Search Documents

By A J. Morrison, K Demir, J Kohmuench, K Runge, C Evans

The Eriez HydroFloat® is a flotation device capable of recovering significantly coarser and lessliberated particles than is possible using a conventional mechanical flotation cell. Originally developed for industrial and bulk mineral beneficiation, the HydroFloat® is attracting increasing interest as a means of increasing the required grind size for metalliferous ore flotation. Doing so would reduce the costs of processing complex ores, either by decreasing the energy required to grind the flotation feed or by increasing the throughput achievable with a given comminution circuit. Processing coarser particles would also result in coarser waste streams, potentially improving the mechanical and hydraulic performance of the waste dams that they are sent to. Recent work at pilot – and industrial-scale has proven the potential of the HydroFloat® technology to achieve these gains in metalliferous applications. However, in order to realise the full potential of the HydroFloat® technology, it is necessary to understand not just its performance but also the drivers for that performance. Doing so will allow the design and operation of HydroFloat® devices to be optimised for different ores and applications. For this work, a HydroFloat® pilot rig was deployed to a coppergold plant in Australia and was used to investigate the effect of stream and operating conditions for treating the tailings stream of one of the plant’s rougher flotation cells. Under each set of operating conditions, samples were taken of the HydroFloat® feed, tailings and concentrate streams, and processed to yield the grade and recovery achieved by the device. At the same time, the bubble size and bed behaviour inside the device were measured. This paper presents preliminary relationships observed between the operating conditions and the performance of the HydroFloat® cell, and thus suggests a range of possible drivers for the measured coarse particle flotation performance.

Aug 24, 2022

By M Hilden, K Barbosa, M Yahyaei, C Ndimande, K Runge, V Jokovic

Classification devices provide a link between comminution and flotation. Basically, it determines which particles are diverted back for additional grinding and which ones pass to downstream flotation. Therefore, the classifiers play an important role in the performance of a mineral processing circuit. Hydrocyclones are the most common classifiers used in wet grinding, despite being associated with poor classification efficiency. Hydrocyclones are widely used due to advantages related to low maintenance as well as reduced capital and operating cost. Other classifiers, such as fine screens, have much better classification efficiency compared to hydrocyclones. The major challenge of using screens in an operation, however, is their large footprint and increased maintenance requirements relative to hydrocyclones. Some researchers have demonstrated that switching from hydrocyclones to screens, as the classifier device in a ball milling circuit, resulted in a 20 per cent increase in plant throughput and significant improvements in coarse particle recovery, resulting in a 6 per cent increase in overall flotation recovery. However, it is known that these benefits of improved classification are very much ore specific, ie depending on the ore response. Therefore, there is a need to estimate the benefits of improved classification in pilot scale testing before the plant could consider the potential classifier upgrade. This paper presents the results of two pilot-scale grinding tests where the ore sample was processed using different classifiers: a traditional hydrocyclone and hybrid classification involving the use of a semi-inverted hydrocyclone followed by a screen. The size specific energy and circulating load were used to compare the performance of the grinding circuit. The grinding product was subject to mineral liberation analysis and the impact of classification efficiency on the mineral liberation is discussed in the paper.

Aug 24, 2022

By R W. Henley, L Knuefing, M Turner, Y Zhang, M Saadatfar, A Limaye, R Cruikshank, M A. Knackstedt, A Kingston, L Beeching, N Francois

