Search Documents

By Fred Hodges

This paper describing the concentrator practice of the Hurley Plant of the Nevada Consolidated Copper Co. at Hurley, N. Mex., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Hurley concentrator has a normal daily capacity of 13,500 tons of ore, and for the first four months of 1930 the heads of the concentrator averaged 1.32 per cent of copper and 3.14 per cent of iron. The recovery for this period was 83.98 per cent and the concentrates produced averaged 27.54 per cent of copper.

Jan 1, 1931

By John J. Mulligan

Since 1941 the Federal Bureau of Mines has been conducting an intermit-tent program of placer and lode investigations to evaluate the potential tin resources of the western Seward Peninsula tin belt. Previous investigations were made in the Potato, Cape, Brooks (Lost River), and Ear Mountain areas. As part of this program the Bureau made a reconnaissance of reportedly tin-bearing stream gravels in areas adjacent to the previously worked tin deposits at Lost River and Potato Mountain. The objective of the reconnaissance was to determine if additional areas might be favorable for lode or placer exploration. The work was begun late in the fall of 1956 and completed during the following summer. The streams sampled were the Lost River and York Creek in the Brooks Mountain area and the Anikovik River and Kigezruk and Baituk Creeks in the York area. Samples were obtained by churn-drilling methods employing conventional placer-evaluation procedures. Holes were drilled at wide intervals at sites chosen as being representative of drainage areas rather than of individual gravel deposits. Minor to trace amounts of tin were found in the gravels of all these streams, but the highest grade was 0.35 pound of tin per cubic yard in the gravels of Lost River below the mouth of Tin Creek. Small amounts of gold were found on Baituk Creek and in one hole on the Anikovik River; the highest grade did not exceed 10 cents per cubic yard. Traces of scheelite and barite were found on York Creek, chromite was encountered in one hole on the Anikovik River, and minor amounts of titanium minerals (probably derived from basaltic intrusives) were found in the York area.

Jan 1, 1959

By K. D. Dill, S. D. Rosenthal

"This project analyzed the efficiency of incorporating the use of directional drilling technology into coal overburden blasting. Directional drilling is currently in use in the petroleum industry and it is believed that it will be a valuable asset in the mining industry. This project has shown that directional drilling can be a viable technology for use in the coal overburden removal process resulting in increased drill utilization and potential for cost savings. Future work regarding blasting and geotechnical evaluation should be performed to solidify the concept. INTRODUCTION Determine the Potential Drill Utilization Improvements and Rock Fragmentation Requirements Using Directional Drilling in a Coal Mining Overburden Highwall Application was a project funded by Atlas Copco Drilling Solutions (Atlas Copco) based in Garland, Texas. The project was developed and researched by Montana Tech of the University of Montana. This project was intended to show how the use of directional drilling can increase drill utilization, while decreasing costs, without sacrificing overburden blasting results. This paper discusses a review of the literature, the methods performed, conclusions and future work Background Atlas Copco theorized that an alternative approach to drilling a cast blast pattern would be beneficial to coal mining operations by increasing drill utilization and therefore, decreasing overall costs. Increasing drill utilization results in an increase in the amount of time the drill is being productive, more drill bit time in ground. Atlas Copco’s theory is that by incorporating directional drilling in the design of a cast blast pattern, a drill rig could drill multiple directional holes, which are the length of the cast blast, from a single drill set up. A drill goes through a series of steps to complete a blast pattern, these steps include: tramming to the hole location, leveling the drill, drilling the hole, cleaning the hole, and retracting the drill steel. This process is repeated hundreds of times until the whole pattern is completed. The most time intensive part of this process is drilling out the blast pattern. Integrating directional drilling into this process could decrease the overall time it takes to drill out a blast pattern by minimizing the amount of time spent tramming and setting up for each subsequent hole. Tramming and drill set up are two aspects of the drilling process where the drill tool is not engaged with the ground and, therefore, not being utilized. A cast blast pattern designed to utilize directional drilling will allow the drill tool to be “in the hole” longer and will improve drill utilization. This change in drill utilization was analyzed. Drilling and blasting is an integral part of the mining process, without it mining would be a slower process and less material could be mined. Drilling provides holes for explosives to be loaded and then blasted. Blasting has been found to be the most cost effective method of fracturing rock in mining for material removal. Blasting is also used as a low-cost method to move the rock in open cast mines, commonly referred to as cast blasting. A cast blast is a large blast designed to allow for the maximum amount of overburden to be removed using explosives in a single blast thereby uncovering more coal at a lower cost. Not all the material is blasted to cast-to-final, which requires that material to be moved with large mining machinery. Material that is considered cast-to-final is material that has been thrown far enough to never be moved again in the coal extraction process, therefore it is in its final resting place. A typical cast profile and cast-to-final area is shown in Figure 1."

