Search Documents

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Harrison County, W. Va. It is one in a series of Federal Bureau of Mines reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 6.5 million tons of coal was produced in Harrison County, W. Va., in 1958, of which over 3.7 million tons was cleaned mechanically in seven preparation plants. All of the coal cleaned was from the Pittsburgh bed. It has been estimated that more than 1,816 million tons of coal remains in the county in beds 12 inches or more thick. The Pittsburgh and Redstone beds were selected by the Bureau for a study based on current production rates and estimated minable reserves. Sample locations were selected following a study of the literature, conferences with mining engineers and mining company officials in the field, and examination of the available sites. Six samples were collected from the Pittsburgh bed, and three samples came from the Redstone bed, Float-and-sink tests of the samples collected from the Pittsburgh and Redstone beds showed that neither coal could be upgraded to a metallurgical fuel under the standards set up for this study, even after intensive preparation. Finer crushing of the samples moderately increased the yields and slightly reduced both the ash and the sulfur contents in the 1.30-specific-gravity float fractions. Finer crushing slightly decreased the yields in the 1.58-specific-gravity float fractions, whereas it reduced the sulfur content 0.11 percent for the Redstone sample and 0.46 for the Pittsburgh sample.

Jan 1, 1961

This publication contains four papers presented at a seminar on mine subsidence control held in Pittsburgh, PA, on September 19, 1985. The seminar was designed to keep the mineral industry informed of new technology developed by the Bureau of Mines that permits reliable and accurate prediction of mine subsidence. The papers describe actual field studies undertaken by the Bureau to monitor surface subsidence over longwall panels. Topics discussed include the efects of subsidence on water table levels, the development of subsidence pre calculation methodology suitable for use with the specific lithological conditions of the Pittsburgh coalbed, an engineering comparison of technologies used in surveying for longwall mine subsidence, and a comparison of the process of subsidence over two different longwall panels.

Jan 1, 1985

By Albert L. Toenges

The State Division of Geology Arkansas Resources and Development Commission, and the Arkansas-Oklahoma Coal, Operators Association requested assistance from the Bureau of Mines in a study of coal-mining methods and practices in .Arkansas coal mines with the objective of reducing production costs. On October 7, 1946, a joint meeting was held by representatives of the Arkansas Resources and Development Commission, approximately 30 coal-mine Operators of the Arkansas -Oklahoma Coal Operaters Association, and representatives of the Bureau of Mines. The many problems confronting the coal industry in Arkansas, including mechanical mining in thin beds, costs, labor, and working time were discussed. Following this Meeting, a joint letter from Harold B. Foxhall, State geologist, and -P. R. Stewart, commissioner, Arkansas-Oklahoma Coal Operators Association, was addressed to Dr. R. R. Sayers; former ,Director of the Bureau of Mines, requesting that mining conditions in Arkansas be studied.

Jan 1, 1949

By G. M. Molinda

The U.S. Bureau of Mines conducted an investigation to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure and suggestions for controlling this problem are presented. Hazardous roof conditions identified in some mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52 pct of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath several valleys in the form of bedding plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomena, was found at mining depths as great as 300 ft. In situ, horizontal stress measurements beneath a valley and the adjacent hillsides, confirmed valley stress relief. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress.

Jan 1, 2010

By F. W. Wood

ORIGINAL experimentation in specially designed arc-melting furnaces and a comprehensive review of technical literature have helped with an understanding of electric arcs as used in metallurgical applications. Results relevant to the distribution of electric potentials and currents, temperatures, pressures, the consumption of electrodes, the identities of particles participating in electrical conduction, and the modes and mechanisms of discharge are presented and discussed. Present knowledge of high-current arcs is insufficient to test pertinent theoretical suggestions. However, the chief doubts concern the identities and the liberation or formation of current-carrying particles. It seems that either (1) novel formulations of existing concepts are needed, or (2) essentially new concepts must be recognized to explain observations. An analysis of the situation has led the authors to favor the latter possibility and to suggest the existence of supplementary conducting particles. The conduction of current by the streaming of charged agglomerates is postulated. Another outgrowth of analysis is an equation for the arc potential as a function of current densities in the arc. In lieu of conclusions, the potentialities of practical applications and specific needs for fundamental clarification are summarized.

