Search Documents

By V. I. Lakshmanan, R. Roy

Base metals and PGMs are currently recovered from sulfide concentrates using pyrometallurgical processes. These processes suffer from several limitations such as being capital intensive, scaling problems, S02 emissions and long delay in value recognition. Alternative hydrometallurgical technologies have so far not been successful and currently total pressure oxidation and partial pressure oxidation hydrometallurgical technologies are being evaluated. Process Research ORTECH has developed a unique hydrometallurgical process to recover base metals and precious metals using mixed chloride technology. In a first stage leach, base metals are recovered and elemental sulfur is liberated from hydrogen sulfide formed during this leaching stage. During second stage leach, precious metals are recovered using proven separation technologies. Some of the advantages of the process are the recovery of elemental sulfur from sulfide sulfur, recycle of the chloride lixiviant thereby eliminating effluent treatment steps and use of excess energy from the Claus reactor for the pyrohydrolysis step.

Jan 1, 2011

By C. M. Díaz, P. J. Mackey, P. Coursol

In a recent paper [1], the present authors discussed calculated energy consumption numbers in copper sulphide concentrate smelting for four different smelting technologies. For the present study, from among these technologies, they selected the Noranda/Teniente continuous bath smelting followed by Peirce Smith (PS) converting route to investigate the impact on total energy requirement of some key process variations, such as tuyere injection of dry concentrate vs. slingering of wet concentrate over the molten bath, continuous converting vs. conventional batch PS converting and commercially proven slag cleaning alternatives. In their calculations, the authors used the same thermochemical model and methodology used in their earlier paper. This approach to explore plant design options provides an interesting basis for evaluating flowsheet modifications that could lead to significant copper smelting energy savings. The METSIM software was used in the present paper to carry out heat and mass balance computations for 8 different flowsheet configurations. The results are presented and discussed in the paper with respect to copper recoveries, energy requirements and CO2 emissions.

Jan 1, 2011

At long last, mining is on the rebound in Minnesota?s Iron Range and the excitement is starting to show. The SME Minnesota Section?s annual meeting was once again held in the heart of Iron Range country, at the Duluth Entertainment and Conference Center on the Duluth waterfront. The conference boasted a record attendance of 475 people and its largest-ever trade show. Appearances by Governor Mark Dayton?s new Iron Range Resources & Rehabilitation Board (IRRRB) appointee, Tony Sertich, as well as a local Fox news crew (see clip on SME website [link: http://fox21online.com/news/duluth-mining-conference-breeds-optimism-tech-innovation]) made clear that a lot of eyes [ ] are on the industry as it dusts itself off from the 2008-2009 recession. While the early years of the 21st century were very good to the Iron Range, the global drop in commodities prices and production left many companies reeling and brought back bad memories of the collapse of the industry in the 1980s. However, two years of solid growth and a rebound to above pre-2008 production levels have let the Minnesota mining industry to relax a little and talk seriously about long-term growth and stability.

Jan 1, 2011

By Harry Schnabel

A 6200 m² cement deep soil mixed (CDSM) wall was constructed for an addition to the Museum of Fine Arts in Boston, Massachusetts. The addition was located along the east side of the existing museum within an existing courtyard and in the area of a recently demolished structure. The basement for the new addition extended up to 9.1 m below the floor slabs of the adjacent buildings. The adjacent buildings are supported on a variety of foundations including; shallow spread footings on alluvial sand deposits, low capacity piles bearing in the alluvial sands and Boston blue clay, and caissons bearing on the alluvial sands and clay. Groundwater was less than one meter below the top of the CDSM wall. The new addition was founded on shallow foundations in the desiccated crust of the Boston Blue Clay. The CDSM wall was selected as the most economical means to control deep seated ground movements, limit movements of adjacent structures, and inhibit groundwater flow into the excavation. Braces and a continuous wale were used to support the CDSM wall where it was located adjacent to structures. Tiebacks were used where there were no structures. Other geotechnical construction at the site included: ? Jet grouting (JG) to improve the ground and provide an impervious subgrade layer at the west end of the addition, ? Concrete pier underpinning was used to support an existing structure on the west end of the site, and ? A secant pile wall using alternating drilled shafts and jet grout columns was used for earth support and a barrier to groundwater flow to allow for the installation of a storage tank at the south end of the site. Inclinometers, total station surveying, vibrating wire strain gauges on the braces and wales and load cells on the tiebacks were used to monitor performance of the excavation support system. The excavation support system performed better than required limiting lateral movements of the adjacent structures to less than 13 mm and vertical settlement to less than 8 mm. No settlements or movement were detected during the construction of the wall. Lateral movement of the CDSM wall was typically below 15 mm with the maximum movement occurring near subgrade.