A better understanding of ore fragmentation and the textural features of ore is a key to the energy efficient extraction of targeted minerals from low-grade ore deposits. In this study, X-ray microcomputed tomography (micro-CT) is employed to study mineral liberation during the tensile failure and onset of fragmentation of a copper ore. Our results show that X-ray micro-CT could inform new studies of ore micromechanics and fragmentation at the laboratory scale and may offer new avenues to address current challenges in the design of efficient comminution processes. We present the results of experiments based on a high-pressure apparatus enabling micromechanical studies to be carried out in situ (inside a micro-CT scanner). This platform produces high-quality 3D images of the evolution of a sample of porphyry copper ore during an in situ fragmentation test. A sequence of tomographic images enables mapping in 3D of both the deformation of mineral phases and the fragmentation process. The fragmentation occurs quasistatically through multiple stages starting with an initial tensile fracture splitting the ore diametrically, followed by tensile-activated nucleation and growth of multiple fractures producing a complex fracture network. Coupling breakage with microstructural information enables quantitative determination of the impact of ore texture heterogeneity on fracture patterns and mineral liberation. This microstructural information can be compared to key measurements of the ore mechanical behaviour such as the global deformation energy, strain deformation field and the stress relaxation response. The latter allows one to identify interesting precursor signals of the tensile failure. The copper liberation, fragment size distribution and breakage patterns are statistically characterised and related to comminution mechanisms which are clearly identified in the sequence of tomographic images. The two dominant mechanisms are rock-rock friction/compression induced by fracture closing and compression-driven fragmentation at rock-crusher contact points.

Aug 24, 2022

By K Haga, G Danha, A Shibayama, L L. Godirilwe

The hydrometallurgical separation and enrichment processes provide an effective way to selectively recover metals from relatively dilute multicomponent sulfuric acid leach solutions. The multicomponent leach solution utilised in this study contained 0.3 g/L Cu, 0.34 g/L Ni, 0.13 g/L Co, and 2.96 g/L Fe, which was obtained after high-pressure oxidative acid leaching (HPOAL) of the copper-nickel smelter slag. The solvent extraction (SX), precipitation, and xanthate complexation processes were employed to recover and upgrade Cu, Ni, and Co from the leach solution. Batch SX tests were carried out using a countercurrent two-stage mixer settler extraction column, and LIX 984N (10 per cent v/v) as a copper extractant. Fundamental parameters influencing the extraction process such as pH, mixing speed, H2SO4 concentration, and organic/aqueous (O/A) phase ratio were investigated. For copper enrichment in solution, a combination of two extraction stages and two stripping stages were employed. Copper was successively separated from Fe, Ni, and Co under optimised extraction conditions (pH 2, 400 rev/min, O/A 0.25, and 20 min contacting) and stripping conditions (175 g/L H2SO4, 400 rev/min, O/A 4, and 20 min contacting). About 97 per cent of copper was extracted with low co-extraction of Fe, Ni, and Co of about 5.90 per cent, 1.47 per cent, and 2.53 per cent, correspondingly. A final Cu-rich solution containing 23 g/L Cu was obtained with a very low Fe concentration of 0.05 g/L. Additionally, for iron removal from the Ni/Co raffinate solution, more than 99 per cent of iron was precipitated at pH 4 by the addition of a calcium carbonate (CaCO3) suspension, with low co-precipitation of nickel and cobalt of around 3.68 per cent and 2.27 per cent, respectively. Furthermore, about 83.6 per cent of nickel and 99.4 per cent cobalt were co-precipitated from the solution by potassium amyl xanthate (PAX) solution at pH 6. The Ni and Co xanthate complexes were thermally decomposed and recovered as cobalt oxide (CoO) and nickel sulfide (NiS) solids.

