Search Documents

By C. W. Huggins

The primary objective of this Bureau of Mines research was to measure the size distribution of respirable quartz collected at metal mines, nonmetal mines, and processing plants to select the best reference standard for use in quantifying quartz in mine and plant dust samples. The secondary objective was to size all the nonquartz particles collected at the same sites. Particle size measurements were made on 29 samples using a scanning electron microscope in the backscatter mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration, Denver, CO, provided the 29 samples, which were collected at mines and processing plants in 19 states. The accumulated particle size measurements indicate that NBS 1878, minus 5-f.lm Hin-U-Sil, and minus 5-f.lm Supersil would be preferred over Silver Bond B as reference standards for most quantitative determinations by X-ray diffraction and infrared spectrometry. The respirable dust samples collected at sand plants, however, would be better served by a new reference standard having a quartz particle size distribution of approximately 2.2 um, as none of the four existing reference standards matched closely with them. Commercially available NBS 1878 and minus 5-um Hin-U-Sil CQuid be used as reference standards for 28 of the 29 samples studied in this investigation.

Jan 1, 1986

By S. Que

Local community acceptance is a key aspect of planning and managing mining projects, whether through sustainability assessment and reporting or corporate social responsibility programs. However, there has been very little research to understand the determinants of community acceptance. This paper seeks to identify key mine characteristics and demographic factors that influence individual acceptance of mining projects. Six demographic factors and 16 mine characteristics were selected based on literature review. Four of the six demographics factors were confirmed to be significantly (p < 0.05) correlated with people?s attitude of the importance of the mine characteristics. All sixteen mine characteristics are identified as important factors. The most important mining factors are Job opportunities, water shortage or pollution, air pollution and land pollution. Both the mining and control groups have same opinion of 12 mining characteristics and differ on four (infrastructure improvement, labor shortage for other businesses, noise pollution, and mine life). During design and management of mines, this data can be used as a reference. This result will facilitate better choice experiment (survey) design for discrete choice modeling. Such discrete choice models can provide a viable framework for data-driven community engagement and sustainable mine management.

Feb 23, 2014

By A Hall, D Kratochvil, P Littlejohn

Economic recovery of gold from complex gold ores, including poly-metallic deposits, is impacted by the presence of cyanide-soluble base metals. These base metals can create both a metallurgical challenge plus waste handling and disposal challenges. Base metals such as Cu and Zn compete for the cyanide reagent and often increase the total cyanide consumption to the point of making precious metals recovery uneconomic. In addition, the accumulation of base metals in cyanide solutions represent a challenge for cyanide detoxification and waste water treatment as these metals report to waste sludge. Such sludge requires safe handling and disposal, with possible long-term liabilities.Base metal interference can be removed with sulfidisation-acidification-recycling-thickening (SART) process technology. SART liberates the base metal from the cyanide complex and precipitates the metal as an insoluble sulfide product that can be recovered as a commercial grade concentrate. With the base metal precipitated, the cyanide can be regenerated as free cyanide and recycled to the gold extraction circuit.BioteQ completed laboratory testing for two projects, one employing cyanide leaching of copper-gold sulfide flotation concentrate and one employing a Merrill Crowe process, to determine the effectiveness of SART to remove and recover Cu and Zn in high-grade sulfide concentrates and to reduce the impact of cyanide-soluble metals on gold recovery and cyanide consumption. This paper will provide an overview of the testing methodology and results along with a review of the potential for SART to be applied to complex gold ores with poly-metallic deposits to improve project economics, operability and waste management.CITATION:Littlejohn, P, Kratochvil, D and Hall, A, 2013. Sulfidisation-acidification-recycling-thickening (SART) for complex gold ores, in Proceedings World Gold 2013 , pp 149-156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By F. E. Joyce

The Bureau of Mines studied copper-nickel minerals (mainly sulfides) of the Duluth Gabbro Complex in north-eastern Minnesota to determine their response to selective high-temperature sulfatization techniques. The gabbro, containing 0.44 percent copper and 0.13 percent nickel, was ground to minus 325 mesh and sulfatized in a heated, rotating, stainless steel bench-scale retort. Tests demonstrated that over 95 percent of the copper and 80 percent of the nickel can be converted to water-soluble sulfates, depending upon the roasting conditions employed. Yield equations were developed using regression analysis for predicting the extraction of copper and nickel between the temperature limits of 520° to 670° C, the roasting time limits of 3 to 7 hours, and S02 limits of 10 to 40 percent in S02-air mixtures.

