Search Documents

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By H. J. McQueen

Before 1950, hot working was simply deforming above the recrystallization point and gave a soft product compared to cold working. From 1960 onwards, improved testing in compression and torsion (stress, strain rate, temperature, quenching) provided valid specimens for microstructural analysis by polarized optical and transmission electron microscopy (TEM). Indeed, TEM was essential to uncovering the hot working mechanisms because it could distinguish between cold and hot substructures (dynamic recovery) in either initial or new grains (dynamic recrystallization). Over the years, teams at Concordia, McGill and UBC obtained NSERC support for students and equipment. CANMET built up a hot forming group having capabilities from high-rate cam-plastometer compression to rolling of experimental alloy billets; this was combined with latest metallographic instruments for fundamental research. Al alloys of every class (2000, 3000, 5000, 7000, 8000) were studied to understand the effects of solutes, precipitates, dispersoids and composites. The complex flow patterns in extrusion were clarified and modeled by finite element methods. Physical simulations of rolling schedules (up to 20 passes and reductions of 98%) by torsion provided evidence of microstructure development during both the passes and the softening intervals, thus clarifying development of texture in different alloys. The results frequently appeared in proceedings of Light Metals symposia and Canadian Metallurgical Quarterly

Jan 1, 2011

By L. Bergkvist

"History can provide many answers with regard to what today’s mining industry looks like and how we got to where we are today. It has always been self-evident that safety has to be given the highest priority and, throughout history, many mine workers have been injured, become ill and have even sacrificed their lives due to the way in which attempts have been made to extract the ore, often due to ignorance of the dangers being faced. In more recent stages of history we have seen certain dangers being compensated by means of higher wages and bonus systems in order to have the work carried out: one example of this is when the rock heating method was employed and the men who first went underground to put out the fires that were burning, were paid extra. The working conditions, to which these people were exposed, with smoke-filled closed spaces, shortened their life expectancy considerably and today we can ask ourselves whether it is really possible to value these efforts just by higher wages. In all mines worldwide the working environment has been improved and many mining companies have a zero vision where work-related injuries and accidents are concerned. Despite this, incidents of varying severity still occur and a continuous improvement process and ongoing training is necessary in order to constantly minimise risks and improve the working environment. Atlas Copco takes this into account in all its development and we not only review our own production units but also the needs of our customers, with regard to the machinery that is produced in order to cater for customers’ safety and production objectives. Underground mining probably started at the beginning of the 11th century when people with modest tools tried to extract ores that were present in the bedrock. Methodology has developed enormously over the years with a strong focus on increased efficiency and higher production. In different parts of the world the development is driven forwards at different rates depending on which controlling factors are regarded as necessary. Political decisions, profit goals and productivity have partly controlled the development, but the greatest factor where improvement is concerned still remains with increased understanding of the totality. During more than 1000 years since underground mining has been conducted, all individuals at all levels have constantly improved their expertise and the human element has been of great importance with regard to the development that has been made, even though technology often occupies a leading role when we describe the improvements made."

Jan 1, 2011

By Jan E. Nesset, James A. Finch, Frank Rosenblum, Rebecca Payant

"Under certain conditions of moisture and oxygen, sulphides can spontaneously heat, a phenomenon known as self-heating. In this paper, we test a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by restpotential difference between minerals and their surface area of contact (particle size). In order to decrease rest-potential, four sulphides were tested: pyrite, chalcopyrite, sphalerite and galena. Two series of samples consisting of mixtures of two sulphides, each representing a mass fraction of 50 %, were run in standard self-heating tests. The first series comprised five mixtures, two with low rest-potential difference (pyrite-chalcopyrite and chalcopyrite-sphalerite) and three with high rest-potential difference (pyrite-galena, chalcopyrite-galena and pyrite-sphalerite). The second series was performed on a pyrite-sphalerite mixture at four particle sizes (80 % passing 850 µm, 300 µm, 75 µm and 38 µm). The first series showed that the individual sulphides and the mixtures of low rest-potential difference did not self-heat but the mixtures of high rest-potential difference did self-heat. The second series showed that self-heating increased inversely with particle size (increased specific surface area) and revealed that it was the fineness of the pyrite (high rest-potential sulphide) that governed the self-heating effect, indicating the rate-limiting step is the reduction reaction on pyrite (cathodic mineral). The increase in self-heating with high rest-potential difference and increasing particle fineness supports the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on the hydrogen sulphide hypothesis is proposed where the reduction reaction at the cathodic mineral surface is ferric to ferrous. The understanding gained will be of interest to those involved in storage, shipping and disposal of sulphide minerals.INTRODUCTIONSulphide mineral ores are the major source of most base metals such as copper, zinc, nickel and lead. Once the ore is extracted, the sulphide minerals are liberated by size reduction (crushing and grinding), concentrated by flotation, and the concentrates sent for further processing to extract the metal (smelting and refining). At the various stages from mining to concentrate shipment and tailings storage, the sulphides are exposed to a variety of environments, which under certain conditions of air (oxygen), humidity and temperature can cause them to heat. Since no external heat source is involved, this pyrophoric process is known as spontaneous heating or, more commonly, self-heating. The self-heating of sulphides is associated with oxidation reactions under moist conditions. If the heat generated is greater than the heat dissipated, the sulphides will self-heat and the material temperature will rise. This can make working conditions potentially dangerous as oxygen is consumed from the surrounding air and significant quantities of sulphur dioxide (SO2) can be released (Ninteman, 1978)."

