Search Documents

By Kanau JL, Kilgour I

This paper describes the metallurgical processes at the 80 000tpd Ok Tedi Mining Limited concentrator, which treats copper- gold ore by single-stage crushing, SAG and ball milling and flotation to produce over 500 000tpa of concentrate. Plant and process developments, including installation of column cells, reduction of fluorine in concentrate, use of sulphidisation and process control improve- ments are also discussed.

Jan 1, 1991

By Knevitt L. T

PART 1Details of Kiewa Scheme.Introduction.Topography.Preliminary Investigations.Geology.Description of Project.Details of Main Works.Main Transmission of Power.Construction Facilities.PART 2Underground Works.Summary of Projected Works.Administration.Labour.Surveying.Safety and Accident Prevention.Medical Attention and First Aid.PART 3No. 4 Head Race Tunnel.Summary.Geology.

Jan 1, 1950

In late 1989, first-pass reconnaissance exploration delineated a 4km x 6km geochem- ically anomalous area centred 10km WNW of Kainantu in the Eastern Highlands Province at 6¦13'S and 145047'E. The area, named the Basangka prospect, lies between 2 200 and 2 400m asl. Interest in the area was prompted by a 14ppm Au assay of a silica-pyrite breccia float sample taken near Henkai village. The prospect was defined after several acid-leached silica- pyrite breccia and comb textured quartz float samples returned assays above lppm Au and relatively high Ag. Very encouraging and anomalous Au values were obtained from panned concentrates, despite the absence of visible Au colours. Several pan concentrates returned greater than 1mg Au and it is believed that the Au occurs as inclusions within iron oxides which were originally pyrite. In this early stage of prospect exploration, any Au value above 0.lppm in- 150# fraction stream sediments is treated as anomalous. Rock chips, panned concentrates and -150# fraction geochemistry all vividly define the areas of interest at Basangka.

Jan 1, 1991

Mt Waruwari, host to the Porgera underground gold mine in the Highlands of Papua New Guinea (PNG), is a prominent ridge of sediments and dioritic intrusives rising approximately 600m above the surrounding valley floor. Consequently, mining occurs in a low stress environment where structural and material considerations are foremost in the design of ground support and reinforcement. Three major rock types are encountered in the underground mine. These are locally referred to as "black sediments" (slightly indurated mudstones and clayey siltstones), "altered sediments" (derived from black sediments by thermal metamorphism), and "intrusives" of dioritic composition. The rocks are moderately to highly fractured, the black sediments being generally weak and occasionally sheared while the altered sediments and intrusives are quite strong but often brittle. Mining takes place from a series of stopes extracted by either slot and mass blast or a modified vertical crater retreat method (VCR), which are backfilled with a cemented rock fill. Ground support and reinforcement has been relatively conserv- ative to date and generally relies on pattern reinforcement of all development with cement grouted "rebar" bolts and mesh, extending to pattern cable bolting with occasional mesh in stope backs. In addition there has been considerable reinforcement of stope hangingwalls in some cases. A programme of broad scale structural mapping, monitoring with extensometers, material property testing, and stress analysis has been devised to allow optimum design of ground support and reinforcement in the future. Considerable work remains to ,omplete this task.

Jan 1, 1991

[ ]

Jan 1, 2009

By Peter Faust, Jeremy Zorne, Timothy Siegel, Diane Fiorelli

Professional sport venue construction follows a very simple rule. Once the decision has been made to move the team to a new place, construction shall begin immediately, so that not more than one or two seasons pass by stuck in the old home. Such tight construction schedules require a different approach than traditional design-bid-build contracts. Design is mostly done on the fly, the construction schedule becomes a main risk factor and an early contractor involvement is desired. As specialty contractors become more and more sophisticated, owners, their construction managers or the general contractor have realized the value of ideas and modern technology they can bring to the table for a successful and fast project completion. Local knowledge and experience in a variety of solutions play a key role in the specialty contractor’s ability to provide added value to the project. This is also true for the specialty foundation contractor, who needs to understand the complexity of such modern structures from its integrate foundation, over the delicate concrete structure to a potentially fancy movable stadium roof. Not to mention all the modern high tech equipment which shall make such a place a great customer experience. His expertise shall enable him to propose the most suitable foundation element for the given ground condition and application. Rather to build what others have designed, his strength is to propose alternate concepts which will be faster and (hopefully) more cost effective. This paper highlights different value engineering (VE) input a specialty foundation contractor had on 3 major sports arena projects in California. Together with the entire team from owner to GC, including the Geotechnical (GEOR) and the Structural Engineer of Record (SEOR), the most efficient and best performing foundation solution can be found every time. But such an approach also requires the open mind of the owner to entertain last minute changes when the permit drawing set has already been submitted for approval.