Jan 1, 1971

By Vincent A. Scovazzo

"The most significant study on the effects of longwall mining on gas and oil well integrity was completed by a consortium of coal and shale gas industry participants. A field study was conducted in 2013 and 2014 and is referred to by its location on Well Pad NV-35. The experiment site was located at the CONSOL Enlow Fork Mine in Washington County, Pennsylvania.The experiment was completed to verify John T. Boyd Company (BOYD) calculations and studies completed under contract by for the Pennsylvania Department of Environmental Protection Gas Well Pillar Study Update. The findings of the original study were presented by BOYD at the 32nd Conference, while numerical analysis of the Well Pad NV-35 field study was presented by Dr. Su at the 35th Conference.This paper addresses the findings of the experiment and how it confirmed the conclusions of the original study.INTRODUCTIONA field study was conducted in 2013 and 2014 by a consortium of coal and shale gas industry members to test the effects of longwall-induced ground movement on the stability and integrity of wells drilled through a gateroad abutment pillar. The project was initiated to test initial John T. Boyd Company (BOYD) findings of the Gas Well Pillar Study Update (Scovazzo and Moran, 2014), completed for Pennsylvania Department of Environmental Protection, Bureau of Oil and Gas Management (PDEP). Background and initial findings on this project were presented at the 32nd Conference (Scovazzo and Moran, 2012). The field work and numerical analysis were spearheaded by CONSOL Energy, Inc. (CONSOL) with participation by Chevron, EQT, Noble Energy, Range Resources, Marcellus Shale Coalition, and the Pennsylvania Coal Alliance.Dr. Wen H. Su of CONSOL was the leader of the field experiment with input from the participants. Dr. Su also completed numerical analysis of the results and model casing deformation. Analytical results were presented by Dr. Su at the 35th Conference (Su, 2017)."

Jan 1, 2018

By P. Amelunxen

Over the past several years, the combination of higher energy and steel costs and the recent commercial deployment of high-pressure grinding rolls (HPGR) technology in hard rock mining have led many multinational mining companies to evaluate the suitability of HPGR technology for their particular comminution circuits. HPGR technology is perceived to require a higher capital investment while delivering lower long-term operating costs. This paper undertakes a critical evaluation of this perception. By evaluating the capital and life-of-mine operating costs of competing circuit designs for soft, medium and hard ores, the HPGR break-even point can be identified, at which the incremental capital cost of an HPGR circuit is equivalent to the net present value of the projected operating cost reductions. For ores with hardness parameters above the break-even point, HPGR circuits could offer economic benefits, while for softer ores, SAG mill/ball mill/pebble crushing (SABC) circuits are likely to be more economical and energy efficient. This evaluation considers both an SABC reference circuit and a traditional stage crushing configuration. Other influential factors are also discussed.

Jan 1, 2011

By David K. Fountain

"The growth of the mining industry in British Columbia in the last ten years has been largely the result of the development of large low-grade copper and molybdenum deposits. There are two problems which must be solved in the search for mineral deposits of this type. It is necessary to detect large volumes of rock containing a low percentage of total sulphide mineralization1 and, secondly, to get some idea of the economic significance of this mineralization. The standard geophysical exploration techniques available have a varying degree of application in the search for disseminated sulphide de-posits. The electrical methods, and the induced polarization method in particular, are the most successful direct methods, and magnetic methods have indirect application in most situations. This is illustrated by geo-physical survey results from several properties in British Columbia."

