stress raisers," and in the study of the starting phases of spreading, "fatigue" cracks Correlation of mechanical test results and metallographic study is needed in the study of such problems as the various theories of failure of metals, the meaning of and tests for service ductility of metals, and the relative damaging effect of defects inherent in metals, such as minute cracks and segregation, as compared with the damaging effect of "imposed" stress raisers, such as screw threads, sharp shoulders, etc The neces¬sity for more correlation of metallography and mechanical testing during student days is emphasized, and also the need of a better understanding on the part of engi¬neers of the significance and limitations of metallographic apparatus and results and of X-ray diffraction This should be matched by a better understanding on the part of metallurgists of the significance and limitations of mechanical tests of metals, of testing machines and strain-measuring apparatus

Jan 1, 1937

By J. L. Jernegan

IN a former paper laid before the Institute, entitled Lead and Silver Smelting in Chicago, I endeavored to give a description of the manner in which argentiferous lead ores from the far West were treated in that city, and also described the method employed in the desilverization of the silver-lead produced from the ores. It will perhaps be remembered, that very siliceous ores, principally from the Emma mine, Utah, containing over 40 per cent. of silicic acid, were then being treated at the works of the Chicago Silver Smelting and Refining Company in the reverberatory furnace, with the use of metallic iron, in the form of borings, as a precipitating medium for the lead ; and that the extraction of the silver from the resulting bullion was effected by the Balbach process. The Swansea Works, also the works at Brighton, just outside of this city, and those of S. P. Lunt, were at that time treating ore of a similar character by the same method. The inadequacy of the process for the ores then under treatment was, in a manner, pointed out by me in the paper above referred to. Since the time of its writing, many and important improvements have been made in the metallurgical treatment of Western ores in Chicago. Most ores are now roasted previous to reduction, and the latter operation is conducted in the shaft-furnace instead of the reverberatory. Such is the fact at least at the Swansea Works, the largest in the city, and here it was where the first steps were taken in this direction. In selecting these works as the subject of this paper, I am in hopes that the description given of the various metallurgical operations, as they are there now conducted, will serve to give an idea of the improvements introduced

Jan 1, 1876

By Sandip K. Mitra, John E. Dorn

The Basinki-modified Seeger equation for deformation of metals by means of thermally activated intersection of dislocations was used to ascertain the various factors responsible for the strain hardening of poly crystalline aluminum and a series of a solid solutions of magnesium in aluminum. The analyses were based principally on the rate of change of strain rate with stress and the Cottrell-Stokes ratio. From measurements of these quantities on a series of strain-hardened states, the force displacement diagram for intersection, the density of dislocations in the entanglements, and the contributions of the athermal local stress and long-range stress interactions were deduced. Poly crystalline aluminum was observed to have the same force-displacement diagram for intersection as single aluminum crystals, and the corresponding diagram for the magnesium alloys differed in a manner that suggested that small amounts of magnesium may decrease slightly the stacking fault energy of aluminum. Although poly crystalline aluminum had about the same initial density of dislocations as the single crystals, the density of dislocations increased much more rapidly with strain in the polycrystals. This factor and the higher back stresses generated in the poly crystalline aluminum were the major factors responsible for the higher strength of the poly crystalline aluminum, As the magnesium content of the alloys was increased, the initial density of the dislocations also increased. Most of the alloy strengthening arose from this factor; alloying effects due to short-range order strengthening, Suzuki locking, Cottrell pinning, and so forth, were estimated to be quite small. The gveater rate of strain hardening in the alloys was deduced to be due primarily to the greater increase in the density of the dislocations with strain as the magnesium content was increased. It is the purpose of the present investigation to shed additional light on the average plastic behavior of a grain in a polycrystalline aggregate, by analyses, based on dislocation theory, of appropriate experimental test results. These deductions when compared with those from single-crystal data will then serve to illustrate the major items of difference between the plastic behavior of single crystals and the average behavior of a grain in a