Jan 1, 1965

By Arnold P. Pipilen

In a study of the principal factors affecting the transport of coal-water mixtures through a centrifugal pump and a pipeline, the interrelation between solids concentration, velocity, and pressure drop was established for a bituminous lump coal (minus 2 inch) in concentrations up to 48 weight-percent. An optimum concentration was found to exist for maximum capacity of a given pipe-line, and for minimum energy requirements per ton of coal. Coal size degradation by particle fracture took place in the pump; abrasion and attrition to form fines took place in both pump and line. A novel system of studying flow of solid-liquid mixtures in pipelines by the determination of relative sound intensities was developed.

Jan 1, 1966

By V. E. Dawson

Brake testing of large mining trucks was initiated in British. Columbia in 1969 following an accident involving the failure of the service brakes of a l00-ton electric-drive truck. Some selected results of the 1976 brake test program are presented and discussed ?in this paper . The tests were conducted on end- dump trucks having load capacities ranging from 85 to 235 tons. All tests were made with the vehicles fully loaded operating on downhill grades varying from 8 to 10 %. Stopping distances were measured from initial speeds varying between 10 and 39 mph. The results are adequate, in most cases, to determine the "ultimate" capabilities of the service brakes of varying models and sizes of haulage trucks operating in British Columbia mines.

Jan 1, 1977

By J. F. McIlwain

Cobalt-base hardfacing alloys used for wear resistance consist almost entirely of metals largely imported into the United States. As part of an overall research program to help alleviate this foreign dependency, the Bureau of Mines has been investigating an iron-base alloy system as a potential replacement for cobalt-base alloys for some uses. To ascertain the melting ranges, thermal analyses were made of cast heats of alloys containing, in weight percent, 59-61 Fe, 16-19 Cr, 8-9 Ni, 1 Mn, 1 W, 1 Mo, 0.5 Cb, 0.6 Si, 0.3 C, and 0-12 stoichiometric TiB2. Powder alloys within this range of composition, prepared by mechanical alloying, were sized and applied to mild steel test coupons by nontrans-ferred-arc plasma spraying. The resulting thin coatings were >95 pet dense, with bond strengths of 35 MPa and hardness of 400 to 840 DPH. Abrasive and adhesive wear test data were compared to those of a plasma-sprayed cobalt-base alloy. A range of boride contents resulting in most promising properties was determined for further research.

Jan 1, 1985

By F. F. Peng

For a given flotation system, the rate-controlling step in fine coal flotation can be the attachment of bubble to the fine coal particles. The probability of attachment depends upon the surface characteristics and the collector adsorption on the coal particle surfaces. Thus, to further improve the flotation rate and selectivity is to alter the distribution of hydrophobicity on coal particles efficiently by applying the effective means of collector dispersion. In order to enhance the combustible recovery and selectivity of fine coal flotation, and lower the amount of collector used in the fine coal flotation processes, four modes collector dispersion/addition techniques are tested. They are direct liquid addition in pulp (mechanical agitation), ultrasonic energy dispersed collector into pulp, atomized collector into pulp and gasified collector transported by air and formation of collector-air bubbles in pulp. The effect of four collector dispersion/addition methods on the floatability of -600 µ m (-30 mesh US sieve) coal samples from four ranks of coals were studied. The ultrasonic energy dispersed collector and atomized collector flotation processes enhance flotation yield and most significantly improve the kinetics of fine coal flotation. The gasified flotation process can increase the selectivity of separation and decrease the collector consumption due to starvation flotation is achieved in this process. The flotation efficiency of gasified collector process is as high as that of conventional flotation. It is because that the effect of the decrease in the combustible recovery is offset by the increase of selectivity. In addition to flotation experiments, induction times of bubble attachment to the bed of fine coal particles for four ranks of coals are measured.

