Search Documents

Jan 1, 1934

By C. H. Mathewson, Kent R. Van Horn

Copper and the copper-base solid solutions readily form twin crystals when plastically deformed at a suitably elevated temperature or annealed after cold deformation. In fact, no feature of the microstructure of these materials is more prominent or characteristic than these straight-sided bands or simple lines of division which sometimes come from groups of thin polysynthetic lamellae, penetrating part way or wholly through the parent grain substance, but often divide the grain into a few or perhaps only two crystallographically related parts. Nearly always the bands as seen in the usual microscopic examination of a specimen come into vivid contrast with the adjacent crystalline material owing to the inherent difference in orientation. Bands which under special conditions of orientation cannot be seen with vertically incident light are often visible under oblique illumination and, when this fails, contrasting effects usually may be obtained by using polarized light. There is no longer any doubt that these synthetic banded structures obtained in the ordinary course of working and annealing are due to twinning of the spinel type which was observed long ago in a number of metals crystallizing in the isometric system.' It has been customary in metallurgical literature to designate these synthetic twins, which grow into prominence during an annealing process, as "annealing twins" without regard to the actual mode of their formation, which is, indeed, obscure and with scant recognition of the fact that prior deformation is essential, no twins having been observed in metal of known unstrained history. This is questionable; especially in view of the fact that in a number of metals and minerals, reorientation into the twin configuration is known to occur as a result of a simple shearing mechanism along the recognized twinning planes and the

Jan 1, 1930

By E. A. Moulder

The mining industry is continually faced with problems involving dewatering, pollution, water supply, leaching and hydrochemical mining and prospecting. Greater application of the principles of ground-water hydrology to solution of these problems promises improved operating efficiency, increased safety and better public relations. Estimating the magnitude of dewatering for a proposed mine may be a major factor in determining the feasibility of proceeding with mine development. Diverting the source of ground water to an abandoned mine may save costly treatment of acid-mine drainage. Development of a large ground-water supply near an ore deposit may enhance the possibilities of a leaching operation. Detection of certain dissolved minerals in water from springs or wells may lead to hitherto unknown mineral deposits. Current efforts of industry, educational institutions and government are making these kind of events more commonplace. Dewatering of Mines The magnitude of dewatering problems was dramatized by a flooding that occurred last year in a gold mine in South Africa. During drilling operations at the West Driefortein mine, a major fracture was encountered from which large volumes of water issued necessitating evacuation of 1350 men from the mine. Dewatering required an increase in pumping of more than 80 million gpd. Models of ground-water systems are being used to test alternate plans for dewatering mines. Using the models in conjunction with computer optimization programs may lead to minimizing costs of operation. In addition to computer simulation of aquifers associated with phosphate deposits in North Carolina mentioned in last year's report, two USGS employees developed a model to estimate the amount of pumping required to dewater a mine site in Colorado.

Jan 1, 1970

By Frank E. Neil, O&apos

The formation tester, as the name implies, is a tool built for testing the contents of sands encountered in drilling Wells Without actually cementing casing on the sand. The tester was developed in the Mid-Continent and has been in use commercially there since about 1926. However, some two dozen patents have been issued on formation testers dating back to the seventies. The method apparently was an outgrowth of the old Mother Hubbard grain or bean packer, used around casing before the days of cementing casing. These packers were also seated in a tapered hole and if the formation tested was not satisfactory the casing was pulled loose and the hole taken down to another formation. A great deal of experimental work has been done in its development, and as a result of this work the formation tester became an accepted integral part of the petroleum development in California. The formation tester was introduced into California some three years ago by M. 0. Johnston. Months of discouraging and expensive work followed its introduction into this state, but one organization after another tried the tool and its use is now fairly general. Shortly after Johnston began testing in California, the Halliburton tester was also introduced into the state and now another tool is being introduced, the Shaffer-Roles tester. Principle and Operation of Testers The principle employed in all formation testers is that of packing off the fluid in the hole above the formation to be tested and thereby prevent,ing it from having access to the testing tool. This permits the fluid contained in the given formation to have unrestricted access to the tool. It is accomplished by running the tool and packer on the bottom of the drill pipe; the valves in the tool being closed while going into the hole to prevent fluid from entering the drill pipe. The packer is then seated at the desired point, trapping the drilling fluid above it. When this has been done, the valves in the tool are opened and the fluid from the formation is allowed to enter the empty pipe through the tool. If the