Jan 1, 2017

By D. P. Lindroth

The Bureau of Mines is engaged in research on ground probing radars for detection of geologic hazards in advance of mining. Penetration distances and interpretation models depend on the dielectric properties and wave propagation characteristics for coal measure stratified media. Relative dielectric constants and dissipation factors were measured under ambient conditions for Pittsburgh Seam coal measure rock over the frequency range of 20 to 100 MHz by the susceptance-variation method. The rock types measured were representative sedimentary rock located above the Pittsburgh Coal Seam. Extreme values for the computed attenu-ation distance ranged from 1.7 m at 100 MHz for siltstone to 230 m at 20 MHz for a particular limestone.

Jan 1, 1984

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsater-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig. Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this typo of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

By R. M. Santmyers

"Quartz and silica not only occur in diversified forms in nature but find a multiplicity of uses in industry. The purpose of the present paper is to assemble brief summaries of the many widely differing industries engaged in the production and preparation of these minerals in their principal commercial forms. Due to the scope of the subject it was though advisable to divide the paper into three parts. Part I deals with the subject of quartz and silica in general. It also contains a flow sheet of silica from deposit to consumer (fig. 1). Part II covers the uses and other economic factors of quartz, quartzite, and sandstone, the varieties of silica found in consolidated form. Part III deals with sand and miscellaneous silicas such as tripoli and diatomite. A chart showing the major ramifications of these industries is presented herewith as an introduction to the more detailed discussion that follows.For a more intensive study of many branches of the quartz and silica industries the reader is referred especially to Bulletin 263 of the United States Bureau of Mines, Technology and Uses of Silica and Sand by W. M. Weigel. For annual statistics relative to silica and its products in the United States he is referred to the annual chapters of Mineral Resources of the United States, entitled ""Silica,"" ""Sand and Gravel,"" and ""Abrasives."" With respect to diatomite reference is made to Diatomite, by Paul Hatmaker, recently issued by the U. S. Bureau of Mines as Information Circular 6391. In preparing this paper the author has drawn freely from these sources as well as Marketing of Metals and Minerals, by J. E. Spurr and F. E. Wormser; Non-Metallic Minerals, Occurrence, Preparation and Utilization, by Raymond B. Ladoo; and Abrasives - Part I, Siliceous Abrasives, by V. L. Eardley-Wilmot, Report 573, Mines Brand, Department of Mines, Ottawa, 1927.Acknowledgment is also made to the Foote Mineral Co., which has published in Foote-Prints (vol. 2 of 1929 and vol. 1 of 1930), comprehensive reviews of the uses of crystal quartz in the optical industry and as piezo¬electric crystals.The various forms of silica have attracted attention from the earliest times, and the water-clear crystallized variety was known to the Greeks as""krystallos"" (clear ice), being supposed by them to have been formed from water by the intense cold of the Alps; hence the name ""crystal"" or more commonly ""rock crystal,"" applied to this variety. The name quartz is an old German word of uncertain origin used by G. Agricola in 1529.Silica or silica dioxide (Si02) either free or in combination with other elements constitutes 59.08 per cent of the lithosphere, and quartz alone represents fully 12 per cent` of all rocks. Next to the feldspar group quartz is the most abundant mineral in the earth's crust; and it appears in a greater number of varieties and modes of occurrence than any other mineral. Silica or quartz occurs in crystalline, cryptocrystalline, microcrystalline, and amorphous forms. The most common, however, is the crystalline form, which occurs as three minerals, quartz, tridymite, and crystobalite, and of these three tridymite and crystobalite are quite rare in nature."