Jan 1, 1992

By Ruddle R. W.

Solid mattes are generally held to be either (a) eutectiferous mixtures of the component sulphides Cu2S and FeS or (b) mixtures of complex sulphides. This chapter shows that liquid mattes consist essentially of a homogeneous phase in which iron, copper and sulphur are present. The amount of sulphur is generally less than that required to account for all the metals as stoichiometric sulphides; mattes cannot therefore be regarded as mixtures of FeS and Cu2S. Some iron oxide may be dissolved in the sulphide phase and magnetite is often present as a second phase. If the sulphur content of the matte is reduced the composition enters the miscibility gap in the ternary system and either an iron- or copper-rich solution (depending upon the composition of the matte) separates as a new phase. On solidification any one of four phases (iron, copper, Cu2S and FeS solid solutions) may crystallize as primaries. The remainder of the matte solidifies as a ternary eutectic. It is possible that iron oxides enter into this eutectic. Knowledge of the ternary Cu-Fe-S system is far from complete and nothing is known of the quaternary system Cu-Fe-S-O

Jan 1, 1953

By J Zhou

Gold in sulfide ores is associated predominantly with sulfide minerals and occurs as both microscopic and submicroscopic particles. In non-refractory sulfide ores, gold occurs mainly as coarse- and medium-grained particles. Minute inclusions and submicroscopic gold usually account for a minor portion. In contrast, gold in refractory sulfide ores occurs mainly as minute particles and submicroscopic gold, and microscopic gold usually accounts for an insignificant portion. In gold ores containing carbonaceous material, the preg-robbing nature of carbonaceous material may impose challenges on gold extraction and cause gold losses. To extract gold from refractory sulfide ores, the ore needs to be finely ground and preoxidation is often required. Sulfide host minerals must first be oxidised to create a porous structure through which the cyanide leach solution can penetrate to reach the colloidal gold particles. The oxidation is traditionally achieved by roasting, autoclaving or bacterial oxidation. In carbonaceous sulfide ores exhibiting a preg-robbing nature, the carbonaceous material needs to be treated by roasting, autoclaving or other means to minimise the preg-robbing effect. As a predictive and troubleshooting tool, the gold deportment study plays an important role in gold metallurgy. It determines the deportment of gold in an ore or mill product and identifies the mineralogical issues that may affect or may have affected gold extraction. The information acquired from a gold deportment study can be used to assist in process selection, flow sheet development, recovery improvement and reagent optimisation.CITATION:Zhou, J, 2013. Deportment of gold in sulfide ores and implications for gold extraction, in Proceedings World Gold 2013 , pp 433-442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics are presented for air in a 2 - inch pipe - type electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig using a negative discharge electrode . Results of this one - geometry study show that current - voltage relationships are a function of air pressure and temperature and indicate that precipitators can be used at any temperature through about 1,350 ° F over the full range of pressure . Corona starting voltage and sparkover voltage vary directly with pressure and inversely with temperature . At temperatures above 1,350 ° F use of precipitators may be limited to operations at pressures somewhat above atmospheric pressure . Theoretical derivations are presented that relate the effect of gas density on corona starting voltage and the effect of ion mobility on corona current . Deviation from the theory is noted at high current levels . Theoretical discussion is presented to explain the apparent electrical limitations for use of precipitators at high temperature , low gas density , and high corona currents , conditions at which calculated ionic velocities are extremely high . Experimental results are interpreted in terms of the theory presented . 1,500 ° F thermal ionization does not appear to be a critical factor .