Aug 24, 2022

By M Saghaeian, M Zare, V Sheikhzadeh, R Hejazi

High-Pressure Grinding Roll (HPGR) is one of the efficient methods for increasing the specific surface area (SSA) of iron ore concentrate for pellet feed production. HPGR grinding mechanism implies that material should compressed between the two rolls, therefore layer of material must be able to resist required pressure for achieving suitable grinding conditions. In this study, by doing SSA increasing tests with pilot HPGR, the effects of silica reduction on SSA increasing results were investigated. For this purpose, HPGR tests were performed on an Iranian magnetite concentrate before and after reverse flotation silica reduction tests. Based on the laboratory test results, silicates have been concentrated in two fraction sizes of the sample comprises coarser than 150 microns in form of quartz and finer than 7 microns in form of iron silicates. These silicates have been effected on reduction of concentrate bed pressure resistance by creating a pasty and sticky mud. In this condition, HPGR cannot work properly and operation results are not acceptable. According to flotation silica reduction tests, with 90 per cent weight recovery, concentrate Fe grade is increased from 67.8 per cent to 69.5 per cent and SiO2 content is reduced from 1.98 per cent to 0.9 per cent and especially for lower than 7 microns fraction size, as a critical fraction, SiO2 content decreased from 4.45 per cent to 2.35 per cent. HPGR tests were performed on 8 per cent moisture in 4 N/mm2 specific force and according to the results after silica reduction HPGR operation conditions are optimised. Results showed that the working gap increased from 7 to 10.5 mm and specific throughput of material raised from 180 ts/hm3 to 250 ts/hm3 , and SSA increased by 300 cm2 /gr in a single pass.

Aug 24, 2022

By A Jyoti, J R. Black, R R. Haese, E O. Ansah

Copper (Cu) is a critical metal in the transition to a low-carbon power supply. Presently, low-grade copper sulfide ores account for almost 80 per cent of the global reserves. Large amounts of water are required to process these low-grade copper ores. The mining industry utilises lixiviants from recycled water from different sources to conserve water, whilst enhancing Cu recovery. Some utilise intermediate to pregnant leach solutions, sea water, and processed water from electrowinning circuits with highly variable concentrations of ions. Previous studies have highlighted the formation of precipitates that passivate the surfaces of minerals in these low-grade copper ores and/or block flow paths for lixiviant during heap leaching. In this study, we utilised concepts of phase replacement to devise an innovative means of controlling precipitation and increasing copper recovery using industrial brine as opposed to freshwater. We propose the formation of Al-rich phases (such as AlSO4 + or alunite) to replace iron sulfate and iron hydroxysulfates (such as jarosite) during the chalcopyrite dissolution-precipitation mechanism. The rationale is to have available Fe3+ throughout the chalcopyrite leaching process. We tested this method by carrying out various batch experiments using CaCl2, AlCl3, and NaCl industrial brine types compared to freshwater and explored the capacity to leach Cu from chalcopyrite. There is higher Cu recovery during oxidative leaching of chalcopyrite in industrial brine with 91 per cent recovery using AlCl3-rich brine, 84 per cent with NaCl-rich brine, and 56 per cent with CaCl2-rich brine as compared to 35 per cent recovery using freshwater. In the absence of Al3+, various forms of iron sulfates, and jarosite are formed, reducing the availability of Fe3+ for chalcopyrite dissolution. The introduction of Al3+ leads to the formation of AlSO4 + species, thus lowering sulfate activity and the tendency for K-jarosite formation.

Aug 24, 2022

By A Yáñez, P Vallejos, R Grau, J Yianatos

In flotation cells, especially in large flotation units, froth management is a crucial variable that should be considered during the design phase or optimised to improve the performance of existing flotation circuits. This paper presents a simulation evaluation of the effect of launder design on the metallurgical performance of an industrial flotation circuit consisting of five TankCell® e630 (630 m3 ) cells in a Cu rougher duty. This analysis was carried out using a new industrial simulator, which was built on a wide database collected from many industrial concentrators. This tool is currently incorporated into HSC Chemistry® software and allows evaluation of the effect of launder design on mineral froth recovery, water recovery, entrainment, and other variables to be quantified. The industrial flotation circuit was evaluated under different launder design scenarios, considering an actual flotation circuit that includes TankCell® e630 cells for calibration and as a reference (baseline). Firstly, two different designs were evaluated in the full circuit: a standard launder design and a new launder technology. It was found that the new launder technology enabled improvement of the mineral recovery along the circuit, mainly for coarse particles, due to the improvement in froth mineral recovery. Next, the partial upgrade of the launder design along the circuit was analysed. Thus, the new launder technology was evaluated in the first and the last two cells of the bank. The results showed that upgrading the launders in different cells along the circuit delivered an increase in the final recovery with respect to the baseline, with a partial impact on the concentrate grade. However, these changes are less than those when evaluating the full upgrade scenario. A partial launder upgrade either in the first or last two cells of the bank showed similar final recoveries, but the latter enabled a slightly higher concentrate grade (about 1 per cent higher) to be achieved. Finally, the evaluation of launder design using the industrial simulator made it possible to estimate its effect on variables that are not commonly obtained from plant surveys, including froth recovery per particle size, collection recovery per particle size and liberation, gangue entrainment and bubble loading grade.