Jan 1, 2011

By Jim Bruce

The Transformation AGO project, constructed between 2005 and 2008, featured a foundation trade contract that included design of pile caps and grade beams and construction of 138 permanent micropiles. The new foundation works were constructed within seven different settings ? each featuring a host of attributes challenging to constructability ? inside and outside the existing Art Gallery of Ontario, all while the gallery remained open for business. Transformation AGO resulted in several firsts for micropiles in the Toronto construction market: this was the first micropile trade contract with a multimillion dollar contract value; it featured the first static compressive load test performed beyond 7000 kN on a single micropile; the first static compressive load test beyond 8000 kN on an experimental pile cap supported by two test micropiles; and it was the first publicly funded project to go to tender with micropiles listed as the preferred foundation option. This paper outlines the successful application of micropiles at the landmark Transformation AGO project.

Jan 1, 2011

By S. N. Monteiro, C. M. F. Vieira, M. M. Ribeiro

"This work has as its objective to evaluate the effect of incorporation of the powder waste retained in the eletrostatic precipitator of the sintering stage from an integrated steel making plant on the physical and mechanical properties of a red ceramic. Formulations were prepared with incorporation of the waste in amounts up to 20 wt.% into a kaolinitic clay. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa and then fired at 750, 900 and 1050°C. The evaluated physical and mechanical properties were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste has a potential to be used into red ceramics. The incorporation of the waste enhanced the properties of the ceramic, decreasing the water absorption and increasing the mechanical strength at all investigated temperatures.IntroductionThe sintering stage of an integrated steel-making plant is dedicated to the agglomeration of a mixture of iron ore, coke or coal, fluxes and water [1]. It is a common practice in this stage to use of solid wastes with great amounts of iron in the form of sludge and powder. One of the atmospheric pollutants generated during the sintering process is the particulate material, which is normally retained in an equipment denote as electrostatic precipitator. This equipment retains very small particulates, present in the gaseous emissions by application of an electrical potential difference in between the plates that the fluid is forced to go through. [2]."

Jan 1, 2011

By Jürgen Antrekowitsch, Thomas Griessacher

"Heavy metal containing residues are typically hazardous wastes because on the one hand, a deposition gets more and more complicated and on the other hand, the large amounts of metals like Zn, Cu, Fe and Pb represent a significant value. Thus, a post-treatment of these materials with the recovery/recycling of the metals and stabilization of the waste is not only ecological but often also economical. The therefore typically applied recycling processes utilize pyrometallurgical steps, where carbon or carbon monoxide from fossil coal and coke is used as a reducing agent, which results in large amounts of CO2 emissions. An alternative option is the application of a hydrogen-rich gas emitted in biomass utilization processes as a carbon-neutral reducing agent. Investigations in a retort process which were done at different temperatures and times showed excellent results concerning the achievable reduction rates and final contents of the heavy metals for various residues.IntroductionNowadays heavy metal containing residues like electric arc furnace dust (EAFD), dust from cupola furnaces, waelz slag, etc. are declared as hazardous wastes in a growing number of countries due to the leachability of the heavy metals in these residues. For that reason it is no longer possible to landfill these materials or use them for road construction or disposal works. Some land filling activities, carried out until now, have only been realizable because of some process modifications or cost intensive post-treatment steps of these residues. But the disposal capacities for such materials are decreasing, therefore increasing the prices. The second point for the growing disposal limitations is the stringent environmental legislations and regulations, which restrict the number and amounts of materials which can be dumped [1 – 5].From the other point of view these heavy metal containing residues usually have high contents of zinc, lead, iron, etc., which represent a significant value and therefore a big potential to recover these metals. This is why in recent years the number of recycling processes and the amount of recycled heavy metal containing residues have continuously increased. These recycling processes have the target to recover the valuable metals from the residual materials in the form of a saleable product as well as the stabilization of the slag produced in these processes [5, 6]."