Jan 1, 1934

By J. A. Eisele, D. J. Bauer, L. E. Schultze

Approximately 100 million mt of magnetic reject tailings, which contain apatite and about 1% yttrium and rare-earth elements, exist in the eastern U.S. as a result of iron ore mining operations. At the present time, no economic process is available for recovering yttrium from this material. The U.S. Bureau of Mines (USBM) studied the problem to determine if an effective low-cost method could be found, thereby increasing our domestic yttrium reserves. [Fig. 1] is a line drawing of a photograph taken during microprobe analysis of a sample of the tailings, and shows the distribution of yttrium. Typical analysis of this material is 0.14% yttrium and 1.1% rare-earth elements (mainly lanthanum through neodymium). Over half of the yttrium is present as a hydrated Ca-Y silicate deposited along interfaces in the grain structure; whereas, the remainder of the rare-earth elements occur as Ca-Fe-RE silicates. The remaining yttrium and rare-earth elements are in solid solution with the

Jan 1, 1977

By Howard L. Hartman

There is reason to believe that ventilation systems so far devised for use with continuous mining machines fall far short of success. This is vividly demonstrated to anyone who has observed in a continuous miner section the localized ignitions of pockets of gas and the generation of dense clouds of dust by the cutting head of the machine. The alarming frequency with which major ignitions and disasters continue to occur in modern mechanical mining and the rise in incidence of pneumoconiosis serve as reminders that our ventilation systems are far from achieving the ultimate in providing protection from either short-term explosions or long- term dust diseases, both of which take lives. Human safety is the main concern in ventilation. But in this day of high-priced labor, let us not forget human comfort, either, for this is a major factor in motivation toward high productivity. The failure or inadequacy of most mine ventilation systems in providing the kind of working conditions at the face that are conducive to productive as well as safe operation is an indictment of our environ- mental control program in mining generally.

Jan 3, 1962

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,400. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service. "It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. Robert Linton is chairman of the Charles F. Rand Foundation Award Committee.

Jan 1, 1944

By AIME AIME

THE non-ferrous alloys have been placed in the same class with steel by metallurgical research on hardening, and hardenable alloys of all metals except zinc are now manufactured. The hardening of the non-ferrous alloys is accomplished by a process of heating, quenching and ageing. R. S. Dean, head of the research department of the Western Electric Co., told of the results of this research in 'a lecture on "Recent Advances in the Art and Science of Fabricating Metals," given before the Missouri Mining and Metallurgical Association on Jan. 24, 1929.

Jan 1, 1929

By AIME AIME

WHEN Russell B. Paul was born in Russell Gulch, Gilpin County, Colorado, that district was the state's leading gold producer. The son of Dr. Henry Paul, who had gone to Colorado from Missouri during the golden era following the Civil War, and had joined the Institute in 1889 when he was manager of the famous Aspen mine, young Paul's early life was steeped in a mining atmosphere from which developed his selection of mining engineering as a profes¬sion. After receiving his E.M. degree from the Colorado School of Mines in 1902, Mr. Paul worked in Colorado and Honduras. Returning from Central America he was married to Mary Ellen Gilmour, daughter of a prominent Central City mining man;

