Search Documents

By A. Gatti

A dispersion of AI2O3 was produced within chromium by the hydrogen reduction of a solid solution of Cr2U3-A1203. The yesulting powder. was compacted, extruded, and the material tested in tension at various temperatures and in creep at 1800°F. The material is ductile above 1200°F and is at least twice as strong as electrolytic chvomium at all temperatures. Its creep resistance, rupture strength, and ductility at 1800°F warrant further work to improve its Low -temperatutre properties. BECAUSE of its high melting point and excellent corrosion resistance, chromium has long been considered as a base for high-temperature alloys. Most chromium base alloys, however, are extremely brittle at low temperatures. Elements such as nickel and iron lower the melting point of chromium and thereby limit its high-temperature usefulness. Chromium-alumina materials made by othersl, 2 have shown good high-temperature creep resistance but poor ductility and thermal shock resistance. Pure ductile chromium3 is weak at high temperatures and reverts to a brittle state if exposed to nitrogenous atmospheres. In sintered aluminum powder (SAP)4 and internally oxidized alloys of silver, copper, and nickel, fine dispersions of oxide phases can control hardness, recrystallization, and yield stress. The possibility of formation of a ductile, high-strength material by precipitating dispersions of alumina in a chromium matrix appears worthy of investigation. MATERIAL Powder Production—Chromium oxide and alumina in amounts to produce a final alloy of Cr + 16 pct AI2O3 by weight were colloid milled, filtered, dried and high fired for 16 hr at 1600°C in air. The resulting solid solution of oxides was ball-milled to a fine powder and the chromium oxide reduced to chromium by heating in pure dry hydrogen for 64 hr at 1400°C. Final Materials Produced by Powder Metallurgy Techniques—-Chromium powder, containing a disper-sion of alumina, was pressed into 1 1/8-in. diam slugs at 25 tons per sq in. and sintered 16 hr at 1400° C in pure dry hydrogen. The sintered slugs were encased in a stainless steel can, 2 in. in diam, and extruded at 1200° C through a 1/2-in. die. The 16 to 1 extrusion ratio produced a final chromium-alumina rod 1/4 in. in diam about 30 in. long. Samples of the rod were plunge-ground to small rupture bars of 0.82-in. gage length with a 0.01-sq-in. cross section. RESULTS Microstructure Studies—Fig. 1 is the microstruc-ture of the material in the as-sintered condition while Fig. 2 is the microstructure of the material as-extruded. Comparison of the as-sintered and as-extruded micrographs show the redistribution and realignment of the alumina inclusions by the extrusion

Jan 1, 1961

By V. V. J. Sarma

Interpretation of earth resistivity data involves not only obtaining depth to interfaces but also determining the nature of formations from their resistivity characteristics. Moore's method of interpretation envisages obtaining depths to the interfaces alone. A simple method of estimating the true resistivity values of formations by applying Hummel's formula of average resistivities is proposed. The method would increase the interpretative value of Moore's method as originally proposed. For most of the earth resistivity measurements, the four-electrode configuration developed by Wennerl is employed. In principal, the method consists of energizing (Current I) the ground through two outer electrodes and measuring the resultant potential (v) between the two inner electrodes. The configuration is such that the separation (a) between any two successive electrodes is equal. The apparent resistivity (pa) for such a configuration is given by 2p- a (V/I). By increasing the electrode separation (pa vs a) curves are obtained. Ideally, a homogeneous isotropic formation underground has a characteristic resistivity. However, the field conditions do not present such ideal cases. Almost invariably, even in the same geological bed, the physical conditions are widely different at different parts in the bed. It is further shown that the penetration of the current into the ground for a given horizontal electrode separation, a, is roughly down to a depth, equal to a. It is therefore, evident that the apparent resistivity calculated from the field observations is a weighted average of the resistivities of the materials present down to this depth. With some prior knowledge about the relative dispositions of the geological formations and their physical conditions, it would be possible, by resistivity surveys, to obtain characteristic resistivities for these formations. It is, thus, that the apparent resistivity-electrode separation curves enable one to decipher the resis- tivity distribution at various depth levels and therefore the nature of the geological formations present. Both empirical and theoretical methods have been developed for determining resistivity characteristics of the various formations. The theoretical methods proposed by Tagg2 and Roman3 are derived from studies of the potential distribution on the surface due to the presence of layers of widely differing resistivities underground. The more recent methods of Wetzel and McMurry4 and Wetzel and Mooney5 are but extensions of the original Roman method of superposition. These methods suffer from lack of similarity of the actual field conditions with those of assumed conditions in developing the theory. The empirical methods such as the one developed by Gish and rooneY6 depend purely on personal observation and local peculiarities, and are applicable only for those limited areas. Out of the empirical methods, moore's7 cumulative resistivity method is still found to be applicable in several localities of differing conditions. While Reudy in 1945 adduced some theoretical justification for the method (Eve and Keys),8 Muskat9 and Mooney 10 tried to show the lack of theoretical basis for the same. It is, however, observed that the method in practice "forms a valuable means of successfully attacking the apparent resistivity curves which fail to respond to the Gish-Rooney, the Tagg or the Roman logarithmic methods" (Ramachandra Rao). 11 Comparatively good results are also reported by Melbyel2 by employing Moore's method in interpreting the resistivity results obtained for ground water in the city of Gunnison, Colo. MOORE'S METHOD As has already been pointed out, the application of the theoretical methods is time-consuming, laborious and sometimes not applicable for quick and accurate interpretation of the field data. moore7 has developed a quick method for obtaining depths to interfaces by plotting the cumulative sums of resistivities, against the corresponding electrode separations a instead of plotting the usual Pa — a curve. In this process of continuous integration, corrections for small variations in resistivities, arising due to local surface conditions or adjacent layers, are made, while large consistent variations are brought out

