Search Documents

By Dever Ashmead

ANTHRACITE was first mined in the Wyoming Valley and sold as an article of commerce in 1808. As some preparation has always been necessary to make it ready to burn, the preparation of anthracite must date back over a hundred years. Two vital factors have determined to a large extent the degree and method of anthracite preparation. These are, first, the character of the beds worked and the methods by which they were mined and, second, the equipment used and practices followed in the burning of the coal. It is not the intention here to go deeply into these phases of preparation as a paper of no mean length could be prepared on the history of either. Rather, the intention here is to point out the main considerations and to show the influence they have exerted on the preparation of anthracite. MINING METHODS AND THEIR RELATION TO PREPARATION In the beginning f the nineteenth century, the coal beds were virgin with the possible exception of some outcroppings that had been worked, to a slight extent, by the Indians. It is known that the American aborigines had a knowledge of the use of this fuel, because when the Wyoming Valley was purchased from them, in 1754, they mentioned the fact that, by selling the land, they would lose their coal.

Jan 9, 1921

By J. M. GLEDHILL

(Washington Meeting, May, 1905.) A Discussion of Mr. J. M. Gledhill's paper, read by title at the Lake Superior meeting, but presented first at the New Yolk meeting of the Iron and Steel Institute (October, 1904), and here published under a mutual agreement. Between the two Institutes. Discussion. MR. E: WINDSOR RICHARDS, Past-President, said that at a recent meeting of the Institution of Mechanical Engineers a paper was read on tool steel, and he called the attention of the members to the high-speed tool steel at the Bethlehem Works. They would have the pleasure of seeing those wonderful works and would see 60, 70, 80 and 100 tons oil lathe with half-a-dozen of these high-speed tools running. PROP. H. M. HOWE (Columbia University) said that they all looked upon these high-speed tool steels as of very great importance, particularly to the machine shop. One point occurred to hire : Had it really been shown that Swedish steel is necessary, or better than equally pure steel that is not Swedish; and is cemented steel really necessary, and is there any advantage in using that, rather than equally pure open-hearth steel'! It might be well if the author could indicate the kind of evidence on which lie bases his assertion that it is necessary to have cemented Swedish steel. Many were hoping for the development of high-speed steels from elements which exist in great quantities, such as silicon, manganese and chromium, rather than from rarer metals like molybdenum, vanadium and tungsten, the supply of which is likely to be soon exhausted. If the high-cutting speed was to last more than a generation, it. seemed to him that they would have to draw upon the common ele¬ments and not upon the rare ones. MR. Tom WESTGARTH (Middlesbrough) said he fully appreci¬ated what had been said about the advantages of using high-speed steel, because great benefit had been derived from the

Mar 1, 1905

By Kenneth A. Gutschick, Robert S. Boynton

Lime has become a general and loosely used term to denote almost any kind of calcareous material or finely divided form of limestone or dolomite, as well as burned forms of lime. However, according to Webster, lime is only calcined limestone (known as quicklime, unslaked lime, or calcium oxide). It also embraces the secondary product of quicklime, i.e., hydrated lime or slaked lime (calcium hydroxide). There are two basic types of limestone used for lime manufacture-high calcium and high magnesium (dolomitic). The dolomitic quicklimes and hydrated limes correspond to their "high calcium" counterparts. The only difference is that the dolomitic types are a combination of the elements calcium and magnesium, in varying percents, whereas high calicum limes contain less than 5% MgO down to 1/2%. In either case a pure form of limestone of at least 97% combined carbonate content is needed to make salable lime, barring a few exceptions. The calcination of both types is diagrammed chemically as follows: [ ] In the foregoing reversible reactions the limestone is burned (calcined) in lime kilns, with the carbon dioxide content of the stone expelled as a gas. The weight loss during calcination of pure high calcium limestone is 44%; with equimolecular dolomitic limestone, the weight loss is 48%. Since lime has a strong affinity for CO_, particularly if moisture is present, it will readily revert to its original carbonate form. This occurs when quicklime "air-slakes" and adsorbs CO.. from the air. Thus, quicklime is perishable and should be stored in dry, water-tight areas. Depending upon the type of kiln used and the physical structure of the stone, the size of the quicklime may range from sandlike granules to 8 in. lumps. However, pebble sizes ranging from 1/4 in. to 2 in. are the most common. Screened quicklime fines are also com¬pressed (pelletized) into 1 in. pellets. For some purposes ground or pulverized forms of quicklime are used, ranging from No. 10 mesh to dust. Generally a pebble of quicklime is about the same size as the pebble of limestone before calcination (perhaps shrinking slightly). A more stable form of lime is hydrated lime. This is obtained by adding water to quicklime, slaking it into a dry, fine, subsieve size white powder. Because its affinity for moisture has been satisfied, it is not vulnerable to further moisture like quicklime. However, it has the same strong affinity for CO_. The following reversible chemical reactions illustrate how hydrated lime when heated (or dehydrated) can revert to the original oxide form:

