Search Documents

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

By G. J. Simandl

"Since the 1980s, China has become the predominant producer of REEs. Recently, it introduced REE export quotas and this started a world-scale REE exploration rush. REE resources are concentrated in carbonatite-related deposits, peralkaline igneous rocks, pegmatites, REE ± P veins, ion adsorption clays, placers, and some deep ocean sediments. REEs could also be derived as a by-product of phosphate fertilizer, U processing, Ti-Zr-bearing placers, and exploitation of Olympic Dam-type sub-type of IOCG deposits. The ideal REE development target would be located in a politically stable jurisdiction such as Canada. REE grade and tonnage, mineralogy, and permissive metallurgy are some of the key technical factors that could be used to screen projects. INTRODUCTIONAccording to the International Union of Pure and Applied Chemistry (IUPAC), the term “rare earth elements” (REEs) encompasses yttrium (Y), scandium (Sc), and the lanthanide series: lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pm), samarium (Sm), europium (Eu), gadolinium (Gd), terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), and lutetium (Lu). This definition is used throughout this paper.REEs are subdivided into light (LREE) and heavy (HREE) categories. LREEs include, Sc, La, Ce, Pr, Nd, Sm, Eu, and Gd and HREE include Tb, Dy, Ho, Er, Tm, Yb, Lu, and Y. Promethium (Pm) does not occur in nature. Concentrations of individual LREEs in the upper crust of the Earth are comparable to those of base metals. Even the least abundant REE (Lu) is about 200 times more abundant than gold.The production of REEs, reported in the form of oxides (REOs), for 2011 is estimated at 140 000 t (Figure 1a). Although high technology industries can substitute several REEs with other materials, these substitutes are typically more expensive or less effective than the REEs they replace. A number of countries, including the United States, consider several REEs essential for national security, their economy, and a general reduction in green house gas emissions. The forecasted demand for individual LREOs is much higher than that of HREOs (Figure 2). Dy, Eu, Tb, Nd, and Y are essential for the US economy and subject to predicted supply disruptions (U.S. Department of Energy, 2010)."

Jan 1, 2012

By I-H. Jung, J. Kim

"Mg alloys are extensively used as light structural materials in modern industry. Mn and RE (rareearth) metals are effectively used as alloying elements to enhance the properties of Mg alloys. Therefore, the thermodynamic database of those alloys is important in the Mg alloy design and processing. Critical evaluation and optimization of all available literature data for the Mn-RE systems were conducted to obtain reliable thermodynamic functions. The Mn-RE systems shows systematic changes in the phase diagrams and thermodynamic properties with increasing atomic number in the lanthanide series. This systematic approach for all RE elements allows to resolve inconsistencies in the available experimental data. INTRODUCTIONRare Earth (RE) metals are widely used in many industrial fields including permanent magnet, electronic materials and structural materials. As a small addition of RE can enhance magnetic, electronic, optical and mechanical properties of numerous materials, the usage of the RE is still expanding regardless of the strategic control of their supply.Magnesium alloys are getting great scientific and industrial attention as the lightest structural materials. One of the drawbacks of Mg alloys is their poor formability at room temperature due to the limited slip system with hcp crystal structure. Recently, several studies (Farzadfar et al., 2011; Sandloebes et al., 2010; Stanford, 2010; Stanford et al., 2008; Yan et al., 2010) show that the additions of small amounts of RE can considerably enhance the ductility of Mg alloys. Therefore, a lot of research on Mg-RE alloys is undergoing to clarify the role of RE on the enhanced deformation mechanism and to find out the most optimum Mg alloy compositions. In order to respond to the need of Mg-RE alloy development, a large thermodynamic database for Mg alloys containing RE has been developed with critical systematic analysis and optimization of the entire RE series data. This includes the thermodynamic database of the Mg-RE (Kang et al., 2009), Mg-RE-RE (Kang et al., 2009), Mg-Al-RE (Jin et al., 2011; Jin et al., 2010), Mg-Zn-RE and Mg-Mn-RE systems."

