Search Documents

By M. S. Raseroka

An experimental rig has been constructed to produce chloride stress corrosion cracks in Type 304L stainless steel tube samples. The samples are to be used to test possible in situ repair methods in future work. The factor which influences the time to failure most strongly is the sample temperature; the distribution of cracks within the sample is affected by local temperature variations and by the position of the water line. Low-frequency oscillations in stress, caused by the on-off temperature controller, did not appear to influence cracking in these tests.

Jan 1, 2009

By Hibbert W. D, Lottrey A

The behaviour of coal in a process is a function of both the coal properties and the processing conditions. In the case of the Loy Yang coal deposit, extensive testing has been undertaken to determine: ò the extent, distribution and structure of the coal resource; ò the variations in properties throughout the resource; and ò evaluation of the behaviour of the coal during processing. This has involved the conduct of an extensive borehole drilling program, backed by geological modelling and material characterisation (chemical, physico-chemical and petrological). Evaluation of the behaviour of the coal during processing has ranged from theoretical modelling, laboratory-scale investigations through to pilot scale and full-scale tests. Until recently, the bulk of the work was directed at evaluating the behaviour of the coal for existing pulverised fuel (pf) firing/steam boiler technology and a high level of understanding has been developed of both the coal resource and its behaviour within these systems. More recent efforts have been directed towards the evaluation of new technologies directed towards cheaper and more efficient power generation using this coal. Loy Yang coal has been evaluated in the following technologies: ò Hydrothermal dewatering/direct coal-fired gas turbine; ò Steam fluidised bed drying; ò Solar drying/densification; ò Briquetting; and ò Gasification.

Jan 1, 1992

By Steve Kral

A near-record crowd of mining history enthusiasts made the trip to Leadville, CO in September to attend the National Mining Hall of Fame and Museum’s 19th induction banquet. Dressed in Victorian garb, black tie tuxedos and formal gowns, the 268 people honored four distinguished men who made a lasting impact on the U.S. mining industry. They joined 188 other inductees. The first induction banquet took place in 1988, with about 500 people attending.

Jan 1, 2007

A series of electron beam, cold hearth, single melt Ti-6Al-4V plates (nominally 2.5 cm thick) impacted by 2cm diameter, 4340 steel projectiles (with 54g nominal mass) at velocities ranging from 0.633 to 1.027 km/s were sectioned along the impact axis and examined by optical metallography to characterize the formation, growth, and microstructure of adiabatic shear bands. Near ballistic limit velocities, the shear bands propagate towards the rear of the target where they coalesce and grow to provide a cylindrical solid state flow regime for the plug volume.

Jan 1, 2006

By Xing Zhao, Michael A. Sutton, Vikrant Tiwari, Damien Bretall, Xiaomin Deng, William L. Fourney, Uli Leiste

The dynamic response of a thin aluminum plate subjected to both shallow and deeper buried blast loading was studied. Using a combination of high speed stereo-vision and three dimensional digital image correlation (3D-DIC), sequential stereo images acquired every 38.25µs during blast loading were analyzed to determine full-field deformations and plate motions (displacements, velocities and accelerations, effective surface strain and effective surface strain rate). Measurements indicate that the initial sheet deformation was highly localized for both shallow and deeper blast events, with extremely high velocity and acceleration values recorded during the earliest stages of impact loading. Full field strain and strain rate data indicate that well defined strain and strain rate “maxima” are created in the plate, with the potential of affecting the dynamic plate behavior as well as it local failure.

Jan 1, 2010

Kudremukh Iron Ore Company Ltd, a wholly owned Government of India Enterprise, was established in the year 1976 to develop mine and plant facilities to produce 7.5 Mtpa of high-grade iron ore concentrate at Kudremukh. The mine and plant facilities were commissioned in 1980. In view of high demand for iron oxide pellets in iron and steel industry worldwide and as a diversification activity, a pelletisation plant of 3.0 Mtpa capacity was commissioned in the year 1987 at Mangalore for production of high-quality blast furnace and direct reduction grade pellets for export. The pellet plant capacity has been increased to 3.5 Mtpa by technological improvement which included installation of roll press for quality and productivity improvement. In addition, the pellet capacity is being increased to 4 Mtpa by the addition of Shaft Pelletising Furnace plant.

