Search Documents

By M. Schafer

The 6-m- (20-ft-) diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT3) has been completed. This article summarizes aspects of liner design and ad-dresses the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented. The Mill Creek Phase 3 tunnel (MCT-3) is expected to be completed this year. It is one of the largest tunneling projects undertaken by the Northeast Ohio Regional Sewer District (NEORSD) to date. The tunnel horizon is situated within the Devonian Chagrin Shale rock formation at an average depth of 85 m (280 ft). The tunnel was excavated using a two-pass method. A full face, fully shielded, Robbins 7.2-m- (23.8-ft-) diameter tunnel boring machine (TBM) was used to excavate approximately 4,500 m (15,000 ft) of tunnel and facilitate installation of initial supports (first pass). The final lining (second pass) consists of 305-mm- (12-in.-) thick cast-in-place reinforced concrete and integral low flow channel. Seven shafts were constructed on the project. The excavation of the tunnel commenced at Shaft 14 and proceeded down grade to Shaft 9, the terminus shaft. Because of the presence of overbreak in the tunnel crown, measures were required to support the form and counteract the effects of buoyancy during concrete placement.

Jan 1, 2008

By Rayner B

Five wells have been drilled in the Basker/Manta Block of VIC/P19, Gippsland Basin, resulting in sub-economic Intra-Latrobe Group oil and gas discoveries at Basker-1 and Manta-1. A total of 21 individual hydrocarbon bearing sandstones were intersected by the two wells. These reservoir sand bodies were deposited by fluvial processes in a lower coastal plain environment. The modelling of sand body orientation and geometry is a critical component in the evaluation of the two accumulations. Seismic resolution of the thin (average 2 m to 5 m) sand bodies is inadequate for mapping their orientation and distribution. Dipmeter data has been successfully applied to the problem of orienting the sand bodies using FMS images acquired during the drilling of Gummy-1 and reprocessed HDT data from Basker-1 and Manta-1. Prediction of lateral extensiveness (geometry) of individual sand bodies has also been attempted. Interpreted palaeocurrent direction from all three wells is dominantly from the NW to the SE. Reservoirs in the Manta-1/Gummy-1 area are interpreted to be predominantly channel sands, deposited by relatively low sinuosity streams. As such they would tend to have a laterally extensive, elongate geometry. Sand bodies deposited in the Basker-1 area show a predominance of laterally accreted cycles deposited by meandering streams. Channel geometry may then be limited in the downstream/upstream direction by internal permeability barriers such as clay plugs.

Jan 1, 1992

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion. In several cases, breaches occurred between the gravel pit and the river. Initial evaluation of several sites that experienced these breaches showed that impacts to the river system were complex and varied significantly from site to site. The impacts to the adjacent river system may be viewed as positive and negative. Several flood-plain-mining sites in Oregon located in areas of historic river flow reverted to active riverbeds. In many cases, state and federal fisheries biologists and university researchers saw the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries —Mined Land Reclamation Program (DOGAMI-MLR) is studying the effects to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound flood-plain decisions regarding mining.

Jan 1, 1999

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

The Grand Isle sulfur mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, La. The deposit is on acreage covered by oil, gas, and mineral leases originally issued in favor of Humble Oil & Refining Co. by the State of Louisiana which were continued, maintained, and redesignated by the U.S. Department of the Interior after passage of the Outer Continental Shelf Lands Act. The sulfur deposit was discovered in 1949 when Humble Oil & Refining Co. penetrated more than 200 ft of sulfur-bearing limestone in a zone between 1813 and 2075 ft below sea level. In 1954, Humble drilled ten more sulfur prospect holes, eight of which encountered sulfur ore. On September 19, 1956, Freeport Sulphur Co. acquired from Humble Oil & Refining Co, the sulfur rights underlying the tracts, and the actual design of the installation began the same month. The first structural contract was awarded in December 1957 and offshore erection began in June 1958. The initial phase of construction has been completed and production by the Frasch process commenced in April 1960. The estimated total cost of the project is $30 million, of which $8 million is the extra cost incurred by the necessity of offshore operations. More than $22 million was expended before production was started. GEOLOGY OF DEPOSIT Grand Isle is the third largest sulfur deposit in the U.S. The orebody embraces several hundred acres, but its outer limits are yet to be defined to the northeast, east, and south. Most Gulf Coast sulfur deposits occur in a caprock mantle of calcite (referred to as limestone), anhydrite, and occasionally gypsum, which covers the apex of an intrusive mass of salt. Commercial quantities of sulfur are usually confined to the calcite or limestone member. Most often such limestone is completely enclosed by dense anhydrite below and impervious sediments above, which effectively form a closed reservoir. The depth of the Grand Isle orebody ranges from 1800 ft to 2500 ft below sea level. Within the present boundary, the sulfur-bearing limestone varies in thickness from 220 ft to 425 ft, while the sulfur content varies an average of about 15 pct in the leanest hole to an average of about 30 pct in the richest. Rock containing less than 5 pct sulfur is not classed as ore, and holes assaying less than 20,-000 long tons per acre of sulfur in place are not considered commercial offshore. The sulfur enrich-

