Search Documents

By Lawrie D. C

Finely ground beryl was decomposed by mixing with ground limestone and soda ash and heating at 900°C for 4-6 hr. The sintered mater:al was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hr. The liquor containing Be, AI, Fe and other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either by filtration or bydecantation washing.The clarified leach liquor was first treated to remove Fe+++ by contacting with a primary amine-kerosene solution in 2 countercurrent stages. The iron free liquor was then passed to a 4-stage counter-current extraction unit where it was contacted with O·5M di- (2 ethyl hexyl) phosphoric acid (EHPA) in kerosene. Under the operating conditions, 99 per cent of the Be and 7 per cent of the Al was extracted.The Be and Al were stripped from the organic phase by sodium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipitatedas Be(OH)2 by heating the alkaline solution to 90°C, the Al remaining in solution. After filtration and washing, the Be(OH)2 could be ignited directly to BeO at about 1000°C or used as a feed to further purification stages if required.A small counter-current extraction unit was operated continuously using liquor derived from the sintering and leaching stages. Dataobtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precipitate contained more than 99 per cent BeO.INTRODUCTIONIn 1958 an investigation was commenced into the recovery of beryllium oxide from beryl, as part of a programme to utilize mineral resources of South Australia. A survey of the literature indicated that little work had been done on direct solvent extraction of beryllium from aqueous liquors, so it was decided to apply the experience gained in this field in uranium processing to the current problem.Preliminary extraction tests on solutions of beryllium...

Jan 1, 1965

By J. M. Richards

For most of the 20th century optical petrography has been the primary petrological and mineralogical tool used to characterize coal. The development of quantitative SEM-based techniques, e.g. QEMSCAN®, for coal began only about a decade ago. The application of these techniques for coal lagged behind other commodities, but they are currently being developed with the aim to provide ?one complete analysis? for coal. Quantitative SEM-based techniques are supplemented by quantitative X-ray diffraction (XRD). Recent indications are that these more modern techniques cannot replace the ?standard? petrographic and chemical evaluations, but rather complement them where and when required. The great advantage of quantitative SEM-based techniques is that they are very rapid, with the result that large volumes of samples can be processed on a routine basis. This is ideal for coal type identification, since the results can be used in the creation of ?intelligent? composites. This can lead to the more speedy evaluation of coal deposits by reducing the number of samples on which detailed metallurgical and characterization test work is required, without an increase in the overall statistical error of the resource model. Coal petrography, however, remains important for the prediction of the coking characteristics of certain coals and coal products. As a consequence it is therefore important that any coal laboratory be able to produce data with confidence. This requires strict quality control and assurance protocols that adhere to international standards. Keywords coal petrography, coking strength, scanning electron microscopy, QEMSCAN®.

Nov 1, 2013

By Kim Wiwchar, Elizabeth Mbaja, Lynne Dang, Jim Furey, Anita Marks

"Suncor Energy Inc., located north of Fort McMurray, Alberta, commenced pilot scale operation using a CPT 4’ diameter flotation column in March 2003. This larger scale trial follows two previously successful flotation column bench scale tests. They included an April 2002 trial with a 2.4” inner diameter column from the University of Alberta and a 20” diameter CPT column in August 2002. The column receives middlings stream feed from one of Suncor’s deep cone separation cells and is operated in parallel with a set of WEMCO flotation cells. The recovery, tails losses, and concentrate quality are being compared between the two systems. The column, to date, has been tested with all types of run of mine ore grades. Variables such as wash water flow and temperature, sparger nozzle size and location, sparger air/water flow rates, and column residence time has been adjusted to achieve better recovery and final product quality.Used in many mineral processing applications, column flotation is primarily used for the final stage of sulphide cleaning and flotation of phosphate or iron ore. As well, mechanical cells are often used in combination with a column to retrofit an operation and to produce a cleaner product.Initial results prove that this is the first successful application of a flotation column in an oilsand application. If viable, it will be an inexpensive process for recovery of bitumen from a middlings stream and able to produce a final product suitable for froth treatment.INTRODUCTIONSuncor’s oilsand is surface mined from the Athabasca Oilsand deposit north of Fort McMurray, Alberta. The oilsand is then mixed with hot process water (HPW) and the bitumen is slurried in a pipeline. Large separation cells as shown in Figure 1 float off the bitumen product, which is then steam or static deaerated and sent to Secondary Extraction for further cleaning. The tails stream from the cell is sent to the Final Tails Pumphouse (FTPH) for processing. The tailings flotation froth product gets recycled to the separation cell oilsand feed. The tailings are pumped from the FTPH to tailings ponds. The middlings stream is drawn off the separation cell approximately 9’ from the froth overflow level. It runs down, by gravity, to the scavenger banks for bitumen recovery. It was from this stream off of the Line 6 Separation Cell that the feed to the Canadian Process Technologies Inc (CPT) flotation column was taken."

