Search Documents

By Robert M. Cox

The objective of this study was to determine if significant relationships exist between coal mine roof stability and the time roof is left unsupported. Additional factors such as geology, opening geometry, and mining methods were also studied: to determine their relative influence on mine roof stability. The results of the study indicate that geologic factors such as shear zones (either joints or faults) and changes in roof rock lithology were the principal factors governing mine roof stability. The time lapse factor appeared to be of critical importance when poor mine roof conditions are encountered. The study pointed up the need for improved and permissible rock mechanics instrumentation for use in coal mine investigations.

Jan 1, 1974

By Nancy Potts, M. G. Barker, W. C. Holliman

"SUMMARYThis report on the characteristics of commercial aviation gasolines presents compilations of inspection test data furnished on their products by manufacturers of commercial grades of aviation gasoline, and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data and physical samples for the survey were submitted by 15 manufacturers on 18 grade 80, 21 grade 91/98, 22 grade 100/130, end 10 grade 115/145 aviation fuels.The inspection test data supplied by the participating manufacturers consist of octane and performance numbers, tetraethyllead content, dye color, and other characteristics usually listed in aviation gasoline specifications, such as AN-F-48a or ASTM Designation D910-47T. These data are tabulated and averaged by grades in tables 1 through 4 and, as reported, meet the AN-F-48a and similar specifications with a few exceptions. Two grade 80 gasolines show a lean-mixture octane rating slightly below 80.0, and 91/98 grade fuel shows a lean-mixture rating of 90.9 and a rich-mixture rating of 97.5, two 100/130 grade gasolines have a rich-mixture performance number slightly below 130.0, and one 115/145 grade gasoline shows a rich-mixture performance number of 144.5. However, octane and performance number averages are above the mini¬mum requirements for each grade. Tetraethyllead content in the 91/98 and 100/ 130 grades generally is above the maximum outlined in these specifications, whereas dye color for each of the four grades, with the exception of two gasolines in grades 80 and 100/130, is that designated for the particular grade. Distillation requirements, with a few exceptions at individual points, are met by gasolines of all grades. Reid-vapor-pressure, copper-dish-residue, heat-of-combustion or aniline-gravity-constant, freezing-point, and copper-strip-corrosion requirements are met by all gasolines so far as reported. No data for some of these tests wore submitted on a few of the gasolines. One gasoline, grade 115/145, shows a sulfur content greater than the specified maximum."

May 1, 1948

By Franklin B. Woodbury

As part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic needs, the U.S. Department of the Interior's Bureau of Mines is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed with a prototype monitoring system. A Californium-252 neutron source and a thermal neutron capture- gamma ray spectra analysis method was utilized to measure the amount of iron and the percent solids in the process slurries. The concentrate and tailing streams in a 410-kilogram-per-hour (900- pound-per-hour) pilot plant employing a selective flocculation and cationic flotation process were monitored. The results obtained showed that the thermal neutron capture-gamma ray reaction can be used to provide process control parameters.

Jan 1, 1979

By Carl Belser

This paper, covering Chaffee, Fremont, Gunnison, Lake, Larimer, Park, and Summit Counties, Colo., is the second of a series reporting on the tungsten potential of the Colorado region. The assembled information was obtained by examination of some properties, personal contacts with owners, and access to unpublished reports by other engineers. The tungsten-bearing areas of the 7 counties cover approximately 400 square miles and are in 10 distinct areas, which vary in size (fig. 1) from 1 square mile up to 290 square miles. The tungsten mineral wolframite was discovered by a man named Hackay near Dale on the Florence & Cripple Creek Railroad in the early 1900's, and wolframite and hubnerite were noted at Climax and the adjacent areas in Lake and Summit Counties at an early date, but no records of shipment from any of the areas are available before World War II. It is not known when scheelite was first discovered, but it was recognized in the Stockton mine during World War I. In the counties listed 64 properties are known to contain tungsten; of these, 18 have had some commercial output, although only 3 of them produced in 1953. The total production through 1953 is estimated at 115,000 short-ton units of tungsten trioxide. In 1953 by far the major portion came from the Climax mine.