Jan 1, 1961

By L. J. Moore

Introduction Hydrometallurgical solvent extraction (SX) processes – featuring large quantities of combustible or flammable organic solvents - are common in the mining industry for recovering non-ferrous metals such as copper, nickel, cobalt, uranium, tungsten, iodine and lithium. Recent fire loss incidents and the widespread use of sub-grade tank farms and piping trenches, plastic piping, poor drainage, and closely spaced buildings demonstrate opportunities to improve the use of Inherent Safety (IS) in this industry. The mining industry has designed and constructed facilities with an emphasis on personnel safety, production efficiency and cost effectiveness. The use of IS to eliminate or minimize property fire exposures has not seen widespread practice. Lessons learned from the mainstream CPI have not been communicated or applied. As an example, copper SX plants have consistently used design of gravity flow as a cost and production-effective solution for transferring liquids and minerals through the process. In fact, Jergensen1 recommends to “utilize gravity to the fullest extent possible” in design of SX plants. This philosophy has been achieved by laying out SX plants with process equipment at different grade levels so that solutions can flow “downhill”. Because of the use of large quantities of flammable liquids and the potential for these liquids - if released – to flow unimpeded into other areas – gravity SX processes represent severe inherent fire consequences unless costly barriers, drainage and channeling are also provided. It appears that little thought has been given to the fire protection consequences and challenges of this design feature during the evolution of SX plants and most copper SX plants constructed today use some form of a sub-grade processing area (tank farm) and one-way gravity flow. While this layout is used to assure a cost effective operation it has resulted in significant exposures to high value production. The use of sub-grade production units is an inherently unsafe layout where flammable liquids are used and is a layout that would rarely if ever be used today by the mainstream CPI. Gravity-assist layout is only one example where copper SX plants have been designed and constructed without IS in mind. The use of combustible and frangible corrosion-resistant materials – such as glass, wood and plastic - for flammable liquid storage, processing and piping systems has significantly increased the hazards of these facilities. These materials of construction are not rigorous and allow for rapid failure and release of flammable contents during fire exposure. The use of combustible or frangible systems to handle or transport flammable liquids is not a practice seen today in the CPI.

Jan 1, 2006

By D Brouwer, P Wild, B Belle

Due to the steep geo-thermal gradient in Bowen Basin area, as underground coalmines reach increased depths of extraction, the Bulk Air Cooling (BAC) requirements will increase as opposed to cooling the workplace using the ventilation means alone. One such mine has already been using a 4 MW surface BAC plant for the last six years to manage the working temperatures with reduced cooling efficiency as the mine expands. Due to the horizontal nature of the longwall mine layout, distances from the working face to intake shafts are rapidly expanding to over 6 km as opposed to the vertical mine layout of a hard rock mine. To improve the positional cooling efficiency, reduced panel pressure differentials, improved rib emission gas management, and intake dust management, small diameter intake shafts were located on the inbye end of production panels and halfway up the development panels with localised mobile small BAC plants. This paper summarises the results of extensive underground data of this innovative cooling concept for development and retreating longwall face heat management compared to a larger remote BAC plant.CITATION:Belle, B, Brouwer, D and Wild, P, 2017. The use of mid-panel ventilation shafts to improve positional cooling efficiency in a Bowen Basin longwall mine – a case study, in Proceedings Australian Mine Vent Conference 2017, pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By C. W. Siyasiya, K. A. Annan, W. E. Stumpf

