Search Documents

By R. Khanna, K. Hyun Ko, A. J. Berkovich, J. Hook

"The co-pyrolysis of synthetic polymer polyethylene terephthalate (PET) and agricultural wastes (naturally occurring polymer-macadamia nut shell) was investigated in the temperature range 473K to 1273K using a horizontal furnace with an aim to understand their thermal degradation under isothermal conditions. In-depth characterization of pyrolysis residues was carried out using x-ray diffraction (XRD) and solid state nuclear magnetic resonance (NMR) for carbon structure, and through determination of the concentration of unpaired electrons using electron paramagnetic resonance (EPR). In previous studies, it has been found that PET thermally decomposes ~ 650K-700K, releasing (~80 wt % of initial weight) gaseous products due to random chain scission. In the case of macadamia nut shell, three types of byproduct can be obtained from pyrolysis: char, tar and gaseous products. In the co-pyrolysis of macadamia nut shell with PET in 50-50 wt% ratio, total product weight ratio could be modified with the addition of PET acting as a hydrogen source. This is because a recombination of thermal cracking products of cellulose could be suppressed by hydrogen from PET, which will later lead to an enhancement of tar formation. In addition, pyrolysis around 673K is sufficient for bond cleavage to occur in cellulose and lignin leading to the formation of negatively charged activated carbon with high surface area, providing bonding sites for volatiles evolving from PET. Therefore the co-pyrolysis may be able to enhance the product yield (tar/char/solid carbon residue) along with a reduction in the release of gaseous products. During the co-pyrolysis, temperature was found to have a significant influence on the kinetics of thermal degradation and solid residual by-products after co-pyrolysis.INTRODUCTIONPlastics are being used worldwide in a wide range of applications in the modern society; their usage has resulted in increasingly a massive waste problem. The production of most synthetic plastics requires hydrocarbons that are produced from petrochemicals derived from fossil oil and natural gas, a non-renewable source (Speight 2011). Currently, plastic manufacture utilizes ~4% of world oil and gas production, and it is expected to drive further increases in petroleum demand by 1-2% due to their large volume of manufacture (Hopewell, Dvorak et al. 2009). Landfilling and incineration of plastic waste are the two main routes to plastic waste management (Encinar and González 2008). In Australia, only 10% of waste plastics were recycled in 2006 (White and Hyde 2011). This means that large amount of fossil fuels from plastics has either been simply burned for energy recovery or buried in the ground. There is an urgent need for developing alternative avenues for recycling waste plastics. Our group at UNSW has carried out extensive research on the recycling of waste polymers as carbon resource in steelmaking including slag foaming and carbon dissolution from waste plastics into liquid steel at 1600°C; the effect of basic plastic characteristics such as chemical composition, structure, bonding network etc. was examined (Sahajwalla, Rahman et al. 2009)"

Jan 1, 2012

By T. Wang

A new generated NaNO3 ? NaNO2 ? KNO3 ternary thermal energy storage system which has low melting point as 124°C and high specific heat capacity was studied for the short and long?term thermal stability by using the Thermogravimetric Analyzer (TGA). Based on the actual working condition of molten salt in solar two, the simulated cyclic thermal stability measurement was also conducted. The ternary system demonstrates excellent short ? term thermal stability and thermal reliability after cyclic heating and cooling processes. However, in the long ? term as well as the simulated cyclic stability measurement, large amount of weight loss was observed. Moreover, the stepwise long ? term isothermal study reveals that below 440°C the weight change is minimal and this temperature is viewed as the upper limit temperature of thermal stability for this ternary system. To determine the lost phases at high temperature above the upper thermal stability limit, techniques such as XRD and SEM are used to compare the condition of the salt mixture before and after the long ? term thermal stability study. On the basis of the comparison, it can be concluded that the major weight loss was due to the decomposition of sodium nitrite.