Jan 1, 2012

By Yongzhong Xiao, Tiejun Chun, Jian Pan, Zhen He, Deqing Zhu

"In this paper, the reduction kinetics of low grade hematite ore was calculated. Mineralogy shows that the ROM (run of mine) ore is of low grade hematite ore type, assaying 27.2 wt% Fetotal and with main valuable minerals of hematite. The reduction kinetics shows that the reduction reaction rates of pellets with additive and without additive are all controlled by diffusion through the product layer. The calculated apparent activation energy of pellets with 12 wt% complex additive is 8.55 KJ/mol, dropping 62.23% compared to that of pellets without additive.IntroductionWith the rapid development of iron and steel industry in China, there has been a soaring demand for iron ores in the past decade. The imports of iron ores have increased from 148 million ton in 2003 to 620 million ton in 2010[1]. Therefore, large quantities of low grade iron resources are necessary to utilize in China at the moment. During the past years, extensive research has been carried out on the low grade hematite ores [2-6], such as reverse floatation, gravity separation, high-gradient magnetic separation and direct reduction-magnetic separation. Direct reduction-magnetic separation is an innovation way to treat the low grade hematite [7]. However, the research of reduction kinetics of low grade hematite is few. Some research about the reduction kinetics of reducing iron oxides by CO was studied [8]. The results indicated that the apparent activation energy is 8.0-28 KJ/mol when the reducing reaction is controlled by internal diffusion. The apparent activation energy is 50-75 KJ/mol when the reducing reaction is controlled by chemical reaction. In this paper, the reduction kinetics of pellets was also been studied."

Jan 1, 2012

By A. Taylor, M. Blanchette, J. Doucet

"A Z1600 Jameson Cell Test Rig was rented for test work at Vale’s Clarabelle Mill operation. This paper discusses the evolution of renting the unit for test purposes to owning the unit and operating it as a revenue generating process component. The paper focuses on three aspects of the Z1600 project; the initial rental and installation, the test work performed in the cleaning circuit, and the business factors which led to the unit being permanently incorporated into the copper circuit.INTRODUCTION Clarabelle Mill is located in Sudbury Ontario (approximately 350 km north of Toronto) on the southwest rim of the Sudbury basin a meteoric impact crater that is 62 km long and 30 km wide. The result of the meteoric impact was concentrated nickel (Ni), copper (Cu) and platinum group metal (PGM) ore bodies in the outer perimeter of the basin; described in more detail by Hanley (1957). Vale currently has seven operating mines in the Sudbury basin, from which nine distinct ore types are mined. Ores are also received from two QuadraFNX mines. Clarabelle Mill processes all of these ores for the Ontario Operations of Vale. The mill, commissioned in 1971, was originally built as one of four mills operated by then Inco Limited. Between the late 70’s and the early 90’s process changes were made to consolidate the Sudbury Operations milling processes into a single operating mill, Clarabelle Mill. In 1990, the SAG mill was installed resulting in peak mill throughput of 11.9 million short tons per annum (Mstpa), with typical throughputs of ~10 Mstpa. Mill average feed grades were 1.4% Cu and 1.2% Ni. During the resources boom, plans were developed to increase the mill capacity at Clarabelle Mill in stages to a final capacity of 13.5 Mstpa. The project known as the Clarabelle Mill Expansion and Recovery Project (CMERP) included expansion and reconfiguration of the grinding and flotation circuits. The first stage was a planned increase in grinding capacity with the reallocation of existing mills, the existing flotation capacity would be required to treat higher throughput until the new flotation circuit was constructed."

Jan 1, 2012

By S. Underwood

The tracer gas method of conducting ventilation surveys is a means of determining air quantity in underground mines with knowledge of the concentration of the tracer in the atmosphere and the flow rate at which the tracer is being released. The technique is useful in inaccessible areas of underground mines and areas where traditional point measurement of velocity is not practical. Sulfur hexafluoride (SF6) is the industry standard tracer(Kennedy 1987) used in underground mines because it is safe, stable, and not naturally occurring in the mine environment. The implementation of a second tracer will increase the versatility of the tracer gas technique allowing for simultaneous releases for the study of interrelated ventilation circuits, and for conducting multiple experiments in less time. This paper will detail the selection of perfluoromethylcyclohexane (PMCH) as a novel tracer with sensitivity, physical properties, and analysis characteristics similar to SF6. Methods for the release of liquid PMCH into underground mines will be recommended, and the vulnerabilities of sample loss due to condensation of vapor PMCH will be explored. Finally, the benefits and implications of using PMCH as a second tracer will be discussed.