Aug 1, 1931

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsator-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig.5/ Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this type of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

By H. A. Doerner

From thermodynamic calculations3 Maier predicted that zinc oxide Land methane would react at specified temperatures substantially according to equation (1). (1) ZnO + CH; = Zn (gas) + CO + 2H2 Other reactions that may take place are: (2) CH4 = C + 2H2. (3) ZnO + CO = Zn (gas) + CO2 (4) ZnO + H 2 = Zn (gas) + H2O . Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C.

Jan 1, 1931

By Steven J. Schatzel

Prior research has suggested that the source of respirable silica dust in underground coal mines is typically the immediate top or bottom lithology adjacent to the mined seam, not mineral matter bound within the mined coal bed. Geochemical analyses were applied in an effort to identify the specific source rock of respirable quartz dust in coal mines. The analyses also demonstrate the compositional changes that take place in the generation of the respirable dust fraction from parent rock material. All six mine sites were mining coal with relatively low mineral matter content, although two mines were operating in the Fire Clay coal bed which contains a persistent tonstein. Interpretations of Ca, Mg, Mn, Na, and K concentrations strongly suggest that the top strata above the mined seam is the primary source of mineral dust produced during mining. One site indicates a mixed or bottom source, possibly due to site specific conditions. Respirable dust compositional analyses suggest a direct relationship between the quantity of mineral Si and the quantity of quartz Si. A similar relationship was not found in either the top or bottom rocks adjacent to the mined seam. An apparent loss of elemental Al was noted in the respirable dust fraction when compared to potential parent rock sources. Elemental Al is present in top and bottom rock strata within illite, kaolinite, feldspar, and chlorite. A possible explanation for loss of Al in the respirable dust samples is the removal of clays and possibly chlorite minerals. It is expected that removal of this portion of the Al bearing mineral matter occurs during rock abrasion and dust transport prior to dust capture on the samplers.

Jan 1, 2009

By J. B. Zadra

After the discovery of the rare-earth mineral deposit in the Clark Mountain area near Mountain Pass, San Bernardino County, Calif., two samples wore obtained through the Mining Division of the Bureau of Mines for investigation of possible method of concentration. Three other samples were received later from different locations in the same area. The rare-earth mineral in this ore had been identified by E. T. Schonk as bastnaesite, a fluocarbonate of the rare-earth metals containing cerium, lanthanum, praseodymium, thorium, uranium, etc. Associated with the bastnaesite were barite, silica, and some calcite. The bastnaesite contained a small amount of iron as a coloration and some manganese. Twenty to fifty percent of the weight of the samples studied was bastnaesite, or ten to twenty-five percent total rare-earth oxides; about half was cerium oxide. Apparently, none of this mineral occurred in pure form. Even the highest-grade particles 'wore contaminated by fine, interlocked grains of barite, calcite, and silica; barite contamination predominated, and the barite was interlocked with varying amounts of bastnaesite. While the specific gravities of pure bastnaesite and barite (approximately 5.0 and 4.50 respectively) differ enough to allow separation by gravity, the interlocking of the minerals nullified this difference. Consequently, only a partial separation could be made by gravity concentration. The extremely fine grained texture of most of the ore prevented grinding to a size that would make concentration by flotation practicable; a partial separation of barite by this means was effected.

