Search Documents

By T. Bhambhani, D. R. Nagaraj

"Ultramafic Ni ores present significant challenges in processing in that both recoveries and grades are not satisfactory, due to the presence of Mg silicates in large amounts. Significant quantities of xanthates and CMCs are generally used for their recovery by flotation. Additionally, given that some of these ores are processed under acidic conditions, CS2 generation due to xanthate decomposition presents some safety hazards. Technology to replace xanthate has been developed for which the safety and health issues are absent. Collector S-10294 shows significant improvements in Ni and overall S recovery at a dosing rate of one half that of xanthate. New polymeric modifiers have also been developed that help reduce the Mg content of the concentrates at very low dosages. The reagents are custom designed for use in normal or hypersaline water, and acid or alkaline conditions.INTRODUCTION The use of xanthates in sulfide mineral flotation is reported to have started as early as 1925 (Nagaraj 2005). The reagent is now ubiquitous in the mining industry, accounting for 40-50% of total collector consumption. In recent years, the development of more selective reagents has rendered xanthates largely obsolete in Cu flotation. However, xanthates continue to be sold in large amounts in the Au, PGM and Ni flotation industry, where bulk sulfide flotation is required. The low cost and easy availability is the largest driver for the use of xanthates in the minerals industry. Of particular interest to this study is the use of xanthates in the flotation of Ni sulfide ores. About 60% of the world’s annual nickel output is obtained from sulfide Ni ores (Hoatson, 2006). A strategically important category of these ores is the ultramafic hosted sulfides, such as those of Western Australia and Canada. These ores are characterized by low Ni grades (<1%), with the Ni minerals being pentlandite, violarite, millerite and mackinawite, and gangue minerals comprising an array of altered Mg silicates, mostly serpentines. The challenges associated with treating these ores are well documented (Eltham et al. 1973; Claridge et al. 1975). One challenge is that Ni recoveries from these ores are lower. This has been attributed to the increased pulp viscosity, as discussed in detail by Vasudevan et al., 2010. Additionally, Mg silicates tend to report to the concentrate in large quantities, which is problematic for two reasons: a) concentrate dilution, and b) the high melting point of Mg silicates tends accelerate wear on the refractory lining of smelters. This has been attributed to network transport to the froth phase via bubble flux and entrainment (Patra et al, 2010)."

Jan 1, 2012

The accompanying supply/demand flow diagrams and 10-year tables for mineral and fuel commodities present essential data required by government, industry, and others to formulate policies and programs that can help assure an adequate and continuing supply of mineral raw materials. The 10-year data base terminates with 1974 figures because adequate world information was not available beyond that date. The selected mineral supply/demand tables and flow diagrams comprise but one "output" from the massive body of information and data collected and com-piled by the Bureau of Mines on a continuing basis covering mineral production, consumption, prices, shipments, imports, exports, and stocks, as well as industry activities in all States and abroad.

Jan 1, 2012

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly &apos;safe&apos; compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

By M. Cuba

Geostatistical modelling aims at providing unbiased estimates of the grades of elements of economic interest in mining operations, and assessing the associated uncertainty in these resources and reserves. Conventional practice consists of using the data as error-free values and performing the typical steps of data analysis - domaining, semivariogram analysis, and estimation/simulation. However, in many mature deposits, information comes from different drilling campaigns that were sometimes completed decades ago, when little or no quality assurance and quality control (QA/AC) procedures were available. Although this legacy data may have significant sampling errors, it provides valuable information and should be combined with more recent data that has been subject to strict QA/QC procedures. In this paper we show that ignoring the errors associated with sample data considerably underestimates the uncertainty (and consequently the economic risk) associated with a mining project. We also provide a methodology to combine data with different sampling errors, thus preserving the relevant global and local statistics. The method consists of constructing consistent simulated sets of values at the sample locations, in order to reproduce the error of each drilling campaign and the spatial correlation of the grades. It is based on a Gibbs sampler, where at every sample location, the actual sample value (with error) is removed and a conditional distribution is calculated from simulated values at nearby sample locations. A value is drawn from that distribution and kept only if it satisfies some statistical requirements-specifically, the global relative error and local means and variances must be reproduced. All sample locations are visited and simulated sample values are generated iteratively, until the required statistics are satisfactorily attained over all sample locations. This generates one realization of possible sample values, respecting the fact that the actual samples are known to carry an error given by the global relative error. Multiple realizations of simulated sample values can be obtained by repeating the procedure. At the end of this procedure, at every sample location a set of simulated sample values is available that accounts for the imprecision of the information. Furthermore, within each realization, the simulated sample values are consistent with each other, reproducing the spatial continuity and local statistics. These simulated sets of sample values can then be used as input to conventional simulation on a full grid to assess the uncertainty in the final resources over large volumes. The methodology is presented and demonstrated using a synthetic data-set for clarity.