Aug 24, 2022

By G Bournival, Y Pan, S Ata

A custom-made set-up that measures bubble coalescence time and the thin film balance (TFB) technique were used to explore the role of residual xanthate (potassium amyl xanthate, PAX) and salt (NaCl) on the adsorption of two frothers (methyl isobutyl carbinol-MIBC, and di-propylene glycolDPG) at the air-water interface. This paper is primarily focused on the comparison of these two techniques in studying the interaction between the flotation reagents and salt emphasizing their capabilities and limits. The results from the coalescence rig showed that the presence of PAX improved the stability of bubbles in both frother solutions and led to a bubble coalescence inhibition at 50–500 ppm DPG. These measures were compared with the results from the TFB. Findings from the TFB were overall in good agreement with the bubble coalescence time, but a higher stability level was observed in thin films under the same condition. The effect of salt on the frother and PAX mixture was also explored, and the results showed an adverse impact of the salt on the interaction of frother and PAX with both techniques. However, variations were found between them in some cases. The TFB is much more sensitive to the presence of dissolved gas and oil droplets.

Aug 24, 2022

By X Zhang, Y Zhu, P E. Ngoepe, P P. Mkhonto, W Xiong, L Han, L Lu

The triazine molecules have not been given much attention and they are potential collectors that may positively impact the mineral processing industry. The adsorption of triazine as collectors such as sodium 2,6-dithio-4-butylamino-1,3,5-triazine (SDTBAT) on pyrite form a basis in design of flotation collectors that may be applicable in a wide range of sulfide minerals. The SDTBAT collector was compared with the sodium normal butyl xanthate (SNBX) and sodium normal butyl dithiocarbamate (SNBDTC). All collectors were adsorbed in their neutral form containing sodium on the pyrite (100) surface. The computational calculations found that the adsorption energies followed the order: SDTBAT (-300.35 kJ/mol) > SNBX (-186.10 kJ/mol) > SNBDTC (-163.78 kJ/mol). It was observed that the SNBX and SNBDTC adsorbed through the S atoms, while the SDTBAT adsorbed through the S atoms and N atoms onto Fe atoms. It is clear that the SDTBAT had a strong binding energy which is attributed to the presence of the triazine group that is electron depositing to the active S atoms compared to the SNBX which possessed the oxygen that is electron withdrawing. Moreover, the SDTBAT collector was found to bind stronger than the xanthate. This was complimented by microflotation tests that showed fast floating and higher recoveries of pyrite when using the SDTBAT collector than the xanthate and DTC. This clearly demonstrated that the SDTBAT is a potential collector to replace the xanthate collector due to its high selectivity and flotation power.

Aug 24, 2022

By M Yvon, S Parkes, K P. Galvin, P Wang

Mineral liberation is critical to maximise the grade and recovery of nickel, however this objective is challenged considerably by the poor flotation kinetics, especially that of ultrafine particles (Kelebek and Tukel, 2018; Multani and Waters, 2019). High recoveries demand long cell residence times and hence a large flotation capital expenditure (Wills and Finch, 2016). However, this leads to excessive entrainment of gangue minerals, thus negating efforts to depress its recovery. This study aimed to investigate new hydrodynamic approaches to improve nickel flotation, focusing primarily on unrecovered nickel from a Western Australian tailings stream. Mechanical cell flotation experiments were conducted to understand the flotation kinetics, covering different size ranges. A novel Reflux Flotation Cell (RFC) was also used to improve the nickel recovery and reject the silicates. Future work aimed at applying the RFC to different size portions is also outlined.

