Search Documents

By Robert D. Longyear

IN MOST diamond core drilling the primary objective is the recovery of samples to be used for chemical analysis, physical tests, or visual inspection. Unless these samples are reliable and the information systematically recorded, the time and money spent in securing them are largely wasted. A properly taken diamond-drill sample is similar to a properly moiled channel sample but more accurate. No channel sample can be moiled in as even a groove as the smooth cylinder of material normally removed in diamond drilling. More important still, sampling by the diamond drill practically eliminates that personal equation which Jora1emon4 reference numbers apply to publications listed in the bibliography at the end of this article) has aptly termed "the almost magnetic attraction of the most conscientious hand toward rich pieces of ore."

Jan 1, 1937

By W. F. Wheeler

IN the study of the coals of Illinois now being carried on by the State Geological Survey, an attempt is being made to determine the most satisfactory basis of comparison between different coals. The following discussion is based upon work done for the survey in the laboratories of the State University and under the general direction of Prof. S. W. Parr. " Pure coal " has been defined by Mr. A. Bement1 as ash- and moisture-free coal, and the use of this " pure coal " as a basis for comparing different bituminous coals has lately been much discussed among engineers in the middle West. By some the B.t.u. of the pure coal is being used to check calorimetric results, and to calculate the calorific value of different coal-samples from the same seam, for which purposes it is necessary to assume-first, that the composition and calorific value of pure coal from different parts of the same coal-seam are uniform, and, second, that these values remain constant after the coal is mined, both of which assumptions there are reasons to believe are inconsistent with the facts. Certain variables are included in pure coal, as ordinarily defined, and disregard of them may lead to serious error. In any event, where delicate shades of difference are involved, no sure interpretation of results can be made, unless these variables be eliminated. As a basis of comparison between coals, ash- and moisture-free coal is much to be preferred to " dry coal," and still more is it to be preferred to " moist coal," as ordinarily reported in analyses. There are, however, two constituents other than ash and moisture which are similar in effect to them, and which

Jan 1, 1908

By AIME AIME

T HE Mining Methods Committee held its initial meeting* on Tuesday afternoon, with F. W. Bradley in the chair and W. Y. Westervelt as vice- chairman. The first paper to be presented was "A Plea for a U. S. Court of Patent Appeals," for which Kenneth W. Greenawalt ably pleaded. The paper (which was published in full in last month's issue) is so carefully prepared that no synopsis can do it justice. It discusses the opposed views of some patent lawyers and other lawyers and members of the judiciary as, for example, Chief Justice Taft who is quoted as saying in 1921: "I think it is a great deal better to take a first class lawyer and a first-class judge and make him a good patent expert than it is to take a patent expert and try to make him a first-class lawyer and a good judge." Mr. Greenawalt argued the need for specialized scientific and engineering interest and understanding to enable a lawyer or judge to prepare or interpret patent specifications and decide the originality necessary for a valid invention. He proposed the special U. S. Court of Patent Appeals to also counteract the costly confusion and injustice now ruling where a patent may be declared valid in the courts of certain States and invalid by the courts of other States.

Jan 1, 1930

By J. V. Vogel

Jan 1, 1969

By W. F. Durfee

In the year 1862 the author of this paper was called upon to design and superintend the erection and working of the machinery of an experimental works for the production of steel by a process

Jan 1, 1884

SME Membership Directory Listings of record March 31, 1072 SOCIETY OF MINING ENGINEERS OF AIME

Jan 7, 1972

By C. G. Fink

A PART of the material incorporated in this paper was derived from the studies of ancient metal objects examined by the authors from time to time for museums and art collectors, in order to verify the age of the metal. The data thus accumulated during several years was systemati-cally surveyed and supplemented by new material obtained in examina-tion of a set of specimens that had been generously donated by museums for this study. Altogether over 50 pieces were investigated, of which 39 are described in this paper. Every specimen is at least 1500 years old; the majority are considerably older. Exact conditions to which these bronze and copper objects were exposed in the ground are unknown, unfortunately. It is safe to say that exposure conditions did not remain constant during the long period of burial. Although the collection of specimens studied represents a wide variation in location and age of the objects, as well as in the nature and composition of the metals, it was found that fundamental changes in the metal structure were limited to a few typical cases which, therefore, may be considered as more or less general. The authors' chief aim was to study the effect of extremely long periods of corrosion on the structure of bronze and copper.