Jan 1, 1975

By AIME AIME

T HE Board of Directors of the A. I. M. E. held a meeting at Institute headquarters on Jan. 28, 1921. There were present 10 directors and 14 guests, the secretary and the assistant secretary. The following actions of the Executive and Finance Committees were approved: Wilkes-Barre Meeting, Sept. 12 to 17, 1921; authorization of Oregon Section; authorization of Upper Peninsula Section; appointment of Philip W. Henry and Thomas H. Leggett on special committee on Code of Ethics; and presentation of five copies of Raymond Memorial Volume to T. A. Rickard, who edited it. The By-Laws of the Ohio Section were approved. The resolutions in reference to the payment of certain contributions and assessments to the Library Board of the United Engineering Societies, adopted by the Board of Directors on June 27, 1919, were rescinded, and the resolution adopted that the income of the James Douglas Trust of $100,000 be paid over to the Library or otherwise applied by it for the purpose of maintaining the Scientific Library of this Institute in such manner as may be deemed advisable in furtherance of the purposes of such trust, and that said income shall be paid on account of and included in. the assessment levied by the United Engineering Societies on the Institute for the maintenance of the joint libraries of the Founder Societies.

Jan 1, 1921

A. Blainey (Ministry of Supply, Atomic Energy Research Establishment. Hnrtoell. England)—With ref- erence to the published work of Hausner et al. on the powder metallurgy of zirconium, it will be of interest to summarize briefly the results of preliminary work we have carried out on this subject at A.E.R.E., Harwell. For the early experiments we used zirconium

Jan 1, 1953

By Robert Archer

IT is now well known that the structure of aluminum-silicon alloys can be refined in a rather remarkable manner, with consequent improvement of physical properties, by certain treatments applied to the molten metal shortly before casting. The differences between the treated and the untreated alloys are so marked that special terms are used to distinguish them, the untreated alloys being referred to as "normal" and the treated alloys as "modified." The first practical method of accomplishing this result was that of A. Pacz,1 which consists in treating the molten metal with a, salt flux of which the, active ingredient is sodium fluoride. The result can also be brought about, and in a more economical manner, by the addition of small quantities of metallic sodium (or potassium) to the molten alloy shortly before casting.2 The action of the Pacz flux evidently consists essentially in the production of free sodium by the reaction of sodium fluoride with aluminum. The changing of a normal alloy to a modified alloy is referred to as "modification' and any process for accomplishing this result is a "modifying" process. Modified aluminum-silicon alloys were introduced several years ago, and it has been demonstrated both in the laboratory and in commercial practice that it is no simple matter to produce castings having the maximum or nearly the maximum properties which under favorable circumstances can be obtained. The alloys are rather sensitive to small changes in chemical composition, and the modifying process must be carried out in a very particular manner to obtain the best results. Extensive experimental work has been carried out in the laboratories of the Aluminum Company of America with the object of determining the conditions that must be observed to make these alloys of the greatest possible

Jan 2, 1926

By ALFRED D. FLIWN

ENGINEERING COUNCIL is not "about to die," as some persons are saying. Through a natural and foreseen reorganization, Council is entering a new stage of existence with enlarged power for usefulness. Its early constituents have made it possible for many more of their fellow engineers and men of other technical vocations -to take a- share in its activities, responsibilities and support. A new organization is being set up, but it is really a new embodiment of the same spirit of service. Another step is being taken toward the full acceptance by the technical professions of their obligation to the public and to one another for those services which can -be rendered only through effective organization. A brief retrospect is timely. Engineering Council was established in the spring of 1917, as a department of United Engineering Society in response to requests of its Founder Societies. .It followed various attempts of these societies to deal through joint committees with public questions affect¬ing engineers -and with inter-society affairs. These attempts had very limited results. In the new by-laws adopted by United Engineering Society, the purposes and-powers d-powers of Engineering Council were thus defined: "To provide for convenient cooperation between the four Founder Societies, for the proper consideration of questions- of general interest to engineers and to the public, and to provide the means for united , action upon questions of common-concern to engineers.

Jan 1, 1920

By Joklik, G. F.