Jan 1, 1943

By Roy L. Zuber

Identification and analysis of mining hazards involves the correlation of accident, injury and illness information from all segments of the mining industry. It would not be feasible to process the volume of data involved without substantial reliance upon a computerized information system similar to that maintained by the Health and Safety Analysis Center. Numerous statistical programs are applied to the computerized accident-injury-illness data base to identify those mining tasks and associated activities which are responsible for most of the injuries and occupational illnesses. These programs are used to flag those mining tasks or conditions at specific mines or segments of the mining industry where either a significant increase in the injury/illness trend has been reported or where the number of injuries/illnesses related to specific mining tasks or conditions are high. Upon identification of those mining hazards which warrant further analysis, a computerized search of the coded accident data is performed to correlate the predominant categories by cause of injury or illness, source of injury, nature of injury, type of accident, etc. From this correlation, those factors most common to the conditions responsible for the hazard may be identified. Based upon analyses of this form, recommendations are made regarding the appropriate engineering, training, and/or operational improvements necessary to alleviate the hazard. In addition to mining hazard analysis, the computerized data base also has application in the area of optimum resource allocation. Computer programs have been developed to assist management in allocating resources based upon organizational requirements and historical accident - injury trends.

Jan 1, 1983

By T. F. Bower, M. C. Flemings

Results are reported of a study of surface dendrilic structure of an Al- Cu alloy solidified against a chill wall. Most primary and secondary "arms " in the surface dendritic structure are arranged orthogonally, giving the impression of strong preferred orientalion on the surface. However, no such preferred orientation exists and it is therefore evident the arms do not represent (100) directions. The primary arms are shown to be interseclions of a (100) plane wilh the chill plane, or, equally often. the projeclion of a (100) direction on the chill plane. Secondary dendrite arms are usually within a few degrees of 90 deg to the primary arm, independent of grain orientalion. Prirary, secondary, and higher-order surface dendrite arms almost always represenl intersections of (100) platzes with the chill surace, or pvojections of (100) direclions. Growlh of secondary arms is favored on the side of the primary arm where a (100) direclion points toward the chill surfAce a1 a Lou, angle. Surface dendrile arms are often observed to be bent. In these cases, the crystal lallice changes orientation; bending is concave to the chill surface. In a previous paper,' a technique was discussed whereby large grains can be obtained at a chill surface. The technique used involves quickly drawing superheated liquid A1-4.5 pct Cu alloy into a thin copper mold, so that the mold is full well before solidification begins. The chill surfaces employed are polished copper blocks coated with amorphous carbon. Shrinkage during solidification between dendrite arms and grains delineates both, without the need for polishing or etching of the cast surface. The grain structure of the chill surface was discussed in a previous paper;' in this paper, the dendrite arms within each grain are examined. Previous work on surface dendrites includes that of Edmunds, who studied the development of preferred orientation in zinc, cadmium, and magnesium.' In zinc and cadmium, he found that the surface region has a (0001) texture (parallel to the chill surface). Walton and Chalmers reasoned that, since the fast growth (1010) directions are in the basal plane, nuclei which have this plane parallel to the mold wall would produce larger grains than nuclei with other orientations. Hence, the texture observed is as expected.3 The same authors, in measurements on aluminum ingots, found no preferred orientation at the mold wall. However, the X-ray technique they used measured the preferred orientation in terms of grain numbers, not grain areas; larger grains were weighted equally with small ones. No preferred orientation is expected on this basis at the chill surface. In a later paper,' Edmunds stated that experiments show a random grain orientation at the surface in die cast aluminum; his technique, also used in his earlier paper, takes account of grain area. Little work has been published on the dendritic structure of metal chill grains. Recent work of Biloni and Chalmers on "predendritic growth" shows the change in morphology from spherical to dendritic during the initial stages of freezing, 5 but this work did not include detailed examination of the fully developed dendrites. Other pertinent work includes that of Lin-denmeyer, who investigated the growth of ice dendrites. 6 When growth was on a substrate, the dendrite axes were bent. The bend corresponded to a change in orientation of the crystal lattice and occurred in such a way as to align the basal plane to the substrate. DENDRITE STRUCTURE Fig. 1 shows the chill surface of a typical casting poured above the critical temperature necessary to produce coarse grains. A cursory examination of these grains shows that the surface dendrite arms within most of the grains are oriented roughly perpendicular to each other. One is tempted to assume that these are (100) directions and that, therefore, marked preferred orientation exists at the chill face. This, however, is not the case. Each of the grains in the casting of Fig. 1 was separately identified, Fig. 2, and its orientation determined by the Laue back-reflect ion method. Results are given in Fig. 3 and it is seen there that no preferred orientation exists. Even when grain area is accounted for, there is no significant preferred orientation. The relationship between surface grain structure and crystal orientation was then obtained by assigning X and Y axes to the casting surface, Fig. 1, and assigning the same axes to the stereographic projections of each grain. Thus, the visible surface structure could be compared readily with grain orientation. This was done for fifty-five of the grains of Fig. 1. Results of this study on three typical grains are described below, and some general observations given subsequently. Fig. 4 shows the structure and stereographic projection of a grain which lies near the (100) zone (with respect to the casting surface). The X and Y directions are marked on the projection, and the photomicrograph mounted with the same orientation. Poles of the stereographic projection represent crys-tallographic directions in the grain which point out of the casting, toward the chill. Two (100) directions are shown in Fig. 4. A line joining the center of the projection and a pole represents the projection of the pole onto the X-Y plane (chill surface). Two such lines are shown in Fig. 4 (solid lines). A line joining the intersection of a great circle with the circumference of the projection gives the trace of a crystallo-graphic plane in the chill surface; two such traces are shown (dashed lines).