Jan 1, 2011

By Joseph Indeck, Seokbin Lim, Andrew Thompson

In the design of explosively driven penetration devices, understanding the impact conditions between the explosively propelled penetrator and the target is one of the most important steps in optimizing the performance of the device. These impact conditions are especially prevalent when a shaped charge jet impacts concrete, which is not an ideal target material. The specific impact conditions, including but not limited to the impact angle and jet properties, create a great deal of variability that affects the performance and penetration of the shaped charge. The large amount of impurities and voids in concrete, along with its heterogeneous nature and the general strength characteristics, make concrete a non-ideal material for shaped charge jet penetration. These material characteristics lead to a highly non-linear deformation behavior of the concrete target during a hyper-velocity impact.

Jan 1, 2011

By M. Abdellatif

The Mintek Thermal Magnesium Process (MTMP) process is based on DC open arc metallothermic smelting of calcined dolomite at normal pressure and temperatures of 1650?1750°C. The process was demonstrated at the pilot scale in the period 2000?2004. Major changes to the MTMP pilot plant were made throughout the development period, which lasted for about five years. The changes included design and installation of new equipment, modification of existing equipment, changes in the metallurgical approach in terms of feed rates, feed recipes, furnace operating temperatures, cold and hot dolime feeding, and steady and systematic changes in the operating procedures and maintenance of the plant. As a result, the performance of the pilot plant gradually improved from one campaign to the next, in terms of availability and in particular the condensation efficiency. In Run 10, the process was successfully demonstrated over an 8-day campaign. Keywords Magnesium, condensation efficiency, DC arc furnace, silicothermic reduction.

Jan 1, 2011

By S. Khoshjavan

Separation of refractory rock phosphate (P2O5 = 11.5%) from the Dalir area, Iran, containing quartz, calcite and other impurities, by calcination and flotation processes has been successfully used to upgrade the phosphate values. Petrographic studies of this ore showed that collophanite was the major phosphate mineral and the main gangue minerals were calcite, dolomite and quartz. The results of characterization studies showed that the liberation degree of apatite occurred below the average grain size of 140 µm. Preliminary flotation tests were used to process the phosphate samples. Results of preliminary flotation tests showed that they don?t contain any desirable efficiency (grade or recovery) of P2O5. Calcination was the best process for preconcentration of this ore. In the desliming stage, about 14.4% of total P2O5 was removed. Encouraging concentrate grades were obtained after flotation with anionic and cationic flotation, successively. The reagent schemes that have been used in this study consisted of COCO-amine acetate and fatty acid as silicate and apatite collectors, respectively, as well as fuel oil and anionic poly acryl amid as promoter collectors. The optimum pH values for direct and reverse flotations of phosphate were 11 and 6, respectively. Experiments conducted using d80=140 µm deslimed fractions has yielded an acceptable grade of more than 30% P2O5 with a recovery of more than 62%. Finally, a laboratory flowsheet for the processing of Dalir refractory phosphate ore has been proposed.