Jan 1, 1956

By W. L. Zeigler

This paper describing the milling practice of the Hecla Mining Co. is one of a series being prepared by the United States Bureau of Mines. The concentrator of the Hecla Mining Co., which utilizes combined gravity and flotation methods, is located at Gem, Shoshone County, Idaho, about 2 miles south of the Hecla mine at Burke. It has a maximum capacity of 900 tons per day and all ore treated is drawn from the company's Hecla mine. Milling ore for 1910 contained 9.7 per cent of lead, 1.2 per cent of zinc, and 4.77 ounces of silver per ton.

Jan 1, 1932

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers In their Resource Development Navigation Study, the U.S. Bureau of Mines (Bureau) examined the potential for mineral development near ten Alaska port sites. This report presents the results for the first three sites: Bethel, Kivalina (Red Dog), and Omalik Lagoon. The mineral deposits near Bethel are primarily gold and mercury; the nearest deposit being 55 mites away. Because of the expense of constructing and maintaining a road over the poorly drained lowlands, the potential of Bethel as a port site in the near-term is considered to be low. The Kivalina site currently serves the Red Dog mine and has the potential to handle material for similar deposits in the area. Results from a lead-zinc mine model indicate that potential for additional mine development exists in the area. Coal is the major deposit type found near the Omalik Lagoon site. Due to environmental constraints, development of a large-scale mine producing coal for export is considered unlikely. A small-scale coal mine model was used to examine the feasibility of producing coal for regional use. This alternative may be feasible but would require conversion of heating/generating equipment in the area.

Jan 1, 2011

By W. A. Calhoun

This investigation of low-grade bauxites as potential sources of aluminum by caustic desilication and alumina extraction was undertaken by the Bureau of Mines to develop extractive methods for winning alumina from domestic deposits of low-grade bauxites. This report is the second of a series covering the work by the Bureau of Mines' Rolla, Mo., and Bauxite, Ark., laboratories. The first report published in the Journal of Metals, December 1951,3/ and dealt with kaolin and halloysite. The present investigation is concerned with low-grade bauxites only. The purpose of these investigations is to increase the domestic supply of aluminum ores. With eventual depletion of high-grade deposits, aluminous materials, such as low-grade bauxite, clays, shales, and high-iron laterites, will become our principal domestic sources of aluminum. The development of extractive processes for winning alumina from these low-grade materials is one of the many national security measures undertaken by the Bureau of Mines. A method has-been developed in the laboratory for successfully treating high-silica bauxites from domestic deposits. In this process the bauxite was calcined at 980° C. to form amorphous silica and alumina. The calcine was then leached by percolation with 15-percent sodium hydroxide solution at 940 to 96° C., removing 67 to 77 percent of the silica with a loss of 4.1 to 5.0 percent of the alumina. The sodium hydroxide in the spent liquor used in desilication was 95 percent recoverable, and comparable desilication results were obtained with 100-percent reclaimed liquor, The indicated cost of reagents, for sodium hydroxide and lime used in the desilication and regenera¬tion of spent liquor, was about $4.00 per ton of calcine treated.

Jan 1, 1954

By V. F. Parry

[Approximatel~r 7-1/2 illion tOlls of subb1tnminous coals are mined an-nuall in Colorado, Wyo~ing, and Montana, of which 50 percent probably reaches dome ,-tic conswno:os. r:L'he moi s t'_re of the se subbi t1.Uninous coal sis high, averae;:t.:ug about 25 :!,)ercent \-Then they are :nined. T'ne coals are non-caking d ~~ack to a vari ble degree when exposed to nornal atmospheric conditions. ~hey a~e gpod domestic fuels, are considered to be smokeless in most furn~ces, and have been used. f, r f!1an: y ars in hand-fired domestic furnaces in hich tnc practice i~ to e~ploy large lureps for efficient com-]

Jan 1, 1941

By J. P. Hansen

Reducibility tests were run by the Bureau of Mines on an open hearth lump ore and four groups of pellets whose smelting characteristics had been deter-mined previously in the Bureau's experimental blast furnace. When reduction data from various tests were plotted on specially prepared paper l-(l-percent reduction/100)1/3 against time, the plots were linear. The iron-wustite inter-face therefore advances at a constant rate. The rate of the interface advance in mm/min was used as a reducibility index. The reducibility index measured at 900° C, using 0.45 cu ft hydrogen per minute varied inversely with the surface area of the sample. Even with carefully controlled surface areas, how-ever, duplicate reducibility indices varied considerably. When enough tests were run to give a stable mean, the mean reducibility index did correlate with blast furnace production for the four pellet groups. Results indicated that if the interface speed itself were to be used for correlation with blast furnace production, a sample size of about 180 grams of minus 0.742-plus 0.525-inch particles should be used with a test temperature of 900° C and a flow of 0.45 cu ft hydrogen per minute.