Jan 1, 1963

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

By David H. Browne

The use of coal-dust fired reverberatory furnaces, or indeed of rever-beratory furnaces of any description, was for the Canadian Copper Co. a matter of necessity, and not of choice. For 20 years smelting had been done in blast furnaces alone, and with the Herreshoff furnaces used prior to 1904 there was no trouble in treating fine ores. But little flue dust was produced, and this, following the time-honored custom, was wetted down and put back with the charge. Whether the flue dust really smelted, or whether it was worn out by being chased around in a circle, was a problem that troubled no one. With the installation of modern blast furnaces and high-pressure blowing engines, in 1904, flue dust commenced to assert itself. Evidently more dust was made than could be smelted, but so many vital. problems engaged our attention at that time that this minor question was pushed to one side. In 1906, the details of blast-furnace smelting and the conversion of matte had been worked out to a satisfactory conclusion, and the ever-increasing piles of flue dust and fine ore on the stock yard demanded serious consideration. Numerous experiments in sintering, briquetting, mixing with converter slag, forming blocks of flue dust with green-ore fines and cement, and so on, were undertaken. None of these showed much promise. Our problem was still further complicated by the question of treating converter slag. The ore was basic, the slag was not needed as a furnace flux, and it was felt that under these conditions the old method of pouring slag in molds and resmelting in the blast furnace was an unnecessary expense. If the converter slag could be settled in basic-lined reverberatory furnaces, in which at the same time flue dust and green-ore fines could be smelted, two problems might thus be solved. Reverberatory practice with our ores was, however, an unknown factor. As carried on in the West, on siliceous ores and concentrates, at least 25 per cent. of fuel was required, and even this ratio depended greatly

Jan 1, 1915

THE CHAIRMAN (H. W. MORSE, Los Angeles, Cal.).-I would like to open this meeting for a little while to the general subject of leaching. We ought not to hold back if we have any new schemes for the future. I know that those of us who are tangled up with this lei thing work will appreciate any suggestions that will make us work harder and, scheme, harder to pull through these past difficulties on leaching. F. S. SCHIMERKA, Clifton, Ariz.-Under the direction of J. W. Bennie, General Manager of the Shannon Copper Co., Clifton, Ariz., 'it has been my valued privilege to cooperate in the elaboration of a hydrometallurgical process aiming at the recovery of copper in mill tailing resulting from a gravity concentration of a low-grade semi-oxidized sulphide ore occurring in a porphyritic gangue. The experimental work which has been carried on with a 25-ton plant is completed, and the company is building at present a leaching plant on a larger scale, the first unit consisting of a 150-ton roasting furnace and accessories for leaching the calcine.

Jan 12, 1916

The age of specialization has made man increasingly dependent on a larger number of different metals and minerals. Overexploitation during World War II and lavish squandering of irreplaceable mineral wealth in the past has resulted in the rapidly approaching exhaustion of some of the major domestic ore sources. History clearly points out that the United States cannot continue to be a world power on an "import to survive" policy. A constructive program of development and appraisal of the nation's mineral wealth, including the planned conservation of her resources, must be adopted. Strictly speaking, conservation of minerals must mean the orderly exploitation of our resources and the prevention of waste in use, with due regard for the future. Real concern for the future may not extend beyond a few generations. Eventually science and invention should take care of the problems arising from shortages of some minerals, and the national defense aspects of domestic deficiencies can be provided for by stock piling and other measures. Early conservationists had this viewpoint; but with a rapidly developing industry and population, a farsighted policy that would deny full realization of immediate ambitions became unpopular. Consequently, the politically minded conservationist broadened the concept to include "prudent use of resources" and brought under the conservation umbrella

