Search Documents

By C. O. Tarr, G. V. Smith, R. F. Miller

Metallurgists have long recognized that the Fe3C type of carbide is not a stable phase in steel and that, given sufficient time, it will decompose with formation of graphite, at least at temperatures below about 205o°F.l This slow graphitization has never been of much concern to users of hypoeutectoid steels, for in such steels it occurs only during prolonged exposure at elevated temperature. In I935, Kinzel and Moore2 reported complete graphitization of the carbide of a 0. I5 per cent carbon steel that had been in service for about 26,000 hr. at a temperature of about IIOO° to 12oo°F. In discussing this paper, both Mathews and Sauveur reported graphitization of slightly hypereutectoid steels. In an extensive investigation of graphitization of high-purity iron-carbon alloys, Wells1 produced graphite at 7oo°C. (I29o°F.) in an alloy containing as little as 0.13 per cent carbon, and showed that graphite may precipitate either directly from austenite or from decomposition of Fe3C, also that the rate of graphitization tends to increase with increase of temperature, at least up to a certain point, and with the presence of graphite nuclei. Jenkins, Mellor and Jenkinson,3 studying the structural changes in carbon steels ranging from 0.17 to 1.14 per cent carbon during stress-rupture tests at elevated temperature, observed graphite in an aluminum-killed 0.40 per cent carbon steel after fracture in 4340 hr. under a stress of 17,900 lb. per sq. in. at 840°F. and in many of the steels after stress-rupture test at 12oo°F. Unstressed samples of 0.60, 0.86 and I.I4 per cent carbon steels graphitized almost completely in 360 hr. at I200°F., while samples of 0.90 and 1.10 per cent carbon steels were somewhat graphitized, and steels containing 0.24, 0.40 and 0.57 per cent carbon showed no sign of graphite. Their results indicate that graphite precipitates the more readily the higher the carbon content, though this tendency is influenced to some extent by deoxidation practice, and that graphitization is accelerated by plastic deformation. In a recent study of the graphitization of 0.4 and 0.6 per cent carbon steel strip, made by M. A. Hughes,4 it was found that at I2oo°F. graphite appeared after 72 hr. in aluminum-killed but not in silicon-killed steel, and that the rate of graphitization was increased by slow cooling from I6oo°F. and by cold-working prior to annealing. In creep tests of normalized 0.15 per cent carbon steel killed with 2.5 Ib. of aluminum per ton, at the U. S. Steel Corporation laboratory at Kearny, spheroidization and some graphitization were found after 3000 hr. at Iooo°F. under a stress as low as 1500 lb. per sq. inch. .

Jan 1, 1944

By B. W. Dyer

In 1924, the Crescent Eagle Oil Co., while drilling the salt section of the Paradox formation in Grand County, Utah, encountered a salt that did not appear to be sodium chloride. This salt was analyzed and showed the presence of potash minerals, both sylvite (KCl) and carnallite (KMgC12.6H2O). Because of the high potash content of the sample, there was considerable speculation: (I) as to whether the hole had been salted, and (2), if not, the extent, richness, and the depth at which the deposit occurred. The discovery caused a large amount of activity in the area. During the next few years, 68 potash prospecting permits were issued by the Government, 24 under the Act of 1917 and 44 under the Act of Feb. 7, 1927, each including about four sections of land. Several holes, all shallow, were drilled for potash. A number of holes were drilled for oil into the salt horizon and the cuttings collected at the oil wells were examined petrographically and chemically. The shallow test holes were not sufficiently deep to reach the potash horizon and revealed nothing of value, but several of the oil test holes gave some indication of where potash might be found. Location and Geology of Deposits The potassium and magnesium salts have been found in various places from the Denver and Rio Grande Western Railroad tracks about seven miles west of Thompsons, in eastern Utah, to Cane Creek, a tributary of the Colorado River— a distance north and south of about 35 miles. In this locality, there appear to be five separate deposits: the Crescent Eagle area, which is in T. 22 S., R. 19 E.; the Salt Valley area, in the vicinity of the north-south line of T. 23 S., between R. 20 E. and R. 21 E.; the Seven Mile area, in the eastern part of T. 25 S., R. 20 E.; the Cane Creek area, on the Colorado River, in T. 26 S. and T. 27 S., R. 20 E. and R. 21 E.; and the Salt Wash area, in T. 22 S. and T. 23 S., R. 16 E. and R. 17 E. (Fig. I.) The Crescent Eagle and Salt Valley areas are in the Salt Valley anticline, some of the wells being in the fault graben and others outside. Structurally, the Salt Valley anticline is very complex, and can be described in general terms as a northwesterly plunging collapsed anticline about 15 miles long. In the Crescent Eagle area, the valley graben is about 1 1/2 mile wide and the salt probably forms a plug, the apex of which is in the vicinity of the Crescent Eagle well. Owing to the complex structure, there has been every opportunity for flowage in the salt to cause local thinning or thickening of beds. The regular succession of formations in the general area* is: Cretaceous Mancos Dakota Jurassic Morrison Summerville Entrada Carmel