Most publicity about the copper industry nowadays is focused on the adequacy of ore reserves and on excessive mining capacity. These concerns, stemming from public awareness of actual and potential shortages and oversupplies, relate to production rather than consumption. Perhaps the reason for this one-sided view is that copper is thought of as a commodity which is conspicuously traded in world markets, rather than as one of many industrial materials that serve today's rapidly changing technology. Copper differs from other widely traded commodities in that its real cost of production has progressively increased since World War 11. The reasons for the increase are identifiable by analyzing operations in one of the world's large producing centres, the copper province of Arizona. Another respect in which copper differs from some other commodities is that increases in demand occur less automatically in the case of copper than they tend to in commodities whose consumption is more directly related to population growth. The copper industry's current inability to generate and attract needed investment capital is attributable to these differences between copper and other commodities; it suggests that the concept of copper purely as a commodity is outdated. The key to the problem is better integration between the activities of copper producers and users. Depending on circumstances, integration takes various forms- for example, investment tied to long-term sales con- tracts between producers in developing countries and consumers overseas; common ownership of producing and manufacturing facilities in industrialized nations like the U.S.; and consumer-oriented research and marketing by the copper producers.

Jan 1, 1978

By F. T. Havard

(Canal Zone meeting, November, 1910.) I. INTRODUCTION. THE present truce in litigation between Western smelting and ranching interests gives opportunity for a summary of the results achieved by metallurgists in condensing fume and de-acidifying furnace-gases. In the absence of complete records of past experiments, there has been a good deal of unnecessary duplication of attempts and' failures. Yet, especially under the recent policy of our large corporations, looking to the economic recovery of the values of by- and waste products, original and, in some cases, effective measures have been developed by American metallurgists. In the case of Bliss vs. the Anaconda Copper Mining Co., the Montana Supreme Court, recognizing the progressive efforts made to render the flue-gases innocuous, and the value to the community of the smelting company's operations, refused to hamper its work, and returned a verdict in favor of the defendant. In the trial, the experimental firms of the company in the so-called "affected region" were proved to be thriving perfectly, showing that immunity was guaranteed to vegetation and stock by the wide distribution of the sulphurous acid gas in the dry air of Montana. Indeed, L. S. Austin has proved that by the time the fume is 4,000 ft.. distant from the stack, the percentage of sulphurous acid has been diminished from 2.28 to 0.00045; and Angus Smith has shown that rain must contain 40 parts per million of free acid before vegetation is affected. The arsenic in the stack-gases is but a very small part of the original content of the ore, of which 80 per cent. and over is rejected in the concentrator and furnace waste-products or recovered in the flues. Nevertheless, neither the peace in Montana nor the armistice

Aug 1, 1910

Last October a committee was appointed by The War Service Association of Manufacturers of Solder and Bearing Metals, Inc. to consider the report of the U. S. Bureau of Standards to the Conservation Division of the War Industries Board, a letter of the War Industries Board, and the discussions of this letter as reported at the meetings of association and to summarize the information thus obtained. The report of this committee has just been printed. The committee agrees with the Bureau of Standards that 99 per cent. tin can be used. It also finds that a very small amount of lead might increase the tendency of the bearing to crack and that lead has a hardening effect on babbitts up to a possible limit of 10 per cent. of lead. Still in the so-called genuine babbitts, in the presence of lead a certain proportion of low melting point eutectic is introduced which admits of the bearing being poured into thinner sections and is decidedly advantageous in the die-casting process in producing a much smoother casting. But the committee recommends that the Bureau of Standards thoroughly investigate this point. Lead-base babbitts, to give satisfactory service, must be carefully made of the proper raw materials. The bronze hearing that has been thoroughly tinned and containing the thinnest possible babbitt lining is now becoming recognized as the ideal bearing. The compositions, recommended by the committee are as follows:

Jan 2, 1919

By C. Dinis da Gama

In mining, all unit operations are closely interrelated, and the results of blasting are probably the key factor within that sequence. The drilling program prior to blasting is just as dependent upon the desired rock fragmentation as are the loading, hauling, and mechanical crushing operations which are economically and technically influenced by the results of blasting, namely, the size and scatter of the product. What is known today as optimum blasting is the process of designing a blast in order to obtain a certain degree of fragmentation so that overall mining costs are minimized. Applying this criterion often results in a different program than when an individual blasting pattern is chosen only on the basis of the lowest operational cost for that pattern, disregarding what comes before or after the blast. [Fig. 1] shows the characteristic variation of mining unit costs with the degree of fragmentation, or the maximum size of blocks obtained from blasting. From the figure, it can be seen that optimum breakage must correspond to the lowest total costs, but reducing drilling-blasting costs only does not achieve such an optimum solution. Methods of designing surface or underground blasting operations should comply with the optimization criterion, but this compliance is feasible only if a detailed mining system analysis is available. Therefore, predictions of costs of loading, transporting, and mechanical breakage of ore as a function of its size will define a narrow range of variation for drilling and blasting parameters in order to get the minimum total costs.