Jan 1, 2012

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert systems designed for real-time processing plants that also include the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. [1,2] In spite of the fact that significant performance increases have been achieved using these systems they are not perfect and can be improved. They suffer from the static nature of their rules and to a degree the process models. There is an opportunity to further increase system performance by systematically taking advantage of the tremendous amount of data produced by the expert system to improve the design, the heuristic rules, the model topologies and the use of the models. Data mining refers to extracting or mining knowledge from large amounts of data where the objective is to automatically analyze, classify and summarize the data to automatically discover and characterize trends in it and to automatically flag anomalies. [3] Clearly, modern process control systems are capable of collecting vast amounts of data. Without a doubt, these data contain important information on the operation of our plants and their ultimate optimization. Coupling the information mined from these data with Expert Control Systems should produce more effective control and greater knowledge of the grinding process and the flotation process. Now, with the advent of effective monitoring of entire minerals plant electric consumption it is possible to not only optimize plant production in real-time it is possible to analyze total plant electrical consumption and incorporate it into the plant control logic thereby improving the overall plant economic performance. This is particularly important with the ever more complex power contracts that plants operate under.

Jan 1, 2012

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By Cosmin Carpinisan, Erich J. Hofmann, Stephen J. Hall

"Since presenting a technical paper regarding their unique capabilities in Forged Steel Mill Gearing at the SAG-2006 Conference, Australian heavy engineering company Hofmann Engineering has pioneered a number of new manufacturing processes and design concepts for components of large comminution equipment. These include: 1. Novel design improvements for HPGR Rolls with forged steel tyres and a unique patented tungsten carbide insert designed to improve wear life, enhance autogenous layer build-up, and to reduce breakage & chipping under load. 2. Development of forged fabricated Mill Heads using rolled & welded high-tensile steel plate as alternatives to cast conical mill heads. 3. Insitu Girth Gear measurements for profile and wear via portable 6-axis CMM. 4. Gear and Pinion designs to AGMA-6114 for SAG mills of 38’-40’ diameter to 24MW and for Ball Mills of 26’ diameter to 18MW. The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering, combined with news of their new gear manufacturing and gearbox overhaul facility in Canada."

Jan 1, 2012

By Michael Rehbock-Sander

The Gotthard Base Tunnel (GBT) is 57 km (35 miles) long and consists of two par-allel single-track tubes with an ex-cavation diameter ranging from 8.8 to 9.5 m (28.8 to 31.2 ft). These are interlinked by cross-passages every 312 m (1,000 ft). Two multifunction stations (MFS) are located in the sections Sedrun and Faido, at one-third and two-thirds of the entire tunnel length (Fig. 1). These will be used for the diversion of trains to the other main tube via tunnel crossovers, for the housing of tech-nical infrastructure and equipment and for potential emergency stops. To reduce construction time, the GBT was divided into five sections and was excavated from several sites simultaneously. The tunnel was excavated from the two portals, Erstfeld in the north and Bodio in the south, and also from three intermediate attacks, with their corresponding access tunnels, in Amsteg and Faido and two vertical 800-m (2,624-ft) deep shafts in Sedrun.