Jan 1, 2018

By Gupta R. C

Syria has about 500 million ton deposit of minerals having 34 per cent iron content with alumina and silica as major impurities. Efforts were made to see the feasibility of concentration by four different methods involving washing, high intensity magnetic separation, reduction roasting and magnetic separation and acid leaching technique. It was observed that the reduction roasting with magnetic separation yields a concentrate with high iron (62.3 per cent) content without requiring water which is a scarce raw material in the region. The paper concludes that the detailed study may be made following this route to optimise the process Parameters.

Jan 1, 1999

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

By Doris M. Hyde

There were no significant changes in the mineral industries of the smaller Caribbean Islands during 1980. Imported petroleum requirements continued to erode economic gains that may have occurred in other sectors. Some relief may be forthcoming as more qualified Caribbean countries take advantage of Trinidad and Tobago's petroleum product financing program (see Trinidad and Tobago). There were no crude oil discoveries in these areas during 1980, although some geophysical testing around the British Virgin Islands and Antigua war underway. In March 1980, the Government of Antigua sold a 75% interest in the 16,000-barrel- per-day West Indies Oil Co. refinery to the Swiss Intermaritime Bank and Intermaritime Management Services for $6 million. The new refinery company is called the National Petroleum Co. Shutdown since 1976, it was originally planned for the refinery to reopen in 1980, but refurbishing has proved to be more extensive than anticipated. The reopening is now expected in 1981.

Jan 1, 1982

By M. J. Leeuwner

Computational fluid dynamic (CFD) modelling is used to research the complex flow structures that exist in a hydrocyclone. By simulation of a two phase (water and air) flow system, the internal flow and multiphase interactions are investigated. The suitability of CFD modelling as a design tool is further evaluated by examining the effect of varying device dimensions. Three hydrocyclone geometries, used in previous studies, are specified. A transient simulation approach, which employs the Reynolds Stress Model as turbulence model and the Volume of Fluid model as multiphase model, is followed. Results are validated qualitatively against experimental measurements from the previous studies. Keywords: CFD modelling, hydrocyclone, Reynolds stress model, multiphase flow

Jan 1, 2008

By Z. T. Bieniawski, José Miguel Galera, Benjamín Celada

TBM case histories from over 400 tunnel sections are analyzed presenting a comprehensive application of the Rock Mass Excavability (RME) index (Bieniawski et al.2006). The paper introduces two new adjustment factors, called the Factor of Tunnel Length and the Factor of Crew Effectiveness, which were established to represent more realistically the interaction of the rock mass characteristics, the TBM parameters and the performance of the crew operating the machine. A new correlation is provided for predicting the average rate of advance of double-shield TBMs working specifically in the double-shield mode.

Jan 1, 2007

By Frank Rieber

THE study of earthquakes long ago developed the fact that by studying the travel times of the various groups of waves from the same earthquake, as received on seismographs at varying distances, major discontinuities in the earth's crust could be reasonably well defined. Using this original discovery, and adapting the mathematical methods originally devised in seismology for determining the depth below the surface at which such discontinuities occur, other investigators were able to develop a new branch of seismology which promises to be extremely useful in extending the boundaries of our information on local conditions below the earth's surface. As an outstanding example of the applications of this work, we have the so-called "seismograph" exploration of the Gulf Coastal region, which has resulted in the discovery of a large number of salt domes, from many of which oil fields may be developed. The original seismological investigations, from which different major discontinuities in the earth's crust were deduced, as well as these later successful experiments in locating salt-dome structures, involve relatively simple problems. In each case we are dealing with surface materials in which elastic waves will be propagated with a fairly definite velocity. Under this material we have something quite different, in which the elastic waves will be propagated with a much higher velocity. The transition from one medium to the other is likewise relatively abrupt. For example, in the Gulf Coastal region the sedimentary formations have a velocity of 6000 or 7000 ft. per sec., while the velocity of elastic waves in the cap rock of a salt dome may exceed 15,000 ft. per sec. Under such conditions, delineation of the formation is a relatively simple matter, and, furthermore, there is very little opportunity for ambiguous results.