Jan 1, 2012

In China, thin coal seams are rich in resources but are technically challenging. The mineable reserves in these seams account for 20.4% of the total coal resources, while the current production accounts for only 10.4% of the total annual production. Characteristics such as narrow mining space, low level of mechanization, poor working environment, and high cost of mining, restrict the development of mining safety and efficiency. Recently, fully mechanized mining technology has developed rapidly for thin coal seams, the level of yield and efficiency has reached or exceeded the international standard, and some state-owned key coal mines are considering automation of their mining process. In thin coal seams with hard stone bands that contain concentrations of pyrite, a specialized software, LS-DYNA, is used to calculate the rational blasting parameters that are used in the deep-hole pre-splitting blasting. Using this method the hard stone bands are fractured effectively, and hence increasing the coal productivity. In addition, mining advance rate were increased by enhancing the level of fully mechanized equipment and safety improved by increasing gas drainage from the gas outburst prone seam located some 7 m below the coal horizon. At present, thin coal seam mining technology faces many challenges, including the low level of equipment automation, the low advance rate in mixed coal-rock ground, and the large number of the mine personnel underground. By lowering the labour intensity and improving efficiency through automation and other measures, more efficient working faces can be implemented in thin coal seams.

Jan 1, 2012

By R. J. Jewell

The storage capacity of any given tailings storage facility (TSF) is a function of the volume available for the tailings, for which the geometry of the final upper surface of the tailings is most important. One of the advantages that can be obtained from thickening tailings prior to discharge is that the tailings can be stacked at a steeper beach angle than is obtainable with conventional low-density slurries. However, there is at present no universally accepted method available for the accurate prediction of tailings beach slopes. This paper examines the current situation with the objective of putting the quest for a method for the accurate prediction of beach slopes into perspective. The paper references published reviews of the best-known beach slope prediction methods. However, there do not appear to be any independently verified projects or published references to projects on which a Class A prediction has been validated for any of these approaches, and in those instances where projects have been implemented correlation of actual with predicted slopes has been poor - often due to differences between the properties of the tailings assumed in the design and those actually achieved in the field. The author also concludes that flume-scale testing cannot be taken as a reliable indicator of full-scale performance, and suggests that the outcome of any current predictive method should be used by experienced practitioners as only one of a range of indicators in order to suggest a range of slope angles likely to result for any given operation. Practice has shown that it is possible to manipulate beach slopes by changes to the disposal technique, such as limiting the rate of discharge per discharge point and by increasing or decreasing yield stress, but the impact of these changes cannot readily be predicted. There are also newly emerging technologies, such as the injection of a polymer into the tailings at discharge, that will enhance the dewatering of tailings and hence expedite the consolidation of the tailings, that could well facilitate the development of steeper beach slopes. The overall conclusion is that with the current state of knowledge, the accurate prediction of beach slopes is not possible. Furthermore, in view of the inherent variability of the tailings parameters from any operation, it may well be of more value to concentrate on developing an understanding of the means by which the tailings parameters may be manipulated by the operators to achieve a given beach slope than to concentrate wholly on developing a generic beach slope prediction model.

Jan 1, 2012

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer&apos;s perspective and from an equipment supplier&apos;s perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By Adrian Dance

Newmont Ghana Gold Limited?s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto- Mill projects, PTI?s methodology is termed Process Integration & Optimisation (PIO). Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit. Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended. A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI?s SmartTag? system. The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material. This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput.

Jan 1, 2012

By K. Mondal

A macroscopic approach integrated with microscopic analyses for wettability characterization is presented. Wetting depends on 1) Contact between the dust and the fluid droplets, 2) Wettability of the particles by the wetting fluid, and 3) Wettability rate (due to low contact times). The goal of this paper is to show that the wetting rate is a significant factor in dust control. Samples from the roof, three different horizons of the coal seam and the floor were pulverized to less than 25 µm. Experiments were conducted with known wetting fluids to correlate surface tension and equilibrium wettability. Further analyses were performed in terms of surface charge (zeta potential), particle size, mineral composition, elemental composition, and quartz content. The surface tension reduction was also achieved by the use of chemicals and/or altering the temperature of the water. Two methods were used to evaluate wettability rates: a) near real-time comparison of wettability rates, and b) comprehensive evaluation of the intrinsic wettability rates. The data obtained provides meaningful insights towards the design of engineering controls for an economical solution to dust control in coal mines.