Jan 1, 1963

By D. Bienstock, R. C. Kurtzrock, E. R. Bauer, J. H. Field

To remove hydrocarbons and carbon monoxide in automotive exhaust by oxidation , a catalyst of 4.2 percent Uз Og , 1.7 percent Cr₂ 0 , and 1.7 percent CuO supported on 1 /8 - inch y- alumina spheres was tested in a reactor in place of the muffler of a 1 / 2 - ton truck . Tests were made with both nonleaded and leaded gasolines . With the engine at operating temperature , tests were made with the engine idling and with the vehicle cruising at 30 mph . Auxiliary air was added to maintain an oxygen concentration of 3 to 4 percent in the gas leaving the catalytic reactor . The vehicle was operated for 83 hours (about 60 percent of the time with the engine idling ) and 525 miles with nonleaded gasoline . Conversions of 98 percent of the hydrocarbons and 100 percent of the carbon monoxide were achieved with the engine idling and with 7,000 ppm carbon atoms and 4- percent carbon monoxide in the feed to the reactor . Hydrocarbon conversions of 75 percent were obtained at cruising speeds of 30 mph with a feed of 1,700 ppm carbon atoms ; the carbon monoxide concentration was less than 0.3 percent in the feed and was unchanged in passage through the reactor . Identical activity was obtained initially in switching to a gasoline containing 1.9 ml tetraethyl lead (TEL) per gallon . However, there was a gradual loss in activity thereafter . Conversions in tests with the engine idling about 50 percent of the time , had decreased by 23 percent for the hydrocarbons and by 25 percent for the carbon monoxide from their initial values after 122 hours and 1,300 miles of operation with leaded gasoline . The levels of radioactive materials in the exhaust of the reactor and the radiation in the vehicle were negligible .

Jan 1, 1963

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicated the potential for scrap formation, validated through lab experiments with varying coke rate, basicity, and holding time. The investigation discovered that smelting this combination could yield a metal product comprising 59% Fe, 24.93% Cr, 7.56% Mn, 0.62% Ni, and 0.93% Si. The optimum basicity was found to be 0.6 with 80% recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall CO2 emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of USD 330 per ton.

Jan 10, 2024

By W. G. Pariseau

Joints may be taken into account when using numerical modeling as an aid to mine design by embedding joints in the model. When using the popular finite element method, say UT3PC, a pre-analysis step is necessary, Step 0. This step is for the computation of equivalent properties of a representative elementary volume of jointed rock (REV) in the model. This Step 0 is taken before Steps 1, 2 and 3 for specification of a rock properties file, generation of the mesh, and model analysis are taken. A brief explanation of equivalent properties and several examples aid in explaining the details of Step 0. Focus is on procedures, input files, and output to show ease of computation. Theoretical details are relegated to references (e.g. Pariseau 2022). Comparisons of safety factor distributions about example mine excavations with direct scaling from mine observations then offer some insights concerning equivalent properties, especially strengths.

Feb 1, 2023

By J. K. Hrica, T. J. Orr, J. Navoyski, B. Macdonald, C. L. Hoebbel, J. L. Bellanca, B. Demich

Haul truck fatal accidents and injuries continue to be a significant concern for the mining industry. However, the availability of high-quality training materials continues to be limited. Near-miss incident accounts, if packaged well, could help fill this gap, because for every fatality, there are hundreds of reportable accidents and thousands of undocumented near misses. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected detailed accounts of 21 near-miss incidents in virtual interviews with mineworkers at surface mining operations across the country. From these interviews, researchers created four simulation videos. The videos bring these events to life through first-person retelling and various visual perspectives of actual events. Each video exemplifies a critical safety message and a common haul truck hazard. This paper describes the process of taking narratives and turning them into impactful visual stories. NIOSH plans to co-release these simulation videos with the Mine Safety and Health Administration (MSHA) to the mining industry to raise awareness and ultimately help reduce haul truck-related accidents and fatalities in mining.