Jan 1, 1948

By B. W. Dyer

In 1924, the Crescent Eagle Oil Co., while drilling the salt section of the Paradox formation in Grand County, Utah, encountered a salt that did not appear to be sodium chloride. This salt was analyzed and showed the presence of potash minerals, both sylvite (KCl) and carnallite (KMgC12.6H2O). Because of the high potash content of the sample, there was considerable speculation: (I) as to whether the hole had been salted, and (2), if not, the extent, richness, and the depth at which the deposit occurred. The discovery caused a large amount of activity in the area. During the next few years, 68 potash prospecting permits were issued by the Government, 24 under the Act of 1917 and 44 under the Act of Feb. 7, 1927, each including about four sections of land. Several holes, all shallow, were drilled for potash. A number of holes were drilled for oil into the salt horizon and the cuttings collected at the oil wells were examined petrographically and chemically. The shallow test holes were not sufficiently deep to reach the potash horizon and revealed nothing of value, but several of the oil test holes gave some indication of where potash might be found. Location and Geology of Deposits The potassium and magnesium salts have been found in various places from the Denver and Rio Grande Western Railroad tracks about seven miles west of Thompsons, in eastern Utah, to Cane Creek, a tributary of the Colorado River— a distance north and south of about 35 miles. In this locality, there appear to be five separate deposits: the Crescent Eagle area, which is in T. 22 S., R. 19 E.; the Salt Valley area, in the vicinity of the north-south line of T. 23 S., between R. 20 E. and R. 21 E.; the Seven Mile area, in the eastern part of T. 25 S., R. 20 E.; the Cane Creek area, on the Colorado River, in T. 26 S. and T. 27 S., R. 20 E. and R. 21 E.; and the Salt Wash area, in T. 22 S. and T. 23 S., R. 16 E. and R. 17 E. (Fig. I.) The Crescent Eagle and Salt Valley areas are in the Salt Valley anticline, some of the wells being in the fault graben and others outside. Structurally, the Salt Valley anticline is very complex, and can be described in general terms as a northwesterly plunging collapsed anticline about 15 miles long. In the Crescent Eagle area, the valley graben is about 1 1/2 mile wide and the salt probably forms a plug, the apex of which is in the vicinity of the Crescent Eagle well. Owing to the complex structure, there has been every opportunity for flowage in the salt to cause local thinning or thickening of beds. The regular succession of formations in the general area* is: Cretaceous Mancos Dakota Jurassic Morrison Summerville Entrada Carmel

Jan 1, 1948

By H. H. Campbell

The following paper deals almost exclusively with the results of practice at the works of the Pennsylvania Steel Company at Steelton, Pa. From the records of the furnaces at this plant, both acid and basic, large and small, are drawn the data for the various demon strations, and on a long and intimate experience with their opera tions are founded many theories and generalizations. It may seem that universal laws should not be built upon a basis so restricted ; but in reality the condition is the strongest guarantee of validity. Each table investigates some- certain variable, and by virtue of the common origin of the factors, we have good ground for assuming the corresponding agents to be equal. The examples may or may not be instances of good practice, and may be open to criticism if regarded solely as exponents of • metallurgical success. But it must be remembered that the lists are not made up of selected specimens, nor are they chosen to show su perior results; they are gathered to investigate, by strict scientific methods, the formula? of the operation. In such work no untoward results should be eliminated, save those which bear upon their face the stamp of experimental error. If the worst members be omitted, then the best must also be omitted. Only by using every available case can an honest attempt be made to deduce a true average. It is recog nized, however, that with the most careful selection it is difficult, if not impossible, to collect data representing universal conditions. In each table the records tell of a special practice, and all conclusions drawn from them are true only within the limits between which the equations have been integrated. Not assuming the prerogative of speaking for American melters in all the opinions herein expressed, nor acting as a camera in por traying an ephemeral state of national metallurgical development,