Jan 1, 2012

By E. P. Wiechmann, J. A. Henríquez, P. E. Aqueveque, L. G. Muñoz, G. A. Vidal

"The original segmented intercell Optibar succeeded in reducing the magnitude and occurrence of short circuits. It also improved the specific energy consumption of the process. This paper expands the load current source concept introducing a triple segmented bar. This new bar adds immunity to dirt contacts and open circuits. Moreover, it further improves the standard deviation of current densities. As compared with industrial practices this development should accomplish an 8% specific energy reduction. Also, a plant implemented with BBS should be able to work with 12.5% higher process currents than Walker without compromising the operation.INTRODUCTIONIn 2011 the technology based on current mode was implemented at industrial scale. The success of this technology moved CIM Magazine (Lanktree, 2011) to write in the Jan 2012 issue an upfront story of this technological innovation. To cover the story, the technical reporter Graham Langtree was appointed by Peter Braul Editor of the upfront section. The article tells that “More than 40,000 tonnes of copper have been refined in a year-long test run of Optibar Inc.’s new technology at Barrick Gold’s Zaldívar copper plant in northern Chile. The new segmented intercell bars being used in the Compañía Minera Zaldívar refinery have slashed energy costs, reduced short circuits during refining and allowed the production of heftier, purer sheets of copper – gains that all promise to boost the plant’s margins. A copper refining tank house containing the cell circuits typically consumes 2,000 kWh of electricity to produce a single tonne of grade-A copper. Yet, monitoring the energy efficiency of the Optibar technology after increasing the weight of harvested copper sheets, the project’s engineers recorded a 92 kWh-per-tonne cut in energy consumption, a savings of 4.6 per cent. “Today, with the power prices we have, Optibar technology represents a potential savings for the whole plant of US$1.5 million per year,” says Robert Mayne- Nicholls, executive general manager of Barrick Gold’s Chilean operations.”"

Jan 1, 2012

By Harry Verakis, Thomas Lobb

Blasting accident data over a 30-year period (1980-2010) are summarized and presented for all types of surface and underground mining operations in the USA. The historical record of injuries from blasting accidents in all types of mines continues to show a significant decline. The overall decline in mine blasting injuries in the U.S.A. has resulted from advancements in blasting technology, training and improvements in blasting products and blasting processes. Some of the technology advancements such as safer blasting agents and computerized bulk vehicle loading, electronic detonators and remote operated blasting systems, and computerized blast design have and continue to significantly contribute to improvements in the historical blasting safety record. Also, the progress of significantly improving the safety of mine blasting has resulted from the combined efforts of miners, mine companies and operators, miners, unions, explosive and blasting product manufacturers, associations such as the International Society of Explosives Engineers and the Institute of Makers of Explosives and various government agencies.

Jan 1, 2012

By Wen Chen, Xinghua Liu, Zeyou Peng, Qiulin Wang

"Limonite is a collective for iron hydroxide argillaceous materials. It is very difficult to be treated due to the wide variation in specific gravity and magnetism and the high argillization rate in the course of grinding and beneficiation. The iron ore in Huangmei, Hubei, China is the typical representative of limonite. If the limonite is processed using conventional physical beneficiation methods (e.g. magnetic separation, gravity separation, flocculation-desliming-flotation, or a combined process of the three), it can only be obtained an iron concentrate grade of 51.98% and an iron metal recovery of 86.64%. However, the technique of flash magnetic roasting-magnetic separation can improve the concentrate grade to 61.03%, iron recovery to 91.17%. This paper describes the tests of recovering limonite by flash magnetic roasting in detail.IntroductionLimonite (mFe2O3, nH2O)[1] is a general designation for hydrous iron hydroxides and argillaceous matters. Limonite is hard to be separated because of its complicated geneses, comparatively weak magnetism, nonuniform grain size and being easily slimed during grinding. So most small and medium enterprises sell deslimed limonite product which was dealt with just by simple methods of washing, magnetic separation or gravity separation and so on. In recent years with the iron ore prices soaring, significant progress was made in mineral processing research of limonite. Laboratory research and industrial test results showed that flocculation-desliming-flotation process and roasting-magnetic separation process are the two best methods to recover limonite till now. To compare these two methods, roasting-magnetic separation process is superior to flocculation-desliming-flotation process in aspects of beneficiation indexes and industrial stability."