Feb 1, 2023

By Spangler Ricker, F. T. Johnson

"SUMMARYThe Ione-Carbondale clays area is 2 miles northwesterly of Ione, Amador County, Calif. It was explored during the war by the Bureau of Mines to obtain data on the alumina content and to recover representative samples for beneficiation tests for alumina recovery.Seventy holes, aggregating 8,837 feet, were drilled, and about 10.3 acres of land was cleared of underbrush. Maps and cross sections were compiled showing location of holes, analyses, and other pertinent data.The clay beds vary in thickness from 13 to 196 feet, and are covered by a loose overburden, averaging about 11.9 feet in thickness. The ratio of overburden to clay is 1 : 8.2. Analysis of a composite sample showed the recoverable alumina (A12O3) and Fe2O3 content to be in the order of 23.6 percent and 2.8 percent, respectively.Topography of the clay area is ideal for open-pit mining methods and plant site.INTRODUCTIONInvestigation of alumina-rich clays for the possible production of aluminum was made during the recent war period, when the shortage of bauxite was becoming critical.Results of field examinations by the Bureau of Mines and the Federal Geological Survey indicated that one of the most promising areas for the development of alumina-rich clays is in the Ione-Carbondale district."

Mar 1, 1948

By Laís Ávila de Oliveira Silva

A aplicação de ligas de NiTi como biomateriais exige que sua superfície tenha um excelente acabamento final, para garantir a alta resistência à corrosão e a biocompatibilidade. O polimento eletrolítico é um processo capaz de diminuir as imperfeições da superfície, sem alterar as propriedades do material, e de formar uma fina camada protetora de TiO2. Nesse estudo, foram realizados eletropolimentos em fios superelásticos e com memória de forma, usando dois eletrólitos ácidos distintos. A partir dos resultados obtidos, foi possível concluir que a solução de ácido sulfúrico produz superfícies mais homogêneas do que o de ácido perclórico, para os mesmos tempos de polimento, e se apresenta como uma boa alternativa para o tratamento superficial de ligas superelásticas e martensíticas de para sua aplicação como biomateriais.

Aug 17, 2017

By Y. L. Tian

Low-grade bauxite with A/S of 4.4 from Henan province was used as raw material and the selec-tive grinding of bauxite, grinding efficiency, particle size and Al2O3 and SiO2distributions of ground products were investigated using ball and vibration mills. The results show that the selective grinding can be used to realize the separation of aluminum from silicon within a certain particle size. The optimal grinding conditions of the ball mill with bauxite are as follows: grinding material to charge ratio, 1.2, charge volume ratio, 40%, pulp con-centration, 70wt%, medium size distribution, F30mm:F20mm:F15mm=20%:50%:30%. Under the conditions, the weight rate of ground product with A/S over 7.5 is 27% and the recovery of Al 2O3is 30%. The optimal grinding condition of the vibration mill with bauxite are as follows: grinding material to charge ratio, 0.9; charge volume ratio, 70%; concentration, 70%; medium size distribution, F40mm:F30mm:F20mm=20%:30%:50%. Under the conditions, the weight ratio of ground product with A/S over 7.5 is 25% and the recovery of Al 2O3is 27%. The research is significant for the rational and economical utilization of the low-grade bauxite.

Jan 1, 2014

By B. W. Gandrud

In 1927 Coghill showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and 'high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe. These ores slime readily during grinding, and in most instances the slimes are only slightly higher grade than the original ore. Not only do they carry a considerable percentage of the total iron in the ore, so that to reject them as tailings would result in prohibitively low extraction, but they are too fine to be amenable to ordinary methods of gravity concentration. In 1929 the Bureau of Mines published results showing that certain Alabama oolitic iron ores could be concentrated by classification and tabling after grinding, with rubber-covered rods. This selective grinding produced slimes of much higher grade than the original ore, and they were considered part of the final concentrate.

Jan 1, 1934