Jan 1, 2011

By Dale Dean, Bill Hancock, Raul Mondragon, Carlos Aguilar, Chris Martin

"In 1942, commercial mining operations began in what is now the Lucky Friday Ag/Pb/Zn mine in Idaho’s Silver Valley. Wholly owned since 1962 by Hecla Mining Company, the mine has produced more than 145 million ounces of silver and has been a mainstay producer in Idaho’s Silver Valley for over 70 years.However, by the early 21st century, the mill had fallen, technologically, seriously behind the rest of the industry. Accordingly, starting in 2005, the current mill management team set to revitalizing the milling operation. This paper will describe how the mill was systematically evaluated and the aging infrastructure replaced with more current technology. Driven by internal mill review studies supported by QEMSCAN mineralogical balancing, the mill has in recent years been through waves of upgrading – from the installation of new mechanical and column flotation equipment to the introduction of on-stream analysis, a technology well-accepted around most of the industry but alien to this technologically conservative mining district.The experience at Lucky Friday is a testament to the need for ongoing structured mill optimisation and technology upgrading in established mining operations. This paper will describe engineering experiences associated with upgrading equipment in an operating mill, contained in a confined building. Experiences in teaching the team new ways of operating a mill, and finally the metallurgical rewards that have been reaped will be described.INTRODUCTIONMining in Idaho’s Silver ValleyIdaho’s Silver Valley is a 64-km long valley flanked by the US Northern Rocky mountains, seldom more the 3-km wide, and stretching across much of Idaho’s northern panhandle, roughly 150 km south of the Canadian border. Mining has been continuously active in the area for more than 140 years, during which time, the Silver Valley has become one of the richest silver producing districts in the world, and as of 1985 had out-produced the 500 years of production from the famed Potosi district in Bolivia. Since 1885, almost 100 deposits have been discovered and worked in the district (Chapman, 2000)."

Jan 1, 2011

By C. Frenzel

Tunnel boring machines (TBM) utilize disc cutters as the primary means for excavating hard rock. Depending on rock excavatability and rock abrasivity disc cutters can exhibit significant wear. A detailed analysis has been carried out to characterize failure modes and wear patterns of disc cutters. The relationship between rock properties, op-eration of the TBM, and failure modes of cutting tools is clearly high-lighted. On that basis a prediction tool for disc cutter consumption has been developed that allows to estimate not only gross cutter life, but accounts for cutterhead design, premature cutter changes, and disc cutter repair costs.

Jan 1, 2011

By Wellington Pereira Inácio, Fernando Wypych, Sergio Neves Monteiro, Artur Camposo Pereira, Rafael Marangoni

"The efficiency by which an applied load is transmitted from the matrix to reinforcing fibers in a composite depends on the fiber/matrix adhesion strength. This is determined as the interfacial shear strength, IFSS, which may be measured by means of pullout tests that measure the force needed to pull a single fiber out of a block of material simulating the composite matrix. Different techniques are used to perform pullout tests. The objective of this work was to characterize the IFSS of sisal fibers embedded in epoxy matrix through the determination of the critical length pullout curves. As the main results, a relatively small critical length was found for the sisal fiber/epoxy pullout specimens, corresponding to a weaker IFSS. This was compared to other results applying different pullout techniques. Scanning electron microscopy observation identified the mechanism responsible for the weak sisal fiber adhesion to the epoxy matrix.IntroductionSynthetic fiber reinforced composites is today one of the most successful class of materials with increasing industrial applications from house appliances to large airplanes like the modem Airbus 380. However, environmental issues are revealing serious drawbacks related to the fabrication, use and post-use discard of these composites. For instance, the thermoset polymer composite reinforced with E-glass fiber, known as ""fiberglass"" has an energy-intensive fabrication associated with a surplus emission of C02, which is responsible for global warming [1]. Moreover, the glass fiber is considered toxic and also causes long term pollution after being discarded."

Jan 1, 2011

By D. D. Southworth

In 1987, the Bureau of Mines initiated a mineral assessment of the 5.7 million-acre Valdez Creek Mining District (VCMD). Following a literature search and interviews with persons knowledgeable about deposits within the district, limited on-site field visits were made to various deposits. Present within the district are the industrial minerals limestone, argillite, granite, basalt, perlite, zeolite, and sand and gravel. At least six limestone deposits of potentially economic size and grade are known to exist within the district. Adjacent to the Parks Highway and marginal to the district, a limestone deposit is currently being mined as a source of agricultural lime. A perlite occurrence near Yacko Creek was evaluated but proved not to be of industrial grade. The sand-and-gravel resources of the district are vast, but high silt content renders many of the glacial deposits unsuitable for use in construction applications.