Jan 1, 1963

The industrial might of the Bowen Basin is primarily the result of Utah Development Co.'s work- which has opened up the Blackwater, Goonyella, Peak Downs, and Saraji mines; built the Hay Point port; and is now developing the Norwich Park mine.

Jan 1, 1977

By AIME AIME

Russell B. Paul, Chairman of the Special Committee on Divisional Relationships, presented the interim report of his Committee which was published in the September, 1945, issue of MINING AND METALLURGY and a copy of which is incorporated in the official minutes of this meeting. The following specific actions were taken by the Board of Directors in relation to the six recommendations in the Summary of the Report as published: (1) Mr. Haider, Chairman of the Petroleum Division, presented the formal request of his Executive Committee that the headquarters of the new Secretary of the Petroleum Division be established in Dallas, Texas. After lengthy discussion in which the point was made that the success of this program would depend upon effective co-operation between the Chairman of the Division, the Secretary of the Petroleum Division, and the Secretary of the Institute, the request was approved. The new secretary will be selected by the Division and will be employed by the Institute in the capacity of an Assistant Secretary. (2) The following item in the report was approved:

Jan 1, 1945

By Carl J. McHargue

Rods of 99.99 + pct Al which had initial orientatzons of <001>, <118>, <115>, <111>, and random were swaged at room temperature. Changes in orientation as a function of deformation were studied on axis distribution charts. The <001> orientation appeared to be relatively stable due to the inhomogeneity of the deformation process. near the <100> zone were quickly reoriented towards <001>. Orientations on the <110> zone between <118> and <115> appeared to be stable to reductions of about 50 pct, then were reoriented toward <001>. At very high reductzotzs. movement away from the <111> orientation was observed. the requirement that a circular cross section be maintained. In addition to these mechanical factors, there are grain-boundary effects in poly crystalline materials which are not yet understood. Hartmann and Macherauch conclude, for example, that multiple slip occurs for all orientations in fine-grained aluminum and copper and that the choice of operative slip systems has no simple relationship to orientation.? Many investigators have attempted to avoid problems of interpretation caused by an initial texture by treating the starting material to obtain as ran- IT has been generally accepted that the deformation texture obtained at high reductions, e.g. 90 pct, will not be noticeably affected by a prior texture; whereas, that obtained at reductions of 40 to 50 pct may be significantly influenced by the specimen history.&apos; Some recent studies, however, have been interpreted as showing that an initial texture strongly influenced the deformation textures in rods at reductions greater than 90 pct. Freda and Cullity suggested that the <001> texture in a heavily cold-worked copper rod was due to a <001> texture in the original casting. McHargue, Jetter? and Ogle concluded that the <001> component in an aluminum rod extruded at liquid nitrogen temperature was remanent from a <001> texture in the cast extrusion billet.3 Most of the published work on the effect of initial orientation on deformation textures has been for cold-rolled or compressed single crystals,4-6 The primary interest in these studies was to examine various orientations with regard to their stability under flow? thus determining the possibility of such orientations being stable end orientations. There appears to be no published studies on the effect of initial orientation on fiber textures in polycrystalline specimens. A recent study, however, is concerned with the reorientation of individual grains in polycrystalline specimens pulled in tension.? Although the reorientation of single crystals loaded in simple tension is well known, the movements in the forming of wires and rods would be expected to be different due to the circular array of radial-compressive stresses exerted by the die walls or the rolls, and to

Jan 1, 1962

By K. BRUCE DAVIDSON

-The North Central Texas area includes the following counties in Railroad Commission of Texas District 7-B: Brown, Callahan, Coleman, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Haskell, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, S