Jan 1, 1894

By Albert Sauveur

As THE years go by, names of distinguished metallurgists will be added to the list of Henry Marion Howe lecturers, and now and then an illustrious one, for to be chosen to deliver the Howe lecture will be, I do not hesitate to predict, a highly coveted honor. I pray, therefore, your indulgence, if I confess to a feeling of gratification in having been appointed the first of these lecturers. It does not follow, however, that I am losing all sense of proportion and that I have an exaggerated idea of the little I have been able to contribute to our knowledge of iron and steel. Indeed, I fully realize how small were my claims to so great a distinction. I realize, also, that those entrusted with the task of selecting a lecturer were actuated, in coming to a decision, by their knowledge of the long and intimate friendship that had existed between the leader we have lost and myself. For their generous impulse, I thank them from the bottom of my heart; and with becoming modesty, I take up my task as the first Henry Marion Howe lecturer. It would be pleasant and indeed most appropriate to devote this entire lecture to a eulogy of Henry Marion Howe and his work, but how short the time for so large an undertaking and how inadequate my qualifications! On Aug. 28, Sept. 4, 11, and 18, 1875, a series of articles appeared in the Engineering & Mining Journal entitled "What is Steel?" With one exception, these constitute the first professional paper of Henry Marion Howe. That was nearly fifty years ago, three years after graduating from Harvard University. He was then but twenty-seven years old and already his keenly inquisitive mind was actively at work. There is a touch of romance in this young metallurgist who, on entering his. scientific career, destined to be so brilliant and so fruitful, on the very threshold of it, seems to have selected as his motto "What is Steel?" Like a knight-errant of science, he started on his quest for an answer to that question, a quest which was to last forty-seven years and which death only brought to an end. And while thus engaged how many wonderful messages we received from him, each one bringing us nearer to the goal! How illuminating, inspiring and encouraging were those messages! How well-equipped he was to wrench from nature some of the secrets she so jealously guards! How broad his learning and how clear his

Jan 5, 1924

By W. M. Johns

The geological mapping of Lincoln and Flathead Counties was a five-year project undertaken by the Montana Bureau of Mines and Geology. This paper, written by the Project Geologist of the survey, is primarily concerned with the stratigraphy of the Belt rocks encountered in mapping. Lincoln and Flathead Counties of northwestern Montana are underlain by sedimentary rocks of the Belt Series of Precambrian age. In only a very small part of the area, near Libby and Troy, have economic mineral deposits been worked with any success. Most of the area has been inadequately mapped as to geology. The region is crossed by the Great Northern Railway and served by the Pacific Power and Light Co.; officials of these two companies believed that with better geologic maps, prospecting might be stimulated and lead to the discovery of mineral resources that would contribute to new economic development within the area. A cooperative mapping agreement was proposed jointly by the two companies to the Montana Bureau of Mines and Geology in May 1958, and thus was born the Kootenai-Flathead five-year project. The dual objectives of this project are: 1) the possible location of mineral deposits of economic value, and 2) the ''stimulation of prospecting exploration" by others. This was to be achieved by geologic mapping of some 6800 sq miles and by establishing a field office in Kalispell where prospectors could come to have their rocks and minerals identified and receive geological advice on their problems. This writer has finished four field seasons as Project Geologist and thus became familiar with the Belt section in the Libby, Yaak River, Ural, Thompson Lakes, Pleasant Valley, and Stryker quadrangles (see Fig. 1). Progress on the project is given in annual reports issued by the Bureau.* This *Montana Bureau of Mines and Geology, Bulletins 12 (1959), 17 (1960), and 23 (1961). paper is concerned essentially with the stratigraphy of the Belt rocks so far encountered in mapping. PREVIOUS WORK IN THE AREA Willis28 made the first study of the stratigraphy and structure in the Lewis and Livingston Ranges of Glacier Park just east of the project area. In 1904, Daly made a study of the Belt rocks of the 49th parallel, using the names from bottom up, Creston, Kitchener, Moyie, and Gateway, for rocks ranging in age from that of Prichard to that of basal Missoula group. Walcott26 studied the Belt rocks exposed in the Mission Range (see Fig. 1) and other areas to the south of the area under discussion. Calkins and McDonald made a reconnaissance of northern Idaho and northwestern Montana in 1905. Calkins was the first to use Walcott's term 'Ravalli' as a group name for the strata equivalent to the Burke, Revett, and St. Regis formations (see Table I). Clapp worked on the Belt of western Montana (including Lincoln and Flathead Counties) throughout his lifetime. The Fentons9 studied the Belt of Glacier Park and