Jan 1, 1952

By Arne Landsberg

The Bureau of Mines measured the vapor pressure of FeC12 , FeBr2, FeI2, Sb, Bi, Cd, Mg, Pb, FeC13 , and VCl2 using the Knudsen-and torsion-effusion methods, and on FeC13 -NaC1 mixtures, Au2Cl6, and MgNi2 using only the Knudsen method. Apparent vapor pressures calculated from the experimental data vary with orifice size and method of determination. Reaction with residual oxygen in the instruments was noted to have an effect on the iron halide data. Vapor pressure curves plotted as log P versus 1/T (where P is pressure and T is absolute temperature) for one substance using several orifice sizes tended to converge at a single point when extrapolated beyond the experimental region. All of the data, except those of VC12, agree with previously published results. The importance of comparing effusion measurements with those obtained by other methods and the variations encountered with various orifice sizes are discussed.

Jan 1, 1977

By Paul E. Bennett, James S. Browning, Thomas L. McVay

Continuous 1.0- to 1.5 - ton - per - hour pilot plant flotation tests were made to determine the technical and economic feasibility of recovering beryl from flotation tailing being produced at the spodumene concentrator of the Foote Mineral Company , Kings Mountain , N.C. Best results were obtained when using an acid circuit and amine - type cationic reagents to float a bulk beryl - feldspar concentrate and then selectively floating the beryl away from the feldspar , using a petroleum sulfonate collector . About 77 percent of the beryllium in the pilot plant feed was recovered in a concentrate containing 6.42 percent BeO . The capital cost of an integrated flotation plant capable of treating 500 dry tons of spodumene mill tailing per day for recovery of beryl and feldspar is estimated at $ 210,000 . Indicated direct operating costs for the plant were $ 1.52 per ton of dry spodumene flotation tailing treated . This approximated the value of beryl recovered , but potential profits of about the same magnitude lie in concurrent recovery of marketable spodumene and feldspar byproducts .

Jan 1, 1964

By Howard P. Hamlin, John W. Sweeney

Shales from 14 locations in Indiana were sampled , tested , and evaluated to determine feasibility of producing lightweight aggregates by rotary - kiln and sintering methods . Sampling procedures and the geology of the significant shale units are discussed . Preliminary testing was conducted in a muffle furnace , and continuous tests were made in a 16 - inch by 14 - foot rotary kiln . The aggregate weighed 37.0 to 47.2 pounds per cubic foot . Concrete cubes employing the aggregate were tested to determine the qualities of the concrete . Compressive strength of the concrete using seven bags of cement per cubic yard , after autoclave curing for 6 hours , ranged from 3,600 to 5,850 pounds per square inch . Four samples made suitable lightweight aggregate in the laboratory rotary kiln . Four samples tested by sintering methods made unsatisfactory aggregate .

Jan 1, 1965

By Jin Dai, Xianwen Geng, Hao Liu, Pu Wang

To investigate how deformation failure occurs in roadways surrounding rock, the relationship between cohesion and plastic shear strain of the strain softening model and the equation for calculating the shear strain of a rock mass in the ultimate elastic state are derived. On this basis, the equality relationship between the built-in maximum shear strain increment and cohesion of FLAC 3D was established to give a more intuitive picture of how the cohesion of the roadway surrounding rock changes. The cohesion attenuation and deformation of the surrounding rock are analysed. The results show that significant deformation in the roadway surrounding rock was caused primarily by the development of large areas of highly softened plastic rock masses towards residual strength. Taking the floor overhead-mining roadway under different rock pillar thicknesses (RPTs) in the Xinglongzhuang Coal Mine as an example, the results demonstrate that investigating the cohesion distribution inside the roadway during mining operation can provide a more intuitive, more accurate description of the degree of failure of the surrounding rock at any point of the roadway, as well as the overall failure range of the surrounding rock. The simulation agrees well with the field monitoring result and seems to be more practically useful than simply analysing the coverage of shear plastic zones. Based on the failure range and degree of roadway surrounding rock with different RPTs, three support schemes are designed. Classified support was implemented for roadways under different RPTs, which realizes the effective control of roadway surrounding rock.