Jan 1, 1966

By C. L. Severy

The Reeder No. 1 well was drilled by the Bureau of Mines in cooperation with the Geological Survey as agents for the Defense Plant Corporation. The well is south of Crescent Junction near Thompson, Grand County, Utah. It was started May 5, 1942, and completed August 3, 1942, for the purpose of con-firming the presence of magnesium salts in a deeply buried bed. Drilling was done under contract by the Mack Drilling Co. This report contains an outline of the physical features of the well, a brief history of drilling, and a description of the deposits and occurrences of oil and gas encountered in the drill hole. The work performed by the Bureau of Mines is described in considerable detail, with particular emphasis on drilling procedure and sampling. The report is concluded with a brief description of core-sample preparation for analyses. Appendix A comprises a log of the drill hole, and appendix B is a tabulation of analyses of cores.

Jan 1, 1949

By G. Roy, D. R. Lentz, A. O. Wills

"Abstract - Diamond-drill hole DDH-B357, located 1.5 km north of the Brunswick No. 6 Zn-Pb- Cu-Ag volcanic-sediment-hosted massive sulfide (VSHMS) deposit, intersects three exhalative horizons within variably altered felsic volcanic rocks of the Nepisiguit Falls and Flat Landing Brook formations. These three petrographically indistinguishable iron formation intervals (Fe2O3T = 21.4 wt.%) likely represent cogenetic hydrothermal sedimentary units because they display a common geochemical signature: Fe2O3T = 42.9 ± 10.5 wt.%, MnO = 5.4 ± 3.1 wt.%, elevated base metal values (Zn+Pb = 1999 ± 1091 ppm), strong enrichment in additional exhalative components (CaO = 5.3 ± 3.9 wt.%; P2O5 = 1.43 ± 1.00 wt.%), oxidized signature (Fe/Mn = 10 ± 6), as well as a common immobile element signature (Zr/TiO2 = 0.025 ± 0.007) representative of a pelagic source. The calc-alkaline to transitional host volcanic rocks can be discriminated by Zr/TiO2, and to a lesser extent by Th/Nb: Nepisiguit Falls Formation: Zr/TiO2 = 0.053 ± 0.004, Th/Nb = 1.08 ± 0.37; Flat Landing Brook Formation: Zr/TiO2 = 0.107 ± 0.043, Th/Nb = 0.86 ± 0.17. A symmetrical repetition of the footwall-iron formation-hanging wall stratigraphic sequence is observed in DDH-B357, with distinct felsic volcanic rock domains separated by the three iron formations. This is best explained by parasitic F2 folds on the west flank of the south-plunging Brunswick antiform, similar to the fold closures known to host massive sulfide accumulations in the Brunswick No. 6 and No. 12 mines. Iron formation geochemistry and felsic volcanic rock chemostratigraphy from drill core sampling can provide an effective mineral exploration tool for the structurally complex rocks of the Bathurst Mining Camp. Sommaire - Le forage au diamant DDH-B357, situé à 1.5 km au nord du gisement de Sulfures Massifs à Encaissant Volcanique et Sédimentaire (SMEVS) de Zn-Pb-Cu-Ag Brunswick No. 6 recoupe trois horizons exhalatifs au sein des roches volcaniques felsiques diversement altérées des formations de Nepisiguit Falls et de Flat Landing Brook. Ces trois intervalles de formation de fer, impossibles à distinguer pétrographiquement les uns des autres, représentent vraisemblablement des unités sédimentaires hydrothermales cogénétiques sur la base de leur signature géochimique commune: Fe2O3T = 42.9 ± 10.5 % poids, MnO = 5.4 ± 3.1 % poids, des teneurs élevées en métaux usuels (Zn+Pb = 1999 ± 1091 ppm), un fort enrichissement en composantes exhalatives additionnelles (CaO = 5.3 ± 3.9 % poids; P2O5 = 1.43 ± 1.00 % poids), une signature oxydée (Fe/ Mn = 10 ± 6), ainsi qu’une signature d’éléments immobiles communs (Zr/TiO2 = 0.025 ± 0.007) indicative d’une source pélagique. Les roches volcaniques encaissantes calco-alcalines à transitionnelles peuvent êtres reconnues par leur rapport Zr/TiO2, et à un moindre degré par leur rapport Th/Nb: Formation de Nepisiguit Falls: Zr/TiO2 = 0.053 ± 0.004, Th/Nb = 1.08 ± 0.37; Formation de Flat Landing Brook: Zr/TiO2 = 0.107 ± 0.043, Th/Nb = 0.86 ± 0.17. Une répétition symétrique de la séquence stratigraphique Mur-Formation de Fer-Toit a été observée dans le forage DDH-B357, avec des domaines distincts constitués de roches volcaniques felsiques séparés par les trois formations de fer. La meilleure explication est que le flanc ouest de l’anticlinal Brunswick à plongée sud est affecté par des plis parasites F2, similaires aux zones de charnière contenant les sulfures massifs des mines Brunswick No. 6 et No. 12. La géochimie des formations de fer et la chimiostratigraphie des roches volcaniques felsiques en forage peuvent fournir un outil d’exploration minérale efficace dans les roches structuralement complexes du Camp Minier de Bathurst."