Jan 1, 1928

By Bhaskar B. Thapa

The design of the Caldecott 4th Bore, located along State Route 24 in Oakland, California, is based on the principles of the New Austrian Tunneling Method (NATM). Typical NATM initial support design practices used in Europe were adapted for this project to account for U.S. conditions and requirements, such as degree of experience with NATM construction, the prevailing contractual environment, and preferences for contractual simplicity. Key design features are: (1) support selection criteria based on ground behaviors and ground conditions; (2) a prescriptive design with allowance for support adjustments based on observations during construction; and (3) organization of support requirements into only four major support categories, while permitting some adjustment for variations in ground behaviors and conditions using a few subtypes and additional support measures.

Reliable estimation of in situ stress is a major step in the analysis and design of underground excavations in rock, particularly for evaluating the stability of underground structures to prevent failure or collapse. In the last ten years, the Western Australian School of Mines (WASM) has studied and developed an AE stress measurement technique using orientated core named the WASM AE method. It allows the determination of a representative and detailed knowledge of the in situ stress field during the early stages of a project (such as mine feasibility studies), even in areas where development access is not yet available. The method has been used for in situ stress measurement at more than 80 mine sites worldwide with over 200 individual stress measurements carried out to date. This paper describes the sample collection, sample testing and reconciliation of results for very deep measurements carried out at the Craig-Onaping mine complex in Sudbury Canada. The results constitute the deepest measurements undertaken to date at the WA School of Mines and indicate that the main principal stress is horizontal and oriented parallel to a common regional sub trend in a NE/SW direction.

May 1, 2009

By H. J. de Haan, J. van Lookeren

In view of their size and favorable characteristics, Shell's heavy-oil fields on the eastern coast of Lake Maracaibo, Venezuela — known as the "Bolivar Coast" — are obvious candidates for the application of thermal recovery methods. During the last decade various methods have been tested, such as steam drive,', steam soak and in-situ combustion.3 Steam soak was discovered as a promising production method rather accidentally in 1969, during early steam drive testing in the Mene Grande Tar Sands1 When steam erupted at the surface due to breakdown of the overburden, the injection wells were back-flowed to relieve the reservoir pressure. This resulted in high oil production rates, all the more impressive because the reservoir is unproducible by primary means. It was concluded that injection of limited amounts of steam might be a very effective method for stimulation of heavy-oil wells. To obtain information that would be more widely applicable, testing of the process was continued in the eastern part of the Tia Juana field (Fig. 1). Here even more favorable results were obtained than in Mene Grande. This created sufficient confidence to prompt a large-scale project, which was considered essential for an adequate evaluation of ultimate recovery, steam requirements, mechanical problems and economic prospects. To obtain an early answer on the ultimate recovery a fairly depleted area was selected in the western part of the same field ("A" in Fig. 1). The first steam was injected in March, 1964. This paper describes the performance until the end of 1966. The production mechanism and well inflow performance are discussed in some detail. In view of the favorable results obtained so far, steam soak operations have expanded considerably since the start of this project. Presently, five other projects are under way, of which two are about the same size as the one under discussion, with further extensions being programmed. Description of the Project Reservoir Data Shell's part of the Main Tia Juana reservoir has a proven area of 8,800 acres and an average net oil sand thickness of 130 ft. It contained an initial quantity of 2,750 million bbl of stock tank oil (STOIIP), with an API gravity ranging from 10 to 15 API and a viscosity of 100 to 10,000 cp (at 122F). As a geological unit it is known locally as the Lower Lagun-illas member of the Lagunillas formation, which is early Miocene in age. The sand bodies are believed to be distributary channel sands deposited in a lower coastal plain. Most of the channel sands have lateral and some vertical communication. The field was developed mainly in the period from 1936 to 1950. The ultimate primary recovery is estimated at 18.1 percent of STOIIP, of which 12.5 percent STOIIP had been produced by the end of 1963 from some 540 wells. By then the average pressure had decreased from an initial value of 960 to 550