Jan 1, 1968

By Arthur B. Johnson

The Bureau of Mines investigated the concentration characteristics of high-clay sylvinite ores from four potash companies operating in the Permian Basin near Carlsbad, N. Mex. These ores, containing 13 to 22 percent K20 and 3 to 7 percent clay slimes, cannot be effectively processed by current commercial flotation methods because of their high slime content. A solution to this problem was shown to be the use of two-stage moderate scrubbing conditions and washing of the ore as opposed to strenuous attritioning. Bench-scale physical beneficiation techniques for recovering potash minerals and the development of ore-dressing systems by flotation resulted in obtaining acceptable product grades and recoveries. By using a coarse grind, emphasis was placed on production of premium granular and coarse products. Flotation results showed that concentrates of 58.7 to 60.4 percent K20 with recoveries of 71.0 to 83.4 percent 0f the K20 values can be obtained.

Jan 1, 1971

By S. Iverson

Fall of ground accidents continue to be a source of injury in underground metal mines. MSHA accident statistics indicate that most rock fall accidents occur at a new face where drilling and blasting methods are used. Removing loose rock by scaling is imperative to removing the potential for rock fall injury. Detection of potentially loose rock could improve the scaling process and result in fewer rock falls. Infrared thermal imaging cameras were investigated as far back as 1966 as a tool for loose rock detection. Early on it was clear that sensitivity (e.g. detectable temperature increment) is a key factor in this application. Both pixel resolution and temperature resolution have greatly improved with modern instruments. This paper describes an evaluation of modern infrared thermal imaging camera technology to detect loose rock conditions at six underground metal mines in the western U.S. It was found that thermal images provide a high resolution visual discrimination between loose rock and intact rock. However, detecting loose rock was difficult in cases where the rock and ventilation air were at the same temperature. Loose rock was detected when rock was both warmer and cooler than the ventilation air temperature. Warm rock with cool ventilation air provided the best conditions for detection.

Feb 23, 2014

By Thomas E. Finch

Engineering mine design encompasses a range of situations, and each situation has its own range of detail and fineness. The most time consuming, and perhaps repetitive design situation involves evaluation of new or alternate mining methods. Many man years are consumed examing alternatives conjured up at all levels of the design team, from the number crunching engineer to the engineering manager. Many alternatives are intuitively disregarded, some are briefly evaluated and thrown out, and many others are started but not completed due to time constraints. All alternatives have similar input characteristics and evaluation procedures. In the design process, production requirements are known and equipment production capabilities are generated to determine the numbers and costs of an equipment type required to match a given situation. The end result is some comparative figure, typically cost per ton or yard upon which a decision is built. The similarity of input data and problem solving techniques lends design to computer solution. Computer aided equipment evaluation is not new to the mining industry. An existing and accepted technique is exemplified with the programs used by truck manufacturers. Given a haulage profile and production requirements, the number of anyone capacity, horsepower, tire size, gear ratio or similar characteristically identified truck can be determined. This information can be outputted in varying degrees of complexity and the results used with equally varying percentages of credibility by design or production engineers. Most engineers are willing to accept-the computer&apos;s effort with relief and a desire for belief. Although inherently more complex, the ultimate end of computer manipulation should be total mine design. This is an extremely large step in the evolution of mine design, and not many engineers, including the authors, believe the results would be directly applicable or necessarily correct. As with computer simulations of an operation, total computer design of mines requires such complex and lengthy input that each mine might be manually designed more quickly and cheaply. The existence of computer programs which initially evaluate a mining system or part of the system is upon us, however.

