Search Documents

By Karl Berger, Roman Schneeweis, Dietrich Mathweis

With increasing demands from customers to provide flat strip with tighter tolerances on material properties, particularly flatness of e.g. martensitic steel grades (M1500), it has become necessary to develop strategies to improve flatness without influencing the tensile properties for such hard steel grades. Usual skin pass mills are not capable to apply sufficient tension and roll force for these kinds of material to improve the flatness. Therefore, alternatives had to be searched for. This paper describes skin pass - / temper – rolling methods from the classical one to new alternatives in order to satisfy the demanding market of higher material properties and idle running mills in rolling plants.

Oct 1, 2019

By Nelson SOUTO, Nicolas LEGRAND, Christian COUNHAYE, Don EARLEY

The work is motivated by the automotive customer requirements for a roughness with high peak density (RPc > 75 peaks/cm) on steel sheet surfaces to maintain a good strip surface finish after painting. For that purpose, a new approach is utilized to compute roughness transfer and predict final roughness on uncoated steel sheets (average roughness, skewness, peak density) as a function of temper rolling conditions. The approach is based on the Monte Carlo method combined with the Abott curves and an auto-correlation function to numerically generate roughness profiles for roll and strip respectively. To compute the roughness transfer due to the interaction between roll and strip surfaces during rolling, a composite Abott curve that combines roll and strip Abott curves is used with an asperity crushing model integrated with a rolling model. This enables simulating two roughness transfer mechanisms in the roll bite: the strip asperity crushing mechanism by roll roughness and the strip asperity ploughing mechanism due to roll-strip interfacial sliding speed. The model shows the importance of considering the two mechanisms to predict roughness transfer correctly when strip elongation is high, typically a few percent, and roll bite friction is low. In these conditions, the forward slip at the exit of the roll bite tends to erode strip roughness significantly and decrease considerably the peak density on the strip. For lower elongation levels (~1%) and high roll bite friction, the ploughing mechanism becomes negligible and roughness transfer is controlled by the crushing mechanism only. With these two mechanisms, the model reasonably predicts the evolution of average roughness and peak density over a wide range of temper rolling conditions (new/worn work rolls, hard/soft grades, various elongations), but skewness is more difficult to predict for some trials.

Oct 1, 2019

By D. F. Rodríguez-Pérez, J. Salinas-Reyes, Luis R. Salazar-Garza, C. A. Gómez-De-La-Garza

The Pickling Line Tandem Cold Mill (PLTCM) from Ternium Pesquería started in 2013. It is a line with 5 stands, 6 high; focused mainly on the exposed automotive market, with a wide spread of products with high quality requirements. In addition the operational continuity is very important, for this, one of the greatest challenges is to ensure operational discipline, the order of production, the quality of the input (hot band), operational interruptions, equipment failure, breakage of strip in the mill, among others. In relation to this, it has a strong impact on productivity, customer compliance, damage to equipment, rolls, safety, quality, reprocessing among others. Here is present the results obtained in the project "decrease of strip breaks" which focused on several fronts, discipline in the order of production, previous review of raw material in surface and dimensional defects with automatic inspection equipment in the hot mill, as well as in PLTCM, generation of logic in the redundant systems of alerts and prevention to avoid or minimize strip breaks that were high impact in the past. All these multidisciplinary actions led as a whole to a significant improvement in the performance indicators of the PLTCM, in productivity, compliance, reprocessing and quality in the cold rolled mill.

Oct 1, 2019

By Juergen Meisel

The paper will explain how to successfully implement a robotic solution from the initial idea to a working industrial solution. Primetals Technologies can call upon 10 years of experience in installation of Robot solutions in the harsh environment of steelmaking plants - the so-called LiquiRob. To enhance an existing shroud manipulation system, the idea to connect the shroud with a bayonet mechanism to the ladle nozzle was born in accordance with the requirements of a well-known steel producer. The paper will describe the development steps from the first simulations and prototype testing in the laboratory, it will show the intensive system testing under workshop conditions and will finally depict the successful integration into the plant. Furthermore, operational experience will be shown as well as the advantages of such an installation compared to other shroud manipulation systems.