Jan 1, 1972

By G. P. Marino

The "conductivity ", Kr, of a spherical void in a linear temperature gradient due to radiation is calculated by integration of the general expression for diffuse radiation between two gray surfaces of arbitrary orientation. The spherical geometry allows an exact evaluation of the phenomenon without resorting to up-proximate expressions for the radiant heat flux. The resulting expression for Kr is three quarters of the approximate value obtained by Loeb. IN the determination of the thermal conductivity of porous materials such as sintered UO2 and ThO2 fuel pellets, the magnitude of the thermal conductivity in the pores due to radiative heat transfer across the pore, Kr, may be important in assessing the total conductivity of the pellets. Loeb' has calculated Kr for various pore geometries by approximating the net flux of heat between two surfaces of temperature difference AT as 4eT~AT and obtained: K,=4yoet3odp [1] where a is the Stefan-Boltzmann constant, E is the emissivity of the radiating surface, To is the average absolute temperature of the region across which radiation occurs, dp is the largest dimension of the gap in the direction of heat flow, and y is a geometric factor. That is: y = 1 for laminar pores and cylindrical pores with axes parallel to the heat flow direction, y = 2/3 for spherical pores, y = /4 for cylindrical pores with axes perpendicular to heat flow direction. It was the purpose of this work to obtain an exact expression for K, in spherical pores by integration of the general expression for the net heat transfer between two incremental areas on the surface of a spherical pore. This procedure yields a value of Kr 3/4 of that obtained by Loeb. I) CALCULATION OF Kr Fig. 1 illustrates the general geometry which defines the problem. The total emissive power for a gray body is given by: E = EoT4 [2] where E is the radiated energy per unit area of the radiation surface per unit time, T is the absolute temperature, o is the Stefan-Boltzmann constant (o = 5.67 X lo- '' watt per sq cm-"K1), and E is the emissivity of the surface. Although Eq. [2] gives the exact expression for the total emissive power of any gray body, all practical problems involve the net exchange of thermal radiation between a body and surrounding bodies. The two major considerations in the solution of such problems are a) shape and relative position of the surfaces and b) the emissivities of the surfaces. In this work it shall be assumed that all incremental areas on a pore have the same emissivity and, further, that little or no reflection occurs (i.e., the radiation hitting a surface is either absorbed or transmitted). Thus, the solution of the stated problem requires only that consideration a be satisfied. Consider two incremental surface areas dA 1 and dA2 of the same material in a general orientation to one another. Let dAl be at temperature TI and dAz be at T2. Fig. 2 illustrates the geometrical parameters involved. That is, 71, is the normal of dA, n2 the normal of dA2, r the line connecting the centers of each area, 81 the angle between nl and r, and Q2 the angle between 7,2 and r. Using Eq. [2] and the Lambert cosine law of diffuse radiation it is easily shown that:293 WdAf- dA, = ecr T*------^fpi------" dAidA2 [ 3a 1 and

Jan 1, 1970

By Samuel S. Wyer

THE following description of methods for conducting gas-producer tests is probably the first attempt to give the subject an analytical, thorough and comprehensive treatment. In some cases where tests have been made, the methods have been so unsystematic and ambiguous that it has been impossible to secure comparable results. To eliminate this difficulty, the following provisional code of gas-producer tests-which has some resemblance to the code of boiler-trials of the American Society of Mechanical Engineers-has been developed. The primary object in testing a gas-producer is to determine whether the producer is working satisfactorily or, what is the same. thing, to see if the efficiency is as high as it should be with the type of producer in question, and also to find out if the composition of the resulting gas is adapted to the work it has to do. In order that the test shall be of any value, it must be thorough and comprehensive, and must be conducted with skill and care. When so conducted, the test will reveal the economy of the producer; and, by making suitable changes, the efficiency will often be increased very much. As a result of the tests made by Jenkins, 1 the efficiency was raised from 56.2 to 71.2 per cent. This shows the large saving that may frequently be made in the fuel-consumption by studying the results of a careful test.. The log of the test, given in Fig. 1, shows that, just as soon as the temperature became regular, the percentage of CO, decreased and that of CO increased.