Aug 24, 2022

By B McFadzean, N P. Lima, D A. Deglon

The reverse flotation of Itabirite iron ore is typically performed after a desliming step in which most of the sub-10 µm particles are removed. This is done to limit processing problems such as poor flotation recovery of SiO2 due to slime coatings and increased slurry viscosities, unmanageable froths and increased losses of hematite particles due to entrainment. However, the rejection of ultrafine particles contributes to large losses in iron recovery and may contribute to the instability of tailings dams. The aim of this study is to decouple the effects of ultrafine particles in the pulp and froth phases to better understand the processing capabilities of the fines fraction. The flotation test work was performed in a special-purpose continuously operated laboratory flotation cell that has a deep froth section to simulate plant-scale froth conditions. Five conditions of fines addition were investigated at three different froth heights and a solids concentration of 50 per cent. The behaviour of the pulp and the froth were decoupled using froth stability and froth recovery tests. This showed that, even though there is an exponential increase in froth stability at increasing fines quantities, the performance of the pulp has the overriding effect on the overall SiO2 recovery. Pulp zone, froth zone and overall SiO2 recoveries showed that overall recoveries increased by about 3.6 per cent for every 1 per cent decrease in fines content. This meant a large increase of 20 per cent in SiO2 recovery when going from undeslimed to deslimed feed. This was driven largely by increases in the pulp zone recoveries, which were about 4 per cent for every 1 per cent decrease in fines content. The froth recoveries, on the other hand, decreased by between 0.75 per cent and 2.5 per cent for every 1 per cent decrease in fines content, depending on froth height. This paper explores further insights into iron ore flotation processing at different slimes concentrations.

Aug 24, 2022

By I Zh Bunin, V A. Chanturia, V G. Minenko, M V. Ryazantseva, A L. Samusev

A promising source for the extraction of rare metals and REEs in Russia is the eudialyte ores of the Lovozero deposit, which do not contain active uranium components. The eudialyte ore reserves of the Lovozero Massif are considered virtually unlimited and therefore have the potential to become a primary source of a number of rare and rare earth metals. The goal of this study was to comprehensively examine the effect of the parameters of high-power nanosecond electromagnetic pulses (HPEMP) and dielectric barrier discharge (DBD) on the leaching performance of eudialyte concentrate and the selective separation of zirconium and REEs from productive solutions. Using scanning electron microscopy and infrared spectroscopy, the mechanism behind the intensification of acidic dissolution of eudialyte as a result of pretreatment with energy impacts was described. During the HPEMP treatment, weakening and destruction of the eudialyte surface was observed, which at the substructural level is expressed in the deformation and local destruction of Si10O27, Si9MO30 resulting in formation of microcracks. During the DBD treatment, the formation of characteristic defects was observed in the form of imprints of dielectric breakdown microchannels and individual mineral fragments. Pretreatment of eudialyte concentrate using HPEMP made it possible to increase the recovery of zirconium into the pregnant solution of leaching by 3.4–4.3 per cent (from 86.6 per cent to 90.9 per cent) and by 4.1 per cent (from 86.6 per cent to 90.6 per cent) when using DBD. The increase in the total recovery of REEs was 1.2–1.8 per cent (from 87.7 per cent to 89.2 per cent). The effect of pH values, solution temperature, initial concentrations of valuable components on the successive recovery performance of zirconium and REEs from the pregnant solutions nitric from the acid leaching of eudialyte concentrate by chemical precipitation was examined. The possibility of selective separation of the zirconium product and rare earth elements with a zirconium recovery of 99.95 per cent and a REE recovery of 87.5 per cent was established. REE loss with the zirconium product was 8.0 per cent and 4.5 per cent with the spent pregnant solution.