"SynopsisThe relationship between niobium content and austenite grain growth has been investigated through hot rolling simulation on a Bähr dilatometer. The effect of delay time between passes during rough rolling in Nbmicroalloyed steels with nitrogen contents typical for electric arc furnace (EAF) melting was studied. The results indicate that the grain growth constants n, Q, and A increase with an increase in Nb content. The activation energy for austenite grain growth Q was found to be in the range of 239 to 572 kJ/mol, the exponential constant n ranged from 2.8 to 6.2, and the material and processing condition constant A from 4.24 × 1012 to 4.96 × 1028, for steels with niobium contents ranging from 0.002% Nb to 0.1% Nb. A general constitutive equation for the prediction of austenite grain growth in these Nb-microalloyed steels under rough rolling conditions has been developed. Good agreement between the experimental and the predicted values was achieved with this constitutive equation.IntroductionGrain refinement has been found to increase both the strength and toughness of steels (Gao and Baker, 1998; Sharma, Lakshmanan, and Kirkaldy, 1984; Seok et al., 2014; Maalekian et al., 2012). It is also known that the austenite grain size directly influences the microstructure, and thus the mechanical properties, of the steel (Maalekian et al., 2012; Yue et al., 2010). Effective grain growth control is reported to be achieved through addition of precipitate-forming elements, such as Nb that, slow down the grain boundary migration through pinning and solute drag mechanisms (Yu et al., 2010; Olasolo et al., 2011; Alogab et al., 2007). Much work has been carried out on austenite grain lsize control by the addition of precipitate-forming elements that have a strong affinity for interstitial elements, such as carbon and nitrogen, which form the dispersed pinning particles to inhibit the austenite grain growth (Alogab et al. 2007; Hodgson and Gibbs, 1992; Nanba et al., 2003; Flores and Martinez, 1997; Rollett, Srolovitz and Anderson, 1989). Austenite grain growth can be described using a conventional or a modelling approach. With conventional approaches (e.g. metallography), in-situ monitoring of austenite grain growth at high temperatures is impossible. Modelling the grain growth behaviour based on available data is the ideal option. To quantitatively describe austenite grain growth therefore requires development of a sound mathematical austenite grain growth equation that accounts for the effects of the varying microalloying elements in inhibiting austenite grain growth. Numerous attempts have been made to develop an empirical model based on the general equation developed by Sellars and Whiteman (1979). Many of these models do not account for the direct effects of the microalloying elements such as Nb in austenite grain growth control [Fu et al., 2011; Wang and Wang, 2008; Wang et al., 2006; Shanmugama et al., 2005; Banerjee et al., 2010; Pous-Romeroa et al., 2013). The current work has considered this limitation, taking into account the direct effect of niobium in grain growth control during thermal processing. This is done by incorporating the initial austenite grain size Do and the microalloying element niobium in the development of a constitutive equation for grain growth prediction in Nb-containing microalloyed steels."

Jan 1, 2015

By Douglas Banks

Construction for the new 2.5 MGPD raw water intake project commenced December 2002. The project, initially designed as a 12' Ø concrete lined intake shaft,145' deep, with two offset 24" lake taps, 520' and 470' long was subsequently “value engineered” running the two lake taps through a single conduit. The offset for summer and winter pools was accomplished via a second shaft located at the lakes edge. Construction involved the use of blind drilling techniques for the shaft development and drill and blast techniques for the tunneling. All works were completed through extremely hard crystallized sandstone. The project came online August 12, 2004.

Jan 1, 2005

In most mines using presplitting the final excavated wall shows a zone of damage just below the crest and well defined presplit half barrels. The crest damage (surface dilation) zone varies and is added to by subsequent adjacent perimeter blasting operations. Keeping the preconditioning to a minimum is possible using the methods described in this paper, developed on several diverse and geographically distant mining operations to control crest dilation and preconditioning by presplitting in advance - not just laterally but vertically in advance. The first documented case (Delbridge, Marton and McSweeney, 2004) in the development of the concept was undertaken at AngloGold Australia Pty Ltd's Sunrise Dam Gold Mine (SDGM), located beside Lake Carey, some 730 km northeast of Perth, Western Australia. The mine had been developed in a series of cutbacks to a depth of over 300 m and began underground mining during the latter stages of open cut operations. This mine is fairly unique in that it utilised a single pass vertical presplit which initially extended over three bench heights and after the failure mechanisms were understood, over four benches. The presplit drilling for the three stacked benches started on the floor of the second bench so that any dilation was confined to the surface one bench above the crest and modified perimeter blasting was then developed to curtail damage from blasting adjacent to the new crest. The second case is based on a South African coal mine in the Witbank Coal Measures, 140 km northeast of Johannesburg, Republic of South Africa (RSA). It was important that blasting for optimal wall stability and minimal scaling was developed in advance. A dragline is scheduled to excavate the #2 seam midburden which is the lowest of the economically viable coal seams in the five seam Witbank Coal Measures. Mining of the overburden, coal and partings above the dragline midburden pass are by excavator and truck and each mining layer is individually blasted. The results of presplitting the midburden through the overlying coal seams and partings have provided a presplit with no surface dilation of the midburden crest and ensures any subsequent crest loss is solely due to blasting adjacent to the vertical presplit. Typical of all coal mines in South Africa only vertical presplits are used. Wall control is most commonly delivered by presplit blasting and one common sight after the dust clears is a ridge of broken blocks along the presplit row, usually with a main crack running between the presplit blastholes and often parallel cracks either side of the perimeter line. The surface rock strata or block structures have been dilated by the venting gases and shock waves. Decoupled, fully coupled, single or double deck charges are used depending on a variety of factors, anecdotal practices and perceived benefits. Preconditioning of the crest rock by blasting from above may not be visible to the naked eye (or non-existent in overburden in strip coal mines) but the high speed venting of explosives gases (and often the water in the presplits) preferentially follow existing cracks and structures because there is no developed presplit crack near the surface. This nearly always lifts, shifts and separates the surface structures and geological layers. Stopping the dilation by 'sacrificial' or 'in advance' presplitting has been shown to reduce the crest loss at both metal and coal mines. Drilling and presplit blasting through an upper level of bench or layer provides a degree of restraint to the target layer where the crest must be maintained and any damage caused by the venting gases will not cause concern as it is removed as planned, leaving a stable crest.