Jan 1, 1999

By C. R. Edwards

"The Cigar Lake project will develop the world’s second largest high grade uranium deposit. The Cigar Lake Phase 1 orebody contains approximately 226 million pounds U3O8 at an average grade of 20.7% U3O8. The mine, to be operated by Cameco Corporation, will use a unique water jet boring mining method to cut previously frozen ore. A distinctive ore handling design is required to handle the high grade ore slurry exiting the mining machines. The ore will be crushed and ground underground, with the ore slurry then pumped to surface. Loaded into purpose-designed containers on tractor-trailer units, the ore slurry will be trucked to Cogema Resources Incorporated’s McClean Lake mill. McClean Lake will leach all of the ore. Forty-three percent of the resulting uranium solution will remain at McClean Lake for processing into yellowcake. The other 57% of the uranium solution will be shipped to Cameco’s Rabbit Lake mill for processing into yellowcake there. Detailed design for the Cigar Lake project is now underway. Barring regulatory or market delays, production could start up as soon as early 2005.INTRODUCTIONThe Athabasca Basin in northern Saskatchewan hosts a number of large uranium mining and milling operations, including Cluff Lake, Key Lake, McArthur River, McClean Lake and Rabbit Lake. (Edwards 1988, Edwards 1992, Fielder 1998, Edwards and Oliver 2000, Edwards 2001) The latest project in the Athabasca Basin is the Cigar Lake project."

Jan 1, 2002

By Cathy Aimone-Martin, Brent Meins

A comprehensive instrumentation program was implemented at the Howland Hook Marine Terminal on Staten Island, NY during proximate underwater rock blasting in 2014. Forty-two blasts took place over a 4-week period to deepen the 1200-ft (366 m) Berth 3 from -45 ft (-14 m) to -50 ft (-15 m) MLW to accommodate Post-Panamax vessels. Approximately 86,000 yd3 (65,752 m3) were blasted 120 to 9 ft (37 to 2.7 m) from the wharf to a total depth of -57 ft (-17.4 m). Pre-blast planning included developing and implementing a comprehensive monitoring plan and setting vibration and strain limits to protect the wharf. The plan outlined methods to measure vibrations on five corners of four concrete deck sections, on five concrete-filled pipe piles just below the pile cap near deck corners, and in bedrock adjacent to pile sockets. Water overpressures were measured near instrumented piles for 19 blasts closest to the wharf. A total of 19 geophones were secured to the wharf structure and buried 12 ft (3.7 m) in drilled holes.

Jan 1, 2016

By D Lichti

This paper presents recent advancements in the MillMapper software technology, developed and used for thickness gauging of liners of cylindrical grinding mills used for mineral comminution. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces with millimetre accuracy. The paper is structured as follows. First, a review of the technology and its numerous advantages over existing techniques and the value it adds to operations are presented. These are followed by discussion of recently-implemented innovations, including improved visualisation and inspection tools, automatic ball charge volume measurement and automatic mill liner volume/weight measurement. Results from its application at several sites in Australia are presented throughout.

Jan 1, 2007

By Pupazzoni P. D, Meissner D. C

Incorporating an iron ore pelletising plant, a MIDREX'"' Direct Reduction Plant, and a mini mill, the conversion of iron ore fines to high- quality steel slabs in Western Australia is among the lowest cost routes in the world. The cost and availability of iron ore and natural gas, government support, and proximity to the growing Southeast Asian market all contribute to the competitive position of the area. Owing to the lead-time required, this is an ideal time to develop a new project to supply semi-finished steel to Asia for rolling to a finished product. A project contracted now will start up in about three years, when the market should have recovered.

Jan 1, 1999

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

The theme of the conference is "excellence", an epithet of special significance in tertiary education. It appears in the mission statements, goals and plans to achieve them of most, and quite possibly all, tertiary institutions in Australia. In the context of excellence, this paper examines the current statue of professional education in the principal mining industry related discipline of Mining Engineering. It furthermore, identifies and discusses a number of special problems in mining education that the tertiary sector has long endured. Some of these problems are becoming acute, and solutions will have to be found soon in order for the industry to be assured of the supply of well motivated and appropriately qualified young engineers and scientists necessary to achieve and maintain the excellent to which it aspires.