Jan 1, 2011

By F. Carew

Accurate knowledge of what mass and grade is to hand and where it is stored is key to mine efficiencies and overall profitability. In order to make the right decisions and align production with stockpile capacity, feed and contract demand, a clear and accurate view from production through blending and processing is required. The use of a mine production management solution can provide you with a high degree of confidence in and visibility into validated data as well as auditable and traceable material movements, activities and surveys. A robust calculation engine enables mass and grade changes to propagate to material movements and stockpiles to ensure you are getting the most accurate view at all times. Tracked changes in material balances can be readily incorporated in revised production schedules to close the loop. The availability of accurate, timely information, coupled with predictive trend indicators, is a significant advance in narrowing the gap between claimed and planned production that is common to many mines, regardless of commodity. This paper provides an overview of a Mine Production Management System (MPMS) and explains how the system helps address the challenges listed above.

Jan 1, 2011

By Boyd Davis, Vladimiros Papangelakis, Joshua LaMarre, Jan de Bakker

"HCl leaching using molten salt hydrates has the potential to improve the extraction of nickel from laterite ores. However, as in other HCl leaching applications, recovery of HCl is key to process economics. Spray pyrohydrolysis, which is used in current chloride-based flowsheets, is associated with a high energy cost. The authors have developed a proposed laterite leach circuit using an alternative HCl recovery route. The leach circuit envisions a leach by concentrated (33%) HCl in an MgCl2 molten salt hydrate (MSH) or brine medium, followed by Ni/Co recovery and iron precipitation. Magnesium and chloride are precipitated from solution as magnesium hydroxychloride; this hydroxychloride is thermally decomposed to produce HCl gas. The proposed flowsheet employs a chloride leach circuit with simpler equipment and lower energy cost than in the conventional practice of pyrohydrolysis. Laboratory work investigated key aspects of the flowsheet, including precipitation of magnesium hydroxychlorides and their composition; magnesium hydroxychloride thermal decomposition; and iron control.Introduction As sulphide nickel ores become harder to mine and more complex to process, laterite ores will increase in importance. Laterite ore deposits can be divided into two main mineralogies. Limonite ores consist mostly of hydrated iron oxide, FeOOH, with 1-3% nickel substituting for the iron. Saprolite ores consist of iron-magnesium silicates, (Fe, Mg)2Si04, again with some nickel substituting for the metal ions. Limonite ores can be treated using the HP AL (High Pressure Acid Leach) process, in which the ore is reacted with sulphuric acid at high temperature in an autoclave. HP AL, however, cannot in general be used to treat saprolite ores because the magnesium enters solution and consumes sulphuric acid, which results in excessive spending on lixiviant. It is therefore desirable to find a hydrometallurgical process specifically for saprolite ores that can provide better results than the treatment options currently available."

Jan 1, 2011

Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to the company's industry peers in the platinum group metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that resulted from milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tapblock movement, the formation of three-phase 'mushy' zones, high refractory and taphole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to redesign Furnace No. 1, to invest in backup furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line monitoring of feed chemistry and mineralogy, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilizing optical spectral analysis of the converter flame to characterize converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

By B. Zeifert, C. Martínez-Morales, A. Romero-Serrano, A. Pineda-Rivera, H. Martínez-Gutiérrez, G. Diaz-Sandi

In this work, the effects of CaO/SiO2 ratio and the FeSO4 and FeS2 contents on the stability of the mineralogical species in chromium-based slags were studied. The chemical stability was evaluated by leaching with an acid solution. The main Cr-compounds in slags with FeSO4 and CaO/SiO2=1 were FeCr2O4 and Ca3Cr2Si3O12, while Cr3S4 predominated in slags with FeS2. The slags with CaO/SiO2=2 mainly contained CaCr2O4. The highest Cr concentration levels in the leaching liquors corresponded to slags with CaO/SiO2= 2, and the lowest Cr concentration corresponded to slags with high FeSO4 or FeS2, owing to the stable binding of chromium in the compounds FeCr2O4, Cr3S4 and FeS•Cr2O3.