Jan 1, 2012

By A. S. Haugh

OHSAS 18001 is a series of international standards for occupational health and safety management. It is comprised of two parts, 18001 and 180029. OHSAS 18001 was formulated by international certifying bodies and is based on BS8800 and was first published in 19996,11. OHSAS 18001 was developed to be compatible with ISO 9001 and ISO 14001 in order to facilitate integration of quality, environment, and occupational health and safety management systems5. It is a voluntary standard and the overall aim of OHSAS 18001 is to enable organizations to control their occupational health and safety (OH&S) risks and improve overall health and safety performance5. OHSAS 18001 is widely accepted in the UK, Europe, and Asia, is gaining momentum in North and South America, and it was used as the basis and conforms to the requirements of ANSI/AIHA Z.10-2005: American National Standard for Occupational Health and Safety Management Systems. It defines a set of requirements for an occupational health and safety management system suitable for any kind and size of organization4. Businesses of all sizes are developing and implementing occupational health and safety management systems (OHSMS) that are in compliance with the OHSAS 18001 standard.

Jan 1, 2012

By J. D. Clucas, N. Verbaan, T. Grammatikopoulos, D. B. Dreisinger, C. Forstner, M. Aghamirian

"Search Minerals is currently exploring the Port Hope Simpson (PHS) Rare Earth Element District in southeastern Labrador, Canada. The Foxtrot Rare Earth Element (REE) Project in the PHS District has a 43-101 resource estimate consisting of 3,410,000 tonnes of Indicated Mineral Resources and 5,850,000 tonnes of Inferred Mineral Resources. The indicated and inferred resources contain 1.07% and 0.98% total rare earth element oxide (including yttrium), respectively. The dysprosium and neodymium grades are particularly attractive at 218 ppm Dy2O3 and 1687 ppm Nd2O3 for the indicated resources and 208 ppm Dy2O3 and 1494 ppm Nd2O3 for the inferred resources. The mineralization remains open along strike and at depth and is only one of a number of attractive exploration targets in the Port Hope Simpson area. The REE minerals fergusonite and allanite are present. The ore can be beneficiated by gravity, magnetic separation and flotation to a recovery of +80% for the individual REE. Acid bake and water leaching may be used to extract REE into solution for subsequent purification and recovery. The extraction range for single stage leach tests were 91-96% for Nd, 84-87% for Tm and 92-94 % for Dy with modest acid consumptions. INTRODUCTIONSearch Minerals Inc. (Search) is exploring the 100% owned Port Hope - Simpson District in Labrador, Canada for rare earth elements (REE). This District is approximately 135 km by 12 km in size, and is highly prospective for heavy and light rare earth elements. A total of 11 REE prospects have been discovered in the District to date, including the Foxtrot. In addition, Search is exploring in the 100% owned Henley Harbour region and has joint ventures with Quest Rare Minerals in the Strange Lake region, and with Great Western Minerals Group in the Red Wine complex, all in Labrador. These exploration locations are illustrated in the Figure 1. The focus of this paper is the investigation of the mineralogy and processing of Foxtrot REE materials. The Foxtrot resource falls within the claims held by Search in the Port Hope Simpson REE District. The infrastructure available at Foxtrot is excellent with a deep water port, air strip and road and power infrastructure at Port Hope Simpson. Over $7 Million has been spent to date on exploration and development of the District. The Foxtrot has been explored using prospecting geochemical methods, geophysics (airborne and ground), channel sampling of surface outcrops, mapping and three phases of drilling (18,934 m total)."