Jan 1, 1962

By G. E. Warner

This paper presents a review and analysis of a highly stratified Burbank sand waterflooding project in Osage County, Okla. Permeability values in this reservoir range from less than 0.1 md to nearly 3 darcys, and 90 percent of the permeability capacity is contained in approximately 26 percent of the reservoir volume. To date, the project has recovered 103 bbl/flood-acre-ft since waterflood initiation, which represents 50 percent of the total preflood cumulative and 12 percent of the original stock-tank oil in place (OSTOIP). The outstanding feature of this project has been the economical recovery of a sizable quantity of oil at water-oil ratios higher than those normally considered prohibitive. Nearly 70 percent of the recovery to date has been achieved at water-cut values greater than 95 percent. An ultimate waterflood recovery of 138 bbl/flood-acre-ft, or 67 percent of the preflood recovery and 16 percent of the OSTOIP, is predicted. The ultimate primary and secondary recovery will be 302 bbl/acre-ft and approximutely 40 percent of the OSTOIP. The actual performance is compared with the predicted performance by both the Stiles and the Dykstra-Parsons methods, and applicabiliry of these methods to this particular reservoir is evaluated. The performance of this project indicafes highly stratified reservoirs can be successfully and economically waterflooded when either reservoir or economic conditions preclude the use of mechanical and chemical means of mdbility control. Introduction The concept of the stratified reservoir has been used by reservoir engineers for many years to describe the vertical variations in permeability within a reservoir. Numerous techniques have been advanced to predict the expected waterflood performance of the stratified reservoir, and in most cases they prove reasonably accurate. The advisability of undertaking a prospective waterflooding project is determined, based on these predictions. This paper presents a review of a waterflood project in a highly stratified reservoir that normally would be considered a marginal prospect, at best, when evaluated with any prediction technique properly adjusted for reservoir conditions. This kind of project can be successful if the predictions are used to design a waterflooding system capable of economically recovering an oil cut of 1 to 2 percent. Experience gained in the early stages of the project's development was profitably applied in the later development of the entire reservoir and could prove beneficial to other projects with similar reservoir stratification or fracture characteristics. The East Burbank pool waterflooding operations have been developed in three separate stages, each of which has been a separate project: Mid-Burbank Unit, Flood A, and Stanley Waterflood. When referred to collectively, these projects will be called the Composite Project. The Skelly Oil Co.'s Barber lease — the only portion of the pool not included in the three projects — is operated as a separate facility with a cooperative injection-well agreement. It contains less than 80 productive acres and would not significantly affect the over-all performance picture.

Jan 1, 1969

By Arvid E. Nissen, Knox Taylor, John H. Hall

Some months ago one of the authors was asked to write a paper on the heat treatment of steel castings that would be more comprehensive than other matter he had published; this is an attempt to present in condensed form the results of experimental work and actual practice carried out for the most part in 1907, 1908, and 1909. It is not a laboratory research and the work done was carried out for the express purpose of putting in practice the processes discovered as fast as possible. Most of the tests are the result of commercial practice and not of bars annealed in our laboratory; most of the micrographs were made for our own records and not for publication. Certain of the micrographs, therefore, are not as clear as we may wish but they were good enough for our purpose at the time they were made. The tests and micrographs are selected from several thousands in our files. All of these micrographs are magnified 60 diameters. These experiments were conducted almost entirely on steel made in a 3-ton bottom-blown converter, and most of the steel illustrated analyzes about 0.05 in phosphorus and sulfur. Unfortunately, a certain number of specimens are shown of which we do not have the complete analysis, but in most cases in which the phosphorus and sulfur vary much from the figure just given that fact is noted. For purposes of comparison, we have included a certain number of micrographs and tests of steel made in the electric furnace, some of which were from specimens made in other shops and some in our own shop, and some tests of acid open-hearth and tropenas steel. A brief examination of the tests in Table 1 shows that certain treatments of, for instance, 0.30 per cent, carbon steel are not represented by any test data. Had this been a laboratory research, this information would undoubtedly have been furnished, but as this work was done for commercial purposes the omissions are due to the fact that, at the time the work was done, we saw no advantage in trying every composition of steel with each treatment discussed in the paper.

Jan 1, 1920

By H. NORTON JOHNSON

THE oil industry in California during 1929 reached new heights and new depths in the discovery and development of the oil resources of the State. The discovery of new fields, and more especially the discovery and development of deeper prolific sands in known fields has, for the first time in its history, brought the potential production of completed wells within the State to over 1,000,000 bbl. oil per day. Constant improvement in equipment and technique has made possible economic development to depths unheard of but a few short years ago. Commercial production from a depth of over 4000 ft. was considered quite an accomplishment in 1923 when the Meyer sand at Santa Fe Springs was developed, and when later oil was successfully raised from this depth.