Jan 1, 1946

By H. H. Taft

IT has long been known that the volcanic area south of Belmont, Nye county, Nevada, had mining possibilities. Some of the old-time prospectors knew that gold existed there. Its remoteness from any source of supplies, its long distances from water, the absence of game, and more, perhaps, the lack of grass for animals to subsist upon, has made this an unattractive region in which to search for mines. The decline of the Comstock mines, the exhaustion of sun-dry large and rich ore-bodies, the high cost of mining, marketing, and particularly the ruinously high freight-charges upon refractory ore that had to be shipped to distant smelters, have kept investors out of Nevada for the last few years; and mining people have hardly yet awakened to the importance of Tonopah, Goldfield and perhaps the newer and less developed districts. The discovery of Tonopah by J. L. Butler, who located the Mizpah Claim in May, 1900, and the fortunes soon realized there, attracted many people. As the boom declined, many went away, some scattering out into the surrounding country, and the population is now about 7,000. In the fall of 1902 a discovery of gold was made 23 miles south, in what is now known as the Sandstorm group, 4 miles NW. of Goldfield. In the winter of 1903-4 the Combination, January and Florence mines were discovered, and shipments of high-grade ore soon followed. In January, 1905, there were 10,000 people in Goldfield. In June, 1904, rich gold-ore was found 85 miles SE., at the foot of the south end of the Kawich mountains, but this discovery was kept quiet until a re-location could be made. On August 10, 1904, the Bullfrog claims, and a month later the Ladd mountain and neighboring claims, were located. The Shoshone group was located September 24. This district is

Nov 1, 1905

By H. B. Bell, P. C. Lidster

A study has been made of the use of ThO2-Y2O3 solid electrolytes to determine activity of chromium in Fe-Cr and Ni-Cr alloys in the temperature range 1300° to 1700°K. This method has been shown to give results which agree with the best vapor pressure measurements. SEVERAL investigations1"5 have been made of chromium activities in Fe-Cr alloys. Most of these have been made by vapor pressure measurements using knudsen cell techniques while one has been made using gas equilibration with H2/H2O gas mixtures. In the present investigation electromotive force measurements have been made on this system using a thoria yttria solid electrolyte. This system was -chosen to establish the technique of measurement at low oxygen potentials, before extending it to Fe-Ni-Cr alloys. The cell used was Pt Cr • Cr2O3 ilThO2 • Y2O3 llalloy • Cr2O3 IPt Since the oxygen pressure of the chromium-chromic oxide mixture lay in the range 10"19 to 1027 atm in the temperature range investigated, thoria yttria electrolytes were used. It was soon found during the investigation that considerable care was required to prepare satisfactory electrolytes and a study was made to find the best method of preparing pellets of TI1O2-Y2O3 solid solution of as near theoretical density as possible. Various compositions in the range 2 to 15 mole pct Y2O3 were studied but the experimental measurements were made with electrolytes containing 4 to 5 pct Y2O3. The method of preparation finally adopted was to use thorium oxalate and yttria as raw materials. The thorium oxalate was decomposed at 900°C for 6 hr to give a reactive powder. This powder was then mixed with the appropriate amount of yttria and ground in an agate mortar for about 4 hr. The powder was moistened with absolute alcohol as a lubricant and pressed in a metal die at a pressure of 7 tons per sq in. The pellets were then heated at 1100°C for 24 hr followed by 24 hr at 1250°C. After this firing cycle the material was reground and repelleted and again fired at 1100° and 1250°C followed by heating for 7 days at 1600°C. It was found in later experiments that a further firing of 4 hr at 2000°C improved the density further and gave pellets of only 2 pct porosity. After firing, the pellets were polished on emery paper and finally with the 2 µ diamond paste. The polishing was followed by a final firing of 24 hr at 1500°C. Investigation showed that this final treatment minimized reaction between the electrolytes and chromium oxide. It was believed that this was because of a lowering of the surface energy of the electrolyte surface. Two types of investigation were carried out to check that the pellets were satisfactory oxygen ion elec-

Jan 1, 1970

Executive Committee, Board of Directors Augustus B Kinzel, Chairman, J L Glllson, Vice-Chairman, A W Thornton, Howard C Pyle, Grover J Holt Finance Committee, Board of Directors Andrew Fletcher, Chairman, J S Vanick, Gall F Moulton Investments Gail F Moulton, &apos;60, Chairman, Henry Krumb, &apos;59, J Loveloy, &apos;61, C R Dodson, ex off as Treasurer, Andrew Fletcher, ex off as Chairman, Finance Com¬mittee Endowment Andrew Fletcher, Chairman, N G Alford, H DeWitt Smith, W J Coulter, J V N Dorr, R B Gilmore, J B Haffner, O H Johnson, D H McLaughlin, J R McMillan, L F Reinartz, C E Weed, Wilfred Sykes, J R Suman Honorary Memberships H DeWitt Smith, &apos;59, Chairman, C E Reistle, Jr, &apos;59, Grover J Holt, &apos;59, L F Reinartz, &apos;59, M L Haider, &apos;60, D H McLaughlin, &apos;61, John M Lovejoy, &apos;62, Augustus B Kinzel, ex off as President