Jan 1, 1970

By Patrice Favreau, R. F. Ph. D. Professor Emeritus Favreau

After Nobel invented dynamite, blasts were carried out by trial and error, without the use of equations based on the fundamental principles of Chemistry and Physics, although everyone accepted that shock waves were involved; but no equations were available to calculate their intensity. Around 1950 however, M.A. Cook proposed a procedure to calculate the thermochemistry of an explosive, and thus evaluate theenergy released during the explosion of a fully confined explosive. Some blasters then began to use theEnergy Factor; the latter, however, does not subdivide the energy into its three kinds of activities necessaryfor a successful blast, as demonstrated in 1968 by reference 2, namely i) the shock wave which weakensthe rock; ii) the stress field SS which fully fragments the rock; and iii) the release of the stress SS whichcauses the fully fragmented rock to burst out with the velocity necessary to move the rock into the muckpile. The article explains that the way to achieve a successful blast is by insuring that the explosive energy divides properly into the weakening action of the shock wave which is necessary to prevent large collar blocks and toe, and into adequate stress field intensity SS which is necessary to obtain good fragmentation size distribution at the crusher, as well as adequate burst out rock movement to achieve easy mucking.

By A. Alonso, J. Daubenspeck

In the nickel extraction process at Nicaro, Cuba, dried and ground nickel bearing laterites are reduced at 1300-1400F in multiple-hearth furnaces. Nickel is leached from the reduced ore by aeration in an aqueous solution of ammonium carbonate. Nickel carbonate is precipitated from the liquor and calcined to yield nickel oxide. The following are the more important modifications of the Nicaro process since plant rehabilitation and expansion. Ten percent increase in tonnage was achieved without decreasing the fineness of the ore by minor mechanical modifications of the grinding plant. Another five percent increase in tonnage was attained by intentionally overloading the ore prepration and leaching circuits in an effort to control cobalt extraction. Modifications at the sintering plant allowed it to handle the entire output of the expanded plant. A fifty percent increase in leach liquor cooling facilities alone provided an increase in nickel production of five percent. Stronger fresh leach liquor for increased nickel washing efficiency was obtained through improved distribution of water to the ammonia absorption towers. Advantage was taken of the reduced calcine's capability to precipitate cobalt, and modifications in the leach liquor circulation provided controlled cobalt solubility with minimum harm to nickel extraction. Several process changes at the drying plant brought about a ten percent reduction in the fuel oil consumption at this pint. Controlled air addition to the reduction furnaces' upper hearths burned formerly wasted combustibles thereby reducing oil consumption by twenty percent. The nickel extraction process successfully emplayed on the extensive but lowgrade lateritic ores of Eastern Cuba at the U. S. Government owned Nicaro plant, has been previously described in various publications. The large mine and plant operated by the Nickel Processing Corporation, located on the northeastern shore of Oriente Province, have been recently expanded to a yearly capacity of about 50 million pounds of nickel. Essentially, the operation involves open pit mining of a limonite-serpentine ore mixture containing 1.3 to 1.4 percent nickel and 34 to 38 percent iron. The comparatively lumpy, wet (25 to 30 percent moisture) ore is first dried and ground prior to chemical treatment, to which the entire 7,000 tons per day feed must be subjected. In the initial chemical action the dried and ground ore is reduced with carbon manoxide and hydrogen at 1300-1400° in multiple-hearth furnaces. The resulting metallic nickel is selectively leached from the reduced calcine by aeration in an

Jan 1, 1961

By Frank Chase

Longwall mining has gained the reputation as being the safest extraction method in underground coal mines. However, one of the most difficult tasks associated with longwall mining is moving the face once a panel is completed. Based on Mine Safety and Health Administration (MSHA) fatality reports since 1996, longwall face recovery operations have claimed the lives of 5 U.S. miners and have resulted in numerous injuries. Recovery operations can be hazardous because they involve moving large pieces of equipment in very confined spaces. They are also conducted in highly stressed ground conditions due to front abutment loads generated by panel extraction. Shield removal is the most hazardous operation during face recovery because miners are constantly exposed to the unpredictable gob edge. To protect the miners, one or more walking shields, cribbing and/or other supplemental roof and standing supports are typically employed as breaker line supports as each shield is removed. At the Harris No. 1 Mine in southern WV, mobile roof supports (MRS?s) have been used in lieu of traditional walking shields on 17 face moves since 1997. MRS?s are shield-like support units mounted on crawler tracks and are commonly used during room-and-pillar retreat mining operations. For longwall recovery, the two biggest advantages that MRS?s have over traditional walking shields are that they are remotely controlled and are highly maneuverable. MRS?s have contributed to safer shield recovery and shorter move times at the Harris No. 1 Mine. This paper will address both the safety and the operational issues associated with MRS usage during shield recovery. It will also discuss new developments, including the use of the inherently safer battery powered MRS?s, which have been recently certified by the Mine Safety and Health Administration.