Jan 1, 1978

By P Jackson, J Rea, M D. Goodz

The Morning Star Gold Mine has operated over a 101-year period, producing gold from narrow quartz veins and sulfide stockworks hosted mainly within a dioritic-gabbroic dyke. The deposit has been developed over a vertical depth of 980 m with drilling extending the vertical depth to greater than 1200 m. Currently there is a total Inferred Resource of 4.6 million tonnes at a grade of 6 g/t for 910 000 ounces of contained gold resources, which comprises an underground project and a surface project. Significant variation exists between the grade of drill core intersections and that observed in face sampling and subsequent production reconciliation (250 - 650 per cent). Studies were carried out on ten major production reefs, where the grades of drill intercepts were compared with face samples collected during development and mining. The implications of this study have been used as justification to assign production or stope/development grades where applicable to resources that are direct extensions of the historical development headings. Grade assignment and its impact on sensitivity for gold resources are detailed and show a 40 per cent variation in the gold resource, depending upon whether a production or calculated stope grade is used in grade assignment for the major reef deposits. Recent diamond drilling has intersected approximately 40 new gold bearing quartz reefs and sulfide zones that contain all the key mineralogical and structural indicators, and traditional large variations in gold grades similar to the historical major production zones. The implications of grade factoring and grade assignment are the greatest challenges confronting the resource estimation team in defining grade for these new zones. Grade assignment is seen as a method of balancing known historical production observations with the irregular grade distribution inferred from drill core assay results. Ongoing mine development and bulk sampling works are planned to validate the grade assignment process. The first stage of this process is the trial mining of the newly discovered Maxwell Reef (MR). The stope drawpoints were completed in August 2008 and the MRS1 stope is scheduled for completion in September. The stope reconciliation results will be presented at the October 2008 conference.

Jan 1, 2008

By Craig M. Sams

Matching mill? drives to mill power draws is a relatively new practice with the introduction of variable speed drive arrangements. Semi-autogenous grinding (SAG) mills are the focus of this paper as ball and rod mill characteristics are easily charted as charge loading and speed change. In addition, a look at types of drives available in the market and mechanical ratings is outlined to match the specifics of each drive.

Jan 1, 1991

By Marius R. Campbell

Does mine-sampling show the commercial value of a coal, and if so, how should it be done? This question is often asked, but seldom answered. During the past summer, while engaged in securing coal for the Government coal-testing plant at St. Louis, I had an excellent opportunity to obtain information on this subject, and the results seem to furnish an answer to the questions propounded above. Sampling for the Geological Survey Coal-Testing Plant. In organizing the work of the testing-plant, it was decided that coal in car-load lots only would be accepted for testing, also that this coal should be loaded under the immediate supervision of a representative of the plant, so as to be certain that the car-load sample would be representative. As an additional check on the work, two mine-samples were to be collected from each mine visited, and these samples, as well as the sam¬ple from the car when it was received at the testing-plant, were to be carefully analyzed at the chemical laboratory, which was established in connection with the plant and operated under the direction of Prof. N. W. Lord, of the Ohio State University, Columbus, Ohio. Mine-Sanmhling:-Mine-samples were collected with great care by me and my assistants, Messrs. J. Shober Burrows, John W. Groves and Frank W. De Wolf. The dominant idea in the regulations which were adopted for mine-sampling was that it should be done in such a manner that the sample would have the same composition as the commercial output of the mine. .

Sep 1, 1905

By Seth H. Hamblin, Leo J. Hart, John E. Regan

The Route 6 /10 10 Interchange Design/Build project, located in Providence, Rhode Island, involves the design and construction of five (5) new elevated bridge structures to replace and reconfigure the existing interchange and to provide a link between Route 10 northbound and Route 6 westbound. Due to site logistics, headroom restrictions, and depth to bedrock, 50 ton drilled micropiles installed in the deep medium dense sand strata were initially proposed as the deep foundation solution. Post project award, Geosciences Testing and Research, Inc. (GTR) performed various analyses and developed an alternate driven pile solution using steel Tapertube. The results of these analyses indicated that driven steel taper tube and steel pipe piles could develop greater capacities than the drilled micropiles in the granular soil layer, thereby reducing the number of foundation elements, decreasing construction schedule and providing a more cost effective foundation alternative. A comprehensive driven pile load test program was subsequently executed by GTR and the Design Build Team led by Barletta Heavy Division of Canton, Massachusetts, to assess the performance of Tapertube and steel pipe piles, including pile drivability, load-deformation characteristics under static and dynamic loading, and to develop site-specific design parameters in two (2) distinct test areas. The test pile program included dynamic, static compression, tension and lateral load tests on each test pile. Load test measurements were automated with embedded Vibrating Wire Strain Gages (VWSG) to measure load transfer with depth. The execution and results of the successful pile load test program are presented and offer unique case study and valuable data for the use of Tapertube piles on deep foundation projects in the New England region INTRODUCTION The Rhode Island Department of Transportation (RIDOT) Route 6 / Route 10 Interchange is located west of downtown Providence. Originally constructed in the 1950’s as a highway bypass around the historic Olneyville neighborhood, the interchange consists of a series of nine (9) bridges and ramps that serve as a vital east-west link between Interstate 295, 95 and 195. Based on recent bridge rating assessments, seven of the nine bridge structures are rated “structurally deficient”. With many bridge structures shored with temporary supports as many as 15 years ago, the interchange is in critical need of replacement. In 2018, RIDOT awarded the Route 6/10 Reconstruction Design-Build Project to 6/10 Constructors, Joint Venture. Led by Barletta Heavy Division of Canton, Massachusetts, the Design Build team includes O&G Industries, DW White Construction, Aetna Bridge Co. and AECOM. The scope of work includes the replacement of the bridges and ramps, and will provide direct access from Route 10 northbound to Route 6 westbound. Valued at over $400M (US), this is currently the largest project awarded in RIDOT history.