Jan 1, 2012

By G. Fuentes, J. Viñals

"The nature and basic kinetics of the hydrothermal reactions of bornite, covellite pyrite and enargite with copper sulfate solutions were investigated, as a previous study on the behavior of the bulk Chilean copper concentrates. The reaction of bornite produced digenite at 160 °C and djurleite above this temperature. Covellite was transformed to digenite at < 200 °C and to chalcocite (Q and M) at > 200 °C. The pyrite reaction was significant at > 200 °C and extensive at 240 °C, enargite reacts only above 240°C and produces digenite. The hydrothermal treatment of Chilean Codelco-type copper concentrates with hydrothermal reactions was similar to those obtained from pure mineral samples.INTRODUCTIONStudies on the hydrothermal enrichment of chalcopyrite concentrates were begun by MacGauley and Roberts (1951), Roberts et al. (1953) and MacGauley and Schaufelberger (1956). In the 1970's these processes were reexamined by McKay et al. (1972), and Johnson and Coltrinari (1976), but it not was until the 1990s when the kinetics, mechanisms and full engineering aspects were studied by Barlett, (1992), Jang and Wadsworth, (1994) and Peterson and Wadsworth (1994). The main objectives were to solve some important problems in the copper pyrometallurgy: The increase of the smelting capacity, the reduction of the iron slag – and associated copper losses – as well as the reduction of sulfur emissions. The present rise in copper demand and price implies the production and subsequent treatment of very impure concentrates. Thus, a significant increase of environmental problems can be expected in the copper pyrometallurgy. The previous purification of concentrates can reduce the processing of wastes containing hazardous heavy metals in the copper refineries and the hydrothermal treatment can be an alternative which combines both enrichment and purification. On the other hand, Chuquicamatatype concentrates (Viñals et al., 2004a) contains digenite (Cu1.8S), pyrite (FeS2), chalcopyrite(CuFeS2), b ornite (Cu5FeS4), covellite (CuS) and sphalerite (ZnS) as the main mineral components, with minor amounts of enargite (Cu3AsS4), galena (PbS) and molybdenite (MoS2)."

Jan 1, 2012

By J. Dong

"A “green” collector project has been initiated at Vale Base Metals Technology Development to replace xanthate. Bench and miniplant testwork showed comparable metallurgical results between xanthate and DTC (sodium dibutyl dithiocarbamate), a “greener” collector. During the first DTC plant trial, a strong interaction between the process water and DTC negatively impacted the metallurgy. The subsequent investigation showed that the quality of process water including suspended solids and dissolved metal ions had a significant impact on the performance with DTC, while less so with PAX. This paper explains these differences using UV spectrophotometry and batch flotation tests. INTRODUCTIONVale Base Metals is dedicated to sustainable mining and mineral processing. One of the key activities is to find a “greener” collector to replace xanthate (PAX: potassium amyl xanthate), which decomposes during storage and flotation causing CS2 emissions in the work place. As the most promising candidate, DTC (sodium dibutyl dithiocarbamate) was evaluated in the lab and miniplant (Dong & Xu, 2011). Consequently, a plant trial was conducted in the winter of 2010. However, the results were not as good as expected. The subsequent investigation showed that the quality of process water played a significant role in the metallurgical performance with DTC but less so with xanthate.From test work in 1996 and 1997, a series of batch tests were performed at Clarabelle Mill to investigate the winter/summer metallurgical shift with xanthate. As shown in Figure 1, the winter metallurgy was considerably worse than the summer metallurgy (Xu & Wilson, 2000). At 80% pentlandite recovery, the concentrate (Cu+Ni) grade was 21% in the winter and 26% in the summer. At 23% (Cu+Ni) concentrate grade, pentlandite recovery was 85% in the summer and 70% in the winter. In the summer, the process water is much cleaner, with very low concentrations of dissolved metals ions and suspended solids; while in the winter, the water is yellow and cloudy, with much higher suspended solids. Based on these results, it was concluded that the process water in winter has a detrimental impact on metallurgy."

Jan 1, 2012

By D. W. Bennett, J. B. Hadaway

The operation at Phu Kham commenced design and construction in early 2006 and was commissioned in May 2008. This paper will examine and discuss the project from the inception of flow sheet development and equipment selection, equipment design and manufacture, construction, commissioning and ramp up to full production. The paper will touch on the strategies employed to achieve a short schedule and the efficient use of capital, but with the main emphasis on the grinding circuit. Various challenges during the early years of operation will be discussed including the effect of ore characteristics, including competency, on the performance of the grinding circuit. Actions to overcome these challenges and to enhance performance will also be discussed. Finally, current and future plans to improve the performance of the grinding circuit and the overall plant will be summarised.