Jan 1, 2011

By B. Oraee

Accurate estimation of equipment costs is a key factor in feasibility study and evaluation of design alternatives of mining projects. In this paper, capital and operation costs of backhoe loaders are estimated using multiple linear regression (MLR), based on principle component analysis (PCA). These cost functions are consisted of five independent variables; bucket size, digging depth, dump height, weight and horse power. The MLR is conducted in two steps. At the first correlation between independent variables is omitted using PCA technique. Thereafter, MLR functions are established using selected significant PCs and total cost functions are constituted as functions of initial variables. At the end, accuracy of functions are evaluated using mean absolute error rate method.

Jan 1, 2011

By Hongbo Zhu, Jinhui Peng, Linqing Dai

"To optimize the process variables for making direct reduced iron (DRI) by microwave heating, the reduction temperature, reduction time and the ratio of coal to material were studied with the central composite design (CCD) and their interactions on the Metallization rate were also investigated. The predictive polynomial quadratic equations model was analyzed by ANOVA. Optimal conditions of making DRI can be concluded as follows: 28 min at 1139?, the ratio of coal to material is 20.95%. Under these conditions, the metallization rate is up to 97.06%.1. IntroductionThere are some technical problems in making direct reduced iron (DRI) or sponge iron using iron ore concentrates containing coal and lime. In reduction of the iron ore concentrates containing coal with microwave heating, the strength of pellets needn’t to be considered. It reduces the costs and improve quality of materials, but also eliminates the need for pellet preparation process, simplifying the process and achieving a cleaner production.Microwave energy is a clean energy, and has characteristic of selective heating. The speed of heating is also fast. It researched by Chen Jin that when the mole mass of C: O is 0.627 and the microwave power is 15KW, it only spends 15min from 15? to 1021.6? with 1 kg iron ore containing coal with microwave heating [1]. There are many factors affecting metallization rate. In order to find a suitable condition for reduction process, it is necessary to design a series of suitable experiments.Response surface methodology (RSM) is one of the relevant multivariate techniques which can deal with multivariant experimental design strategy, statistical modeling and process optimization [2–5]. It is used to examine the relationship between one or more response variables and a set of quantitative experimental variables or factors. This method is often employed after the identification of the vital controllable factors to find the factor settings that optimize the response. Designs of this type are usually chosen when a curvature in the response surface is suspected. The process optimization of the microwave reduced iron ore was seldom reported in literature. Hence the present work intends to assess the effects of variables such as reduction time, reduction temperature and the ratio of coal to identify the optimum conditions using a central composite design (CCD). The characteristic of product was assessed using scanning electron microscope (SEM)."

Jan 1, 2011

By E. L. Thyse

Keywords: Pyrometallurgy, converter, nickel, matte, distribution Metallic elements occupy a wide range in granulated nickel converter matte phases. The distribution of these metallic elements, particularly during crystallization path events, appears to be poorly understood. The present study serves to investigate the distribution of Fe, Co, Ni, Cu, and Pb between nickel-sulphide, copper-sulphide, and alloy phases. A novel combination of thermo-chemical modelling, electron microscopy, and electron probe microanalysis was applied to understand crystallization path events and the associated metallic element distribution. This study has demonstrated that major Ni incorporated during copper-sulphide crystallization would serve to mobilize minor Co towards distribution in copper-sulphide phases. In addition, solid solution substitution of Cu by Ni is manifested by compositional zoning of copper-sulphide phases. The role played by Ni during alloy crystallization suggests that minor Co was also mobilized, along with an increase in principal Ni. Fe, by contrast, seems to be incompatible with principal Ni. In addition, solid solution substitution of Ni with PGEs and Cu is manifested by compositional zoning of NiCu-alloy phases.