Jan 1, 2006

By Frederick W. Horton

With large deposits of low-grade molybdenum ore and a latent market for molybdenum, which with development might perhaps equal that for tungsten, the United States has for years made no pro- duction of molybdenum ore worthy of mention. In fact, during the decade previous to 1914, there was no output of molybdenum ore in this country except in 1905, 1906, and 1907, when a few small lots of molybdenite and wulfenite were marketed." To ascertain why this possible source of economic wealth should remain undeveloped, the United States Bureau of Mines undertook an investigation in 1914, with a view of assisting the establishment of a molybdenum industry in this country. A preliminary review of the situation showed the following conditions: Briefly there was a lack of any considerable demand for molyb- denum for the one known use that might consume any large tonnage of it, that is, for the manufacture to certain alloy steels to which molybdenum imparts properties roughly similar to those produced by tungsten. It was at once evident that the market for molybdenum in alloy steels must be developed, or that extensive new uses for the metal must be created, before the demand would be sufficient to war- rant any extensive mining of molybdenum ore. Investigation showed that one of the chief factors in retarding the development of any demand for molybdenum by the alloy-steel trade was that manufacturers who might use, or might investigate the possibilities of using, the metal were kept out of the market by the fear of not being able to obtain steady supplies. On the other hand, those who might be interested in the development of some of the extensive low-grade molybdenite or wulfenite deposits in this country were prevented from doing so by the small visible demand and the fear that any large production would glut the market. Owing to these conditions the mining of molybdenum has in the past been confined almost entirely to small-scale operations on high-grade streaks of molybdenite ore, and the methods of recovery have been limited largely to cobbing and hand picking.