Jan 1, 2012

By G. Belzil, F. Robichaud, M. Fullam

"The Goldex mining and milling complex is operated by Agnico-Eagle Mines Ltd. and is located in the Abitibi greenstone belt of Northwest Quebec, Canada. The mill operates presently at a throughput of 8,250 tpd with gold grade varying between 1.8 and 2.2 g/t. The ore is very high in gravity recoverable gold (GRG) at about 92% and as such a significant emphasis was placed on the gravity circuit. Commercial production started in 2008. Average gold recovery is 93.5% with about 68% of gold recovery coming from the gravity circuit. Over the course of the first several years of production, several gravity audits were carried out. In 2009, a complete gravity audit was completed, including ore, classification, Knelson Concentrators, and the gold room. In 2011, an audit was undertaken of the flotation circuit to determine the efficiency by which GRG is floated. Large samples of flotation feed and tails were collected and process for GRG content. This allowed a link between gravity and overall recovery to be made. This paper presents results of the audits and the development of a model linking gravity and overall gold"

Jan 1, 2012

By F. M. L. Mulaudzi

Metal dusting is a corrosion phenomenon that occurs in strongly carburizing gas atmospheres at elevated temperatures. Reaction kinetics and product characterizations of Alloys 602CA and 800 were examined by scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) and X-ray diffraction (XRD).The results showed that Alloy 602CA is more resistant to metal dusting than Alloy 800. Visual examination and SEM surface analysis showed that Alloy 800 suffered metal dusting attack after a relatively short exposure period. The amount of coke deposits increased on Alloy 800 with increased exposure from 96 to 336 hours. X-ray diffraction on the reacted surfaces identified graphite and austenite in both alloys and some iron oxides/spinel for Alloy 800.

Jan 1, 2012

By S. Esfahani, M. Barati, Y. Kauwachi

"Heat recovery from slag has gained attention due to its high potential in lowering energy intensity of metal extraction processes. A direct method to recover the thermal energy of slag is to use countercurrent air flow that extracts the heat from falling droplets. Often, the solidified slag is aimed to be used as a substitute for Portland cement, thus high cooling rates are required to form an amorphous slag with sufficiently strong hydaulicity. Rapid cooling however involves using large gas flow rates that in turn lower the thermal efficiency of the process. This article presents a mathematical model that was developed to determine the optimum conditions in the heat recovery process and to investigate the effect of the air flow and granule diameter on the cooling rate of the droplets as well as the thermal efficiency of the heat recovery system. INTRODUCTIONMetallurgical slags are the largest by-product of high temperature materials refining and extraction processes. The total amount of metallurgical slag produced in the year 2008 has been estimated at up to 422 million tonnes containing up to 222 TWh/y (Barati and Esfahani, 2011) of thermal energy. Over the past four decades attempts have been made to recover this substantial amount of energy as heat, electricity, or fuel, while none of the proposed method has been commercialized yet.During slow cooling the slag tends to crystallize the constituents (CaO, SiO2, Al2O3, etc.) into a hard, heavy solid. In the past, over 90% (Bengt, 1983) of the molten waste was discharged onto heaps and allowed to cool slowly, then crushed and used in road construction or land filling or as coarse aggregate for concrete. However, later it was found if cooled rapidly, the slag can be used as a substitute for Portland cement. As a result, processes such as wet granulation were created in which molten slag is fragmented with water, forming amorphous (glassy) phases. Despite its effectiveness in producing a suitable material, heat would not be recovered through this process. Thus, dry granulation was introduced in 1930’s and was developed further in 1970 – 1980’s."