Jan 1, 2004

By Hyung-woo Kim, Sup Hong, Sung-Soo Kim, Chang-Ho Lee

A deep-seabed integrated mining system, which consists of four subsystems such as riser pipe, buffer, flexible riser, and tracked vehicles, is presented in Figure 1. In order to collect more manganese nodules, multiple tracked vehicle systems should be used in a deep-seabed integrated mining system.

Sep 1, 2014

By L. A. Melis, J. W. Rowson

"Cluff Mining operates the Phase II uranium mine and mill at Cluff Lake, northern Saskatchewan. During the Phase I operation, uranium tailings were generated by acid leaching of a gravity concentrate and high-grade ore for uranium recovery. The pre-treatment gravity process, as well as the high-grade nature of the ore, led to a concentration of gold in the tailings which justified the installation of a small circuit to recover the contained gold. The operating circuit consists of tailings repulping, grinding, cyanidation, carbon-in-pulp, gold recovery, and cyanide destruction by acidification, volatilization and re-neutralization. The process is described and typical operating parameters are provided. 1.0 INTRODUCTIONCluff Mining, a Saskatchewan partnership, is owned 20 percent by Saskatchewan Mining Development Corporation (SMDC) and 80 percent by Amok Ltd./Ltee. (Amok), manager and operator of the partnership.The current operation includes the Phase II uranium mining and milling facilities, located at Cluff Lake 700 km north of Saskatoon, capable of processing 300,000 tonnes of ore to produce about 4,000,000 lbs. U308 (1500 tonnes of uranium) per year.The Phase I operation was initially established to process the very high grade ""D"" uranium orebody from 1980 to 1983. The leach tailings from the operation Phase I mill operation were found to contain elevated levels of gold. These high gold values were partially due to the gravity pre-concentration step included in the uranium recovery circuit, and to the naturally high levels of gold associated with the uranium mineralization in the ""D"" orebody."

Jan 1, 1988

By Charles Pretorius, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge.

Jan 1, 2006

By F. E. du Plessis

"The distinction between data suitable for process control and data subject to aliasing only becomes quantifiable with the availability of rapid real-time measurements. Expecting the dynamics of flotation to vary for different ore types, process flows and equipment types; a study was conducted to compare the dynamics of different flotation processes. The results shed light on the critical sampling intervals required for process control which in turn allows process stabilization and optimization. The technology used for the in-line measurements is based on diffuse reflective spectroscopy and has been introduced into the mineral processing industry over the past ten years. It has been widely implemented in the sulphide flotation industry in South Africa for the real-time measurement of grade.BACKGROUND AND OBJECTIVE A study was conducted by Du Plessis and Keet (2010) to quantify the minimum sample frequency required for grade and/or impurity control. The study was based on chromite data collected at 15 second intervals from the concentrate line of a flash float cell in the Platinum industry. The data captured the natural process variation of the entrained chromite through water recovery due to changes in feed parameters and flotation performance. It was found that the minimum rate of sampling required from the studied flash float concentrate was 2 minutes. This sampling interval time accounted for 90% of the variance in the process data. It was further found that a sampling interval time of longer than 4 minutes produced data with no significant correlation to reality. The dynamics of the flotation process has been misjudged in the past but can be quantified with the availability of real-time grade measurement based on diffuse reflective spectroscopy. The objective of the study was to compare the dynamics of different sulphide flotation processes through the comparison of maximum sampling interval times required to combat aliasing. All data were collected from single stream analyzers that are currently installed at mineral concentrators. The technology used is based on diffuse reflective spectroscopy."