Jan 1, 1930

By Williams, J. A.

THE Alaska Juneau mine has been developed through an adit driven at the elevation of the top of the mill and all mining is done above this main haulage level. As a result of wholesa1e"mining operations about 11,000 tons rock containing one dollar' per ton in gold is, hauled to the. concentrator during every 24 hr. Due to the method of mining, whereby a system of oreways delivers-the.ore direct from the stope to the bottom level of the mine, no tramming of ore is done on any of the upper levels. However, ;in doing exploratory drifting and crosscutting on the upper levels, the broken material is trammed by hand in 1-ton 18-in. gage cars to a nearby raise connecting with one of the several oreways. This constitutes the only tramming operation except that on the main level.

Jan 1, 1931

By John B. Hastings

THE reconnaissance of the Goldfield mining-district, described in this paper, was made in May and June, 1905, and, though this time was too short for a complete report, the work accomplished may serve as a basis for more thorough future research. Dr. Berkey has examined the rocks collected by myself, and I am using his classifications. As a result of further field-work, and Dr. Berkey's examination of the rocks, this paper is an elaboration and correction of my views expressed in the Gold-field Sun, May 12, 1905. The sketch-map, Fig. 1, illustrates the geology of the Goldfield mining-district. Goldfield is an eruptive complex, consisting of alaskite (binary granite), hornblende-andesite, hornblende-dacite, rhyolite, pyroxene-andesite, pyroxene-dacite (sometimes containing, a small quantity of olivine), quartz-felsite, olivine-pyroxene-ande¬site, and basalt. Considering this list to be arranged in the order of eruption, the age-sequence of the rocks conforms to Richthofen's law, formulated in 1868. From his observations in Europe and America, propylite, andesite, trachyte, rhyolite and basalt, occurring together, succeed one another. In a general way, the medium and more acidic rocks precede the most asic-a result supposed by some to have arisen from their relative position beneath the surface, and due to a rude stratification by gravity in the original cooling magma during the older history of the earth, or to the same differentiation occurring during a quiescent (molten ?) period preceding eruption, being aided by the ease with which acidic rocks, mixed with water vapors, become fusible. In effect, the more basic and less re-

Mar 1, 1906

By C. W. Allen, L. C. Moore

The Mather mine, of the Negaunee Mine Co., is within the limits of the City of Ishpeming. on the Marquette iron range in Michigan's Upper Peninsula. It is named for William G. Mather, who has served as President, and Chairman of the Board, of The Cleveland-Cliffs Iron Co. for well over 50 years. The property comprises nearly the square mile of section 2, T.47 N. R.27 W., which, except for 20 acres in the northeast corner, was leased by The Cleve-land-cliffs Iron Co. to the Negaunee company. The latter is a partnership of Cleveland-Cliffs and the Bethlehem Steel Co., organized to equip the property, retaining Cliffs in charge as operator. Shipments of ore from this area are mainly through Marquette, which is 16 miles to the northeast on Lake Superior, or through Escanaba, a Lake Michigan port, 65 miles to the south. Cleveland-Cliffs, in 1943, operated 12 mines in the Lake Superior district, with shipments of 6,635,576 tons for the year. Geology The north footwall of the Marquette Range synclinorium outcrops near the north line of set. 2, the iron formation dipping to the south at an angle of about 40. The south side of the trough reappears at a distance of 4J5 miles on sec. 26 and the surface geology between shows iron forma- tion or intrusive diorites. The latter are harder than most phases of the iron formation and, as a result of glacial action, appear as buttes or low-lying hills. The general elevation of sec. 2 is about 1450 ft. above sea level, or 850 ft. above Lake Superior, and the higher diorite outcroppings about 1600 ft. above sea level. The geological structure has been complicated by a series of major and minor faults, one of which may be illustrated by the diorite sheet, which tilts south with the iron formation in the north half of the section and then reappears near the center to repeat this sequence. Sectionally the geological series includes a nearly eroded capping of Goodrich quartzite followed by the considerable thickness of Negaunee iron formation, which is cut by intrusive dikes or diorite sheets, and underlain by the Siamo slates grading into quartzites. The ore deposits occur mainly in troughs formed by the intersection of impervious dikes and the footwall slate, but include locally enriched lenses or bands in the iron formation and also interbedded with the Siamo slate. The ore is a soft red hematite with an indicated dried analysis from the surface drilling to date of 61.50 per cent Fe, 0.134 Per cent P, 5.40 per cent Si, 2-87 Per cent A1 and 0.015 per cent S. Exploration A diamond-drilling campaign started in 1937 actually had its inception in 1917, when a number of shallow test holes were put down for the purpose of locating ore that might be quickly developed and mined