Oct 30, 2017

By Felipe Beluche Lima, Caio Augusto Silva Santos

Brazil is the largest producer of crude steel in the Americas by BOF process and many challenges come along with the increasing market demand. In the BOF, a tubular wall hood structure has been showing premature failures related to the overlay welded tube technology placed in the hood wall. The main root causes were: thermal fatigue at 1800°C, hot spot formation, high heat-affected zone (HAZ) leading to susceptibility of stress cracking, carburizing corrosion and superficial wearing. Based on that, co-extruded tube technology (named composite tube by Sandvik) was the alternative chosen to enhance hood performance without compromising BOF process. In order to rises safety and productivity, composite tube has 100% metallurgical bond assuring stable expansion, high heat exchange efficiency, better corrosion resistance and less rough surface finishing. It was highly suggested to many others mills due to similar and already existing reported cases.

Oct 1, 2019

By Michael Windhager

UltimaTM rolls have been designed for intermediate and finishing stands of rod and bar and small and medium section mills. The rolls and rings are spun cast, with a highly alloyed working layer and a tough nodular iron core. Microstructure and hardness level can be adjusted over a wide range, which allows us to adapt the rolls to differing rolling conditions. After introducing the UltimaTM concept, this paper will describe the results of UltimaTM rolls achieved in various mill applications, like finish rolling of rebar, and slitting. Special emphasis is given to performance gains when using UltimaTM rolls, compared to standard rolls. This paper also examines the impact of UltimaTM rolls on mill and roll shop productivity.

Jul 30, 2018

By Raúl Daniel López

Ternium-Siderar steelmaking has been focused in permanent improvements and process optimization. At present the Slab Continuous Caster N°1 has been totally transformed after 20 years of uninterrupted work. The authors of this paper summarize and comment on aspects which were the main changes and place emphasis largely on those technological developments in which they have been active during that period. Productivity and quality have been our goals during the last 20 years; it has led us to improve process and to achieve better control tools. In the development of this presentation, the authors will put special emphasis on the explanation of those works that were made following their own experiences through the technical personnel who belong to the staff of the company.

Jul 30, 2018

By Jan Krull

A high productive coke making process in connection with stringent emission control has clearly become a demand of plant operators and stakeholders. Further to this, availability, quality and coal costs are key concerns for the iron and steel industry in its efforts to optimize raw material cost. Today, the optimization of raw material cost in integrated steel works has further gained priority. Coking coal reflects up to 20% of the cost of steel. In top charged batteries coal preparation and blending is one of the concerns to lower coal cost by maximizing the percentage of non-coking coals in the blend. Stamp charging technology is technologically and economically an effective solution in the process of pre-carbonisation. Paul Wurth’s jumbo top charged oven as well as proven stamp charging technology have recently set new benchmarks in Europe, India and Brazil in terms of productivity, stability and emission control.

Aug 1, 2018

By Wen Xuan

Oolitic iron ores have significant economical importance because of their extensive resources in the world. However, their utilisation is often quite limited due to the high content of phosphorus inside. The phosphorus is often finely disseminated in the oolite structure and generally not liberated in the form of free particles. The iron ore used in this work is a typical oolitic goethitic iron ore with high phosphorus. The process of phosphorus removal from this ore is difficult because the phosphorus is not present as distinct minerals. As a result, no physical beneficiation process is able to separate the phosphorus from the iron bearing phases. The current concentrate contains low iron grade (Fe ~49%) and high phosphorus content (P 0.7~0.8%). The acid leaching is a potential way to dissolve phosphorus. Previous studies have shown that the thermal treatment makes the phosphorus more accessible for the acids and enables more efficient phosphorus dissolution. Some chemical additives are reported to enhance this phenomenon. A series of tests have been carried out using roasting - grinding - magnetic separation - leaching technologies to remove the phosphorus from this current concentrate. In the first stage, several tests were performed at pilot scale under the same conditions as described in some publications. The achieved results were similar to those from previous tests at laboratory scale. In the second stage, new test conditions were investigated in laboratory scale in order to achieve better result and to reduce the operational cost.