Jan 1, 2012

By C. Cornejo, C. Schuffeneger, J. Rosas

"At the end of 2010 the AMSA Esperanza Concentrator started commissioning. Located in the Atacama Desert this project is the first of several large size concentrators developed recently to operate in Northern Chile. In addition to the new operations to be implemented in the short term, many existing installations are planning expansions. The use of large size equipment is one of the common characteristics of the new concentrators, but also new technologies are being considered and innovation is present in most cases. Sea water or desalinated water will be required to process large tonnages of sulphide copper ores as well as gold bearing ores, since process water supply from the Andes will no longer be available. The high cost of sea water or desalinated water supply and the high cost of energy are not a limitation as the current metal market scenario allows obtaining an attractive NPV even from installations designed to process relatively low grade ores. A review of the current concentrators being developed in Chile is presented, including a description of the main design issues related to technology and innovation. An analysis of the Chilean mining industry is also presented, detailing mine and plant capacities as well as expected final products.INTRODUCTION The mining sector in Chile has become a reference when analysing the large concentrator plants projected or currently in operation all over the world. At present and as a consequence of the high price of metal commodities, most South American countries have an active mining sector. Chile is known as a major producer of metals. First records of copper production exported to Spain are dated to the early XVII century. Since then Chile has produced over 13% of the total copper ever produced in the world. After 1990 Chilean mining and the associated cluster of activities has substantially grown to levels never reached before, especially in the production of copper, gold and other non-metallic minerals. This dramatic increase is the result of an economic policy based on delivering comparative advantages and incentives for the admission of foreign capital to offset the weak domestic investment in previous decades. Massive mining of its huge mineral resources has allowed Chile to be a world leader in the production of copper and other base metals and mineral products."

Jan 1, 2012

By G. I. McPhail

The authors have conducted several investigations into the prediction of the beach profile of high-density tailings and have found that there are a number of important considerations that need to be taken into account over and above the reliability of the beach profile prediction methodology. These considerations relate to the chemistry of the slurry and specifically the influence of pH and flocculation, both of which have a significant influence on the rheology of the slurry at the discharge point. A number of examples are discussed and a potential testing protocol that will assist in assessing the influence of chemistry ahead of the beach profile predictions is presented. A methodology for assimilating the results of the testing into the likely field situation is discussed, and suggestions are made on application of the results in beach profile prediction. The suspected influence of residual flocculation on the stratification

Jan 1, 2012

By Mohamad Omarei, S. M. Sadrameli

"The aim of this research work was to produce biodiesel (fatty acid methyl esters, FAME) from canola oil using KOH loaded on y-Al203 support as a heterogeneous catalyst. Different parameters such as effects of the molar ratio of methanol to oil, catalyst amount and reaction time on the yield were investigated. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were used for characterization of the catalysts. A biodiesel yield of 86.67% was obtained under catalyst preparation and transesterification conditions of calcinations temperature of 773 K, 4 h of reaction time at 338 K, and using 3.5 wt% catalysts and molar ratio of methanol/oil of 15:1. The leaching of potassium species in the spent catalyst was observed.1. IntroductionBiodiesel is an eco-friendly and alternative energy source for diesel engines that can be synthesized by transesterfication of vegetable oil or animal fat with alcohols [1 ]. There are four principal approaches to the synthesis of biodiesel involving the transesterification of the triglycerides of the plant oils and animal fats: base catalysis [2], acid catalysis [3-5], employing supercritical alcohol conditions [6] and enzyme catalysis [7]. The commonly used homogeneous catalysts are NaOH, KOH and their alkoxides. Homogeneous alkali-catalyzed transesterification is much faster than acidcatalyzed transesterfication [8]. However, a large amount of water is required to transfer the catalysts from the organic phase to a water phase after the reaction. Therefore, it is considerably more costly to separate the catalyst from the produced solution [9]. These disadvantages could be removed by use of a heterogeneous catalyst [10]. The use of heterogeneous catalysts eliminates the neutralization step, hence it results much easier to separate from liquid products. Also, they can be designed to give a higher activity and selectivity and to have longer catalyst lifetimes [11]. A large number of different heterogeneous catalysts have been synthesized for biodiesel production. For example, calcined Mg-Al hydrotalcites [12], zeolite and metal catalysts [13], metal oxides such as calcium oxide (CaO) [14], magnesium oxide (MgO) [15], zirconium oxide (Zr02) [16], and supported catalysts [17] have been investigated as heterogeneous catalysts. CaO and MgO are most frequently used heterogeneous catalysts for biodiesel production [18]. In this present work, we aimed at developing an efficient catalyst for transesterification of canola oil. We have prepared KOH/ Al203 by impregnation and applied to determine the optimum conditions for biodiesel production. Three different variables including reaction time , alcohol to oil molar ratio and catalyst loading with may influence the quality of the produced biodiesel were optimized. Moreover, SEM (scan electron microscope), XRD (X-ray diffraction) and XRF were used for characterization of the catalysts."