Jan 1, 1946

By E. R. Johnson

The copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the westem flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past I5 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7½ gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by I-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55½-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73½-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bill serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 13/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7½ McCully gyratory crusher set at 13/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73½ by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1949

By Arthur B. Foote

THE ball mill has superseded stamps for the reduction of gold ores in most of the recently designed plants, partly because stamps are not suited to die fine grinding required for flotation, and partly to save space and construction cost. Experience with these new mills seems to confirm the idea that it is more difficult to recover bold from a ball-mill product than it is when stamps are used for crushing. Microscopical examination of particles of gold that have passed through a ball mill show that the gold has been pounded into exceedingly thin flakes coated with a talcy surface, making it more difficult to save by amalgamation, flotation, or concentrating. Bearing in mind that gold is extremely malleable, it seems reasonable that this should be so. Contrast the action in a stamp battery, where the crushing is by impact in the presence of mercury, to the grinding and rolling under pressure in a ball mill. It is well known that a better recovery can be obtained by panning or amalgamation from a sample of ore that has been crushed by mortar and pestle than from one reduced on a bucking board.

Jan 1, 1937

By R. J. Stevens

The Roan Antelope Smelter commenced operations in October, 1931. As originally designed, its equipment consisted of one reverberatory furnace, 120 X 25 ft, two Peirce-Smith converters 12 X 20 ft, and one straight line casting machine. Since that time the following additions have been made: One reverberatory furnace 120 ft X 28 ft ('934) One reverberatory furnace 95 ft X 28 ft (1943) Two 12 X 20 ft Peirce-Smith converters (1934 and 1938) One 13 X 30 ft holding furnace (1938) One straight line casting machine and 2 ladle tilting quadrants (1934) The metallurgy of the smelting process is comparatively simple. However, there are several features of operation which are uncommon to most copper smelters: (I) The high grade of concentrate treated; this has always been about 50 pct copper. (2) The high flux burden on the charge. This is necessary because of the deficiency of bases in the concentrate and the high alumina content of the concentrate. (3) The frequent necessity of adding coal to the furnace charge to control the matte grade. (4) The high grade of matte produced. This has led to unusual converter problems. From the commencement of operations, the ore mined has come from the Roan Basin orebody. The concentrate produced from this ore consists mainly of chalcocite and shale with small proportions of other copper minerals. As mining operations extend to the Roan Extension orebody, the proportions of bornite and chalcopyrite in the concentrate will increase with a corresponding decrease in the copper content of the concentrate. Because of the concentrate grade the capacity of the reverberatory furnaces in terms of tons of copper produced per ton of coal burned is high. This ratio is usually over 2.2, and on especially favourable runs has reached 2.6. Reference to Table I shows that the iron content of the concentrate is unusually low. Only part of this iron is available for slag formation, the balance going to the matte. To make up this deficiency in bases, limerock is added to the furnace charge. This flux ensures a slag that is of the correct silicate degree, is suficiently fluid, of low specific gravity, and it counteracts the thickening effect of the alumina present. An ample supply of flux is obtainable from Ndola, 22 miles distant by rail. Although the reverberatory slag has a high copper content, the slag fall is low and the copper loss in the slag now rarely exceeds 1.0 pct of the total copper charged. The blister copper shipped is of such purity that only one fire refining operation has been necessary to produce a wirebar with properties comparable to electrolytic copper. Bismuth has always been the most troublesome impurity and consequently the problem of its control in the finished product has been of prime importance. Practically none is removed in the reverberatory furnace. The bulk of the elimina-