Jan 1, 1916

By R. M. Santmyers

The pigments, whose colors are due primarily to iron exides and iron hydroxides, comprise a variety of yellow, brown, red, and sometimes black paint-coloring agents, both natural and artificially prepared. The natural pigments in this group include ocher, umber, sienna, mineral paints, paint rock, and mortar colors. When the natural color or tinting power--either in the raw state or after treatment--is too weak, these pigments may be "forti- fied" or strengthened. Ocher, umber, and sienna, rhile often described as "iron oxide pigments," are also known as "earthy" rigments. Inasmuch as the iron content of these pigments is, in general, somewhat lower than that of other iron oxide pigments, the ochers, umbers, siennes, and other brown earth pigments are not discussed in the present paper. In addition to a discussion of natural or artificial pigments whose color is due to the presence of iron oxide in some form, this paper contains data on mortar colors, which are medium or low grade pigments used for tinting mortar, cement, and concrete. A great variety of materials are used for theso purposes, including "blue billy" (residue left from roast- ing pyrite), ground slate and shale, and even culm from coal washeries. Dur- ing the past three years, there has been a definite trend among the producers of iron oxide pigments to push the sales of the better grades of colors for tinting mortars. Due to the amount of low-grade coloring matter that is re- quired to impart a strong color to concrete (in soro cases as high as 15 per cent of pigment is necessary) the strength of the cement may be materially impaired. The addition of some 2 per cent of the higher grades of iron oxide to the concrete mix imparts a brighter and stronger colcr, does not weaken the material, and in the end is not as expensive as the low-grade pigments formerly used. Iron oxide pigments occur in nature in various shades and colors, but the red pigments are the most important and account for the larger part of the total red pigments used.3/ The nomenclature of these red pigments is involved and the names given to them are descriptive of the shade rather than of origin, method of produc- tion or chemical composition. In most cases the red pigments under this class may occur naturally or may be produced by heating hydrous iron oxide pigments such as yellow ocher to a sufficiently high temperature to drive off the water of composition. They may also be prepared by fortifying naturally-occurring pigments with stronger natural or synthetic oxides or with coal-tar dyes (e.g. alizarine lake), Most of the mineral reds derive their color from the presence of ferric oxide (Fe2O3), the mineral hematite. This may be present in relatively small percentages, as in the red slates and shales, or it may constitute as much as 90 per cent or more of the material, as in Spanish red. The principal iron oxide pigments used in the manufacture of paint are discussed in the following pages.

May 1, 1932

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By George S. Rice, F. B. LANEY, A. J. Lanza, Edwin Higgins

Under its organic act the Federal Bureau of Mines is directed to conduct investigations relating to the improvement of health conditions in the mineral industries. This report describes the lead and zino deposits and the mining methods employed in the sheet-ground area of the Joplin district, Missouri, and discusses the causes and the methods of abating rock dust in the mines, the chemical and physical characteristics of the dust, and the quantities present in mine air. Although the preliminary investigation included a number of the "soft-ground" mines, the writer spent the larger part of his time in the sheet-ground mines, for in them alone was siliceous dust found in appreciable quantities. Some results of the preliminary investigation have been published by the Bureau of Mines in Technical Paper 105.a The territory covered in t~lCpreliminary investigation, during the period between November 7 and December 6, 1914, embraced parts of Jasper, Lawrence, Newton, and Greene Counties, Mo., and outlying districts in Kansas and Oklahoma. The remainder of the field work, to which 84 days during the period from February 9 to July 19, 1915, were devoted, was confined to the sheet-ground mines, the most important of which are situated in the vicinity of Joplin, Webb City, Carterville, and other smaller near-by towns in Jasper County, Mo.

Jan 1, 1917

By Cleo G. Rall

The value of brine analyses in the study of petroleum-engineering problems was recognized early in the history of petroleum. The Bureau of Mines before 1928 had indicated in several reports.3/ ways in which analyses might be used. Because of the confusion resulting from attempts to correlate the work of different chemists using greatly varying methods of analysis and systems of computation and expression of results, a paper presenting the methods used by the Bureau of Mines was prepared and published in 1928. This system of determining the characteristic constituents of oil-field waters and of calculating and reporting results has been widely adopted by the petroleum industry. The earliest and most obvious use of water analyses is determination of the source of water infiltrating into petroleum and natural-gas wells. For this purpose it is necessary that an analysis of the connate water of the formation from which the oil is produced be available and that an analysis of the contaminated water be made. By comparing these analyses with those of connate waters from formations higher in the structure, the formation from which the infiltrating water comes may be identified.

Jan 1, 1953

"INTRODUCTION While investigating prevention of sabotage and maintenance of production of essential war minerals, engineers of the Bureau of Mines visited more than 1,400 metal and nonmetallic mines, quarries, and open pits in all parts of the United States.The need for, uniform safety practices is indicated by the fact that during 1938-1940, inclusive, the Western Safety Conference, under the sponsorship of the California Department of Industrial Relations, undertook the prepara¬tion of a set of standard safety regulations for the 15 participating political subdivisions. The membership of these political subdivisions is comprised of representation from Alaska, Arizona, British Columbia, California, Colorado, Hawaii, Idaho, Lower California, Montana, Nevada, New Mexico, Oregon, Utah, Washington, and Wyoming, For the guidance of its own engineers; the Bureau of Nines found it necessary to prepare a set of safety practices that could be used uniformly throughout the United States. These safety practices were compiled from State mining regulations, mining company safety rules, and the experience of Bureau of Mines engineers for more than 3 decades, and represent the best safety practices of the Nation's' mineral industry.The purpose of this publication is to make safety practices available for the non-coal branches of the mineral industry, with the hope that they may assist in reducing accident occurrence. The Bureau will welcome questions and suggestions regarding these practices in order that changes may be made as necessary.Where the adoption of any practice would not materially increase the safety of employees or would work undue hardship on the operator, the Bureau does not recommend such adoption."