Jan 1, 2012

By I. Perus, M. Fazarinc, G. Kugler, M. Tercelj

"Ledeburitic tool steels are highly alloyed steels used for specific highly loaded applications but are characterized by low and variable hot workability. In this contribution the importance of selecting the right choice of some essential process parameters, i.e. casting temperature, solidification rate and soaking temperature, needed for improving the intrinsic hot deformability of ledeburitic tool steels, is studied. An inappropriate selection of casting temperature and cooling rate results in precipitation of unusual eutectic carbides that decreases the hot workability, whereas with the selection of appropriate soaking temperature the temperature range of safe hot working can be broadened. For each initial as-cast microstructure individually determined soaking temperature should be selected.IntroductionThe surface cracking during hot deformation of ledeburitic tool steels reduces mechanical properties and their industrial yield. These tool steels have high hardness, wear resistance and high tempering resistance on one hand, and high flow stresses and low hot deformability on the other. Decreased hot deformability of the tool steels is attributed to the type, size, shape, distribution, fraction of eutectic carbides and/or other phases, grain growth, etc. at upper limit while precipitation of secondary carbides and decreased recrystallization rate at lower limit of the safe hot deformation temperature range, [1-6].The occurrence of cracks on most exposed areas of workpiece are related to the areas where similar conditions related to upper and/or lower limit of temperature working range prevail, i.e. areas with accelerated cooling, areas with higher value of accumulated strains where also decreased recrystallization rate with simultaneously presence of higher tensile stresses takes place, furthermore areas of workpiece which are due to combustion conditions in furnace heated to higher temperatures, etc. Thus the areas, where combination of previously mentioned conditions prevails, are more exposed to cracking. This additionally requires that hot deformability of ledeburitic tool steel should be considered as a complex problem. Publications in the literature with regards to hot deformability of tool steels are predominately of a partial nature thus all reasons for unexpected occurrence of cracks are not sufficiently explained in available literature so far. Furthermore modern practice proves that previous processing parameters significantly influence the hot deformability and thus this cannot be considered as a constant value. During heating, soaking and hot deformation various processes take place: decay (decomposition) of carbides, formation of new carbides, dissolution of carbides and of alloying elements, etc. Thus depending on variation of process parameters and chemical composition, that consequently influences the processes related to carbides, shifting of decreased deformability at both limits of temperature working range to higher and/or to lower temperatures can occur, [1-14]."

Jan 1, 2012

By Chuanfu Zhang, Liwei Liang, Yanxin Wu, Jinliang Wang

"According to the reaction shaft operation characteristics during the flash smelting process, 15 groups of slag samples containing high Fe3O4 were prepared by some chemical reagents, and then the slag viscosities were measured using a RTW-10 type synthetic test instrument for melt physical property by the rotating cylinder method. The effects of Fe/SiO2 ratio (mFe/mSiO2), Fe3O4 content (wFe3O4), Cu2o), MgO content (WMgO) and Cao content (wCaO) on the slag viscosity were also studied. Results show that slag viscosity is decreased with the increase of temperature, mFe/mSiO2, wCu2o, wMgO and wCao, and with the decrease of wFe3O4, under the range of slag contents: mFe/mSiO2 1.36~1.78, wFe3O4 17.83%~21.18%, wCu2o 3.51%~8.34%m wNgI 2.21%~6.57%m w/caI 6.22%~9.387% and temperature range if 1250 o/c~1450 oC. Only wFe3O4m and w/caO have great influence on the slag viscosity when temperatures as high as 1400 oC. Only wFe3O4 and wCaO have great influence on the slag viscosity when temperatures as high as 1400 oC or so. To form a freeze slag with higher viscosity inside the reaction shaft, wFe3O4 should be more than 20% and wCaO should be less then 6%.IntroductionSince its appearance in 1949, Outokumpu flash smelting technology has making continuous innovation and has become the most competitive intensified smelting technology [1], widely considered to be the standard clean smelting process [2]. At present, flash smelting technology is adopted to newly build or reconstruct most of the world's copper or nickel smelting enterprise [3]. Reaction shaft is the most important part of the flash smelting furnace. During the flash smelting process, reaction shaft must be able to withstand the following harsh conditions at the same time: 1) high temperature varying from 1400 °C to 1500 °C. 2) strong oxidative atmosphere containing 50% - 80% oxygen. 3) solid particles and melt with speed up to l00 m/s. 4) high acidic or basic slag with strong chemical corrosiveness. 5) smelting gas containing 50% - 80% SO2. 6) matte with strong dissolution."