Jan 1, 1989

In order to maintain a production rate of 6,000 tonnes per day from underground at the Williams Operating Corporation, two independent mining areas were required which created a long narrow sill pillar between them. During initial mining of the sill pillar there were a number of significant ground falls [LeBlanc and Murdoch, 2000] and in March 1999, with no active mining ongoing in the sill pillar area, a rockburst of magnitude 3.0 Nuttli occurred. Extensive ground support was designed and installed to withstand events of similar magnitude [Bawden and Jones, 2002]. A mine wide microseismic system was installed to monitor mine induced seismic behaviour over the entire mine. The area most directly affected by the 1999 rockburst was rehabilitated using a highly ductile support design. Along with microseismic instrumentation, the areas were instrumented using conventional SMART Cables and SMART MPBX?s. Subsequent to this, the area was impacted by a large number of high magnitude seismic events [magnitudes between 1.7 and 3.5 Nuttli]. The ground support performed very well during these events, providing confidence in the mine?s ability to control the ground under severe rockburst conditions. Analyses of microseismic and conventional instrumentation, combined with numerical analyses of sequence alternatives, were used to develop an optimal mining strategy for the sill pillar area. The selected strategy involved utilization of instrumentation data and calibrated model results to analyze yield zones in the sill. The analyzed ?yielded? zones were assessed to be low seismic risk. Initial mining in the sill was then concentrated in these low risk areas, with the objective of further concentrating stress into the remaining seismically active area, in order to induce ultimate failure of the sill. Continuing large magnitude seismicity and resulting damage in the remaining ?high seismic risk? area, led to abandoning a second portion of the footwall access and the strategic decision to extract a stope near the centre of this zone in order to force final failure of the sill pillar. During execution of this plan two large magnitude seismic events occurred resulting in destressing and final failure of the remaining sill pillar. The paper provides a detailed description of this ?strategic mine sequence driven self-destressing process? and the implications to final extraction planning in this area of the mine.

Apr 1, 2005

By D. P. Roberts

This paper reviews the use of crush pillars on mines in the Bushveld Complex and the Witwatersrand Supergroup. Stress measurements were undertaken in order to determine the residual strength of these crush pillars. The results from these stress measurements are compared with previous attempts to determine the residual strength of crush pillars using back analysis. It is concluded that the residual strength of such crush pillars lies in a band between 13 MPa and 25MPa. Using the data from the stress measurements, as well as published and unpublished data, a stress-strain curve for a crush pillar with a width-to-height ratio of 2:1 is proposed. Where further work is required, this is indicated in the text.

Jan 1, 2005

By Z. van Zyl

The southern African coal industry is facing the reality that coal reserves are becoming deeper and harder to mine than before. Alternative visions need to be considered to offset the impact of these challenges on productivity, cost, and profitability. One of the main challenges is to maintain current production levels under more difficult conditions, and improve productivity where conditions allow. There is a need to move from the reactive event-based management system towards the more adaptable and flexible process-based management system. This paper focuses on underground coal mining, but the principles are also applicable to other commodities and mining methods. This paper is based on research undertaken by the personnel from Mining Consultancy Services Pty Ltd (MCS) on trends in the underground coal mining sector, as well as practical experience over a period of 16 years in the field of electronic monitoring of mining machinery and productivity optimization.

Jan 1, 2015

Study on the Effects and Mechanics of Na2SO3 to Chalcopyrite and Galena

Sep 13, 2010

At last year's. annual meeting of The Institute, Sir George Fisher, as President, compared it somewhat nostalgically with a meeting of its kind in the 1920s when comment was expressed on the decline of Australianmining and on the lack of new mineral discoveries.I feel that tonight's annual meeting is even more an occasion for nostalgia, for it represents the seventy-fifth anniversary of the founding of The Australasian Institute of Mining and Metallurgy. I hope, therefore, that I may be allowed to retrace some of the circumstances of this Institute's origin and at the same time to look at some of the broader happenings of those 75 years.From this distance in time it is, of course, much easier to get things in perspective and one of the things that compels enormous admiration in looking back over the history of our Institute is to note the qualities of foresight and keen concern for professional standards which moved the pioneers in this Institute. They had no benefit of hindsight to aid them.Just over 75 years ago, a small group of men met in Broken Hill to discus.s the possibilities of forming an association of mining engineers. The moving spirit was Uriah Dudley, our first secretary, manager of the Umberumberka mine at Silverton. The first formal move to form an association of mining engineers came from the Amalgamated Mining Managers Association of Australasia. At the time, this association was a fairly new group, being 5 years old.It had been formed to try to raise the standard of management throughout the industry. Uriah Dudley and our first provisional president, John Howell, held their first talks in 1891 and further meetings at Broken Hill followed. The inaugural meeting, attended by 200 members, was held in Adelaide in April, 1893.