Jan 1, 1936

By A. D. Schwope, L. R. Jackson, K. F. Smith

Burghoff and Blank1 have pointed out that the creep properties of hard-drawn coppers are closely associated with their individual softening characteristics and have further shown that the creep resistance of various types of copper is improved, under certain circumstances, by cold stretching. In the design of certain types of electrical machinery, it is important to have the creep resistance as high as possible; furthermore, short-time creep strength is important since in many cases stresses are large only during warming-up and cooling-down periods. In this paper, data are presented showing the effect of cold work on the short time creep strengths of various types of commercial copper under several conditions. It is shown that trends from short-time creep tests are evident at longer times. Materials Used in the Investigation The coppers used in this investigation were commercial grade and of two basic types, oxygen free high conductivity (OFHC) and tough pitch. Additions of silver in amounts of 15 and 25 oz per ton were added to each of the two coppers. The analyses of these six coppers are given in Table 1. Originally, they started as wire bars 4 X 4 X 54 in. A. square rod was made by hot rolling the wire bars to 9/16-in. rod in 8 passes. This rod was then cold drawn to 0.445-in.-diam rod and annealed for 3 1/2 hr at 1000°F. It was then cold drawn to 0.325-in. rod and again annealed at 1000°F for 3 1/2 hr. Hard square rods were then made by cold rolling to 0.257 X 0.257-in. rod. Soft wire was made from the hard- drawn material by annealing at 650°F for 3 hr. The final rolling was performed using a set of 9-in. grooved rolls revolving at 30 rpm, which produced square wires. Reductions of approximately 5, 20, 30, and 40 pct were obtained using several passes in the same direction for the large reductions. The 5 pct reduction by drawing was accomplished using a steel die having 2 parallel bearing surfaces. The die angle was 7 1/2 degrees and the wires were lubricated with a paste of ceresin wax dissolved in carbon tetrachloride. The speed of drawing was 13 fpm. Since work was done on only two sides of the wire simultaneously, it was necessary to rotate it 90 degrees each pass to insure uniform deformation. The room-temperature tensile properties of the various tempers are given in Table 2. The grain size of the an- nealed 0.257-in. wires was uniform and averaged about 0.035-0.045 mm. Experimental Procedures for Short-time Creep Tests Standard creep-test frames (Fig 1) were used for the testing. Special fixtures were designed to apply axial compressive and tensile loads to the copper wires. The compression specimens were 1 in. long and the ends were ground flat and parallel. The creep in compression was indicated by the movement of reference marks s-ratched on intersliding platinum strips attached to the moving heads of the fixture. The movement was measured with an optical micrometer fitted with a filar eyepiece on which the smallest division was 0.00005 in. The tensile creep specirriens were 4 in. long which provided ample gripping surface for the jaw-type grips. The platinum strips were attached to a one-inch gauge length of the wire and the creep measured as previously described. The single-specimen furnaces were connected to individual power and control sources. The controlling equipment consisted of Foxboro controllers