Aug 24, 2022

By D K. Weatherley, A N. Mainza, I Govender, L M. Tavares, M S. Powell

It is understood that rocks do not instantaneously transport along a grinding mill and are consequently not perfectly mixed, but this is conveniently overlooked in mill modelling. A lack of understanding of the transport phenomenon and the difficulty of modelling realistic transport in a complex tumbling system, contribute to this. Visual observation of segregation in AG and SAG mills and measured lag time of mill response to changes in feed provide evidence of the influence of axial transport within mills. Incorporating this lag in dynamic models should underpin dynamic simulation of milling circuits for design and for model-based control. Limitations and errors in predicting the influence of increased power via mill length versus diameter, inability to predict pebble production, and a lack of the differential in residence time across rock sizes and competences, all contribute to inadequate design prediction that can be especially acute for large Autogenous mills. Examples of dramatically under – and overloaded pebble regrind circuits and the inability to predict pebble load in AG milling discouraging the application of this energy-efficient option, point to the need for predictive modelling of breakage by competence linked to transport through and out of mills. Incorporating progress in granular flow and mixing, coupled to computational advances enable models to be based on complex breakage and transport models at high spatial resolution. This allows mechanistic models to simulate thousands of times faster than real time, opening the door to more accurate mill design, including dynamics in process simulation and to live simulation for process control – all with advanced mechanistic models. The value of grasping this opportunity is not easily refuted.

Aug 24, 2022

By P G. Bourke, A Yáñez, G J. Jameson, N M. L Kupka

The kinetics of fine and ultrafine particles in conventional mechanical flotation cells are limited (Feng and Aldrich, 1999; Trahar, 1981; Wang et al, 2016). Accordingly, even limited recoveries with such machines require long residence times. Theoretical investigations into the rate of capture of fine particles by flotation, have indicated that a key parameter is the rate of shear in the fluid surrounding the bubbles and the particles. Achieving fast flotation rates of ultrafines requires a new method of bringing the particles and bubbles into contact, utilising the beneficial properties of highly dissipative flows to break through the water boundary layer. In 2010, a new type of flotation cell known as the Concorde Cell was described, in which bubbles and particles are brought together in a sonic shock wave (Jameson, 2010). Earlier research had shown that when a dispersion of fine bubbles in liquid passed through a converging nozzle at the local speed of sound, the resulting shock wave downstream generates a mass of even finer bubbles in the flow as it passes through the shock wave. The fluid within the shock wave is highly turbulent, and an environment is created that is very favourable to particle-bubble collision and capture. In this paper, we briefly describe the Concorde Flotation Cell and give examples of its use.

Aug 24, 2022

By J Zhou, L Crompton, K P. Galvin, J L. Sutherland, C P. Lowes, C Bezuidenhout, J Bijzet

Platinum Group Metal (PGM) bearing ores from the Upper Group 2 (UG2) reef often contain significant concentrations of chromite which can potentially be upgraded to produce a saleable product. A common approach is to implement gravity separation on the PGM flotation circuit tailings. However, where the particle size range of interest is broad and the lower size limit ultra-fine, the challenge is how to maximise the recovery at a saleable product grade without compromising throughput. This study was concerned with the performance of a REFLUX™ Classifier for beneficiation of a PGM bearing chromite ore and the benefits of size classification. The sample had a nominal top size of 0.5 mm and was processed over the complete size range and in two discrete size classes following classification at 106 µm. The primary goal was to produce a concentrate exceeding 40 wt. per cent Cr2O3, ideally approaching 42 wt. per cent Cr2O3, with minimal PGM losses above 106 µm. A major challenge was to process at the required solids throughput in a single stage with the feed pulp density constrained to a nominal upper limit of 30 wt. per cent solids. It was found that varying the controller density set point of the REFLUX™ Classifier produced strong control of the product grade. Products as high as 41.1 wt. per cent Cr2O3 were produced at 78.6 per cent recovery for the +106 µm material, while in the −106 µm portion the product grade was as high as 41.4 wt. per cent Cr2O3 at 83.2 per cent recovery. Processing the feed in discrete size classes enabled the volumetric feed and fluidisation rates to be optimised for a given application; hence, superior performance was achieved at the finer sizes. This work has demonstrated the value in considering feed preparation as well as technology selection in developing a robust process solution.