Jan 1, 2012

By Albert Zima

ACCORDING to recently published statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet.

Jan 1, 1935

By Nikolaus Schneider

"Abstract: The combination of failure in joints of diaphragm walls and their exposure to water pressure may have far reaching effects ranging from water leakage to the risk of catastrophic loss of stability for the retaining wall and civil structures behind it. Investigations of imperfect joints in diaphragm walls have led to the development and testing of a quality tool to monitor the joint integrity of diaphragm walls during construction. By applying independent mechanical sensors (“joint inspector”) to the steel frame of hydraulic or mechanical grabs, it is now possible to record the surface conditions of exposed primary joints during the construction of secondary panels. This allows for the implementation of corrective action during the construction process should joint quality not indicate a watertight connection to the adjacent panel. The joint inspector, used for different types of stop ends, was tested on a full scale test field at several construction sites. The implementation of this new quality tool drives a new quality standard for deep excavations in inner city areas.General introduction to diaphragm wallsDiaphragm walls are reinforced concrete elements constructed using bentonite slurry to temporarily support an open trench in the ground. They are used in two main fields of application in civil construction, as foundation elements for vertical and horizontal loads (barrettes) and as retaining walls for excavation pits.Particularly for deep excavation pits in inner city areas, diaphragm walls are used as temporary or permanent walls of retaining walls. Alternative retaining wall systems would be secant pile walls, sheet piles or soldier piles, but these have disadvantages in structural strength when compared to diaphragm walls. If the vertical load of existing buildings next to the excavation pit has to be accommodated, the most practical solution can be found using diaphragm walls supported by prestressed anchors, steel struts or slabs."

Jan 1, 2014

By Tara Bajpayee

Modern, highly productive underground mining operations need to assure the safety of their workforce by understanding where major strata fractures and roof failures could occur. Mines depend on a host of tools to assess ground instability. In-mine microseismic monitoring systems with sufficient number of sensors have also been used to provide this information. These in-mine systems must be robust in design and moved regularly to keep up with the mining advancement. System performance issues depend on maintaining ever increasing cable runs, preventing component damage from mining activities (scaling, blasting, etc.) and avoiding signal degradation due to interference from mining equipment (fans, trucks, electrical equipment, etc.). A potential solution is to use a surface based monitoring system having sensors placed in boreholes above and adjacent to the underground mine workings. These sensors must be capable of detecting and locating strata fracturing associated with rock failure events. A great advantage of a surface based monitoring system is its independence from the underground mine infrastructure. There is less concern with cable maintenance problems, signal degradation by interference from mining activity, or loss of power from the mine?s power grid. The disadvantages include the cost of drilling boreholes and challenges associated with placing sensors in the boreholes, maintaining radio communication and solar power, and public interference (vandalism, etc.). This paper describes a case study where a surface based microseismic system, using triaxial geophones in boreholes drilled from the surface, was deployed at a large limestone mine. The system was operational during a roof fall that occurred in October 2007. It detected the first rock fracture event 17 minutes before the rock fall event. The geophone array was sensitive enough to identify all large rock fracture, impact, and blast events as well as medium size rock fracture events occurring close to the geophone array.