Jan 1, 1949

By L. S. Richardson, N. J. Grant

REACTIONS of oxygen and nitrogen at low pressures with titanium have recently been studied by a number of investigators.1-3 Gulbransen and Andrew' noted that the reaction with nitrogen followed the parabolic rate law whereas the reaction with oxygen deviated slightly from this law in the temperature range 300° to 800°C. In the work reported here, commercial titanium (75 A) was used as the test material. Cylinders 2.5 in. long and 0.25 in. in diameter were machined from heavier bar stock. The test pieces were given a metallographic finish, immersed for 30 min in cold concentrated HC1, washed in water, then acetone, and dried with lint-free cloth. Reaction rates were determined in a modified Sieverts type apparatus by measuring the decrease in gas pressure of the reacting gas contained in a constant volume. The amount of gas added could be measured in a calibrated gas burette to an accuracy of 0.01 mm. During the course of a run the temperature never varied by more than 10°C and then only for brief moments. After placing the specimen in the furnace, the system was first evacuated for 12 hr at room temperature, and then flushed with purified argon five times, adsorbed gases being discharged during this period from the glass system with a high frequency spark coil. The flushing and discharging were repeated at 400°C. This rather involved procedure was found necessary after a number of trial runs indicated extraneous effects traceable to the system. Reaction periods up to 2 hr were used, at initial gas pressures of 0.2 to 0.5 atm. Experimental Results Fig. 1 shows the decrease in oxygen pressure for tests at 0.5 atm at various temperatures as a function of the square root of the time. Deviations from linearity are minor and the parabolic rate law is obeyed. Fig. 2 shows the same plot for the nitrogen reaction. A definite deviation from linearity is noted; however, it is probable that the higher initial rates are caused by the presence of small amounts of oxygen contamination, the initial faster rate changing to the slower rate after about 5 to 10 min. Calculations of the rate constants were made on the basis of the latter portion of the curves. The parabolic rate law constants calculated from these curves are shown for oxygen and nitrogen in Fig. 3. In spite of some scatter the average curves are quite definite. Changes in gas pressure of the order of 20 pct did not result in a measurable change in the rate law constants. The activation energy for the oxygen reaction was calculated to be 47,400 cal per mol (above 700°C), which is not in agreement with the value quoted by Gulbransen and Andrew' for lower temperatures, their value being 26,000 cal below 600°C. The activation energy for the nitrogen reaction was calculated to be 45,400 cal per mol above about

Jan 1, 1955

By J. Mizrahi, A. M. Baniel, A. Mitzmager, S. Star

This article gives an account of the latest developments in the use of TBE for sink-float separation of silicate minerals. A number of minerals for which the process has been tested and found suitable are reviewed. Specific examples are discussed in relation to the particular problems of sink-float separation and recovery of TBE as compared with non-silicate minerals. The economic aspects are outlined. Silica and silicates comprise the most common and abundant group of minerals, and since they are present in variable amounts in most ores, they constitute an appropriate subject for the review and discussion of the recent developments in the use of TBE for mineral concentration. The silicates considered as a group have an extremely wide range of chemical and physical properties. Some of these properties, which are common to all minerals, are of importance to concentration by TBE and are discussed in some detail in this paper, as well as the development of methods and apparatus for concentration and recovery of TBE and several examples of concentration of silicates. PROPERTIES OF MINERALS WITH RESPECT TO CONCENTRATION BY TBE The properties considered as most important to concentration by TBE are specific gravity, structure, surface and shape. The specific gravity of a mineral is a fundamental property and is constant between very close limits for the same species of different sources if particles are pure and free from cavities or cracks. In many species, however, solid inclusions and changes in chemical composition due to replacement of elements cause variations in the specific gravity. The plagio-clase series of feldspars between albite and anorthite illustrate this point (specific gravity from 2.60 to 2.77). Fig. 1 shows the specific gravity distribution of some of the common silicate minerals.' The highest specific gravity is about 4.7 (zircon) and the lowest is 2.0 (sepiolite), with most of them ranging between 2.6 and 3.5. Although most of the silicates given in Fig. 1 are found as constituents of rocks, those generally considered as rock making minerals are comparatively few. They include quartz, feldspars, nephelite, sodalite, leucite, mica, pyroxenes, amphiboles, chrysolite, kaolin, talc and serpentine. These minerals may appear in igneous rocks as coarse crystals in granites, syenites and diorites or as very fine grained dispersions in basalt and felsite. When the latter rocks occur in an ore, their specific gravities depend on the minerals present and structure. The same is true for the sedimentary and metamorphic rocks (sandstones, shales, gneiss, slate, schists). A comparison of specific gravities for the minerals listed in Fig. 1 with that of TBE (see Table I) shows that the important rock-forming minerals, with the exception of pyroxenes, amphiboles and chrysolite (olivine), lie in the specific gravity range of less than 2.96 and can therefore be separated by TBE. The ore structure is important both in determining the apparent specific gravity and the efficiency of TBE recovery. The structure can be compact (as in