Aug 1, 2018

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By F. D. Rodriguez, J. Ramirez Cuellar, J. Salinas Reyes, C. Gómez-de-la Garza

The Pickling Line and Tandem Continuous Mill (PLTCM) at Ternium Pesquería Facility with a Five Stands, Six High configuration started in 2013. Manufactured by PRIMETALS, to produce steel to exposed automotive market, Turnkey project, with supervision of best practices from Nippon Steel. The main equipment that the process has are; Laser welding machine, 3 loopers, Scale Breaker, jet Pickling tanks, Inspection Station and COGNEX System Side Trimmer (flying width change), Type of Mill: UCMW(S) Carrousel, 2 Tension Reels. The principals goals are, Simulate production programs, validate materials for thin thicknesses before processing, low Re-welds, optimization use Cognex, good performance in Thickness, flatness and productivity.

Oct 1, 2019

By Rudolf Hubmer

In October 2013 JSW Steel decided to place an order to Primetals Technologies Austria (former Siemens VAI Metals Technologies) for the installation of a comprehensive Level 2 process optimization system for more than 20 existing production facilities of various suppliers. For SMS-I new L2 systems are provided for two hot metal pretreatment stations, three hot metal desulphurization stations, three ladle furnaces, two 1-strand slab casters, a ladle tracking system as well as a shop supervisory system. Additionally the existing L2 system for one 1-strand slab caster is being upgraded in the course of the project. In SMS-II new L2 systems for the 7 hot metal desulphurization stations, 4 ladle furnaces, 1 new RH vacuum degasser, ladle tracking system and a shop supervisory system are supplied. Despite of the challenging time schedule the commissioning of the single facilities started within less than 12 month after contract effectiveness. The installed Level 2 process optimization systems together with the achieved results are described in this paper.

Aug 16, 2017

By Francisco Morganti

In order to support hot rolling mill managers in improving the utilization of their plants, SMS group offers well defined Performance Modules. These are technologies, components, automation solutions or services, which can be implemented in existing plants to increase competitiveness in categories of efficiency, productivity, quality and process and product control referred to as “Industry 4.0”. Except the Performance Modules dedicated to the last category, targeting overall process controls, Performance Modules are characterized by quantifiable benefits. Performance Modules related to hot rolling mills are e.g. camber free rolling, modular laminar strip cooling system, new edge masking and intelligent components.

Oct 30, 2017

By Carlos Gonzalez-Rivera

An alternative cooling curve analysis method focused on the experimental determination of the latent heat of phase changes and phase transformation kinetics is proposed in this work. The method analyses the cooling process of a metallic sample, initially liquid that is contained into a cylindrical metallic mold, both of known weight, thermally isolated at its top and bottom. The method is based on an energy balance associated with the experimental measurement of the temperature change of the sample and the mold during their cooling process. From the numerical processing of the cooling curves, are obtained approximate values of the acting global heat transfer coefficient as a function of temperature in order to describe quantitatively the energy exchange of the metal/mold system with its surroundings. These relationships and other experimental data are used to process the cooling curve of the sample and the mold during solidification, in order to obtain the latent heat of solidification.The method was applied experimentally to zinc and tin of commercial purity, initially liquids and contained into stainless steel molds in order to determine its ability to measure the latent heat of solidification. The obtained results suggests that this method shows a good potential to characterize the solidification of metals.

Oct 30, 2017

By Mühlböck Marlene

Increasingly stringent global environmental regulations are forcing steel producers to continually improve the efficiency of sinter waste gas treatment. With the Selective Waste Gas Recirculation (SWGR) system from Primetals Technologies, lower production costs can be achieved and the size of downstream waste gas cleaning units can be reduced for investment savings. SWGR features the extraction and reuse of hot sinter off gas from selected wind boxes along the sinter strand, which contributes to improved energy efficiency and off gas treatment in the sintering process. With the next generation of SWGR, Primetals Technologies can provide an energy optimized, emission optimized and environmentally friendly solution that meet customer requirements and country specific regulations. This paper demonstrates the latest developments in selective waste gas recirculation, especially results from pot grate tests and comparison from lab to real plant data. Furthermore theoretical finding and mathematical modelling is presented.