Jan 1, 1958

By H. l. Burghoff, J. S. Porter

THIS paper presents the results of an investigation of the effect of cold-working and annealing treatments upon the occurrence of preferred orientation in annealed brass wire. The subject has received less consideration than has the same phenomenon in annealed brass sheet or strip, and perhaps very properly so in view of the obvious and undesired results obtained in the forming or drawing of strip having preferred orientation, which results are in contrast with the lack of any spectacular visual evidence in wire. The factors of cold-working and annealing that control preferredness in strip are naturally expected to function similarly in wire. Indeed, one might expect the condition to be commoner in annealed wire, because the severity of the cold-working between anneals in commercial practice is usually much greater for wire than for strip. For example, a wire that is to be finished in the annealed condition on a diameter of 0.040 in. is commonly subjected to a final reduction of 96 per cent between the last two anneals, the large reduction being accomplished in the successive drafts of a multiple-die machine. Wire for rivets, for instance, on 0.125-in. diameter, although given a slight reduction of about 10 per cent after the final anneal, may have been given a prior reduction of 75 to 80 per cent. Barrett1 states the fiber axis of annealed 70-30 brass wire to be [111] with some indication of [100] as a secondary fiber axis. Croft and Sachs2 have reported briefly on some differences in brass wire with random and with preferred orientations. They showed statistical plots of the twin-band angles with respect to the wire axis or direction of drawing as observed on an axial plane. They also pointed out that the resistance of the wire to corrosion-cracking when externally stressed and exposed to a mercurous nitrate solution decreased as the degree of the preferred orientation increased. MATERIAL AND PROCEDURE All the wire for the investigation was processed from one. portion as cut for extrusion from a cast billet of the following analysis: 70.13 per cent copper; 0.01 lead; 0.01 iron; 0.02 nickel; 29.83 zinc (by difference). The billet section, 8 in. in diameter, was extruded hot to 3/4 -in. diameter, after which it was processed by alternate cold-drawing and annealing treatments as indicated in Fig. I. The earliest anneals in process were at about 1100°F. and the next to the last reductions by drawing were 58 per cent. The diameter of the finally annealed wire was 0.132 in. Semifinal anneals were at 800°F., 950°F. and 1100°F. and reductions of 47.5, 74, 83.5 and 89.5 per cent were employed in drawing to 0.132 in. The final anneals were at 875°F., 1050°F. and 1250°F. and were

Jan 1, 1944

By Henry Fay

LAWRENCE ADDICKS, New York, N. Y., (communication to the Secretary *).-There are two points regarding gun erosion on which I want to say a few words: The first is about the analogy to hardening of wire by drawing and the second the possible role played by thermal conductivity of the metal. The ductile metals do not necessarily become brittle when cold-worked as it is possible to draw copper from 3. in. in diameter soft rod down to the finest hair wire without annealing. This results, as stated in the paper, informing a hardened core with a very hard skin. The electrical conductivity is depressed some 3 per cent. and the tensile strength nearly tripled. A soft copper wire 0.08 in. in diameter and 6 in. long may be twisted 150 or more turns before the wire will snap under torsion. A hard-drawn wire will break after perhaps a dozen twists, the skin breaking down at one spot. Just wiping the wire with a cloth clamp with dilute nitric acid has a remarkable effect in increasing the number of twists without appreciably lowering the tensile strength, showing the skin to be very thin. On the other hand, pickling the rod, from which the wire is to be drawn, in dilute nitric acid also greatly increases the number of twists which can be applied to the resulting wire. This indicates that the copper oxide scale produced when the wire bar is rolled hot is more or less rolled into the rod and may have much to do with the skin effect. We also know that if the conditions of drawing are not correct, the heat of deformation in the die may produce quite an annealing effect. The application of this analogy to what occurs in a gun to produce the effects noted offers some difficulty. The second point is that as the temperature of the surface of the gun bore has undoubtedly a great deal to do with the amount of erosion, one natural remedy would be to conduct the heat away fast enough to keep this temperature within desired limits. This brings up the question of the thermal conductivity of the metal of which the gun is made. We know that the conductivity of pure metals is greatly altered by alloying and that the alloy is usually, though not always, lower in conductivity than the metal before alloying. This is interesting when it is considered that the high-nickel and manganese-steel alloys show greater erosion as stated. Would it not be instructive to study the question from the point of view of heat conducted away from the eroded surface?