Jan 1, 2019

By Hemraj Dangi, S. Murali, Bhisham Yadav, Mohini Saxena, P. Asokan

"Demonstration studies were carried on the use of fly ash as soil modifier and supplier of micronutrients to improve the agricultural productivity based on the process optimised at lab scale at Advanced Materials & Processes Research Institute, Bhopal. The field trials were conducted in Uttar Pradesh (North India) Orissa (South Eastern India) and Madhya Pradesh (Central India) under different soil and crop conditions. 100-650 tonnes of fly ash per hectare were applied depending upon the soil and fly ash characteristics. Both short and long term studies on impact of fly ash on soil and food quality were conducted. With the fly ash application, the edible yield of tomato, cabbage, potato, wheat, pea, onion, paddy, sunflower, maize etc., were increased from 12 - 46% as compared to the control soil where no fly ash was used. The crop response to various elements mainly heavy metals grown in soil and fly ash applied soil was found comparable to that of control, which are within the permissible limits and meet the food quality standards. The results of impact of fly ash on biotic and abiotic properties of soil, along with the quantity and quality of agricultural produces generated under pilot scale demonstrations in three different parts of India are discussed in this paper. The outcome of this work could act as guiding force for confidence building and to maximise the use of fly ash, generated from thermal power plants worldwide as one of the major mineral waste for agriculture purposes.IntroductionThe advantages of application of fly ash in terms of improvement of soil properties and crop yields have been published by various researchers in India and abroad. Attention is also given about the possible negative and beneficial impact of pond ash in agriculture due to presence of heavy elements, radioactive nuclides and plant nutrients in fly ash. It is evident from the analysis of Indian fly ash that the presence of heavy elements and radionuclides levels are comparable with normal soil. The positive impact that has been reported is with regard to germination, yield and crop growth. The significant impacts are: long term effect of heavy and toxic elements content of fly ash on soil and up take of these elements by plant. Pilot scale demonstration studies have been completed with varying soil crop-combination under different agro-climatic conditions showed considerable improvement in the productivity of cereals, oil seeds and vegetables."

Jan 1, 2008

By I. O. Flores, A. Anani, H. Li

Current technological advancement has increased the exploitation of deeper ore bodies using underground methods. In certain cases, the mineral deposit starts near the surface and continues deep within the earth's crust. Such deposits are best mined with both underground and surface methods. Two main techniques are used to determine the optimal transition depth from surface to underground - a disintegrated approach and an integrated approach. Both methods have limitations in their use to determine the optimal transition depth. The objective of this research is to investigate the conditions in which an integrated approach to the transition depth problem is superior to a disintegrated approach. Three binary integer linear programming models are developed for this purpose: a surface and underground model for the disintegrated instance and an integrated model. A case study is performed to validate the models, with a comparative sensitivity analysis to obtain operational insights.