Jan 1, 1963

The Pueblo Viejo Mine, a 7, 250 mtpd (8,000 stpd) gold-silver cyanidation plant built by Rosario Dominicana S. A., was described in Volume I of this monograph. At the time of writing that volume, Pueblo Viejo had not yet gone on-stream and operating data or costs could not be presented. Since that time this information has been obtained and several interesting modifications and an expansion have been made to the plant. Because Pueblo Viejo is the largest open-pit gold mine in the world and one of the world's leading gold-silver operations with production of approximately 31 kg (1,000 oz) gold and 125 to 155 kg (4,000 to 5, 000 oz) silver per day, the authors have updated the previous data and flow sheet. The Dominican Government, which held a 4670 interest in Rosario Dominicana S. A., completed purchase of the mine to gain full control in 1979. Rosario Resources will continue to manage the mine, at least until the end of 1980. Gold was produced at Pueblo Viejo almost 500 years ago with initial production in the year 1505. Rosario Resources became interested in the property in 1969 and found surface oxidation had rendered the upper portion of the ore body amenable to direct cyanide treatment. The treatment of the underlying gold-bearing sulfide zone is still undergoing metallurgical studies. The ore is considered to be a laterite; and because there appeared to be few boulders in the ore zone, only a 400 m (16 in. ) square grizzly was initially installed ahead of the mills when the plant went on-stream in late 1974 at a design capacity of 7,250 mtpd (8,000 stpd). Operation also proved the ore to be harder than was originally anticipated. During 1967 a 1. 25 m by 1. 5 m (48 in. by 60 in. ) jaw crusher was installed to -feed the 1, 000 mt (1, 100 st) mill bin. Minus 200 mm (8 in.) crushed ore is fed directly to two 5.5 m by 1. 8 m (18 ft by 6 ft) semi-autogenous mills re-powered with 750 km (1,000 hp) motors and 50 mm (2 in.) grates. Each mill product is screened at 13 mm (1 /2 in.) by a vibrating screen. Screen oversize from each mill is combined on a single return belt equipped with a magnetic head pulley for grinding ball removal. The non-magnetic oversize is then split into two fractions for return to the primary mills. Originally, a minus 6 mm (1/4 in ) product was made on each screen and fed to a 300 kw (400 hp) 2.6 m by 3. 7 m (8-1/2 ft by 12 ft) regrind mill. During a plant expansion in 1978, an intermediate mill of 746 kw (1,000 hp) was installed to operate in open circuit on the combined primary mill

Jan 1, 1981

By F. S. White, E. L. Kinsella

THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to ' quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,1 showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.2 Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a 1/4-in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontally at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 1/2 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4 1/2-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1952

By W. I. Duvall, L. D. Sadwin

Three explosives with different detonation characteristics were tested by studying their cratering ability in a granite-gneiss. The strain wave generating characteristics of these explosives were also studied in the same rock medium. Correlations between the relative performance of three explosives as evaluated by crater studies and other methods of evaluation are indicated. Numerous test methods have been employed to evaluate the output performance of explosives; for example, the underwater explosion method, the airblast method and the ballistic pendulum method.'*' For blasting applications, the study of explosion produced craters and explosion generated strain waves are the most meaningful. This laboratory has employed these techniques extensively for many years and has shown that the detonation properties of explosives and their ability to generate strain waves in rock are related and that the amplitude and shape of the strain wave is related to some of the crater parameters such as slab thickness and fly rock velocity.3'11 However, a good comparison between the relative performance of explosives as determined by the crater and strain wave methods had not been made. The purpose of this investigation was to determine if the relative performance of three explosives as determined by the crater method shows a correlation with the relative performance as determined by the strain wave method. If a good correlation exists between these two sets of relative performance, it should then be possible to relate the detonation properties of an explosive to its ability to break rock in a crater test. In most commercial blasting operations, the diameter of the blast hole remains constant even though the type of explosive may change. In general, it is the explosive volume rather than the weight which remains constant when two or more explosives of different density are compared. Therefore all tests in this investigation were conducted on a constant volume basis rather than on a constant weight basis. TEST SITE AND ROCK PROPERTIES The tests described in this paper were conducted at a granite quarry owned and operated by the Consolidated Quarries Div. of the Georgia Marble Co. at Lithonia, Ga. The tests were performed in an area where the exposed rock surface was nearly horizontal and where the general rock mass had few joints or faults. The rock has an apparent sp gr of 2.6 and a longitudinal propagation velocity of 18,000 fps. The characteristic impedance of Lithonia granite gneiss is 53(lb - sec/in3). EXPERIMENTAL PROCEDURE There are many parameters which must be considered in the study of explosion-produced craters. The role played by each variable in the explosive-rock-crater system can be determined by experimental techniques in which one parameter is varied while others are maintained constant. In this investigation, the crater geometry was studied as the depth was varied for each of three explosives. The explosive volume and rock-type were held constant for all crater tests. The experimental arrangement used in performing the crater tests is illustrated schematically in Fig. 1.

Jan 1, 1965