Jan 3, 1917

By S. A. LoPilato, J. T. Smith

SEVERAL techniques have been evaluated for cooling the throat area of rocket-nozzle inserts to prevent erosion or fracture of the inserts during exposure to high operating temperatures and pressures. Self-cooled composites, such as infiltrated tungsten, have shown considerable promise for these applications. These composites can be fabricated by infiltrating the refractory matrix with a lower-melting metal or non-metal which is insoluable in tungsten. During firing, the lower-melting substance undergoes a series of continuous endothermic phase changes which absorb sufficient heat to maintain the nozzle matrix material at or below a safe operating temperature. At present, the state-of-the-art has reached a point where the refractory matrix density and microstruc-ture have been established as the critical parameters to be controlled for optimum self-cooled performance.&apos;" Nondestructive testing has been utilized to ensure that porous tungsten billets were of uniform density and free from cracks or other defects prior to fabrication into rocket nozzle inserts. Ultrasonic-velocity techniques have been employed because of their reliability and reproducibility. The purpose of this note is to present and interpret the test data developed for porous tungsten matrices. For evaluation purposes, tungsten powders with Fisher subsieve sizes of approximately 4 and 18 p have been obtained for study from four commercial sources: the General Electric Co., Wah Chang Corp., Fansteel Metallurgical Corp., and Kennametal, Inc. Porous tungsten matrices were fabricated from the powders by hot pressing in induction-heated graphite die assemblies. Typical billets ranged from 3 in. diam, 2 in, high to 5 in. diam, 5 in. high. The ultrasonic-velocity measurement technique employed was through transmission, pulse echo at a frequency of 1.0 mc using matched barium titanate crystal transducers. The testing equipment included a pulsed ultrasonic generator, an amplifier, a specimen holder, and an oscilloscope, as shown in Fig. 1. The porous tungsten thickness was measured to i 0.0005 in, with precision micrometers while the oscilloscope achieved 0.02 psec time measurement accuracy. The time for a sound wave to pass through the billet, the bulk wave velocity, was calculated to 0.5 pct using Eq. [l]: V-} where V = bulk wave velocity, in. per psec, T = specimen thickness, in., and / = time, psec. To develop inspection standards, the bulk density of a porous tungsten billet was determined by the ASTM water-immersion technique.3 The ultrasonic-velocity measurements were completed at seventeen positions for each billet and averaged to develop a characteristic standard velocity for a particular tungsten powder at several density levels. A plot of ultrasonic velocity vs density is presented in Fig. 2 for six different tungsten powders. This graph has been established as

Jan 1, 1967

By W. T. Olsen, R. Ulcer

WHEN a liquid alloy freezes, the solid first formed usually differs widely in chemical composition from that last formed, so that there is segregation in the alloy as cast. For example in the copper-nickel system (fig. 1) the first solid formed from a liquid containing 55 atomic pct Cu may contain as little as 38 pct Cu, while the last must contain well over 55 pct. Three factors may act to decrease segregation from the maximum possible. 1. Diffusion in the cooling solid tends to make the phase homogeneous, decreasing segregation. This may be important at slow rates of cooling. 2. Segregation is impossible without diffusion in the liquid. At extremely rapid rates of cooling there may not be enough time to allow maximum segregation. 3. Supercooling delays nucleation to temperatures well below the liquidus thereby decreasing segregation. Hence the first nucleus in the copper-nickel system may contain well over 38 pct Cu. At sufficient supercooling the first nucleus may form below the solidus, in which case there is no reason to expect any segregation whatever. From these considerations, we could predict that at sufficiently low rates of cooling the alloy would be unsegregated because of factor 1 and at sufficiently high rates of cooling there should also be no segregation because of factors 2 and 3. Considerable segregation should occur only at intermediate rates of cooling. We have demonstrated experimentally that segregation can be completely suppressed by rapid rates of cooling. For the alloys studied, however, these rates are too great to be attained in any commercial practice. An alloy of 55 atomic pct Cu, 45 atomic pct Ni was frozen by cooling at varying rates. The degree of segregation in the solid was determined by X-ray diffraction photographs. Slow rates were obtained by slowly cooling the furnace containing the liquid alloy; fast rates by pouring or ejecting droplets of the alloy into water or iced sodium hydroxide solutions. The cooling rate of the droplets can be cal-culated from their dimensions by assuming reason- able values of thermal conductivity.&apos; The experi-ments were repeated with an alloy of 16.5 pct Cu and 83.5 pct Au. A single experiment also showed a 50 atomic pct Bi-Sb alloy had no segregation at the most rapid quench. The position of back-reflection X-ray diffraction lines is a highly sensitive function of the lattice constant, which in turn depends on the chemical composition of the phase. A phase of varying composition will give broad diffraction lines. By measuring the edges of these lines and making suitable corrections for intrinsic line width, it is possible to determine the range of lattice constants represented. These can be converted to chemical compositions from a lattice constant vs. composition curve. Results are shown in table I. In the copper-nickel system the greatest segregation is found at the slowest cooling rates, where the lowest percentage of copper theoretically possible is found. In the copper-gold system, on the other hand, the degree of segregation is decidedly less at the slowest rates of cooling, being greatest at 11,100°C per sec. At no rate is the theoretically lowest percentage of copper (12 pct) found. At the rates of cooling found in sand and die castings the degree of segregation is large and depends little on the rate of cooling. Acknowledgment Most of the material in this paper is abstracted from a thesis presented by William T. Olsen, Jr. in 1948 in partial fulfillment of the requirements for the degree of Master of Science at the University of California.