Jan 1, 1950

By J. E. Burke, C. W. Mason

In attempting to study precipitation from a tetragonal lattice, using solid solutione of bismuth in tin, it was found that although a Widmanstätten pattern is observed1,4 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process. Microscopical Studies Alloys were made from Chempur tin (Standard samples 42b and 426, National Bureau of Standards), and bismuth (Kahl-baum C.P.) by melting weighed quantities together under palm oil, stirring well, and castilig in a heated graphite mold. The polishing and etching techniques employed largely govern the visibility of the structural changes. The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through Behr-Manning 3/0 abrasive papers, lubricated by a solution of paraffin in kerosene. A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution; repeated etching and polishing served to remove disturbed metal. For high-power examination better preparation was necessary. It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching. Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use. A better procedure was as follows: The metal lap was warmed slightly, and a 4-in. circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin. The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C. was poured over it, allowed to stand for I to 2 min. and then washed off. It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample. The cloth was then charged with a paste of the relevigated alumina in water. Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet. The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deterioratcs after about 24 hr. This is not serious, because a new lap can be prepared in about 5 min., and only small pieces of cloth are used. Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer. For the final etching, the most satisfactory reagent was that of Tafls,7 the formula for which is: FeC13.6H2O, 2 grams; HC1, 5 c.c.; H2O, 30 c.c.; C2H5OH (95 per cent), 60 C.C. This etchant reveals differences in com-

Jan 1, 1942

By J. E. Burke, C. W. Mason

In attempting to study precipitation from a tetragonal lattice, using solid solutione of bismuth in tin, it was found that although a Widmanstätten pattern is observed1,4 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process. Microscopical Studies Alloys were made from Chempur tin (Standard samples 42b and 426, National Bureau of Standards), and bismuth (Kahl-baum C.P.) by melting weighed quantities together under palm oil, stirring well, and castilig in a heated graphite mold. The polishing and etching techniques employed largely govern the visibility of the structural changes. The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through Behr-Manning 3/0 abrasive papers, lubricated by a solution of paraffin in kerosene. A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution; repeated etching and polishing served to remove disturbed metal. For high-power examination better preparation was necessary. It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching. Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use. A better procedure was as follows: The metal lap was warmed slightly, and a 4-in. circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin. The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C. was poured over it, allowed to stand for I to 2 min. and then washed off. It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample. The cloth was then charged with a paste of the relevigated alumina in water. Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet. The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deterioratcs after about 24 hr. This is not serious, because a new lap can be prepared in about 5 min., and only small pieces of cloth are used. Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer. For the final etching, the most satisfactory reagent was that of Tafls,7 the formula for which is: FeC13.6H2O, 2 grams; HC1, 5 c.c.; H2O, 30 c.c.; C2H5OH (95 per cent), 60 C.C. This etchant reveals differences in com-

Jan 1, 1942

By E. D. Gardner

The Synthetic Liquid Fuels Act (58 Stat., 190; 30 U.S.C. Sup., Secs. 321- 325) was approved by Congress April 5, 1944; it directed the Bureau of Mines to build demonstration plants to produce synthetic liquid fuels from coal, oil shale, and agricultural products. The most important oil-shale de- posits in the United States are in the Green River formation of Colorado, Utah, and Wyoming. The oil shale of western Colorado generally is more amenable to exploitation, more persistent, and apparently richer than elsewhere in the Rocky Mountain Region. It occurs at the top of a high plateau surrounded by bold, nearly vertical escarpments 500 to 600 ft in height. The top 400 to 500 ft of these escarpments comprises an oil-shale measure that averages 15 gal of shale oil per ton; the bottom 70 to 100 ft of the measure, called the Mahogany Ledge, averages over 30 gal per ton. The full measure in a 1000-square-mile area is estimated to contain 300 billion barrels of shale oil;' the Mahogany Ledge is estimated to contain 100 billion barrels of oil. These estimates are based on numerous surface samples and on core-drill holes drilled by the Government and by private enterprise. The oil-shale beds are undisturbed and lie nearly horizontal. The name