Jan 1, 2012

By S. D. F. Rocha1, L. Katsarou, G. P. Demopoulos

"Crystalline scorodite (FeAsO4·2H2O) has been pointed out as the most stable compound to immobilize arsenic for disposal due to its good stability performance according to EPA’s TCLP test. However, in anaerobic conditions, arsenic releasing is increased to undesired levels due to scorodite reductive break down, in eh <100 mV at 5.5< pH <7 which causes contamination of groundwater. In this work, the concept of encapsulation by controlled deposition of mineral coatings immune to pH or redox potential variations is presented. Aluminum and calcium phosphates were evaluated as coatings and the release of arsenic from scorodite previously coated with phosphates was substantially decreased when compared to the VALUES (obtained from crude scorodite, both in oxic and anoxic conditions. INTRODUCTIONThe widely acknowledged hazardous properties of arsenic as a soil and natural water contaminant and its adverse health effects when present in drinking water have led to very strict environmental regulations (Mandal & Suzuki, 2002) aiming at the drastic reduction of the presence of arsenic in the effluents of the mining and metallurgical industries.In Canada, the Metal Mining Effluent Regulations (Government of Canada, 2002) dictate that the maximum monthly mean concentration in tailings for arsenic must be lower than 0.5 mg/L. At the same time the new Environmental Protection Agency’s (EPA) standard for drinking water foresees concentrations of arsenic less than 0.01 mg/L, which means that the leachability limit for the industrial waste is set at 1 mg/L arsenic (EPA, 1994; Le Berre et. al, 2007). One of the preoccupations of the mining and metallurgical industries is directed to the elimination of arsenic presence in all its effluents, especially since arsenic is commonly found in many ores mainly in the form of oxides and sulphides. After processing of arsenic-containing ores and concentrates, arsenic can be present either in solid residues and tailings, liquid effluents or in flue dusts. Several of these forms of arsenic waste materials are soluble and therefore may cause the contamination of ground water, if disposed of without further treatment."

Jan 1, 2012

By A. D. Davis

Limestone-based material shows great promise for removal of arsenic from water. In laboratory tests, it has removed more than 95% or arsenic and more than 99% of cadmium and lead. In addition, the waste material appears to be suitable for recycling or disposal in an ordinary landfill. However, the efficiency of limestone for arsenic removal could be improved. Recent research has shown that iron treatment of limestone can enhance its arsenic-removal efficiency greatly, increasing its attractiveness as an alternative to other methods.

Jan 1, 2012

By R. Siy, O. Neiman, B. Hilscher

"A full-scale prototype of “Jameson Downcomer” technology has been installed and tested on a Tailings Oil Recovery (TOR) vessel in Syncrude’s Mildred Lake extraction plant. Jameson Downcomers are a type of mineral flotation equipment used in the coal industry that Syncrude has extended to the recovery of secondary bitumen in the oil sand extraction process. The TOR vessels are currently being operated as single-gravity separation vessels, in series with the Primary Separation Vessels (PSV’s). We have developed a model to differentiate between “floating” and “non-floating” bitumen in the PSV’s, and then applied it to verify that the current TOR performance only captures the “floating” bitumen by simple separation. The existence of “non-floating” bitumen provides an opportunity for recovery enhancement by means of the Jameson Downcomers. To achieve bitumen recovery enhancement, middlings slurry is withdrawn from the TOR vessel, and passed through a number of parallel Jameson downcomers, within which the slurry is accelerated to a high-velocity free jet, and impinged upon the slurry surface inside the downcomer, in the presence of air. The aerated slurry is returned to the middlings zone inside the TOR, resulting in an incremental recovery improvement of bitumen in the TOR. The operation of the downcomers is thought to produce suitably small air bubbles for the flotation of bitumen, either by fluid shearing during the slurry jet impingement, and/or by micro-bubble nucleation. This full-scale prototype design has met or exceeded the recovery expectations of the original Research piloting, recovering at least 40% of the non-floating bitumen. In Syncrude Extraction, this provides high business value by a separation efficiency gain achieved with modest expenditure. As well, the system has demonstrated excellent operability and maintainability.INTRODUCTION Syncrude Overview Syncrude Canada Ltd. is one of the largest producers of crude oil from oil sands. Our crude oil production facility has the capacity to produce over 15% of Canada's total oil requirements. To do this, we surface mine oil sand, extract the raw oil known as bitumen from the sand using water-based processes, and upgrade that bitumen into sweet light crude oil by fluid coking, hydro processing, hydro treating and reblending. Our final product, Syncrude Crude Oil (SCO), is sent by pipeline to three Edmonton area refineries and to pipeline terminals which ship it to other refineries in Canada and the United States. The Syncrude operation is comprised of four major technology areas: Mining, Extraction, Upgrading and Utilities. As well, Syncrude invests more than $40 million annually in science and technology, and is among the top 50 companies in Canada for Research and Development (R&D) investment. Syncrude holds 21 active Canadian and U.S. patents."