Jan 1, 1951

By H. W. Gillett

Unlike most previous Howe lecturers, I had not the good fortune to be associated with Henry Marion Howe, nor to be directly one of his students. Yet, through his writings, he has been my teacher, as he has of all American metallurgists. Instructive as his writings are—I use the present tense because Howe thought so keenly and reasoned so surely, seeing clearly, as if by intuition, what was hazy to lesser minds, that his writings are still vital—it is not those books and papers, nor even the minds he trained in his classes, that were his most outstanding service. It was the spirit of Howe in his approach to the problems of metallurgy, his broad-mindedness and fairness, his recognition of the need for theories and hypotheses to explain metallurgical phenomena, his willingness to use them as servants, as well as his questioning attitude—his refusal to accept them as masters—that comprise his greatest service. This most thoroughly warrants the honor the Institute pays each year to his memory. These traits I so respect and honor in any man that I glory in this opportunity to do reverence to him in whom they were so notably united. Howe&apos;s Discussion of a Creep Problem I have often wished that Howe were still with us to turn his keen insight upon the problems of the use of metals at high temperatures, a field much studied but still very hazy. Indeed, 53 years ago, in a paper1 before this Institute, Howe stated a problem closely allied to some that still perplex metallurgists and engineers dealing with the high-temperature field. Howe was intrigued by a report2 from another old master, Robert Henry Thurston, on the behavior of annealed vs. cold-drawn iron wire, and in order to broaden the foundation for metallurgical generalization, Howe made experiments of his own on copper and silver. In these tests by Thurston and by Howe, the wires were rapidly loaded to determine the

Jan 1, 1939

By H. M. St. John

THE melting department is the heart of the foundry. From it clean metal flows to the molding floor, in the right quantity, at the right time and at a sufficiently low cost-or, if not, the foundry fails to thrive. Since it is our purpose here to discuss present-day melting practice in the foundry, it may be well at the start to emphasize the wide differences in foundries and the conditions under which they must operate in order to reach the goal stated in the first paragraph. In every foundry, large or small, jobbing or captive, the same factors must be dealt with but they are of varying consequence and must be dealt with in varying ways in different foundries. Particularly in the nonferrous industry, there is so wide a variation in the composition of alloys used and in the character of castings made that no one type of furnace, nor any one method of operation, can be expected to produce the best results at all times. The present discussion will not attempt to include all nonferrous metals. It is intended to cover only the copper-base alloys in which copper is the dominant element, most of which are commonly known as brass or bronze. The discussion is further limited to the melting of these copper-base alloys for use in sand-casting foundries. Die-casting plants, the brass-rolling mills and certain other metal industries have melting problems peculiar to those industries, which will not be considered here. The following considerations are elemental in all foundries and are listed in what is believed to be the relative order of their present-day importance: I. The melting department must meet the foundry&apos;s requirement for dean, fluid metal, of specified composition and purity, at a temperature suitable for the work the foundry has in hand. This is the prime consideration in any foundry, at any time, anywhere. 2. Working conditions surrounding the melting furnaces and attending their use must be good. 3. The cost of molten metal at the mold must be as low as possible. 4. The operating characteristics of the furnaces must be sufficiently flexible, to meet normal variations in foundry requirements. 5. The operation and maintenance of the melting equipment must not require more skill and experience than is available in the particular foundry in question. METAL QUALITY It is not a function of the melting furnace to refine or improve the quality of the metal but simply to melt it without impairing its quality. Good practice requires, therefore, that care must be taken to supply the melting department with metal of inherently good quality, assured by specification or otherwise, having all the properties necessary to produce the castings desired. An alloy contains a number of primary elements, which must be present in definite proportions if the castings made from it are to have the desired properties. If the castings are made to a customer&apos;s specification, this will state the range within which these principal elements (for example, copper, tin, lead and zinc) are permitted to vary.

Jan 1, 1946

By E. Gybbon Spilsbury

(Pittsburg meeting, March, 1910.) THE recovery of gold and silver from their ores by means of the cyanide process has been so successful in the last few years that any radical improvement would seem impossible; yet the appliance to which I wish to call attention in this paper is really a radical departure from the methods now in general use. The most modern and approved of these, known as the all-sliming method, depends for its success on the grinding of the. ore so fine that practically 90 per cent. of it will pass through a 200-mesh screen. The slimes thus produced are then agitated and aerated in tanks of various types. The main object of this treatment is to insure such a thorough admixture of the pulp and solution that every particle of the ore is surrounded by a volume of solution sufficient to insure the dissolving of the whole of the gold- and silver-content. In addition, in order to expedite the action of the cyanide, and to oxidize such elements as would, if left in their active state, become cyanicides, air is blown in under pressure. In the Pachuca tank, this air is the active and sole means of agitation. The chief objections to all the methods off agitation used heretofore are the expense of operating and maintaining the mechanical devices for keeping the pulp in suspension, and the length of time required to obtain a fairly complete extraction. of the values. These objections are inherent to any method of agitation effecting a circulation of the pulp and the solution together, by giving the whole mass a circular movement, as in the low-tank system, or a vertical circulation, as in the Pachuca-tank system. In both methods, the particles of ore are kept traveling in the same direction as the solution, and with very little difference of speed; so that, while the whole mass is in