Jan 1, 2012

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By K. Koruyan

Although remote sensing technology has been available for many years, it has rarely been used for monitoring mining activity. Recent studies indicate that remote sensing is also a valuable tool for managing and planning certain aspects of the mining operation. In this paper, we examine areal expansion of marble quarries and the affected vegetation over a period of 10 years in the Mugla region in Turkey, using geographic information system (GIS) and remote sensing (RS) techniques. Images captured by ASTER Level 3A01 (3D Ortho Data Set), Landsat 5, and Landsat 7 satellites between 2001 and 2009 were used for the analysis. Changes in the natural vegetation as a function of the production level in the marble quarry were calculated using the normalized difference vegetation index. According to the study results, land cover and natural vegetation decreased by less than 3 per cent and 1 per cent respectively between 2001 and 2009, following an upsurge in mining activity in the region.

Jan 1, 2012

By R. Boom, Y. V. Meteleva-Fischer, B. Kraaijveld, H. Kuntzel

"Segregation of impurities during refining of metallurgical grade silicon (MG-Si) is an option to produce solar grade silicon (SG-Si). Directional solidification is a last step in production of SG-Si effective for removal of metallic impurities. The possibility is investigated to use metallic impurities originally present in MG-Si for removing boron and phosphorus. MG-Si has been treated using two methods: 1) alloying with calcium and 2) refining with Na2O-CaO-SiO2 slag, both by controlled cooling. The microstructure of silicon and the impurities distribution have been studied before and after the treatments. Using EPMA phosphorus and boron have been detected in 1-2 wt% concentration range in several intermetallic compounds in grain boundaries after both treatments. This observation points to a different possible mechanism of silicon refining from boron and phosphorus. Controlled cooling improves migration of phosphorus and boron to the silicide phases in grain boundaries, which can be removed by acid leaching treatment.2. IntroductionStandards for silicon solar cells and growing demand on “green” energy require economical and efficient route to the production of solar grade silicon. Refining of cheap metallurgical grade silicon is one of the promising options, where application of existing metallurgical approaches can result in cost-efficient production on industrial scale. Focus in refining is on impurities, which are most difficult to remove: B, P, Al, Ti, due to their large segregation coefficient in silicon and low vapour pressure [1]. Moreover, more environmentally friendly technology in comparison to the traditional Siemens process [2] will be in accordance with societal needs. Based on properties of common impurities in metallurgical grade silicon, alloying refining and slag refining are suggested as competitive techniques having potential effect on removal of impurities harmful for conversion of solar energy [3, 4]. Alloying with Ca followed by acid leaching was found to be effective for removal of Fe and Ti from silicon [5] and to enhance also removal of boron [6] and phosphorus [7, 8]. In the work of Inoue et al. [8] drastically increasing removal of phosphorus from silicon has been observed with an increase of Ca content and a thermodynamics-based explanation was provided. Since phosphorus has been found to condense in the secondary precipitate mainly composed of CaSi2, it can be removed together with iron and titanium by consecutive acid leaching treatment. Slag refining is one of the metallurgical methods proposed to be effective for refining of metallurgical grade silicon from boron [9, 10]. Slags with additions of the following oxides to silica have shown positive effect on removal of boron: CaO [11-13], Na2O [11,14]. Mechanism of slag refining from boron is based on oxidation of boron followed by its incorporation in the slag network [9,11]; the same mechanism is suggested for refining from phosphorus taking into account that oxides of boron and phosphorus are known as network-formers [15]."