Aug 24, 2022

By T Perera, B Fan, S Thang, T Hsia

The mining industry is currently focusing to develop and adopt sustainable collector chemistry that can efficiently recover valuable minerals from their natural state. However, a limited number of research can be seen on the design and synthesis of polymeric flotation collectors. The focal objective of this research is to synthesise a more effective polymeric collector with advanced architecture to utilise in the mineral processing industry. Reversible Addition-Fragmentation Chain Transfer (RAFT) co-polymers with cardanol derivatives have the potential to selectively trap valuable metals in the flotation process in a more efficient way. Cardanol exhibits amenability to chemical modification for making tailor-made monomers that can further produce polymers with high value. The synthesis of a series of fit for purpose copolymers in this study was accomplished by RAFT polymerisation. The ability to design complex architecture is a significant advantage in engineering polymeric collectors by RAFT polymerisation. Initially, commercially available cardanol was converted to a cardanol based monomer and copolymerised with commercially available monomers to synthesise a series of novel cardanol based copolymers with predetermined molecular weights. The side groups of the copolymer were chemically modified to incorporate functionality that can be selectively adsorbed on the chalcopyrite surface.

Aug 24, 2022

By E A. Agorhom, M Beyuo, C Owusu, I Quaicoe

Understanding the mineralogy and liberation of gold particles in an ore is key to the development and optimisation of gold processing operations, being cyanidation or gravity separation. This can be achieved through basic historic geological information, gold deportment studies, chemical speciation and metallurgical test works. The present study assessed the nature of the occurrence of gold particles (mineralogical composition, liberation, associations and surface chemistry) and its effect on the process route (cyanidation and gravity separation) of a typical paleo placer gold ore deposit within the Tarkwaian Rock system. The investigative approach used involved chemical assay, quantitative X-ray diffraction (QXRD) and quantitative evaluation of minerals using scanning electron microscopy (QEMSCAN). The ore samples (A, B, C, D, E, F) used were obtained from six active pits of a gold mine working on this orebody. The results of the mineralogical analysis revealed that the ore is highly oxidised and comprised quartz (>80 per cent) and Muscovite mica (>6 per cent) as the major mineral phases in all the samples. Trace amounts of hematite, kaolinite and todorokite were also identified in all the samples. The chemical analysis showed presence of gold (Au) in all the samples with samples B (3.62 g/t) and C (3.96 g/t) containing the highest concentrations. Trace amounts of copper (Cu), iron (Fe), sulfur (S), aluminium (Al), arsenic (As) were also detected in all the ores. The QEMSCAN mineralogical liberation and gold association results revealed that the gold grains were relatively coarser in all samples (P80 > 80 µm Au in size) except F (P80 < 32 µm Au in size). Gold grains were highly liberated especially in sample B with the majority of the locked gold grains forming complex associations. All the samples responded well to cyanidation and gravity separation except samples C and F, respectively.

Aug 24, 2022

By M Chen, W S. Ng, Y Liu

In the processing of refractory gold-bearing sulfides, pressure oxidation (POX) is commonly known for its role in liberating the gold in solid-solution via oxidation of the sulfide occlusions. For deposits that contain arsenic-bearing species including arsenian pyrite and arsenopyrite, POX serves an important secondary function in the fixation of arsenic, via the hydrothermal precipitation of stable arsenates such as scorodite and basic ferric arsenate sulfate (BFAS). There have been various investigations on the impact of different POX conditions on arsenic precipitation and the stability of the formed phases, but less is known about the changes to the arsenic carrier that occur in the curing stage, which follows directly from POX. The primary function of curing is to coax the dissolution of sulfates to reduce lime consumptions during cyanide leaching, and the slurry is kept at elevated temperatures near 100°C to achieve this. While the arsenic-bearing phases are expected to undergo transformation during this stage, there has thus far been limited experimental evidence. In this study, the effect of curing time and curing temperature on the arsenic-bearing species and arsenic deportment in the POX product has been investigated. Leaching of the curing products was also conducted to examine the stability of the arsenic species in the solid precipitates.