Jan 1, 1968

By AIME AIME

WILLIS McGERALD PEIRCE-"Jerry" to his host of friends, and on that account a hit of a puzzle to those who have known him only as "W. 14."-a native of Buffalo, educated at Penn State College, Illinois: and Yale universities, has bee11 associated throughout all of his professional career with the New Jersey Zinc Company. Jerry has served successively as investigator, section chief, and division chief in the research department of the company and has just been promoted to chief of research.

Jan 1, 1937

By Blake M. Caldwell, Thomas C. Poulter

A new approach to an old problem has made it possible to do in a a tively short period what has not been accomplished in the past three quarters of a century using strictly experimental methods. A theoretical study was made of the underlying principles whereby a jet is formed by a shaped charge and of the mechanism of the penetration of the target by that jet. It was found that there are more than 10, and perhaps as many as 15 variables affectin!? the performance of the shaped charge. Only a few calculations are necessary to show that it is physically impossible to investigate all of these variables experimentally. The shaped charge theory has been extended to include a previously little-understood mechanism in high explosive phenomena; namely, low order detonation. By superimposing a high order detonation on a zone already undergoing low order detonation, all appreciable improvement in performance is accomplished. The development of a design wherehy these phenomena are coordinated in such a way as to develop a jet which is tailored to meet the specific target requirement will be described in detail. The shortcomings or even impossibility of strictly experimental techniques will be illustrated by a discussion of the development of a special-purpose explosive charge. INTRODUCTION In an article appearing in the May, 1888 issue of Scribner's Magazine, Charles E. Monroe described his early experiments with gun cotton (Fig. 1) which led to his name being most fre-quently connected with our present-day shaped charge. Although the sunken letters or "cavities" in Mon- roe's gun cotton were not lined, they produced some penetration of an iron plate. The credit for the lined shaped charge, however, should rightfully go to Dr. R. W. Wood of the Physics Dept. of Johns Hopkins University, who was responsible for first discovering the fact that a metal liner in a cavity of explosive gave high velocity fragments and/or jets of metal. This discovery was made by Dr. Wood inadvertently while investigating an accidental death resulting from an electric blasting cap. He discovered that a jet of high velocity copper particles was ejected from the dimple