May 1, 2010

By Thierry Bernard

This case study shows how a unique combination of field measurements and advanced technologies allowed blasters designing, loading and firing an incredibly challenging quarry blast.

Jan 1, 2015

By Dean Bray

During the past three years, a new rear-dumping dragline bucket technology has been patented, developed and tested at North Dakota coal mines. Field testing has shown that this new concept in dragline bucket technology can improve strip-mining efficiencies by reducing cycletimes and increasing dumping radius. This article details the process, participants and the results for the development of a rear-dumping dragline bucket. Participants in the process In November 1995, the board of directors of Dakota Coal authorized the execution of a field test and option agreement and a license agreement with the partnership of D.F. Schmidt, electrical/maintenance supervisor, and Bill Lengenfelder, president of Modern Industrial. The board also authorized entering into a dragline bucket field-testing agreement with the Falkirk Mining Co.

Jan 1, 1999

By Laura McNally

In 2006, McNally International Inc., in a joint venture partner-ship with Aecon Constructors, was the successful bidder on two York Region Tunnel Projects: the Bathurst Collector/Langstaff Trunk Sewers and the York Durham Sewer System (YDSS) Interceptor Sewer 19th Avenue, both in the Toronto area. These projects comprised a total of 13 km (8 miles) of 2.74 m (9 ft) finished diameter tunnels and are both part of the YDSS. Both contracts required the use of earth pressure balance (EPB) tunnel boring machines (TBM) with a precast concrete segmental liner.

Jan 1, 2008

By Hibbert W. D, Lottrey A

The behaviour of coal in a process is a function of both the coal properties and the processing conditions. In the case of the Loy Yang coal deposit, extensive testing has been undertaken to determine: ò the extent, distribution and structure of the coal resource; ò the variations in properties throughout the resource; and ò evaluation of the behaviour of the coal during processing. This has involved the conduct of an extensive borehole drilling program, backed by geological modelling and material characterisation (chemical, physico-chemical and petrological). Evaluation of the behaviour of the coal during processing has ranged from theoretical modelling, laboratory-scale investigations through to pilot scale and full-scale tests. Until recently, the bulk of the work was directed at evaluating the behaviour of the coal for existing pulverised fuel (pf) firing/steam boiler technology and a high level of understanding has been developed of both the coal resource and its behaviour within these systems. More recent efforts have been directed towards the evaluation of new technologies directed towards cheaper and more efficient power generation using this coal. Loy Yang coal has been evaluated in the following technologies: ò Hydrothermal dewatering/direct coal-fired gas turbine; ò Steam fluidised bed drying; ò Solar drying/densification; ò Briquetting; and ò Gasification.