Jan 1, 1949

By Albert Hill Fay

IN giving a sketch of the geology and mining of the tin-deposits of Cape Prince of Wales, a short description of the geographic and climatic conditions may be of special interest on account of this being a part of the world of which very little is known, even by the reading public. As shown in Fig. 1, the location of the Cape is lat. N. 65° 35' and long. W. 168°. It is bounded on the north by the Arctic ocean ; on the west by Bering strait and on the south by Bering sea. It is the western-most point of the mainland of North America, and to the west, across the strait, one can see East Cape, Siberia, which consists of a rugged, steep coast of granite cliffs. The climatic conditions are of interest because of the part they have had in the surface geology, and also because they affect mining from an economic standpoint. In connection with the climate and geography, it does not seem out of place here to quote a few lines from the prologue of The Wandering Jew, written by Eugene Sue, under the caption '1 The Land's End of Two Worlds."

Sep 1, 1907

By V. E. Christensen

AT most smelting plants, forced draft, induced by high stacks or fans, is used to carry the gases away from the furnaces, roasters, or sintering plants. Gases moving under forced draft carry varying amounts of solids in the form of dust and fume. Where the weight of the solids is material, and the metal content high, it is usually profitable to treat the gases to recover these solids. Baghouses, Cottrell treaters, and settling chambers are the common forms of plants used to recover solids from gases. To check on the efficiency of these plants it is necessary to know the volume of gas leaving the plant and the amount of solids carried by the gas. As the volume of gas is equal to the product of the velocity of that gas and the cross-sectional area of the flue, the determination of the volume includes the measurement of the area of the cross section and the determination of the velocity. The velocity is generally measured by means of the Pitot tube and Ellison differential pressure gage, although low velocities are best determined by means of an anemometer. The dust concentration is determined by passing a measured volume of sample through a filter and weighing the dust caught. From this the dust concentration per unit of volume may be calculated. It is necessary to assume that the gas is homogeneous or that each cubic foot of the gas contains the same weight of dust as every other cubic foot. Having the volume of gas passing through a flue per unit of time, and the dust concentration of the gas per unit of volume, the amount of solids may easily be calculated.

Jan 1, 1935

By Floyd Kelley

THE literature of the last decade is rich with information relating to the cause and means of control of grain growth in pure metals, but is deficient concerning the role diffusion plays in grain growth, although during this period many new products that depend on diffusion for their properties and success have been developed. Among these are cementation products, produced by calorizing, chromizing, and carbonizing, or by mixing, pressing, and sintering powdered metals such as Syke's iron-molybdenum die material, Genelite, and Elcon Metal (copper, tungsten) etc. This is a fertile field for new developments, but before it can be util-ized to the fullest extent there must be a thorough investigation of the processes by which diffusion and grain growth take place. Grain growth plays no small part in the process and certainly the physical properties of these products depend largely on the grain size and state of equilibrium produced. The field of investigation does not end here, but may be extended to the effect of diffusion on impurities, segregations and dendrites in the broad field of ferrous and non-ferrous metallurgy. A number of years ago the author investigated several of these cases and noted, with striking regularity, the pronounced effect of diffusion in promoting recrystallization and grain growth. An example of this phenomenon is given in his paper on chromizing1 which contained photomicrographs of large radial or columnar crystals produced by diffusion of chromium in the solid state. Another manifestation of this effect was discussed by Austen,2 who showed the part hydrogen plays in the decarburization of steel and the effect of diffusion upon the grain structure.

Jan 1, 1928

By Henry Mulryan

DIATOMS are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skeletons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of varying thicknesses. DIATOMITES Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition. DIATOMS More than 8000 species of diatoms have been named and classified. Some are definitely classified as to their habitat; some are so well recognized as to their living conditions that they can be stated to be diagnostic types, and when encountered in a deposit determine the origin of the deposit. Some of the commoner types of diatoms found in the fresh-water diatomites on the Pacific Coast are: [Cymbella lanceolata Agardh Fragilaria virescens Ralfs Encyonema prostratum Ralf s Diatoma vulgare Bory Surirella biseriata Brebison Eunotia major Ehrenberg Amphipleura pellucida Kutaing Stictodiscus niagarae Ehrenberg Gomphonema geminatum Lynberg Melosira granulata Ehrenberg]