Jan 1, 2008

By Circadian Technologies

Alertness levels naturally fluctuate during the day and night Basic functions ??digestion, body temperature ? follow predictable 24-hour patterns Adjustment to night work creates health challenges for shiftworkers Performance decreases during overnight and post-lunch dip hours Fatigue supercedes training & experience Fatigue is a major cause of human error

Jan 1, 2010

By Michael Lenz

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels. The predictive program was initiated on the P&H Model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Feb 24, 1997

By Alan J. Zeni

Drainage of water from abandoned underground mines has become important in recent years because of safety concerns when mining near abandoned works or reentering abandoned mines for further development. Seepage from inundated mines causes environmental damage and may threaten homes and communities. Where topography permits, horizontal drilling can provide a quick and cost effective method for solving trapped water problems. The mechanics of the horizontal drilling operation as applied to water drainage are discussed in this paper.

Jan 1, 1990

By R. J. Brison, W. C. Bleimeister

The International Salt Company has long been interested in finding an efficient process for the removal of impurities from rock salt, and particularly from the rock salt produced at the Detroit mine. Methods which have been used previously at the Detroit mine included both hand sorting and differential crushing in a Bradford breaker with rejection of the oversize. Neither of these methods was adequately effective. The development of a new process for removal of impurities from rock salt has been described in the preceding article." Basically, the process consists of exposure of crude rock salt to radiant heating which selectively heats the impure particles. Subsequently the heated particles are removed by adhesion to a heat sensitive-coating on a conveyor belt. This method was found to be effective in improving both the quality and appearance of rock salt by the rejection of the dark, impure particles. The first commercial unit employing the new thermoadhesive method of dry separation of minerals was installed at the Detroit mine of International Salt Company in Detroit, Mich. (Fig. l). This unit was first put into operation in March 1957. The purpose of the Detroit installation was 1) to serve as a pilot plant for evaluating the process on a commercial scale and 2) to produce marketable quantities of rock salt of improved quality and ap- pearance. The design of this plant was based on the results and information obtained from a 1-tph pilot plant at Battelle Memorial Institute. DESCRIPTION OF PLANT Location: The separation plant was installed underground near the crushing and screening plant, for this was the most suitable location from the standpoint of material handling. Furthermore, ample space was availabe at this location. Because the process requires a relatively constant temperature, the uniform year-around temperature of the mine (57°F) gave an added advantage to an underground operation. Feeding: The rock salt is conveyed to a surge bin, from which it is fed to the heating unit by a conveyor. The feed-rate control consists simply of an adjustable gate at the bottom of the surge bin. The plant may be fed either No. 1 grade of rock salt (0.279 to 0.375 in.) or No. 2 grade (0.375 to 0.500 in.) with a maximum input capacity of 500 tons per 15-hour day. Heating Unit: The heating unit (Fig. 2) consists of a panel of infrared lamps suspended inside a low-speed revolving screen. The radiant-heat panel, which is curved for most effective utilization of the heat, holds 240 infrared lamps of standard industrial type, each rated at 500 watts. The position of the panel is adjustable so that it can be placed centrally over and to within 6 in. of the salt bed on the screen. The entire heat panel is suspended by rollers in ¦ R. J. Brison and O. F. Tangel: Development of a Thermo-adhesive Method for Dry Separation of Minerals.

Jan 1, 1961

Measurements from an old survey are being machine processed as a pilot project in the development of a computer-assisted method of structural mapping in shield areas. The key element in the system is a field data sheet which requires the geologist to determine a textural hierarchy in each exposure. The pilot system is limited to orientation analysis and utilizes a prior textural analysis, but this would not usually be a problem in utilizing the system ab initio for exploration. A data processing system of this general type offers promise of considerably increased productivity of field geologists by reducing compilation time and improved technical supervision through centralization of processing, and would make structural analysis an economically viable tool in mining exploration and development.

Jan 1, 1969

By David M. Jurich, Randy J. Essex, Alex de Aboitiz

An Automated People Mover (APM) transit system is planned for the growing Phoenix Sky Harbor International Airport. The APM will improve passenger movements between the terminals, and provide a link to parking facilities, a new rental car facility, and the planned metro Light Rail. The underground works will include shallow twin bored tunnels, taxiway crossings, and underground stations constructed beneath critical airport facilities. Challenging soft ground conditions will require extensive underpinning and ground improvements. Design is underway, and construction is scheduled to begin in 2007 with project completion in 2015. The owner’s planned delivery method for the APM Project will be Construction Manager at Risk (CMAR) with a Guaranteed Maximum Price.