Jan 1, 1992

By V. Pawlowsky-Glahn, E. Pardo-Igúzquiza, J. J. Egozcue, R. A. Olea

Compositional data constitutes a special class of quantitative measurements involving parts of a whole. The sample space has an algebraic-geometric structure different from that of real-valued data. A subcomposition is a subset of all possible parts. When compositional data values include geographical locations, they are also regionalized variables. In the Earth sciences, geochemical analyses are a common form of regionalized compositional data. Ordinarily, there are measurements only at data locations. Geostatistics has proven to be the standard for spatial estimation of regionalized variables but, in general, the compositional character of the geochemical data has been ignored. This paper presents in detail an application of cokriging for the modelling of compositional data using a method that is consistent with the compositional character of the data. The uncertainty is evaluated by a Monte Carlo procedure. The method is illustrated for the contents of arsenic and iron in groundwaters in Bangladesh, which have the peculiarity of being measured in milligrams per litre, units for which the sum of all parts does not add to a constant. Practical results include maps of estimates of the geochemical elements in the original concentration units, as well as measures of uncertainty, such as the probability that the concentration may exceed a given threshold. Results indicate that probabilities of exceedance in previous studies of the same data are too low.

Jan 1, 2015

By Dan Marshall, David H. Watkinson

Abstract - Cobalt, Ontario, is renowned for the 12.6 billion grams (445 million ounces) of silver produced from the area since discovery in 1903 by workers of the Timiskaming and Northern Ontario Railway. Native silver generally occurs with cobalt arsenides and sulfosalts in near-vertical carbonate veins cutting the Huronian sedimentary rocks of the Gowganda Formation, the Archean metavolcanics and/or the Nipissing diabase. All major deposits have been found within a few hundred meters of the unconformity between the Archean and Huronian rocks in general proximity to the Nipissing diabase and volcanogenic sulfide mounds within the Archean meta-volcanics. Silver has been mobilized from one or more of the local country rocks by hyper-saline brines and deposited in or near zones of mixing where the saline brines encounter paleometeoric water transported to depth along the unconformity or local structures. Previous work has shown that chloride complexes are the dominant ligands responsible for silver transport. These hypersaline brines, represented as halite-bearing fluid inclusions at room temperature, have been trapped as primary fluid inclusions within vein minerals. Pressure-temperature conditions of vein formation have been derived from mineral equilibria, maximum lithostat and fluid-inclusion studies. These data are consistent with vein formation occurring over the temperature range 300°C to 350°C, with pressures constrained between 60 Mpa and 136 Mpa (600 bars and 1360 bars).

Jan 1, 2000

By D. M. Wagner, G. Biggs, M. Osmundson, C. J. Twaroski

Potential air emission impacts to federal Class I areas from distant sources are receiving increasing scrutiny by federal land managers (FLMs). This paper provides summary results of the impact analyses conducted for FLMs and PSD permitting of a proposed expansion for a taconite processing facility. Results from air quality increment, acid deposition, mercury deposition, and visibility analyses for Class I areas located 50 to 162 km from the facility showed the project would meet the respective regulatory and guideline values for the specific analyses. During the course of the air quality analyses, potential new requirements from the FLMs’ Air Quality Related Values Workgroup (FLAG) efforts and USEPA’s Regional Haze Program were brought into the PSD discussions. The implications for these future guidelines and regulations as they may affect future expansions at other mineral processing facilities are also discussed.

Jan 1, 2001

By M. S. Raseroka

An experimental rig has been constructed to produce chloride stress corrosion cracks in Type 304L stainless steel tube samples. The samples are to be used to test possible in situ repair methods in future work. The factor which influences the time to failure most strongly is the sample temperature; the distribution of cracks within the sample is affected by local temperature variations and by the position of the water line. Low-frequency oscillations in stress, caused by the on-off temperature controller, did not appear to influence cracking in these tests.

Jan 1, 2009

Jan 1, 1963

The 107th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Wednesday, 11 August, 2004. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: Ralph Bagirathi, Executive Member, African Mining Association Rudi Rudolph, President, Association of Mine Managers of South Africa Andrew Whibley, President, Association of Mine Resident Engineers of South Africa Dr Con Fauconnier, President, Chamber of Mines of South Africa Nxolisi Diliza, Chief Executive Officer, Chamber of Mines of South Africa

Jan 1, 2004

By Pupazzoni P. D, Meissner D. C

Incorporating an iron ore pelletising plant, a MIDREX'"' Direct Reduction Plant, and a mini mill, the conversion of iron ore fines to high- quality steel slabs in Western Australia is among the lowest cost routes in the world. The cost and availability of iron ore and natural gas, government support, and proximity to the growing Southeast Asian market all contribute to the competitive position of the area. Owing to the lead-time required, this is an ideal time to develop a new project to supply semi-finished steel to Asia for rolling to a finished product. A project contracted now will start up in about three years, when the market should have recovered.

Jan 1, 1999