May 1, 1910

By John W. Vanderwilt

The unpredictable behavior of ground movement and subsidence has complicated the problems that attend the extraction of large quantities of ore. Special studies, particularly relating to coal mining, have yielded such a voluminous literature and so many involved controversial theories that a partial review would be difficult. Limited space makes any kind of a review impractical. The features to be considered cover only a relatively small part of the broad problems of ground movement and subsidence, but it is believed that this small part is critical. The practical aspects are important, since they bear directly on safety of mine workings, on recovery of ore and on dilution of ore in block caving and related systems for extracting large quantities of rock. The ground movement to be described occurs outside the vertical boundaries of a caved block in the area that is commonly referred to as being in the "zone of draw." "Draw" is a term that originated in the subsidence problems related to coal mining, and it is defined by a line drawn from the margin of the area caved underground to the most distant fracture at surface on the same side of the caved area as shown in Fig. I.&apos; A line thus drawn is called the cave line, and its angle with respect to the horizontal is the cave angle or angle of draw. It is understood that the line is taken normal to the limit of mining, and in a vertical plane. The prevailing theories as to draw and angle of draw assume that appreciable movement occurred along the cave line, which has been described as a fracture resulting from the shearing action brought about by the weight of the overlying load. Fig. 3 shows diagrammatically the mechanics of ground movement adjacent to an area of subsidence according to the prevailing theory of draw (A, from Royce2) and, for comparison, ground movement observed in the Climax mine (B). The text in Peele&apos;s Handbook2 referring to Fig. 2 does not state the meaning of the "original position of top of workable ore" in the rectangular space above "ore in place," and the arrows are not explained. However, this presentation is most concerned with the zones outside the rectangle. According to the prevailing theory, as shown at the extreme left under A, Fig. 2, the vertical tension cracks at surface change at a shallow depth to shear fractures forming the cave line, and it is assumed that appreciable movement takes place along the cave line toward and into the subsiding caved block. The mechanics of ground movement observed in the Climax mine, as shown under B, Fig. 2, does not accord with the prevailing theory, particularly as regards the cave angle and draw. The vertical tension cracks seen at surface die out at depths of 150 to 225 ft. and shear fractures do not develop. Movement is confined at surface to a mantle of rock 50 to roo ft.

Jan 1, 1949

By H. l. Burghoff, J. S. Porter

This paper presents the results of an investigation of the effect of cold-working and annealing treatments upon the occurrence of preferred orientation in annealed brass wire. The subject has received less consideration than has the same phenomenon in annealed brass sheet or strip, and perhaps very properly so in view of the obvious and undesired results obtained in the forming or drawing of strip having preferred orientation, which results are in contrast with the lack of any spectacular visual evidence in wire. The factors of cold-working and annealing that control preferredness in strip are naturally expected to function similarly in wire. Indeed, one might expect the condition to be commoner in annealed wire, because the severity of the cold-working between anneals in commercial Practice is usually much greater for wire than for strip. For example, a wire that is to be finished in the annealed condition on a diameter of 0.040 in. is commonly subjected to a final reduction of 90 per cent between the last two anneals, the large reduction being accomplished in the successive drafts of a multiple-die machine. Wire for rivets, for instance, on 0.125-in. diameter, although given a slight reduction of about Io per cent after the final anneal, may have been given a prior reduction of 75 to 80 per cent. Barrettl states the fiber axis of annealed 70-30 brass wire to be [111], with some indication of [IOO] as a secondary fiber axis. Croft and Sachs2 have reported briefly on some differences in brass wire with random and with preferred orientations. They showed statistical plots of the twin-band angles with respect to the wire axis or direction of drawing as observed on an axial plane. They also pointed out that the resistance of the wire to corrosion-cracking when externally stressed and exposed to a mercurous nitrate solution decreased as the degree of the preferred orientation increased. Material and PRocedure All the wire for the investigation was processed from one portion as cut for extrusion from a cast billet of the following analysis: 70.13 per cent copper; 0.01 lead; 0.01 iron; 0.02, nickel; 29.83 zinc (by difference). The billet section, 8 in, in diameter, was extruded hot to 3/4-in. diameter, after which it was processed by alternate cold-drawing and annealing treatments as indicated in Fig. I. The earliest anneals in process were at about 1100°F. and the next to the last reductions by drawing were 58 per cent. The diameter of the finally annealed wire was 0.132 in. Semifinal anneals were at 800°F., 950°F. and 1100°F. and reductions of 47.5, 74, 83.5 and 89.5 per cent were employed in drawing to 0.132 in. The final anneals were at 87s°F., 1050°F. and 1250°F. and were