Jan 1, 1939

Prof. Henry S. Jacoby, Cornell University,Ithaca, N.Y. (communication to the Secretary): When a simple beam supports any given load, the lower fibers me in tension while the upper fibers are in compression, and if its cross-section is rectangular the neutral surface, where the stresses pass through zero from tension to compression, is at mid-depth, provided the elastic limit is not exceeded. In addition to the longitudinal stresses, there are horizontal shearing-stresses between the fibers which have their maximum value in the neutral surface, and which equal zero at the upper and lower surfaces, while there are also vertical shearing-stresses. Let another beam of the same dimensions be placed on top of this one, and the load be doubled, it then produces stresses in each beam of the same character, magnitude and distribution as in the preceding case, provided there be no friction between the adjacent surfaces of the beams. Next let these two beams be so firmly united that there will be no motion between them when the same load is again applied. All the fibers in the upper beam are now in compression, and those in the lower beam in tension, while the maximum stresses in the outer fibers are only one-half as large as before. The strength of the combined beams is therefore doubled. If, however, some motion occurs between the beams, then the stresses in some of the lower fibers of the upper beam pass from compression to tension, and those in some of the upper fibers of the lower beam from tension to compression, while the stresses in the outer fibers have a magnitude between the two values previously stated. These fundamental facts relating to the flexure of beams indicate the necessity of carefully designing the keys or brace-

Jan 1, 1898

By J. D. Hanawalt, W. H. Gross

Magnesium has long been known as the lightest of our engineering metals. This metal, silvery white in color, has a specific gravity of only 1.74. Aluminum, the next lightest structural metal, is 1 ½ times heavier; zinc is 4 times heavier; iron and steel are 4 ½ times heavier; and copper and nickel are 5 times heavier. Magnesium does not occur in the free state but is very abundant in nature, constituting 2.5 pct of the earth's crust in the form of various ores. It is the third most abundant structural metal, being exceeded only by iron and aluminum. Magnesium is unique, however, in that in the form of magnesium chloride it also exists in the oceans. Sea water is the source most widely used for production in the United States but magnesium is also commercially produced from magnesite, dolomite, and other ores as well as from certain inland brines. The vast quantity of magnesium existing in the waters of the oceans can be visualized when it is realized that the removal of one hundred million tons per year (the approximate annual steel production in the United States) for a million years would reduce the magnesium content of sea water only from 0.13 to 0.12 pct, providing no more magnesium had washed into the sea in the meantime. Not only is magnesium potentially very abundant but it is in addition a very versatile metal and can be shaped and worked by practically all methods known to the art of metal working. It can be cast by sand, die, and the various permanent-mold methods;

Jan 1, 1953

By Jerry Tien

Mine regulators are normally used for proper air distribution in underground mines. They are deliberately introduced resistance in the regulated airway, and by altering sizes, they can distribute specific air quantities to regulated splits and free splits (4, 5). The enactment of the Federal Coal Mine Health and Safety Act of 1969, the Federal Mine Safety and Health Amendments Act of 1977, and the regulations adopted by the Mining Enforcement and Safety Administration (now called the Mining Safety and Health ministration) prompted greater discussions of optimal mine regulator locations because of the Act's stringent ventilation requirements (2, 3). For example, by requiring the separation of the air used in the belt haulage entries from the intake and return airways, the regulations required the creation of a third type of airway---the neutral airway, as opposed to the intake and return airways, adding to the complexity of a mine's ventilation network. It is the intent of this report to show that panel regulators should be located in intake airways at the neck of a panel for a blowing fan system and in return airways at the neck of a panel for an exhausting fan system in order to achieve optimal air control. A computer simulation model is used to determine optimal mine regulator location.

Jan 1, 1983

By Robert F. Mehl

Jan 1, 1944

By Robert F. Mehl

Jan 1, 1944