Sep 1, 2021

By B Darlington, L Sandberg, O Vallati

The D47 and D39 Mechanical Dynamic Extra bolts (D47 MDX and D39 MDX) have been developed in response to the ever-increasing demand from the mining industry for rock bolts with high dynamic capacity. To prove such capacity, Sandvik has performed numerous in situ dynamic testing with the unique Dynamic Test Rig (DTR) (Darlington, Rataj and Roach, 2019; Roach, Rataj and Darlington, 2019). To complement the collection of testing data, Sandvik, in collaboration with the Swedish Research Institute for Mining, Metallurgy and Materials (Swerim) have performed additional experiments in laboratory condition using Swerim’s new drop test rig. This rig utilises a momentum transfer method to apply a dynamic load to the bolt. The sample falls together with the mass until the support beam impacts stationary dampers and the momentum energy is transferred to the bolt. Part of the charged energy is released by the dumpers while the remaining portion is absorbed by plastic deformation and/or displacement of the ground support element. The D47 and D39 MDX bolts have been tested at Swerim’s test facility with different levels of input energy. Six tests were performed at the specification energy of 36 kJ and six tests were carried out with the maximum allowable energy from the facility, ie 44 kJ. The bolts confirmed their dynamic performance absorbing the input energy without failure. The D47 MDX bolt absorbed up to 33 kJ with 150 mm displacement while the D39 MDX bolt absorbed up to 35 kJ with 162 mm displacement. This work will present an overview of the drop test rig at Swerim’s facility and a collection of results of the test performed on the D47 and D39 MDX bolts. The test method and results will be analysed and compared to the tests carried out with the in situ DTR.

Nov 29, 2022

By Pengfu Tan

NiModel, a thermodynamic model, database and computer program, has been developed to predict the distribution behavior of Ni, Cu, Co, Fe, S, O, As, Sb and Bi, and heat balance in the nickel pyrometallurgical processes such as Outokumpu flash smelting, Outokumpu direct high-grade matte smelting, INCO flash smelting, and Peirce-Smith converting processes. In this model, as much as 16 elements (Ni, Cu, Co, Fe, As, Sb, Bi, S, O, Al, Ca, Mg, Si, N, C and H) are considered. The compositions of matte, slag and gaseous phases, and heat balance are calculated using the thermodynamic data and the activity coefficients of the components derived from the experimental data. The model predictions were compared with the known industrial data from Kalgoorlie Nickel Smelter in Australia, Outokumpu Harjavalta Nickel Smelter in Finland and INCO Metals Company in Canada, and an excellent agreement was obtained. In this paper, the applications of NiModel in the nickel pyrometallurgical industries have been presented. NiModel has been used by Jinchuan Group Limited in China.

Jan 1, 2004

By Bruington T, Perkins J, Hutton R

Natural resource developments are among the largest and most challenging projects taking place in the world. They involve capital intensive investment with long lead times and the management of geological, market, technical, operational and financial issues. A clear strategy is required to manage these projects and this strategy is underpinned by a development Philosophy.

Jan 1, 1997

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

This paper describes the general principles of the expander body with post-grouting (EBI) system, and how it is similar in nature to a large-scale pressuremeter device. The results from the installation of an EBI can be used to provide information about the stress-strain characteristics of the soil adjacent to the device and to compute estimates of nominal axial resistance. As the EBI expands during grouting, pressure is applied to the in-situ soil surrounding the device thereby compacting/densifying the soil. The nominal axial resistance for small diameter piles/ground anchors can be increased due to the greater soil stiffness and shear strength around the device, larger surface and end area, and improved soil-to-EBI interaction in side resistance. The shape of the response curves depends on the geotechnical conditions of the soil (e.g., in-situ stress state, strength, and stiffness) and the installation method of the piling/ground anchor. This technique has been used successfully with different pile types and ground anchors in a wide range of conditions from very loose sands/silts to very dense sands and medium-dense gravels as well as in soft to stiff clays. This paper also describes a mini case history in which 80 piles were installed to support an office building, and the results of the static axial compression load tests performed on a production FDP+EBI pile is also included.