Jan 1, 1950

By J. L. Walter

Tungsten ingots with and without small amounts of aluminum, silicon, and potassium were prepared by conventional powder-metallurgy techniques and hot-rolled to 0.001-in.-thick sheet. The ingots were rolled three different ways: I) initially cross-rolled, then straight-rolled; 2) straight-rolled, and 3) straig-ht-rolled, then cross-rolled. Total reductions were 99.8 pct. Samples of the sheet were annealed, in vacuo, at temperatures from 1200" to 2200°C. Substructures and textures were determined by transmission electron microscopy and X-ray diffraction. The doping agents were found to form particles of mullite (Al,Si,O,,) which, on rolling., appear to form strings of particles aligned parallel to the rolling direction. These strings of purticles are associated with an increase in the recrystal-lizution temperature from 1400°C for undoped sheet ThE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of drawn and recrystallized wire.'" The grains generally do not occupy the entire cross section of the wire and have lengths many times the wire diameter. The grain boundaries are, in general, nearly parallel to the wire axis and have long ''fingers" projecting one into the other as may be seen in Fig. 1, a longitudinal section of recrystallized doped wire. When unsuitable additions or no additions are made or the wire is not sufficiently reduced during draw- to 2000°C for doped sheet. The particles also limit lateral grain growth while allowing growth parallel to the rolling direction. This results in the formation by primary re crystallization of large highly elongated grains of specific preferred orientation. The undoped sheet recrystallized to small equiaxed gains. The preferred orientations of the large grains were determined from axis density plots to be (113) (691). (0i3) (362), (116) (304) types for the initially cross-rolled then straight rolled material. These orientations are similar to the orientations of the large elongated grains in doped and heavily drawn tungsten wire. The nucleation of the large grains appears to occur by recovery of certain of the polygonized regions of specific orientation, followed by strain-induced boundary migration.

Jan 1, 1968

By O. F. Thornton, D. L. Marshall

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,' although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.' wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By D. L. Marshall, O. F. Thornton

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,' although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.' wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By T. G. Decker, A. F. Witt, A. M. Gaudin

The historical development of the concept of contact angle hysteresis is reviewed. The measurements of contact angles reported in literature have all been made under static conditions. For the measurement of dynamic advancing and receding contact angles, four methods are described together with an evaluation of their precision. Three of these methods were adapted from devices already used for the measurement of static contact angles. The fourth method uses a new principle and apparatus and is the most accurate. While the relationship between surface tensions and the contact angle was extablished as early as 1805 by T. Young,' it was only in 1890 that the existence of contact angle hysteresis was reported by Lord Rayleigh. His observations, however, remained almost unnoticed. With the invention of froth flotation, the contact angle and its behavior became the subject of investigation. In 1907, L. Sulman and collaborators investigated the cause of discrepancies between recorded values of contact angles. They found that certain variations existed in most cases, but that definite maximum and minimum values of contact angles are obtainable. The difference between the maximum and the minimum contact angle in a given system was termed "hysteresis" by Sulman. First attempts to explain hysteresis were made by E. Edser. In the following years extensive studies of contact angles in various three-phase systems

Jan 1, 1963

By Lincoln F. Elkins, John T. Cooke

Injection of gas to increase oil recovery has been considered for almost all important discoveries during the past ten or fifteen years. However, the number of gas injection projects having sufficient history and data is too limited to permit valid generalities of effectiveness of gas injection. Management and engineers are faced with a difficult problem of selecting those reservoirs which are susceptible to profitable application of gas injection. Injection of gas to maintain high pressure favors some factors affecting reservoir performance such as viscosity, surface tension, and formation volume factor of oil by keeping gas in solution and favors some operating features such as extending flowing life of wells and storing part of the produced gas for future use or sales. Injection of gas at low pressure involves lower compression ratio, or at least a single gas-gathering system, larger displacement volume in the reservoir per unit of gas handled, and permits effective utilization of the naturally existing energy and agent for oil displacement that is gas dissolved in oil. Each program is thus a compromise to meet optimum economic conditions while striving to attain maximum recovery of this important nautral resource. The statement has often been made that pressure maintenance would greatly increase oil recovery by permitting abandonment of formation oil inflated with gas in solution rather than abandonment of the same liquid volume of tank oil, if the same terminal oil saturation could be attained. Simple calculations indicate increases in oil recov- ery as high as one hundred per cent on this basis for high formation volume factor oil encountered in current deep drilling. Important in this statement is "if the same terminal oil saturation could be attained." Implicit in this statement are the requirement of physical