Jan 1, 2012

By Fathi Abdrabbo

Open caissons are used for many geotechnical engineering applications. Open caissons may be used as deep foundation elements bypassing weak soils to tip in firm deeper strata, and in rivers and maritime construction to reduce the risk of scour. Open caissons are also used for collecting sewage water through gravity sewer pipe networks or from sewer force mains. In such applications, the design and construction of open caissons require a detailed soil investigation program. In this way, the design and construction plan of an open caisson can be developed with full knowledge of the prevailing subsoil conditions. The engineering and construction techniques are key factors to achieve functional caissons. Based on close observations during construction stages, the current study presents some challenges that were encountered during the construction of two open caissons of internal diameters 20 m and 10 m (65.6 ft and 32.8 ft). This paper describes the procedure followed to alleviate the construction difficulties encountered. Site exploration program and control measures required to satisfy design and construction requirements are crucial aspects. Sinking of open caissons in dense or very dense sands is risky. Incorrect sinking of open caissons may cause extra cost, delay in construction, and harm to nearby structures. Air/water jetting near the cutting edge of an open caisson, outside slurry trench, and/or inside open trench may be used to drive an open caisson downward. Unsymmetrical work around an open caisson may lead to tilting of the caisson. If this occurs, the tilt should be immediately corrected before resuming the sinking process. Improper cleaning of fine materials on the caisson?s excavation bed, and/or inappropriate pouring of underwater concrete may result in a defective concrete seal. The paper contains a series of practical guidelines to assist those intending to use open caissons, and shares good caisson sinking practice with practitioners. Finally, the study aims to understand the difficulties encountered and to anticipate future problems.

Jan 1, 2012

Mining steeply dipping coal seams is a difficult task in the mining industry. Prior to 1996, fully mechanized longwall mining methods along the seam strike direction were tried in China and other countries. Due to its larger coal reserve in steep seams, China made more but still limited progresses on mining in such seams than the other major coal-mining countries. In the last two decades, accelerated research efforts have been made to improve the mining technology in steeply dipping coal seams. Based on these works, a dynamic model of ?R-S-F? system under asymmetrical constrains in mining steep seam is established and the theory of strata control and hazard prevention begin to be formed. The key technologies for mining steep coal seams include: global and regional strata control methods in longwall face, methods for the longwall face machines to sustain static and dynamic loads, and flexible protection technology. These theory and technologies have been successfully applied to mining of steep coal seams of varying thickness and hardness, with hard and soft roof and floor, and with high potential of spontaneous combustion in China. In the recent years, the technology has been introduced to Russia, India, Uzbekistan and other countries where steep coal seams are mined.

Jan 1, 2012

By Alex Luyima, Honglan Shi, Lifeng Zhang, Yongqing Jiang

"Leaching process has been suggested to recover most metals from waste PWBs. In this study, the leaching behavior of most metals present in waste PWBs is evaluated before and thermal treatment. Different leaching acids: hydrochloric acid (HCl), nitric acid (HNO3) and aqua regia are compared. The effects of acid concentration, particle size of sample, leaching time and temperature are examined. Results revealed that most metals are present in small particle size and sequential leaching of PWBs with a combination of HCl acid and aqua regia is capable of dissolving most of the metals content of PWBs. Leaching of thermally treated PWBs produced the highest leaching percentages for similar leaching conditions.IntroductionApproximately 20–50 million tonnes of electronic waste (e-waste) is produced globally per year. Waste Electrical and Electronic Equipment (WEEE) or E-waste is one of the fastest growing waste streams in the world. In developed countries, it equals 1% of total solid waste on an average [1]. The growing stockpile of used and obsolete consumer electronics has been called the “largest toxic waste problem of the 21st century [2]. Printed wiring boards (PWBs) is an essential part of almost all WEEE, and accounts approximately 3% of all WEEE by weight [3]. PWBs are a platform upon which microelectronic components are mounted. PWBs contain metals (~40 wt. %), ceramics (~30 wt. %) and plastics (~30 wt. %) [4]. The metallic part includes; Cu, Pb, Zn, Fe, Cd, Be, Cr, Au, Pt, Pd, Ag, etc. The plastic part of the PWBs is mostly epoxy resins. These plastic resins also contain very toxic halogenated flame retardants (HFRs) [5]."

Jan 1, 2012