Jan 1, 2011

By U. Thorley

Management of mine and tailings reclamation activities by surface mining oil sands operations in Alberta, Canada is experiencing increased national and international attention. Of particular concern is the ability of existing mines to execute and fund reclamation activities. Concern stems from a lack of demonstrated tailings reclamation technologies, perceptions of a poor track-record of reclamation activity by industry, and a lack of transparency with respect to the potential cost of reclamation activities relative to the monies secured in Alberta?s Environmental Protection Security Fund (EPSF). Limited information is publicly available regarding reclamation costs and technologies. Available data typically comes from disparate sources. This paper examines the expected costs of oil sands reclamation activities through a study of corporate Asset Retirement Obligation (ARO) liabilities, the Province of Alberta?sEPSF, and published data relating to reclamation costs.Issues relating to current liability funding are introduced.

Jan 1, 2011

By R. L. Wiegel

Some of the mineral deposits that are being processed today, and especially those expected to be processed in the future, have relatively low compositions of the valuable mineral. With these low-grade ores, it is necessary to be able to design processes that are sufficiently low-cost to permit exploitation. One approach to minimizing the capital and operating costs for these processes is to use the capabilities of computer process simulation in the design phase of development, to make important technical and economic decisions regarding the evaluation of alternative process flow schemes, the selection of equipment and the choice of operating conditions. There are mathematical simulation models for most mineral processing operations, including several each for size reduction, size classification and mineral separations. To be able to tie these individual operating models together in an integrated mineral process simulation, however, it is important, in fact in some cases essential, that there be a model which describes how the mineral system responds to size reduction in making the liberated valuable and waste mineral particles available for concentration or rejection operations and the locked particles available for possible recirculation. This, then, is the role played by the mineral liberation model, showing the relationship between particle size, quantity and composition throughout the process.

Jan 1, 2011

By D. Mkhwanazi

The purpose of the project was to optimize load haul dump (LHD) machinery use as they were spending too much time doing what they should not be doing. During the investigation, the author found that the machine's actual availability was 86% and the utilization ranged between 30% and 42%. This shows that the availability of the machine has met its target. Therefore the main problem was with the LHD utilization and that is what the project focuses on. To satisfy the objectives, the author firstly studied the existing mining data like the key performance indicators (KPIs) in order to analyse the machine's availability and utilization; this is what gave direction to the problem. Secondly the author did a literature review on mines with similar problems. This gave the author ideas on what to look at in approaching such a situation. Thirdly, the author gathered information on what the LHDs are doing on a daily basis by doing a time study. This gave the author an idea of how long it took the LHDs to complete a specific task. The author also interviewed operators and their supervisors in order to find the best practice work. This helped in identifying the problem areas when comparing the best practice work with what the LHDs are actually doing. According to the project results, it was found that the LHDs are underutilized due to shortage of drivers and the long distances the LHDs have to travel for material loading and refuelling. The author recommended that the machine utilization should be improved by training more operators in order to eliminate the 'no operator' downtime; the cost arrangement of this recommendation is included in the report. The author also recommended that the travelling time should be reduced by using tractors instead of LHDs when long distances need to be travelled for material loading. Another recommendation for reducing travelling time was to bring the mobile fuel tank closer to a section; the cost arrangement for this recommendation is also included in the report. Keywords Optimizing, LHD utilization, LHD availability, key performance indicators (KPI), shortage of drivers, long distances, mobile fuel tanks.

Jan 1, 2011

By Alwin Frei, Aldo Steinfeld, Peter G. Loutzenhiser, Enrico Guglielmini

"Using concentrated solar radiation as the energy source of high-temperature process heat, the carbothermal reductions of Al2O3 to Al and SiO2 to Si were examined thermodynamically and demonstrated experimentally at vacuum pressures. Reducing the system pressure favors Al(g) and Si(g) formation, enabling their vacuum distillation and avoiding contamination by carbides and/or oxycarbides. Exploratory experimentation in a solar reactor was performed with mixtures of charcoal with alumina and silica in the ranges of 1300-2000 K and 1997–2263 K, respectively, at 10-3 bar by direct exposure to concentrated thermal radiation. Distilled samples contained up to 19 wt% of Al in Al-Al2O3 mixtures and 79 wt% of Si in Si-SiO2 mixtures. When the reducing agent is derived from a biomass source, the solar-driven carbothermal processes are CO2 neutral.IntroductionMetallurgical extractive processes for producing Al1-2 from Al2O3 and Si3-6 from SiO2 are characterized by their high specific energy consumption and concomitant emissions. Alternatively, concentrated solar energy can be used as a high-temperature heat source to drive the carbothermal reductions and, thus, avoid greenhouse gas emissions and other pollutants derived from fossil-fuel-based processes7-12. When the reducing agent is biomass charcoal, the solar-driven carbothermal reduction is CO2 neutral. The carbothermal reductions of Al2O3 and SiO2 are represented by the simplified overall stoichiometric reactions:"

Jan 1, 2011

By A. J. Vietti

A pilot plant paste thickening campaign was conducted at the Anglo Platinum Limited Mogalakwena South Concentrator plant in South Africa in order to determine the water saving capability of P&TT technology. In the process a simple water consumption model was developed for estimating the overall water consumption of the mine. The model indicates that for the Mogalakwena tailings, significant water savings are achieved by discharging thickened tailing directly to the TSF but only at densities where free water release at the TSF is close to zero. Keywords Paste, thickened tailings, thickener, water savings, water consumption.