Aug 24, 2022

By N Esmaeili, M Saghaeian, L Hosseini, V Sheikhzadeh, R Hejazi

Ore roasting has long been used for beneficiation and assay upgrading of different ores. In this process, which is mainly used for sulfide ores, the ore is heated to a high temperature. More specifically, it is a metallurgical process involving gas-solid reactions at elevated temperatures. Some types of Iron ore are weak in magnetic properties. Hematite, goethite and limonite are classified in this group. Unlike magnetite, which shows strong magnetic susceptibility, these ores are hard to beneficiate through magnetic separation route. Many researches have focused on gravity separation and flotation routes for upgrading these ores and these methods have also been utilised in the industry. One of the methods to whose industrial application less attention has been paid is magnetising roasting in which the non-magnetic iron ore is transformed to magnetite which is further beneficiated through magnetic separation. In this study, magnetising roasting tests have been performed on one goethite sample in order to check the feasibility of using this method for this specific ore in industrial scale. It is worth mentioning that high intensity magnetic separation have been performed on this sample before but the achieved results were not promising. Results have revealed that through magnetising roasting magnetite content of the ore could be increased from 1.7 per cent up to about 25 per cent. FeO content of the feed sample was increased from 1.03 per cent up to around 9.25 per cent. Also optimum size distribution for achieving the best results in magnetising roasting for this sample has been determined through this study. The best results were achieved when the ore size was 0–10 mm. The effect of coal ratio, time and temperature on the process have also be studied. A coal ratio of 5 per cent, time of 30 min and a temperature of 850°C were determined to be the optimum conditions. Finally, the technical feasibility of utilising magnetising roasting for this specific ore has been confirmed.

Aug 24, 2022

By M Saghaeian, A H. Baladastian, A Dehghani Ahmadabadi, V Sheikhzadeh, R Hejazi

With the declining of high-quality hematite and magnetite iron ore reserves and the increasing accumulation of material resulting from mining and beneficiation operations that appear as lowquality depots and discharged materials in tailing dams, the necessity of recycling these reserves is increasingly becoming a critical demand. The Chadormalu iron ore mine is among the largest deposits of magnetite-hematite iron ore in Iran. In this mine, the total wet processing tails accumulated in tailing dams are over 92 Mt containing 25–40 per cent Fe. Laboratory and pilot tests on tailing samples led to the design and implementation of the Chadormalu Tailing Recovery plant (CTR) with a unique process circuit in Iran. In the CTR plant, after three steps of re-pulping with spiral classifiers and sanding machines, the underflow is concentrated by two stages of WMIMS and produces 64 per cent Fe grade magnetite concentrate. The tailings of the drums are mixed together and introduced into the hematite recovery section, including two stages of VPHGMS separators, and 60 per cent Fe grade hematite concentrate is produced. This plant has been in operation for over ten years with a total yield of 18.93 per cent. Due to changes in the materials extracted through new tailing dams, the quality of the final concentrate dramatically dropped to 56.36 per cent Fe and 0.79 per cent P; therefore, applying reverse flotation and removing phosphorus from the final concentrate was inevitable. By using this approach, upgrading of the concentrate to 63.01 per cent Fe and 0.05 per cent P was obtained. Furthermore, regarding the high amount of phosphorus in the tailing streams, direct flotation has been designed to produce apatite concentrate as a by-product stream through a flotation system comprising series banks of Rougher, Cleaner, and Re-Cleaners flotation cells. Hence based on the results, at optimum conditions, a final apatite concentrate with a yield of 15.78 per cent and 14.06 per cent P could be achieved. Successful implementation of this project has led to the production of magnetite-hematite and apatite concentrates with annual capacities of 250 000 and 45 000 t, together with total yields of 11.59 per cent and 6.19 per cent (includes de-sliming of apatite flotation feed), respectively.

Aug 24, 2022