Jan 1, 2012

By Erik Westman

Few studies have been conducted regarding the location, movement, and relative magnitude of the rear abutment of a longwall coal mine. The rear abutment, or the abutment pressure arch in the gob area, is controlled primarily by the quality of pack of the gob; the more compacted the gob is, the larger the stress would be theoretically. While there is no definitive location for the rear abutment, early studies showed that it could be located as far back in the gob as 300 m (1,000 ft). Like the location of the rear abutment, there has been little research conducted and very few answers as to the exact magnitude of the rear abutment load. Due to the fact that the rear abutment has been studied considerably less than the front or side abutment, the need for further studies is evident. From a ground control standpoint, the location and magnitude of a rear abutment could reveal information on the caving process associated with longwall mining, such as when the initial cave could be expected to occur in future panels. Besides the possible importance of the rear abutment from a ground control perspective, evidence related to the longwall rear abutment could be vital from a ventilation standpoint. The peak rear abutment location could serve as an area for harmful gases, such as methane, to accumulate because forcing air through repacked rock is more difficult than through loose rock. The objective of this study is to determine whether passive seismic tomography could image the location, movement, and relative magnitude of the rear abutment as the longwall face retreated, in addition to the forward abutment and gob. The results of a passive seismic imaging study at a western US longwall show evidence for the location, movement, and relative magnitude of a rear abutment. A clear zone of highlystressed strata is shown where the forward abutment is expected and a low-velocity, damaged zone is shown behind the face where the gob is located. These two zones retreat with the face over a three-week period. In addition, the images show a return to stress levels behind the gob that are slightly higher than overburden stress levels, which is presumably the rear abutment. This occurs at a distance behind the face that is approximately the same as the face width for this mine. We can conclude that passive seismic imaging can be used to identify the location, movement, and relative magnitude of the rear abutment of a longwall mine. This conclusion is dependent on the use of appropriate data collection and processing methods. The information provided can benefit the both ground control and ventilation engineers as they strive to improve the safety and efficiency of longwall mines. The knowledge associated with the rear abutment of a longwall could not only help increase production through proper initial planning and reduce down time, but it could also make positive strides in improving the overall safety surrounding a longwall mining operation.

Jan 1, 2012

By R. Rumpold

The platinum group metals (PGMs) palladium, platinum, and rhodium represent the key materials for automotive exhaust gas treatment. Since there are currently no adequate alternatives, the importance of these metals for the automotive industry is steadily rising. The high value of PGMs in spent catalysts justifies their recycling. The state-of the-art technology is to melt the ceramic carrier and collect the precious fraction in a liquid metal bath. As the feed material has quite high melting points, huge amounts of energy are required for this process. Hydrometallurgical treatments of the spent catalysts offer the possibility to recycle the PGMs with less energy and time demands. Moreover, automotive catalysts contain further valuable materials to improve the exhaust gas treatment. These compounds, like cerium oxide, cannot be recovered in pyrometallurgical processes. This paper deals with a special process that uses hydrometallurgical principles to recycle the valuable metal fraction from spent automotive catalytic converters. Hydrochloric acid in combination with hydrogen peroxide is used as leaching agent. This combination selectively dissolves the PGMs and the cerium, which can be recovered in separate steps. As the leaching solution is regenerated and reused, wastewater generation is minimized. Furthermore, the process residues constitute potential byproducts.

Jan 1, 2012

By Tiejun Chun, Jian Pan, Deqing Zhu, Zhiyong Ruan

"In this paper, the desulfuration of pyrite cinder pellets was carried out. Phase analysis shows that most sulfur of pyrite cinder exists in the form of elementary sulfur. Most sulfur was removed in preheating stage. 81.25% sulfur was removed and the average SO2 concentration of exhaust gas was 1365ppm when the pellets were preheated at 950oC for 9 min. The final product, assaying 62.42wt%Fe and 0.02wt%S content at 96.88% desulfuration was achieved under the conditions of preheating at 950? for 9 min and roasting at 1200? for 15 min, which can be used as the burden for blast furnace.IntroductionPyrite cinder, as a subsidiary product of sulfuric acid production by roasting of pyrite ores, was solid waste in sulfuric acid enterprises. According to the statistics, the annual production of pyrite cinder is about 15 million tons in China. Besides, there is lots of pyrite cinder deposited for many years [1-3]. The pyrite cinder consumed in the cement and other industries as auxiliary additives only accounts for less 30% of its total discharge and the left is stored in waste pond, occupying much land and polluting environment in China [4-5]. Moreover, pyrite cinder contains iron between 30-63% which can be utilized as a cheap raw material for ironmaking by sintering or pelletizing processes, which can not only prevent pollution but also provide cheap raw materials for ironmaking [6-7]. However, compared to traditional iron ore concentrate, pyrite cinder possesses higher sulfur content."

Jan 1, 2012

By George W. MacDonald

ALFRED NOBEL was born at Stockholm on October 21st. 1833, and died on December 10th, 1896. Although Sobrero’s discovery of nitroglycerin dated back to 1847, this explosive was manufactured on a commercial scale for the first time in 1862, by Nobel at a factory which he erected at Heleneborg, near Stockholm. These works were entirely wrecked by an explosion in 1864. In 1865, he erected works, which are still in existence, at Winterviken, near Stockholm. In 1864 Nobel introduced modifications in the manufacture of nitroglycerin which were the subject of a patent (see footnote No. 1), and at the same time, claimed a process for the detonation of nitroglycerin. Nobel states that, up to that time, the method used for the manufacture of nitroglycerin consisted in pouring glycerin, drop by drop, into a mixture of sulphuric acid and nitric acid contained in a refrigerating mixture. In order that the nitroglycerin should not be decomposed, the temperature was not allowed to rise above 0° C.