Jan 1, 2011

By F. T. Cawood

The new mineral royalty regime for South Africa was signed into law in November 2008, with its main objective being to compensate the State for the depletion of public minerals through a royalty charge payable from 1 March 2010. The aims of this paper are to establish the potential impact of mining royalties on State revenues, industry affordability, and explore whether the dual formula system is likely to encourage miners to become refiners. It also measures the royalty dispensation against economists? tax standards in an attempt to make a judgement on the ?equity? of the new system. This paper argues that most stakeholders should be comfortable with most of the requirements of the Act for most of the time. However, the new regime is unlikely to motivate miners to become refiners, as the benefit of the reduced rate on refined minerals appears to be insufficient to justify the additional costs to refine the mineral resource to the prescribed states of beneficiation.

Jan 1, 2011

By Steven A. Fechner

In 1984 the Bureau of Mines cunducted mineral investigations of specific sites within the Yentna Mining District. One hundred eight placer and rock samples were taken. Reconnaissance placer samples were collected from drainages in the Talkeetna, Susitna, and Yentna River basins. The highest placer gold values were found in the historic placer gold producing creeks of the Cache-Peters Creek area. Samples taken from an outcrop in the Middle Fork of Iron Creek in the Talkeetna Mountains contained previously unreported high lead, zinc, and silver values.

Jan 1, 2011

By Eleazar Salinas R., Miguel Perez L., J. Cesar Juarez T., Martin Reyes P., Eduardo Cerecedo S., Isauro Rivera L., Francisco Patino C., Juan Hernández A.

"A complete characterization of burrows from Mining district of Pachuca - Real del Monte, in Hidalgo state Mexico, was done. These kind of residues had not been formally characterized, founding an average chemical composition of 70.43 % wt. of Si02, 7.032 % wt. of Ah03, 2.69 % wt. of Fe20 3, 0.70 % wt. of Mn, 3.98 % wt. ofK20, 3.34 % wt. of CaO, 2.50 % wt. ofNa20, 1.01 % wt. of MgO, 0.26 % wt. of Ti02, 0.04 % wt. of Zn, 0.026 % wt. of Pb, 56 g/ton of Ag and 0.6 g/ton of Au; In the same way, the residues present as majority mineralogical phases the following: Quartz, Berlinite, Orthoclase, Feldspar, Anorthoclase and Calcite. By the other hand, joint with the big volume that present these residues and the chemical and mineralogical characteristics, these materials or sub - products can be used for production of ceramics, into mixes forming some materials for architecture (bricks, blocks, and tiles), refractory bricks, in the production of cement and to get some metallic values such as gold and silver involved in these residues.IntroductionActually the mining residues in Hidalgo State, Mexico are the result of more tan 500 years of mining, leading so a great volume of deposits, which we can classify in different types, among the most communes we have: Acid Mining Waters, Waters of solid transport and elements in the form of radicals, deposits of abandoned minerals without processing, and mining wastes of processed minerals known as burrows or dumps, being these the most abundant in the Hidalgo State [1-4].Form the metallurgical point of view, it is known that a characterization study if fundamental to find the viability of reuse of these kind of residues, leading so an additional use and the opportunity of get an alternative use into several industrial processes, due to its contents of oxides of silicon, iron, aluminum, calcium, sodium and potassium, principally, besides of its mineralogy and distribution of chemical elements into its primary and secondary phases [ 1-2, 5- 6]."

Jan 1, 2011

By Kenneth G. Thomas

Since approximately 2003 we have witnessed the unprecedented escalation in commodity prices. Coupled with economic chaos following the 2008 economic downturn this has caused difficulties in controlling schedule, capital costs and operating costs for mining projects. Once again escalation has returned to commodity prices fuelled by growth in the BRIC countries especially China and Brazil. This is further exasperated by the missing generation of skilled technical personnel not graduating from universities in the 1980s and 1990s owing to depressed commodity prices. This paper examines the six tenets for successful project implementation.

Jan 1, 2011