Jan 1, 2011

By S. Frimpong

Shovel excavation constitutes a significant component of production costs in any surface mining operation. This makes shovel loading an important cost center that needs to be improved to lower production costs. Optimization of tool design will improve energy efficiency in earthmoving operations. However, modeling the soil-tool interaction is a complex process due to the fact that forces for excavating particulate material are functions of many variables. The magnitude of this resisting force depends not only on the type of soil but on the size, shape and orientation of the cutting element. Moreover, part of this complexity is attributed to the fact that the behavior of the material during excavation is not yet well understood. For the past five decades, researchers have mostly used the passive earth pressure theory to study the soil failure patterns around a cutting tool and to develop force prediction models for design optimization with some success. Although the force models developed from the passive pressure theory have been successful to some extent, they can hardly be extended to a general case because of the underlying assumptions and simplification of tool shapes. This paper aims at reviewing some of the existing empirical and analytical methods of cutting and excavation tool modeling with a focus on their merits and limitations. The paper also explores the use of numerical methods, specifically the discrete element method, for dealing with the unresolved aspects of soil dynamics in excavation.

Jan 1, 2011

By E. Asselin

Passivation of Fe-Ni-Co alloys during the Caron leach process is thought to result in low cobalt recoveries in ammoniacal ammonium carbonate solutions. A brief review of the available thermochemical data for the (Fe, Ni, Co)-NH3-H2O systems has been undertaken. The stability of the Co(II) and Co(III), Ni(II) and Fe(II) am-mines was examined through the use of speciation and Pourbaix diagrams at 298 and 333 K and at 6 M total ammonia. Increasing the temperature reduces the stability fields of the ammines and generally constrains the thermodynamic window for the leach. The Fe(II) ammines are only thermodynamically stable under reducing conditions. Polarization experiments show that these ammines are unlikely to form if oxygen is present. Fe-Ni-Co alloy passivation may be alleviated by careful management of potential.

Jan 1, 2011

By Yuanbo Zhang, Guanghui Li, Zhenyu Fan, Tao Jiang, Xiaohui Fan

"Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60% of the total. Aiming at the features of sintering flue gases and existing problems during the flue gas desulphurization, a technical route of flue gas circulation sintering (FGCS) for iron ores has been put forward. Under the simulated experimental conditions, effects of FGCS process on the main output and quality indexes and SO2 emission rule are researched using simulating flue gases. Compared the novel FGCS with conventional sintering process, SO2 in the final sintering flue gas is obviously enriched and the total exhaust gases can be reduced evidently. The decreasing of oxygen content in circulating gases has bad effect on the sintering indexes. Increasing the oxygen potential is beneficial to obtain high quality sinters. This investigation shows that the FGCS process is promising.IntroductionSteel is a kind of essential material for modern society, but steel-making process is characterized by high energy-consumption and emission as well as heavy environmental pollution. Chinese steel industry has developed rapidly in the last decade, and the environmental problem caused by ironmaking and steelmaking have also aroused the greatest concern, especially the atmospheric pollution caused by SO2, CO2, etc. Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60 % of the total. The development of the desulfurization process for sintering flue gases to reduce SO2 emission in sintering process is not only the requirements of sustainable development but also the most important environmental tasks for steel industry [1-5]."

Jan 1, 2011

By Ajoy K. Singh, B Mohanty, P K. Singh

A study was conducted to investigate the damage potential to underground multiseam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with much higher amplitudes compared to those in pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or higher. The vibration magnitude recorded was higher in upper-seam openings than in belowseam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle velocity-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for the safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.

Jan 1, 2011

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011

By J. M. Garcia

This paper highlights several management practices from the oil and gas industry to support the proposition that financial performance in the finite, non-renewable resource business relates more to upstream rather than downstream activities. Based on the analysis of nine oil and gas companies, this study supports a previous study involving fourteen mining companies that showed reserves growth is one of the main levers of value creation in mining. Interestingly, this study also finds that the oil and gas industry has been historically more profitable than mining. The reason, it is argued, is that oil and gas companies count on management practices that focus primarily on the upstream segments of the business, compared to the traditional downstream focus of mining. This paper delves into these ideas to conclude that what mining may need to improve its competitive advantage is a new organizational framework. Another conclusion is that the upstream management focus is vital not only for strategy formulation in the resource business, but also for policy formulation in economies based on the export of finite, non-renewable resources.

Jan 1, 2011