Jan 1, 2007

By P J. Mienie

The Palaeo-Proterozoic Transvaal Supergroup in the Northern Cape Province of South Africa is host to the largest known resources of high-grade hematite ore on the Southern African continent. These ores are currently being exploited at Sishen and Beeshoek. Hematite occurances on the Sishen South exploration project (some 65 km south of Sishen mine), are at present the focus of an intensive investigation. At both the Sishen and Sishen South deposits, mineralisation is found within lithologies belonging to the Transvaal and Oliphantshoek Supergroups. The Transvaal Supergroup comprises a basal, carbonate platform sequence (the Campbell Rand Subgroup) overlain by thick units of banded iron-formation belonging to the Asbestos Hills Subgroup. The Asbestos Hills Subgroup is unconformably overlain by sedimentary rocks of the Gamagara Subgroup. The latter Subgroup has been correlated with the lowermost unit of the Oliphantshoek Supergroup. The Sishen and Sishen South deposits are located close to the western margin of the Kaapvaal craton and have been subjected to intensive, structural deformation. Both localities have undergone folding, faulting and thrusting. Early regional tectonism (2400 - 1700 Ma) played a critical role in the genesis and preservation of the ores from younger erosive events. At both deposits, four similar iron ore occurrences have been recognised. The ores have developed in specific depositional environments and hence display unique physical, chemical and metallurgical properties:The bulk of the high-grade hematite comprises laminated and massive ores, which are found in the upper parts of the Asbestos Hills Subgroup. The laminated and massive ores are best developed in basinal and pseudo-graben structures. Collapse breccia ores of medium- and lower-grade are preserved within deep palaeosinkholes. The sinkholes have developed within the dolomites of the Campbellrand Subgroup. Lower-grade conglomeratic and gritty ores constitute the remainder of the deposits. These ores are found in the overlying clastic succession of conglomerates, shales and quartzites belonging to the Gamagara Subgroup. Although, there are many stratigraphic and lithological similarities between the Sishen and Sishen South deposits, there are also important differences, which will impact on the profitable exploitation of the ores. The most striking contrast between the deposits is their size and geometry. Sishen mine is a single pit operation with an opencast mineable reserve of 895 Mt. The Sishen orebody is thicker, more continous and significantly larger than the Sishen South deposit. The Sishen South deposit has a potential opencast reserve of 228 Mt. It comprises a number of small and narrow, isolated orebodies, spread over an area of ¦64 km2 . There is a significant difference in grade between the deposits. On average the orebodies of the Sishen South deposit have a higher iron content (+0.25 per cent Fe), less potassium (- 0.090 per cent K2O) and less phosphorus (-0.019 per cent P). The Sishen South deposit has less interbedded shale in the laminated and massive ores. The footwall of these high-grade ores is a light-density, intrusive sill, compared to banded iron-formation at Sishen. With a proposed heavy-medium separation plant at Sishen South, the impact of dilution on product grades is expected to be less than that currently experienced at Sishen.

Jan 1, 2002

The purpose of this paper is to cover in a general way the extent, geology, quality of product, working methods and trials of the coal mining industry. of New South Wales from 1946 to the present day, with particular reference to the Western field.It must be clearly understood that any opinions expressed are those of the author and not necessarily those of the Joint Coal Board.The extent of the Western coal field at the present stage of investigation may be said to be from a few miles east of Katoomha to a few miles north-west of the township of Ulan, the total distance being 150 miles.To the west of a line from the Western Highway from Lithgow through Wallerawang, PortIand, Tyldesley, Ben Bullen, Kandos and Rylstone, there are no signs of coal except for one or two outiiers in the neighbourhood of Portland. To the east of this line the coal-bearing areas extend to the seaboard approximately 80 miles to the east.GEOLOGY AND CHARACTERISTICS OF THE COAL SEAMSThe Western coal measures belong to the Upper or Newcastle series, which have been correlated with the Sciritheru or lllawarra, and the North-western or Gunnedah measures. Being close to the margin of the coal basin the Western measures have an average thickness of only 200 ft. to 500 ft., or approximately one-half of the maximum development of the Newcastle measures. They are underlain by Upper Marine beds which in turn rest directly on Devonian rocks.

Jan 1, 1954