Jan 1, 2012

By D. T. White

"Metallurgical extraction processes often call for the heating of aqueous slurries. Indirect heat exchangers are generally not feasible for service with high yield stress slurries because of low heat transfer rates. It is more appropriate to heat the slurry by direct contact, typically with steam as the heating medium. Although having a long and successful history, direct-contact heat transfer to aqueous slurries has been used without the support of pilot plant research. This paper provides results of the needed research, the work being done at a scale large enough to enable direct scale up to commercial operations. A pilot plant heater was constructed and tested to develop an understanding of the slurry heating process and to ensure that commercial scale heaters were appropriately sized.INTRODUCTIONPressure Leaching OperationsPressure leaching operations are often used to oxidise sulphide gold ores, or for extraction of nickel and cobalt from laterite ores with sulphuric acid. Where there is sufficient sulphur available, the exothermic pressure oxidation reactions can be self sustaining at temperatures as high as 225 ºC, without having to preheat the feed slurry. At lower sulphur levels, slurry preheating is required. This is typically achieved by utilising the flash steam released from the slurry letdown stages and contacting this directly with cold incoming slurry ahead of the autoclave. The vessels where this slurry-steam contact is made are known as heaters or condensers, with the number of pre-heat stages varying, depending on how much heat is evolved in the oxidation reaction (Mason, 1990).In nickel laterite pressure acid leaching processes, which operate between 245 and 270 ºC, the only significant exothermic reactions are those associated with dilution of sulphuric acid in the leach. As a consequence, slurry preheating with flash steam is always used commercially. In practice the number of flash steam preheating stages required varies from 1 to 3, driven by a number of factors, including other uses for flash steam and the upper temperature limit at which preheated slurry can be pumped. A diagram of a typical pressure acid leach train is shown in Figure 1.For pressure acid leaching operations and at low sulphur levels in pressure oxidation, boiler generated direct steam addition to the autoclave is required to sustain the reaction temperature. For this reason it is imperative that the flash steam – slurry heat transfer is efficient and the slurry temperature approaches that of the flash steam closely."

Jan 1, 2012

By S. Ragab

The objective of flotation models is to predict the recovery rate of minerals from a flotation cell. In this paper a CFD?based flotation models is presented. The model uses first order rate equation, and the collision frequency is estimated using Abrahamson [1] model with input from CFD two-phase simulations. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) are determined by the two-phase hydrodynamic simulations. Knowing these parameters throughout the machine is essential in understanding the effectiveness of different components (rotor, stator or disperser, jets) on the flotation efficiency. Not only the average pulp recovery rate can be estimated but also the regions of high/low recovery rate can be identified. The CFD-based flotation model presented here can be used to determine the dependence of recovery rate constant at any locality within the pulp on particle diameter, particle specific gravity, contact angle, and surface tension.

Jan 1, 2012

By Metehan Erdogan, Orhan Gökçe Göksu, Ishak Karakaya

"An experiment (mixture) design was created to optimize the process parameters of the electrochemical reduction of CaW04 to W in molten CaCl2-NaCl eutectic mixture. Temperature, applied voltage and the length of Kanthal wire winding of the CaW04 pellets were selected as the process parameters that were allowed to vary between the predetermined minimum and maximum values. The rates of the electrochemical reductions were interpreted from the variations of current and total charge vs. time graphs under different conditions. The analysis pointed out that 640°C and 2.81 V resulted in the fastest reduction. Itwas seen that the effect of Kanthal wire winding on the output current was less pronounced when compared to the other two parameters.IntroductionFFC Cambridge Process [1] has been applied to a number of metal oxides in laboratory experiments to produce metals. In nearly all of these studies, the electrolysis temperature was around 900°C, the electrolyte was pure CaCl2 or CaCl2 containing salt solutions and the anode was graphite. However, it was recently shown that the electrochemical reduction process of metal oxides in CaCl2 containing electrolytes at the mentioned high temperatures was not suitable for tungsten production [2], It was reported that as soon as WO3 contacts CaCl2, the following reaction occurs:"