Mar 1, 1905

By AIME AIME

BLANDFORD. C. BURGESS, the new Chairman of the Industrial Minerals Division, took the advice of Horace Greeley in reverse-he turned his hack on San Francisco and the Golden Gate, and after a few side excursions toward Alaska and Arizona, hit the trail eastward, not for the lonesome pine, but for Spruce Pine, N. C. Born Aug. 10, 1893, in San Francisco. Burgess found his first job, shortly after finishing high school at 19, as axeman for a surveying party of engineers working for the Southern Pacific Co. in Oregon. Later he moved on up with them into Alaska. He liked the engineering profession, and decided to equip himself further so he entered the University of California in the fall of 1913. and for the next two years devoted himself to acquiring an education in civil engineering.

Jan 1, 1945

MINING ENGINEERING presents the annual membership report of the Society of Mining Engineers; see page 147.

Jan 7, 1964

By AIME AIME

C. H. BENEDICT, chief metallurgist of the Calumet and Hecla Consolidated Copper Co., has pioneered for nearly half a century. Noted for his ammonia leaching process, lie has Iong been responsible for all Calumet and Hecla mill, concentrator, and reclaination plant flowsheets. His influence has spread far beyond his own organization. lie is dean of Lake Superior metallurgists and has contributed greatly toward raising his specialty-the country over-to an honored profession; not merely an honored profession but a profitable one for industry and the public. The leaching process which he developed in 1912 has, since 1915, produced for Calumet and Hecla 250,000 tons of copper from waste tailings at a cost per pound, in 1929, below five cents. It has yielded profits of $35,000,000. In the war just ended, this process proved the only one adaptable to the recovery of copper from gilding-metal¬clad steel strip, and Calumet and Hecla treated more than 50,000 tons of such scrap for the Government.

Jan 1, 1945

By MAURICE ALTMAYER

M Y DUTIES, as a member of the Department of Franco-American War Cooperation of the French High Commission were to study the copper and brass industries of America from the mining of the various non-ferrous metals to the semi-finished, or finished materials. In the pursuit of these studies, it was my privilege to visit a number of industries and organizations in different parts of the country. I first visited most of the Eastern copper refineries that were supplying the Allies with vast amounts of metal. These works are producing their material by the multiple or the series process, although the first method predominates. But, regardless of the process employed all the plants attain an exceptionally high standard of quality in their production. One of the points that particularly attracted attention was the manner in which improvements could be traced from the older worlds to the more recent ones. The impression was that, thanks to a spirit of broad-minded cooperation between the principals of the companies and frequent exchanges of views between members of the staffs, all persons interested benefitted by the experience thus gained, to the advantage of the community at large.

Jan 1, 1920

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemisorption.

Jan 1, 1950

By T. Egleston

THE works of the Ore Knob Copper Company are situated in the county of Ashe in the northwestern part of the State of North Carolina, about ten miles from the Virginia line, at an elevation of 4600 feet above the sea. The nearest railroad station is at Marion, Smythe County, Virginia, about forty-five miles distant. The roads from the railroad to the works have been constructed by the company for the transportation of their material, and are very hilly, and in certain seasons of the year in bad repair. Transportation is therefore always limited and never easy, although it is done by contract at a very low price. The main difficulty with the transportation is not so much its cost as the fact that it puts a limit to the production of the works. These unfavorable conditions make it necessary for the owners of the mine to smelt their ores and to send to market nothing except the metal, which alone will bear the cost of transportation. The mine was opened previous to 1860, but has only been worked systematically during the last five or six years. The vein is a fissure vein from ten to twenty feet in thickness in the gneiss of the

Jan 1, 1882

By T. Egleston

The works of the Ore Knob Copper Company are situated in the county of Ashe in the northwestern part of the State of North Carolina, about ten miles from the Virginia line, at an elevation of 4600 feet above the sea. The nearest railroad station is at Marion, Smythe County, Virginia, about forty-five miles distant. The roads from the railroad to the works have been constructed by the company for the transportation of their material, and are very hilly, and in certain seasons of the year in bad repair. Transportation is therefore always limited and never easy, although it is done by contract at a very low price. The main difficulty with the transportation is not so much its cost as the fact that it puts a limit to the production of the works. These unfavorable conditions make it necessary for the owners of the mine to smelt their ores and to send to market nothing except the metal, which alone will bear the cost of transportation. The mine was opened previous to 1860, but has only been worked systematically during the last five or six years. The vein is a fissure vein from ten to twenty feet in thickness in the gneiss of the

Jan 1, 1882