Jan 1, 1949

By John T. Cooke, Lincoln F. Elkins

Injection of gas to increase oil recovery has been considered for almost all important discoveries during the past ten or fifteen years. However, the number of gas injection projects having sufficient history and data is too limited to permit valid generalities of effectiveness of gas injection. Management and engineers are faced with a difficult problem of selecting those reservoirs which are susceptible to profitable application of gas injection. Injection of gas to maintain high pressure favors some factors affecting reservoir performance such as viscosity, surface tension, and formation volume factor of oil by keeping gas in solution and favors some operating features such as extending flowing life of wells and storing part of the produced gas for future use or sales. Injection of gas at low pressure involves lower compression ratio, or at least a single gas-gathering system, larger displacement volume in the reservoir per unit of gas handled, and permits effective utilization of the naturally existing energy and agent for oil displacement that is gas dissolved in oil. Each program is thus a compromise to meet optimum economic conditions while striving to attain maximum recovery of this important nautral resource. The statement has often been made that pressure maintenance would greatly increase oil recovery by permitting abandonment of formation oil inflated with gas in solution rather than abandonment of the same liquid volume of tank oil, if the same terminal oil saturation could be attained. Simple calculations indicate increases in oil recov- ery as high as one hundred per cent on this basis for high formation volume factor oil encountered in current deep drilling. Important in this statement is "if the same terminal oil saturation could be attained." Implicit in this statement are the requirement of physical

Jan 1, 1949

By Paul Beck

IT is well known that the hardness of metallic single crystals, like that of polycrystalline metals, increases during deformation (hardening by cold-work). It is also known that, as a consequence of deformation, the metallic material acquires an evident thermodynamic instability, revealed, for example, by the fact that the increased hardness gradually decreases with time, especially at elevated temperatures (softening by annealing). The temperature at which the stabilizing process begins is different for various metals, and for any metal it depends on the amount of deformation. Such stabilization of deformed metals may proceed in two different ways: through recovery, and through recrystallization. The former process allows the unstable deformed metal body to approach stability gradually and without visible change in the grain structure; the latter process, like an allotropic transformation, yields directly the undeformed stable "phase" in the form of new undeformed crystals, which, starting out of a certain number of nuclei, grow into and' consume' the deformed hard material. The extent of stability attainable through recovery is limited, espe-cially if the deformation of the metal crystal or crystals involves not only the gliding along slip planes, but also the bending of the slip lamellae, or at any rate the bending of comparatively large parts of the crystal lattice. In such cases, for instance in bent single crystals or poly-crystalline metals subjected to any deformation, recovery will not as a rule be able to restore the "straight" undeformed lattice, and stability can be attained only by recrystallization; that is, by the consumption of the bent crystal lattice parts by new, undeformed crystals-a much more drastic process. It is evident that the part of the surplus free energy stored in deformed crystals, which is present in the form of the elastic energy of the bent lamellae, is in these instances not considerably involved

Jan 1, 1937

By Hertha R. Freche

The diffusion of magnesium and silicon from the core into the high-purity coating of Alclad sheet is important commercially, and led to the use of a duplex product for the study of diffusion by means of spectro-graphic analysis of successive layers. It has been found that in the duplex materials the diffusion of magncsium from an undersaturated aluminum-magnesium alloy into its high-purity aluminum coating is approximately of the same order of magnitude as the diffusion of silicon from a saturated aluminum-silicon alloy into its high-purity aluminum coating. However, if magnesium and silicon are both present in the alloy in the ratio of Mg2Si, they appear to diffuse in the approximate ratio of this compound. Finally, if the alloy contains silicon in excess of the amount required by magnesium silicide, the amount of diffused silicon in the high-purity aluminum coating will also be in excess. The interdiffusion of metals in the solid state is of both scientific and technical interest, because it is helpful in the study of the alloy structure and in the solution of problems pertaining to the strength and surface condition of the fabricated product. W. C. Roberts-Austenlt carried out the first quantitative determination of the coefficient of diffusion of gold into lead. This classical experiment was followed by a series of investigations on the diffusion of metals and nonmetals in iron and steel and in nonferrous metals and alloys. Recently the diffusion of copper in coated strong aluminum alloys was investigated by A. Burkhardt2. This appeared to be the first published investigation on the diffusion of metals into aluminum. The present investigation was the direct result of a technical question in connection with alloy fabrication and is a summary of some preliminary work pertaining to the diffusion of magnesium and silicon into aluminum. The results necessarily will be subject to some variations, since this is the first attempt to evaluate the coefficients of diffusion of magnesium and silicon into aluminum according to this method of procedure. This