Aug 16, 2017

By Ananda Moreira Vaz Ourique de Avila

Ferritic stainless steels have been used in the making of high and intermediate temperature operation solid oxide fuel cells (SOFC) interconnects, replacing the ceramic materials. However, at high temperatures, on the order of 700-850 0C, these steels can present significant oxidation and degradation processes, promoting increased electrical resistivity and corrosion losses that result in contamination of the electrodes and reducing the performance and the useful life of the SOFC. Thus, the knowledge on kinetics of oxidation/corrosion of these steels and their relationship with the microstructural transformations are of great importance. In this study, samples of ferritic stainless steels AISI 430, AISI 441 and Crofer22APU® were tested for oxidation at high temperature (800 0C) for long periods of time (up to 3,600 hours) and mass gains were monitored allowing the determination of the oxidation behaviors of these steels. Additionally, the microstructural characteristics of the samples before aging (corrosion-oxidation test) and after various oxidation times were evaluated by optical (OM) and scanning electron microscopy (SEM), as well as by micro chemical elemental analysis (EDS) and X-ray diffraction (XRD) phase analysis. Electrical characterization allowed determination of electrical area-specific resistances (ASR) characteristics of the systems studied, thus relating the electrical and oxidative behaviors of steels evaluated.

Aug 7, 2018

By Wujian jun

In the process of wire rod production, the rolled wire products must be cooled from the red-hot state to the normal temperature state. How to cool the wire rod after rolling is one of the key links of product quality control in the whole wire rod production process. In this paper, combined with the closed-loop transformation project of controlled cooling temperature of Xuanhuan iron and steel group co., LTD., the closed-loop related controlled cooling equipment (including water cooler, valve table, etc.), nozzle layout and process layout of water tank, and closed-loop software control system of controlled cooling temperature of high-line are analyzed and designed. Closed-loop system design USES temperature of cooling water cooling and water cooling two temperature closed loop regulating circuit, through temperature feedback and feedforward to achieve the uniformity of temperature adjustment, in order to prevent occur due to temperature closed loop control function with the phenomenon of a steel before and after the temperature difference is bigger, system Settings have "absolute temperature regulation" and "relative temperature regulation" selection mode. The system has a self-learning mode, which can modify the temperature feed forward formula. In addition, this paper takes the hard wire 82B rod as the test object, and studies the process parameters and the comprehensive mechanical properties of the rod before and after the water cooling system reform. The research results show that the temperature closed loop system, can ensure the rolled piece temperature control precision of plus or minus 10℃, enhances the stability of wire rod cleaner performance. It can reduce water consumption by about 186m3/h and improve the utilization rate of cooling water.

Oct 1, 2019

By Augusto César Barrios Tamayo

The high temperature erosion of Thermal Barrier Coatings (TBCs) is one of the main factors that define the lifespan in gas turbine components as it is considered the second source of failure of hot path components in power and propulsion turbine operation. The worn Top Coat (TC) surface in components such as first stage turbine blades affects the turbine efficiency due to energy losses and the increment in heat transfer to substrate. The first part of this work consists in describing a HTE test facility developed to emulate the damage conditions found in a number of components of gas turbines; in this testing machine, the samples were exposed to combustion gases moving at velocities close to 1.5 Mach and temperatures of 1100°C. The second part consists in the characterization of liners and first stage turbine blades of a GE7FA gas turbine used for power generation. The last part deal whit correlation of the features of TC’s worn surfaces with the erosion conditions and the dominant degradation mechanisms between test samples and turbine components were compared.

Jul 31, 2018

By Piotr Pajaczkowski

Hydro generators installed in Itaipu Binacional power plant with 824/737 MVA rated output power (50/60 Hz) belong to the largest ones in the world. Among many unique features the generators are equipped with the largest hydrodynamic thrust bearings ever built (external diameter 5200 mm, axial load equals approximately 3600 t). This paper is an attempt to propose a new thrust bearing design with the use of the state-of-the-art technologies and simulation techniques that demonstrate a reduction of friction power losses generated by the thrust bearing. This paper is divided into two parts. Within the first one the original thrust bearing design which was implemented in the generators is described. Related calculation results based on a thermo-elasto-hydrodynamic (TEHD) calculation software used by Alstom will be presented. A comparison between measurement results gathered in the 1980’s is given. In the second part a potential solution of a more beneficial bearing design is described. The proposed thrust bearing design modification is an implementation of Alstom’s PolypadTM coating. This modern polymer (PEEK) coating material has already been used by Alstom in projects around the world for many years. This coating allows pushing the operating parameters limits toward higher temperatures and lower oil film thicknesses far beyond the limits known for the conventional bearing materials.

Jul 31, 2018