Sep 1, 1946

By Carl L. Bieniewski

U.S. molybdenum production increased fivefold from 18.2 million pounds in 1946 to 90.5 million pounds in 1966, and constituted 87.3 percent of the total free world supply in the 1946-66 period. Mining development in other free world countries in the next few years may reduce the magnitude of the U.S. position, although similar development planned for the United States may counteract some of the relative gains by those countries. In 1966 two-thirds of the reported molybdenum consumption in the United States by end uses was as an alloying element in steel. Molybdenum also has important use as an alloying element in iron and high-temperature alloys. Consumption of molybdenum metal for making fabricated parts has increased in the past few years, especially in the space and nuclear industries. Molybdenum compounds are used mainly for making pigment, catalysts, and lubricants. Based on producer reports of shipments of primary products to domestic customers, U.S. consumption of molybdenum increased from 16.5 million pounds of molybdenum in 1946 to 65.6 million pounds in 1966. U.S. molybdenum reserves are now estimated to be 5.9 billion pounds of recoverable molybdenum, an increase of 2.1 billion pounds above previous estimates. Molybdenum ores account for 71.4 percent of the reserves, copper ores for 22.3 percent and copper-molybdenum, tungsten, and uranium ores for 6.3 percent. Several methods for predicting future demand are illustrated and estimates of demand using these methods were made for 1975. Based on present capacities and announced company plans for future developments, estimates of annual production were made for 1967 through 1975 for the United States, Canada. Chile, Peru, and the free world. These data indicate that molybdenum production in 1975 for the free world is expected to be 246 million pounds with the United States producing 68.2 percent and Canada, Chile, and Peru 30.3 percent.

Jan 1, 1970

By Gerhard Braüner

The present knowledge on ground movements and mining damage is mainly based on observations made when mining seamlike deposits. The studies, rules, and regulations in different countries agree in that the differential ground movements, especially the strain, account for the damage to structures. Accordingly, large buildings are particularly susceptible. The opinions on what amount of ground deformation induces what degree of structural damage are not quite uniform. Mining damage can be reduced or prevented by structural and/or underground precautions. The latter comprise measures for generally reducing the ground movements (leaving pillars, filling, partial extraction) and for reducing temporary movements (rapid extraction, specially arranged workings). Because the differential movements decrease with increasing depth of mining, safety pillars are largely dispensable at greater depths. Shafts are mainly affected by the vertical derivatives of rock displacements, but extraction in the vicinity of shafts is feasible even under difficult conditions. The theoretical concept of the ground movement process established in part 1 of this work is in qualitative agreement with the facts herein observed. As a quantitative approach, it should be applied to calculating ground surface movements rather than rock movements about underground openings. It can be extended by introducing more detailed strata characteristics.

Jan 1, 1973

By William W. Aljoe

The hydrologic characteristics of two abandoned underground coal mine sites, near Latrobe, PA, and Uniontown, PA, were investigated by the U.S. Bureau of Mines for possible implementation of alkaline injection into the mine pools as a means of abating their acid discharges. The Latrobe site was chosen for a one-time application of alkaline injection to achieve a partial, short-term neutralization of a limited portion of the mine pool. A quantity of alkaline reagent (sodium hydroxide) sufficient for a one-time neutralization of the water in this portion of the pool was added. Although nearly all of the neutralizing reagent had moved away from the injection wells within 6 weeks, no evidence of neutralization was noted at the mine discharge during the study period. This lack of neutralization probably occurred because the injection wells did not intercept a primary flow path through the mine. Criteria for successful application of alkaline injection at this or other sites include (1) positive identification of the primary flow paths through the mine pool and (2) addition of quantities of alkaline reagent sufficient to neutralize the entire volume of the pool along the primary flow path.

Jan 1, 2010