Jan 1, 1958

By J. R. Low, M. B. Reynolds, L. O. Sullivan

The effect of neutron bombardment upon the stability of type 347 austenitic stainless steel has been investigated by a magnetic technique. The relation of the ferrite content of a stainless steel to its magnetic properties is given, and an apparatus suitable for the measurement of the ferromagnetic saturation induction of small specimens is described. Results of measurements on irradiated specimens are tabulated. Exposure to a neutron flux was found to cause a slight increase in the ferrite content of type 347 stainless steel, the change increasing with increasing length of exposure and with increasing initial ferrite content. The similarity of the effect of irradiation to the effect of annealing is pointed out. Possible effect of irradiation upon density of austenitic stainless steel is discussed. COMMERCIAL austenitic stainless steels are alloys of iron, chromium, and nickel, plus small quantities of other elements. Although these alloys are normally used in the austenitic condition, this state is thermodynamically metastable at ordinary temperatures and transformation to a more stable state takes place under favorable conditions. In the austenitic state, these stainless steels have the face-centered-cubic crystal structure characteristic of y iron, but the stable state at room temperature is a mixture of austenite and body-centered-cubic ferrite. The transformation from the pure austenitic condition may be brought about by cold working the alloy at a temperature below that at which the aus- tenite becomes thermodynamically unstable (about 400°C), the completeness of transformation increasing with increasing severity of cold work and decreasing temperature. The behavior of the austenitic stainless steels under ordinary conditions of use is rather well known. However, use of these alloys in a nuclear reactor introduces a new variable: the effect of neutron bombardment upon the transformation from the austenitic to the ferritic state. It was with this in mind that a study of the radiation stability of austenitic type 347 stainless steel was undertaken. Magnetic Technique for Ferrite Determination Commercial austenitic stainless steels such as type 347 undergo little transformation under normal conditions of fabrication and use. In view of this fact, it seemed likely that neutron irradiation would change the ferrite content of the alloy but little. The method chosen for measurement of the effect of neutron irradiation was thus limited to one which would be quite sensitive to small changes in the ferrite content of the alloy. Of the properties of the stainless steel which can be measured, the magnetic characteristics are most sensitive to the quantity of ferrite present.

Jan 1, 1956

International Trade in Nonmetallic Minerals. BY J W FURNESS AND E W PEHRSON (Man &. Met, Sept, 432 2500 words) International trade in nonmetalic minerals (exclusive of fuels) is dominated largely by fertilizer raw materials such as phosphate rock, potash, nitrates, sulphur and pyrites and the miscellaneous group of minerals including asbestos, mica, graphite, fluorspar and china clay Cost of trans¬portation deters any substantial movement of the building materials which usually occur widely in nature and are thus available near consuming centers at relatively low cost This paper, which presents a summary for 1932 of the world production, consumption and principal trade relations of asbestos, china clay, fluorspar, graphite, gypsum, mica, phosphate rock and potash illustrated by world charts, is based on an original study of 15 nonmetallic minerals conducted by the U S Bureau of Mines Practical and Legal Aspects of Mme Financing See METAL MINING Economic Significance of High-grade Concentrates See MILLING AND CONCENTRATION

Jan 1, 1937

By G. E. Karantzavelos

Anew flotation process to recover alunite from low-grade alunite ores is described. The process begins with run-of-mine ore, reduced to less than 5 mm (0.2 in.), being preconditioned with the reagents before grinding and alunite flotation. From the preconditioning step, ore particles, impregnated with reagents, form pellets that subsequently disintegrate into the pulp during grinding. The second step is basically a standard alunite flotation step. Pilot plant test results show that an alunite concentrate assaying at least 85% alunite and less than 5% silica can be produced. Laboratory and pilot plant results were in excellent agreement, indicating that the new process is a viable means of alunite beneficiation. Plant results, using the new process, were superior to results from conventional alunite flotation procedure.

Jan 1, 1986

By Joseph S. Malesky

As essential as the discovery of coal was to our state of advancement, the discovery and development of explosives marks one of the most important findings in the history of civilization. For this reason explosives are rightfully referred to as the forerunner of progress. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. An explosive may be defined as a substance (usually a mixture) that, where flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1973

By AIME AIME

BY COMBINING the sessions on reduction and refining of copper, lead and zinc it was possible to devote an entire day to nonferrous metallurgy. Four interesting papers were presented at the morning session and four more in the afternoon. In the discussion of papers on copper, F. R. Pyne acted as chairman, with H. M. Shepard as vice-chairman, whereas for those on lead and zinc, F. F. Colcord acted as chairman, with C. R. Hayward as vice-chairman. The paper by P. D. I. Honeyman on the smelting of raw concentrates in the reverberatory furnace was presented by Mr. Pyne and discussed by Messrs. Mazany and Hayward. The interesting paper by E. S. Bardwell, com- paring the use of various fuels in copper-refining furnaces at Great Fails, Mont., was presented by Mr. Shepard and discussed by Messrs. Boggs, Gronningsater and Hayward. That by R. G. Knickerhocker, describing the stationary basic copper converter at Messina, Transvaal, was presented by Mr. Pyne, together with a written discussion by c. R. Kuzell, of the United Verde Copper co. It was an interesting illustration of how well-known processes may sometimes be modified to fit into unusual conditions.