Jan 1, 2012

By K. Fleck

Energy West Mining Company (EWMC) has implemented a geologic program for improving stability and support requirements along deep two-entry longwall gateroads at its Deer Creek Mine operations located near Huntington, Utah. Together with geotechnical monitoring and concurrent review of mine seismicity in cooperation with MTI staff, it has become possible to improve longwall layout designs for two seam extraction of the Hiawatha and Blind Canyon seams. The geologic program consists of surface and in-mine exploration drilling, surface and in-mine geologic mapping, rock mechanics testing and detailed measurements of changes in depositional and structural conditions during development of every longwall gateroad. The geotechnical program consists of underground measurements at seven locations in two neighboring mining districts located in the Hiawatha and Blind Canyon coal seams under moderate to deep cover. Within the last five years, additional measurements, including data on seismicity and face conditions, have been incorporated into the data collection program for verifying the insitu coal strength and load transfer mechanisms for improving two-seam designs and support systems. Geologic mapping results are also used to predict local stability of headgate and tailgate entries, combining mine roof mapping, stratigraphic profiles of the coal and roof, and depth-of-cover information and dual-seam mine overlays, for use by operations personnel in planning roof and rib support for the retreating longwall sections.

Jan 1, 2012

By D. Imeson, T. Grammatikopoulos, M. Aghamirian, M. Oliazadeh

"More than 70% of potash is produced worldwide by froth flotation. Flotation of potash was developed in the early 1930s. Amines are widely used for flotation of sylvite (KCl) from halite (NaCl) and insoluble materials such as clays. Amine collector is also absorbed by clays. Therefore, clays are usually separated by scrubbing and de-sliming prior to flotation. Alternatively, slimes can be floated ahead of potash flotation. Flotation recoveries of sylvite are commonly in the range of 85%, while losses can occur in slimes, flotation tailings and make-up of process brine. Ores containing free coarse-grained sylvite are generally screened, whereas both fine and coarse fractions are conditioned and floated separately. The unique features of potash flotation include solubility of sylvite in water, the size of particles floated and fast kinetics. Particles up to 2.3 mm can be floated and about 50% of flotation feed can be removed in the rougher stage in few minutes. The main challenges in potash flotation are the recovery of potash from slimes, flotation efficiency in the presence of carnallite and recovery of coarse potash grains. A review of potash flotation shows that there is still room for improvement in both coarse and fine potash flotation. The present paper reviews the most significant flotation parameters including reagent type and dosage, flotation circuits, flotation equipment size and new developments in potash flotation. The latter include new reagents, flotation technologies (Hydrofloat, Jameson and column cells) larger flotation cells and slimes flotation.INTRODUCTION Potash is the common industrial term for potassium in various chemical combinations and minerals soluble in water. About 90% of potash produced worldwide is used as agricultural fertilizers. Flotation is the main treatment process of sylvinite (KCl-NaCl) ores for recovery of sylvite (KCl). Potash concentrate should contain a minimum of 95% KCl and be relatively free from 0.2 mm KCl fines. The flotation process for beneficiation of potash ores was developed in United States and Russia concurrently in the early 1930s. In 1934, Potash Corporation of America applied flotation process in a commercial scale (Tippin R.B. and Huiatt J.L). In the initial application, halite (NaCl) was selectively floated by employing lead chloride as an activator and soap as collector. The sylvite concentrate was reported in the cell underflow."

Jan 1, 2012