Jan 1, 2005

By Charolett Hayes, A. L. Russell, Anthony J. Bednar, Jared Smith, Valentine A. Nzengung, Stephen L. Pilcher

The manufacture of Energetics Materials (EM), including maintenance and demilitarization of munitions causes dangerously high levels of explosives residues to be harbored in building features. The two commonly approved methods of decontaminating energetics contaminated equipment and building features are thermal treatment and steam washing. The current regulatory environment is generally becoming more stringent and unfavorable to thermal and steam decontamination because of their adverse impact on air, soil, and water and their ineffectiveness to completely remove accumulated energetics from foundation cracks, internal and external piping, voids in walls and ventilation systems, and internal cavities of fixed equipment. However, chemical destruction of energetics, especially high explosives, is gaining acceptance as a safer, cost-effective and environmental friendly alternative to thermal and steam decontamination. Organic explosives, including nitramines and nitrate esters are oxidized organic compounds that are susceptible to chemical oxidation and reduction reactions. Under suitable conditions, a chemical reagent consisting of sulfur-based bulk reductants (neutralent) commercialized as MuniRem generates highly reactive free radicals that very rapidly degrade many energetic compounds to innocuous end products while stabilizing metals as the insoluble metal sulfides.

Jan 1, 2016

By C. A. Young, J. D. Miller

The surface chemistry of the calcite/oleate flotation system was examined by in-situ FT-NIR/IRS. Spectra of combination and overtone bands of aliphatic stretching vibrations revealed gauche/trans conformational changes that occurred solely as a function of temperature. The conformational changes were attributed to the simple "melting" behavior associated with phase transitions. It was concluded that chemisorbed oleate at calcite surfaces is gel-like at temperatures below 22oC, resembles a coagel between 22oC and 31oC, and becomes micelle-like at temperatures above 31oC. By comparison, chemisorbed oleate at fluorite surfaces also undergoes these phase transitions but is additionally dependent on adsorption density. The conformational changes were observed at high chemisorption densities (> 2.0x10-10 mol/cm2) and attributed to molecular forces, primarily van der Waal's interactive forces, among neighboring chemisorbed oleate molecules. Similar analysis of in-situ FT-NIR/IRS spectra of surface-precipitated calcium dioleate at calcite surfaces did not exhibit this behavior thereby confirming that surface-precipitated calcium dioleate remains in an all-trans conformation. The results help explain why surface polymerization is not observed at calcite surfaces but is observed at fluorite surfaces.

Jan 1, 2002

By Petrus Christiaan Pistorius, Makunga Daudet Seke

The flotation response of a Pb-Zn sulphide ore from the Rosh Pinah Mine (Namibia) was studied in the presence of inorganic depressants such as sodium cyanide and zinc sulphate. Poor flotation selective was observed in the rougher concentrate of the galena circuit despite the use of excessive amount of sodium cyanide. Batch flotation tests have shown that the use of cyanide alone is not efficient for the depression of sphalerite from the Rosh Pinah ore when milling is carried out according to the current plant particle size distribution. The use of both cyanide and zinc sulphate improved the selectivity between galena and sphalerite much better than cyanide alone. Flotation selectivity is limited by the mineralogical texture of the Rosh Pinah ore sample. Microscopic analysis has shown that the presence of sphalerite in the galena concentrate is also due to poor liberation between galena and sphalerite, especially in the middlings. Hence selectivity could be improved by regrinding the rougher concentrate prior to the cleaning stage. Keywords- Sulphide ores, Flotation, Flotation depressant, Mineralogy.

Jan 1, 2005

Bubble Load Measurements in Flotation - A Critical Review of Current Practice

Sep 13, 2010