Jan 1, 1932

By M. V. Lowry

This paper outlines the economic considerations that led to the recent installation of a thickener at St. Joseph LeadCo.'s Balmat, N.Y. mill. To incorporate storage of concentrates, they decided upon a single, unusually deep tank to be used for both storage and thickening. The abnormally high rake lift required was achieved by the novel feature of having the entire drive platform raise and lower. Initial operating problems are described along with the satisfactory solutions. Total costs for concentrate handling before and after installation of the storage thickeners are compared. In Northern New York State, the St. Joseph Lead Co. conducts a 2100 tpd zinc mining and milling operation at its Balmat Plant. Conventional crushing, grinding, and flotation is used to produce a zinc concentrate. For 32 years, from 1930 through 1962, the plant operated with the concentrates going directly from flotation to the filtering, drying, and loading facilities. All of the concentrate handling equipment, therefore, had to operate 24 hrs per day. It also had to accommodate wide fluctuations in tonnage, due to variations in the grade of ore. Many problems were thereby encountered in filtering and drying, but it was never concluded that the cost could be justified for installing a conventional, large diameter thickener. Finally, in 1963, they installed an unconventional thickener that is unusual in several respects. The tank depth is 16 ft instead of the normal 8 ft. The rakes are raised and lowered by having the main drive gear located on a movable platform. Automatic controls are programmed to raise the drive platform and rakes during one shift of storage. During the next two shifts of withdrawal, the controls are programmed to lower the drive platform and rakes. After three years of operating this unique storage-thickener, the conclusion is that a correct choice was made from several alternative schemes for storing concentrates. The various considerations involved in the final selection will here be analyzed, and the design features and installation details will be de- scribed. Operating problems and modifications made to the equipment will next be considered, and finally the effects upon filtering, drying, and loading will be reported. SELECTION CONSIDERATIONS Even without a thickener, concentrate handling had become reasonably efficient at the Balmat Mill by the year 1962. A tonnage that varied between 6 and 25 tph was being handled fairly satisfactorily. The filter cake moisture of 8%% seemed quite respectable, except that two large filters were usually in service. Three filters often had to be operated in order to prevent excessive filter overflow with consequent loss of values. This situation occurred when zinc concentrates from flotation exceeded 20 tph and when filter cloth blinding developed. Over the years, numerous small improvements had been effected, such as: selection of a filter cloth with better flow characteristics; addition of flocculant to the filter feed; and, in 1953, the smallest of three drum filters was replaced by a five disc, 8' 10" diam filter with a bottom agitator and snap blow. As another example of fairly efficient operation, the oil-fired dryer was doing a seemingly satisfactory job of further reducing the moisture content to an average of 3%. However, there were often considerable dust losses when the tonnage suddenly dropped off to 6 tph. At high tonnage rates, the resulting high moistures of 4% and 5% caused difficulties due to concentrates sticking and freezing in chutes leading to the box car loaders. (Drying of concentrates is justified because of the high freight rate for the long shipping distance to the company owned smelter at Josephtown, Pa. near Pittsburgh.) It was long realized that installation of a thickener would permit the subsequent steps of concentrate handling to proceed more smoothly and would alleviate the problems existing in the filtering, drying, and loading operations. It was also realized that even a slightly lower filter cake moisture could mean considerable savings in fuel oil. However, all these factors were never quite sufficient to warrant the expense of a thickener until three more considerations were added to the picture. First, the advent of flocculants meant that a thickener of relatively small area could now be considered. Secondly, a complete renovation of the zinc flotation circuit was made between 1957 and 1961. The

Jan 1, 1967

By Cleveland Meeting

Jan 1, 1945