Jan 1, 1936

By George W. Harris

In the earlier period of anthracite-mining, much coal was wasted, both underground and in the culm-banks on the surface. Such waste is common in the development of new mining-districts, in which, as a rule, only the richest material can be profitably treated. In the anthracite-region, special causes operated to increase this evil. The mines were generally worked under 20-year leases, and royalties were paid upon such coal only as was actually marketed. The lessees consequently cared for immediate profit solely. They were not bound to win all the coal they exposed, or to leave it in such condition that their successors could win it. Nor was it their interest or duty to educate consumers in the use of their product. The market called for coal of large sizes; and such coal they furnished, throwing away the rest. Any pains taken by them to bring about a more rational use of coal by their consumers would have borne fruit, after their leases had expired, to the benefit of somebody else. A full statement of the situation was given in 1893, in the report of the State Commission, appointed in 1889 to investigate the subject.' That body included the names of Heber S. Thompson, William Griffith and the late Eckley B. Coxe.2 Its report gives special attention to the utilization of the old culm-banks.

Jan 1, 1906

By Joseph Hays

MORE years ago than I care to admit I conferred the title of "combustion engineer? upon my-self since nobody else would confer it. I thought at the time, and for some, years thereafter, that my field was limited to the precincts where the fuel was being burned, but I found that I could stand in the door of the furnace room and hear distressed heat units calling for help all over the plant. Some of them were over-worked, others were compelled to do useless work, and still others, anxious to render a proper account of themselves, were not permitted to do any sort of work at all and were utterly wasted. The combustion engineer has something to do at that interesting occasion when the heat unit is being born in the furnace, but his responsibility does not end there. He must follow the little fellow throughout the entire period of its hectic existence in the plant and see that it gets a fair chance and a square deal everywhere. I fear that the general impression of the combustion engineer's duties is much as mine was in the beginning; that his job is limited to the implements and processes incident to the specific operation of converting fuel into active, heat energy and of applying it to the boiler, the still, or what-not, with the least possible waste. But is it not true that a heat unit saved in a remote corner of the plant means just as much to the fuel account as another saved at the furnace? And if nobody else is looking after the heat units out on the range why should the combustion engineer spend all of his time hanging around the corral? If combustion engineer is not a broad enough title to cover the man in charge of a general heat unit rescue campaign call him any-thing else you please. The job is all that counts. The name means nothing. A skunk by any other name would smell as bad. The greatest field I have ever found for general "heat rescue" work is the oil refinery. In refining we first put heat into the oil and then take it away from the vapor. The greatest heat losses occur during the cooling operation, but there are losses, many of them preventable, either wholly or partly, at every step of the several processes in oil refining.

Jan 3, 1928

By O. C. Ralston, William C. Hunter

DUring experimental study on the separation of a zinc concentrate from the heavy sulfide ores of Jerome, Ariz., a great deal of attention has been given to proper activation of the sphalerite content of the ore. The sphalerite at Jerome contains enough iron to class it as a marmatite, as picked specimens have only about 60 per cent. zinc, whereas pure zinc sulfide contains 67 per cent. zinc. This marmatite in large pieces is black in color, but in dry powdered state is brown. A flotation froth made from it has a silvery black luster in comparison with a brassy luster caused by chalcopyrite which occurs in the same ores. The sample used in most of the experiments described below consisted of about 3000 Ib. of diamond-drill core from the zinc-bearing orebodies of the United Verde mine, and had the following analysis: Per Cent. Per Cent. Oz. peR Ton Cu............... 0.695 Al2O3............ 0.83 Ag................. 1.30 Zn............... 6.17 S................ 43.35 Au................ 0.02 Fe...............36.23 CaO............. 0.46 SiO2............. 9.27 Mineralogically, this analysis is calculated to the following, which is in agreement with the microscopic examination: Per Cent. Per Cent. Chalcopyrite................... 2.0 Schist........................... 3.2 Marmatite..................... 10.32 Quartz........................... 8.2 Pyrite........................ 73.0 Calcite.......................... 0.9 All samples were ground in a laboratory ball mill in order to leave about 3 per cent. on a 200-mesh sieve, fine grinding being essential to liberate the minerals in the ore. Most of the Jerome ores are so intimately crystallized that reasonably complete unlocking by grinding does not take place until 800 mesh is approached. Therefore, the 200-mesh grind adopted contains a considerable amount of locked mineral grains, but not so much as to render impossible the preparation of commercial grades of concentrate.

Jan 1, 1930