Jan 1, 1968

By Lumley G, Rowlands D

The overburden slusher (OS) is proposed as a stripping tool that is expected to find application in overburden stripping operations including open cut coal and oil shale mines. OS is expected to combat the effects of increasing depth on the productivity of conventional dragline stripping.Although previously developed stripping techniques have included the use of drag scrapers the OS is sufficiently different as to constitute a new stripping method.A study undertaken at the University of Queensland during 1985 is believed to be the first major study on the use of the OS and preliminary economic results are very encouraging. It appears that the OS has the capacity to remove overburden at a cheaper unit cost than the equivalent powered dragline stripping machine at any comparable depth of overburden. The OS is not adversely affected by increasing stripping depth to the same extent as a dragline. In addition, the action of the OS machine allows for the lowering of spoil face angles, thereby reducing spoil slope stability problems encountered in deep open cut strip mines.

Jan 1, 1986

By F. D. Richardson

STAFF: Editor, Gerhard Derge Carnegie lnstitute of Technology Schenley Park Pittsburgh, Pa. 15213 Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Jack H. Scoff, President; Richard C. Cole, Past-President; Harold 0. Emerick, President-Elect; Ralph L. Hennebach, Treasurer; Robert W. Shearman, Secretary; Donald A. Parks, Assistant Secretary; Leslie S. Wilcoxson, Assistant Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairman; T. E. Dancy, H. O. Emerick, P. R. Gouwens, R. E. Grace, J. H. Jackson, H. H. Johnson, A. E. Lee, Jr., R. R. Nosh, R. D. Pehlke, and Paul Queneau. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extroctive Metallurgy Division: R. E. Grace, Choirmon; G. M. Bell, D. W. Bridges, J. M. Cigon, G. W. Heoly, T. A. Henrie, R. D. (Holli-doy, C. E. O'Neill, C. S. Somis, A. W. Schlech-ten, and Charles Shull. Iron and Steel Division: R. D. Pehlke, Choirmon; T. P. Floridis, Arnulf Muon, G. R. St. Pierre, E. T. Turkdogan, L. H.Von Vlock, and J. M. Uys. lnstitute of Metals Division: H. H. Johnson, Jr., Chairman; J. B. Clark, Vice Choirmon; M. R. Achter, G. F. Bolling. J. O. Brittoin, G. P. Conard, II, R. S. Davis, L. A. Girifolco, G. T. Hohn, J. P. Hirth, L. Himmel, G.T.horn, George Krauss, J. D. Livingston, R. D. Manning, H. M. Otte, S. V. Rodcliffe, R. E. Reed-Hill, H. C. Rogers, E. ScaIa, O. Sherby, M. T. Simnad, G. R. Speich, E. A. Steigerwald, R. A. Swolin, W. A. Tiller, W. R. Upthegrove, J. B. Wagner, Jr., Derek Wolton, H. W. Weart, W. W. Webb, and D. Published seven times yearly in February, March, April, June, August, October, and December by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street New York, N. Y. 10017. Telephone PLAZA 2 -6800. Subscription $30 per year for non-AtME members m United States and North, South, and Central America; $32, foreign; $7.50 for AlME members Single copies, $6.00, single copier foreign, $6.50. The AiME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1964 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AiME New York Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts. Second dost postaas poid ot New York, N. Y.,ond Ann Arbor, Mich. Volume 230, Number 6.

Jan 1, 1964

The object of this paper is to give a description of the new office and changehouse building and equipment at the Zinc Corporation Limited, the office section of which has now been in full use for approximately three years, and the changehouse section for approximately two years. As the expectations of the design have been fully realized, it is thought that this description will be of interest to members and possibly of some use to others faced with similar problems.GENERALIn the centralization of the surface plant around the new main shaft the combined office and changehouse building forms a prominent feature, being located between the shaft and the mill and facing the workshops on the northern side.The scheme for housing all employees in one building was proposed by the Manager, Mr. A. J. Keast, who was familiar with a similar successful structure built at the McIntyre Porcupine Mines Ltd. in Ontario, Canada.The principal features of this building were adopted as a basis for design, and the present layout evolved to suit the particular requirements of this mine.Some of the advantages of the design are:(a) Economy in first cost and space occupied when compared with plants having separate office and changehouse buildings.(b) Easier and more constant supervision of employees and of the plant by the senior staff members.(c) Close contact between officials of all departments.(d) Close covered connection between changehouse and shaft.(e) Avoidance of duplication of ,essential services such as electric power, water, heating plant, sewerage, etc.The Managing Director, Mr. W. S. Robinson, further instructed that the following requirements be adhered to in the new building:(a) Ample accommodation to be provided for office staff and other employees.(b) Special attention to be paid to lighting, both natural and artificial.(c) Working temperatures to be controlled to facilitate comfort and efficiency.(d) The buildings and equipment' to be of a permanent nature with furnishings and fittings of modern design.

Jan 1, 1941