Jan 16, 2022

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Danu Putra, Budi Sulistianto, Tri Karian, Mohammad Nur Heriawan

Stope layout optimization is an important feature of underground mining that maximizes the economic value of the project while taking mining limits into account. The large number of parameters and constraints makes it difficult to obtain the optimum condition. Several algorithms have been created to address these problems using a variety of methods. However, the circulating method has not explicitly included stope dimension stability analysis, resulting in a solution that is not stability-proven, which can result in a suboptimal solution. This study integrates the Mathews stability graph into the stope optimization algorithm so that the optimized stope layout considers stability conditions directly through an assessment of the available geomechanical data within the block model. The proposed algorithm is validated through a case study of a synthetic block model created by considering variations in grade and the geomechanical conditions of the rock. Furthermore, several scenarios are created to compare the performance of the algorithm that applies variations in stope sizes with the common case study of stope sizes that remain fixed. A more detailed assessment is also conducted on each final stope layout wall to ensure the successful application of stability analysis in the proposed algorithm through back analysis on the Mathews stability graph. The optimization results show that all walls in the final stope layout fall into the stable condition. Also, the proposed algorithm is also capable of maintaining the project’s economic value. Ultimately, the proposed algorithm can be deemed applicable and suitable for use in the initial stages of mining as a comprehensive assessment of the optimal stope layout, taking into account the stability conditions of the stope.

May 22, 2024

By Gregory J. Chekan

The U.S. Bureau of Mines is investigating longwall panel and gate road layouts to increase coal recovery and reduce multiple-seam interactive problems. This report presents design practices for longwall mining multiple seams to provide mine planners and operators with practical guidelines for designing productive longwall mines. Key aspects of mine design that control longwall interactions are examined, including sequencing of seams, design of gate road pillars, and orientation of gate roads and longwall panels. Theories that describe stress transfer between multiple scams and the mechanics of interaction are addressed in relation to geology. Common longwall designs were further investigated using a boundary element model, MULSIM/NL. The model provided insight into relative stress transfer and distribution that occurs between longwall operations in multiple seams. Findings from the model show that (1) a longwall panel should be mined from the gob to the solid coal of an overlying mine, because the stress concentrations are lower; the approach angle should be kept under 30°; and (2) when mining in descending order, superpositioning gate roads usually produces the worst stress condition. To prevent this, the overlying isolated gate roads should be positioned from the centerline toward the headgate side of the underlying panel.

Jan 1, 1993

By William A. Beck

"INTRODUCTION Mica is found in Georgia from the Fall Line in the central part of the State to the Valley and Ridge Province in the northwest. During the past 3 years, Georgia has been one of the chief producers of dielectric mica in the United States. Since January 1945, when prices were reduced, mining has decreased until practically no sheet mica is being recovered at present.The main mica-bearing regions in the State may be classified into three districts: The Thomaston district comprising Upson, Lamar, and Monroe Counties; the Ball Ground district, comprising Cherokee and Pickens Counties; and the Hartwell district, comprising Hart and Elbert Counties. There are numerous mines and prospects in all of these districts. All have been visited from time to time by engineers of the Bureau of Mines and by members of the Federal Geological Survey. The Federal Survey has made detailed maps and reports on all of the most important ones.This report will deal with five of these properties on which the Bureau of Mines has diamond-drilled.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, I. B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and makes beneficiation tests."

Apr 1, 1948

By L. E. Djingheuzian

Introduction For many years the immense deposits of bituminous sands of northern Alberta have been attracting the attention of our governments, engineers and .scientists ( 6). Undoubtedly these bituminous sands represent one of the greatest potential resources of liquid fuels in the world. However, their commercial development has been retarded by the complexities of the technological problem and by the economic factors involved in the processing of the sands. The technological problem has been attacked from several angles ( 2, 3, 1, 11), and cold water separation of bitumen is one of them. To the ore dressing engineer, the cold water process is of utmost importance since, by the use of standard ore dressing machinery, it accomplishes most efficiently and economically the separation of bitumen from bituminous sands. The significance of using ore dressing equipment was especially enhanced by the fact that the scientific principles which underlie the design of standard machines were demonstrated in the cold water separation process with an extraordinary clarity. This greatly facilitated the analysing of limitations and advantages of different machines during-the pilot plant investigations and helped to complete the investigations practically in the allotted time.

Jan 1, 1952