Jan 1, 2012

By Keith Henderson

An open pit quarry operation in West Central Illinois provided a challenging proposition regarding the removal of a rock wall that once separated two pits, but was now in the middle of the north wall of the combined pit. Their mining plan included the development of a new ramp into the quarry pit in order to lessen the slope and to shorten haul truck cycle time. The task would be to remove a section of rock left behind from mining operations more than 20 years ago that was at or near the bottom of the designed ramp.

Jan 1, 2012

By H. Kinilakodi

The authors previously had developed a methodology that combines injury and citation measures into an overall mine safety performance evaluation tool, called the Safe Performance Index (SPI). It can be easily adopted by mine operators to monitor trends in their injury and citation experiences as a risk assessment method. In this paper, six normalized safety measures and the SPI are used to evaluate the risk that existed at mines in the two years preceding the occurrence of a fatality. The percentage of mines is given for which the risk was high or where trends of some of the safety measures indicated moderate risk. In 50% of the mines, this mine safety performance tracking method could have been helpful to the companies, state agency, or MSHA in recognizing and addressing emerging problems with actions that may have been able to prevent high-risk conditions, the fatality, and/or other serious injuries. The approach would have given scrutiny to the risk for mines that encompassed 74% of the fatalities during 2007-2010.

Jan 1, 2012

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level. It is situated in a wide east-west valley. Minera Peñasquito, S.A. de C.V., wholly owned subsidiary of Goldcorp Inc. has operated twin SABC-flotation lines since June 2010. Each line is capable of processing 50,000 tonne per day using a SABC grinding circuit followed by flotation to produce lead and zinc concentrates. The addition of a Polysius Polycom HPGR 2417 with dual 3,000 kW drives to reduce the crushed pebbles produced by the SAG mills was planned to increase production to 65,000 tonne per day per line. The production has been limited to 100,000 tpd due to operating issues in the grinding circuit. The operating issue has been the amount of pebbles generated by the SAG mills is significantly less than originally planned. This paper describes the planned installation of a crushed augmented feed to maximize utilization of the HPGR capacity. This coupled with full utilization of the SAG and Ball Mill available energies there is the potential to achieve a 50% total capacity increase from the grinding circuit.

Jan 1, 2012

By J. Engels

CODELCO is considering the implementation of high-density tailings management at the Chuquicamata mine in northern Chile for its long term disposal plan. To achieve this, CODELCO commissioned the design, construction, and operation of a 70 t/d pilot plant, fed by existing tailings. The testing programme was completed in May 2011, and consisted of laboratory rheological and characterization assessments, pipe loop testing, beaching trials, and analyses of deposition behaviour for solid contents ranging from 57?68% (w/w). This paper describes the characteristics of the pilot plant, the testing programme, the beach trial analyses, and the resulting beach profile predictions based on the stream power theory. CODELCO also used other predictive beach slope methods, such as the equilibrium slope concept, which are not discussed in this paper. The final beach profile for design will be selected after an expert analysis of all methods has been completed.

Jan 1, 2012

By K. M. Murphy, M. B. Wittrup

ABSTRACT The Saskatchewan Ministry of Environment recognizes the importance of environmental protection as an important contributor to Saskatchewan’s economy, with the environmental performance of industry closely monitored. Unfortunately, environmental regulation is often accompanied by significant process that does not always add value to environmental protection activities. The Saskatchewan Ministry of Environment has embarked on a visionary restructuring of its regulatory framework from conventional command and control regulation to a results-based regulatory framework. This new regulatory framework will provide for establishing clear environmental protection and resource management objectives; streamlining the environmental acts and regulations; developing an environmental code of practice; relying on qualified persons; enhancing compliance and enforcement tools; eliminating of many permits; and developing greater certainty in environmental assessment decisions. Results-based regulation promises to deliver enhanced environmental protection with less process. The uranium industry in Saskatchewan will be used as an example of the potential effects of results-based regulation.

Jan 1, 2012