Jan 1, 1944

By H. l. Burghoff, J. S. Porter

This paper presents the results of an investigation of the effect of cold-working and annealing treatments upon the occurrence of preferred orientation in annealed brass wire. The subject has received less consideration than has the same phenomenon in annealed brass sheet or strip, and perhaps very properly so in view of the obvious and undesired results obtained in the forming or drawing of strip having preferred orientation, which results are in contrast with the lack of any spectacular visual evidence in wire. The factors of cold-working and annealing that control preferredness in strip are naturally expected to function similarly in wire. Indeed, one might expect the condition to be commoner in annealed wire, because the severity of the cold-working between anneals in commercial Practice is usually much greater for wire than for strip. For example, a wire that is to be finished in the annealed condition on a diameter of 0.040 in. is commonly subjected to a final reduction of 90 per cent between the last two anneals, the large reduction being accomplished in the successive drafts of a multiple-die machine. Wire for rivets, for instance, on 0.125-in. diameter, although given a slight reduction of about Io per cent after the final anneal, may have been given a prior reduction of 75 to 80 per cent. Barrettl states the fiber axis of annealed 70-30 brass wire to be [111], with some indication of [IOO] as a secondary fiber axis. Croft and Sachs2 have reported briefly on some differences in brass wire with random and with preferred orientations. They showed statistical plots of the twin-band angles with respect to the wire axis or direction of drawing as observed on an axial plane. They also pointed out that the resistance of the wire to corrosion-cracking when externally stressed and exposed to a mercurous nitrate solution decreased as the degree of the preferred orientation increased. Material and PRocedure All the wire for the investigation was processed from one portion as cut for extrusion from a cast billet of the following analysis: 70.13 per cent copper; 0.01 lead; 0.01 iron; 0.02, nickel; 29.83 zinc (by difference). The billet section, 8 in, in diameter, was extruded hot to 3/4-in. diameter, after which it was processed by alternate cold-drawing and annealing treatments as indicated in Fig. I. The earliest anneals in process were at about 1100°F. and the next to the last reductions by drawing were 58 per cent. The diameter of the finally annealed wire was 0.132 in. Semifinal anneals were at 800°F., 950°F. and 1100°F. and reductions of 47.5, 74, 83.5 and 89.5 per cent were employed in drawing to 0.132 in. The final anneals were at 87s°F., 1050°F. and 1250°F. and were

Jan 1, 1944

By Kehsin Kuo

DIE steel with 1.47 pct C, 0.42 pct Mn, and 8.22 pct W contains Fe,C and WC in the annealed state and WC embedded in a martensitic matrix in the hardened state (quenched from 800°C). The presence of a large amount of undissolved angular WC carbide particles makes this steel extremely wear-resistant. However, the WC carbide begins to dissolve in the austenite when the heating temperature is raised above 1000°C, but this solution process is still not complete at 1250°C although partial melting has already taken place at the austenite grain boundaries. At 1325 C, this steel contains austenite and liquid metal but no WC carbide, Fig. 1. On quenching into brine, the liquid metal solidifies into a constituent which etches differently from the austenite-martensite matrix. This constituent appears lighter than the matrix at the 1250°C stage when etched with 2 pct nital but darker in Fig. 1 when etched with Murakami&apos;s reagent. Such a constituent has also been found in burnt tungsten high speed steels. This constituent has been isolated from the matrix by anodic dissolution in a 5 pct HC1 electrolyte and was found by the X-ray powder method to be iso-morphous with &manganese, Table I. The agreement in line intensity between these two phases indicates that there is no ordering in this new phase. The calculated cube edge of this phase is 6.395A, somewhat larger than that of ß-manganese (6.30A). Besides this phase, the anodic residue also contains free carbon from the matrix and amorphous WO,, although the X-ray powder pattern of the residue shows the presence of only this phase. This makes it impossible to determine directly the composition of this phase from the residue. Attempts to prepare an alloy containing only this phase have hitherto been fruitless. The following experiments serve to show that this phase can only be obtained by drastic quenching from the liquid state and that its tungsten and carbon contents must be lower than those in the Fe,W,C carbide. On air cooling from 1325oC, the liquid metal solidifies into a eutectic consisting of austenite and the Fe3W3C carbide. The nature of this dark-etching Fe3W3C has also been ascertained by X-rays. This eutectic becomes coarser on furnace cooling. The solidification of a specimen cooled for 5 min from 1325" to 1200°C and water quenched is still not complete and the fine eutectic is formed during the quenching. Since this new phase can be replaced by a eutectic of austenite and the Fe,W,C carbide, its composition must lie somewhere between the latter two phases. The special features of this phase are: 1—it can only form directly from the liquid state by drastic quenching and 2—it is a ternary phase of iron, tungsten, and carbon. The ß-manganese structure of this phase is also interesting. In the Periodic Table, iron and tungsten lie on opposite sides of manganese; a certain combination of these two elements, in the presence of carbon, may have average properties similar to those of manganese. It has already been established that the x phase, a ternary one of iron, chromium, and molybdenum, has the a-manganese structure."&apos; A similar phase has also been found in the ternary system Fe-Cr-W and in the following binary systems: Re-Cb, Re-Ta, Re-Mo, and Re-W.6 References 1 G. D. Preston: Philosovhical Magazine 11928) 5. 7th Series, p. 1207. - K. W. Andres: Nature (1949) 164, p. 1015. 35. G. McMullin, S. F. Reiter, and D. G. Eberling: Trans. ASM 11954) 46, p. 799. &apos; J. S. Kasuer: Acta Metallurgica (19541 2, p. 456. • H. J. Goldschmidt: Trans. ASM (19541 46, p. 807. P. Greenfield and P. A. Beck: Private communication.

Jan 1, 1957