Search Documents

By H Kusumi, A Nishio, K D. Halim, Y Yun

In Japan, evaluation of rock mass is crucial in mountain tunnels that are constructed using the NATM (New Austrian Tunneling Method) to determine the support pattern that in turns determine the final support structure of the tunnel. The current evaluation method is highly dependent on the observations of on-site expert engineers that grades the rock mass in four levels across nine criteria: A. Condition of tunnel face. B. Condition of excavated surface. C. Compressive rock strength. D. Weathering. E. Spacing of discontinuity. F. Condition of discontinuity. G. Orientation of discontinuity. H. Spring water. I. Water degradation. However, in recent years, the number of said experts are decreasing rapidly due to labour shortage caused mainly by an aging population and declining birth rates. This is one of the biggest challenges that the construction sector currently faces, and this may affect the efficiency of tunnel construction projects in the future. Thus, this study proposes the implementation of a deep learning tool called the convolutional neural network (CNN) to quantitatively evaluate rock fractures on tunnel face. In addition, Gradient-weighted Class Activation Mapping (Grad-CAM) is applied to visualise CNN, as well as verify the applicability of CNN to the evaluation of rock fractures. In other words, by creating heat maps of tunnel face images, CNN is utilised to evaluate rock mass in categories that are associated with discontinuities. The CNN model is most accurate when six convolution layers, four pooling layers, and three dense layers are used. This yields an accuracy of 75.0~88.0 per cent. Thus, the CNN model is verified to be feasible method to evaluate rock fractures.

Nov 29, 2022

By A Crosky, S Saydam, H Chen, H L. Ramandi

Cable bolts and rock bolts are used as primary and secondary anchoring systems in many underground mines. Reports on the premature failure of cable bolts and rock bolts due to stress corrosion cracking (SCC) in underground coalmines have been increasing in the past two decades. The previous studies found that the SCC in both rock bolts and cable bolts occur as a consequence of atomic hydrogen diffusion into the material, which is known as hydrogen-induced stress corrosion cracking, HISCC (Craig et al, 2016; Wu et al, 2018b). While research to understand the process of SCC occurrence in underground mines is still required, finding a prevention solution to protect the bolts from HISCC is crucial. In this study, we analyse a variety of commercially available coatings for steel corrosion prevention, including barrier coating (ie epoxy, polyester TGIC) and sacrificial coating (hot-dip galvanising). We test the coating on coupons manufactured from rock bolts and cable bolts used in the coal mining industry.

Nov 29, 2022

By B Vorster, T Medhurst, A Huey

Roof conditions at Oaky North Mine can be prone to stress related damage and/or time dependent degradation. The ability to identify these areas prior to mining has proved challenging using traditional methods. To help alleviate this situation, a study was initiated to investigate methods for roof characterisation using geophysical logs. This involved the use of neutron log data to provide an indirect measure of the proportion of carbonaceous/micaceous laminae present in the immediate roof strata. Detailed analysis of the shale–porosity inter-relationships arising from this analysis provided a means to estimate the proportion of laminations for a given roof interval. This paper outlines the process and how it was used to improve the current GSR modelling and hazard mapping process.

Nov 29, 2022

By A Sainoki, D Fukuda, K Shioya, C Zhang, M Sharifzadeh, T Yamaguchi, S Saydam, J Kodama, C A. Amagu, Y Fuji

In an open pit mining, ensuring stability of rock slope has been one of the major challenges. As the instability of rock slopes can results in slope failures; consequently, endanger the lives of workers, affect mining operations, and often lead to economic losses. Therefore, it is practical important to study the stability of rock slopes to ensure safe, smooth, and effective mining. The stability of rock slope of about 130 m height at Higashi-shikagoe limestone quarry, which has experienced slope failures four times since 1996, was assessed. The rock mass at the quarry is consists of mainly limestone, schalstein and slate rocks intersected by clay seams of about 70 m thick at footwall of the rock slope. Previously, the effects of limestone excavation at the foot of the rock slope and shear failure due to rainfall infiltration have been investigated. Although clay is widely known to plays a vital role in the stability of slopes in engineering projects including mines, but its impacts on slope deformation at the study quarry are not adequately examined. Therefore, the present study addressed the impact of presence of clay on slope deformation at Higashi-shikagoe limestone quarry by employing both field displacement measurements and numerical simulation. Firstly, surface displacements measured by automated polar system (APS) for over eight years were analysed to understand the overall characteristics of the slope deformation. The measured results show that the displacement gradually decreases with time. The maximum displacement of about 100 mm was observed at middle of the rock slope. Secondly, the effect of deterioration and plastic behaviour of the thick clay layer were simulated using two-dimensional finite element method (2D FEM). The simulated results reveal that the clay exhibited deterioration by water contact and plastic behaviour arising from mining activities at the footwall of the clay zone. Based on the characteristics of the measured and simulated results, it was found that the displacement induced by the effect of deterioration of clay is more noticeable at the north side of the quarry whereas displacement induced by excavation is quite significant at the south side of the quarry if clay behaves as an elasto-plastic material.

Nov 29, 2022

By S J. Chen, N Jiang, Y S. Ding, F X. Li, D W. Yin, F Wang

This study assessed the deformation failure characteristics of rock-coal composites with different height ratios. Uniaxial compression tests were conducted using an acoustic emission monitoring system and XTDIC three-dimensional full-field strain measurement system. The results showed that with the increase in rock-coal height ratios, the uniaxial compressive strength of composite samples increased from 5.26 MPa to 14.61 MPa. The evolution of the deformation localisation zone of the composite samples is closely related to the initiation and propagation of the primary cracks in the coal samples. At the moment when the main fracture of the coal samples occurs, there is a large drop after the peak of the stress-strain curve of the composite samples, and the height of the rock samples increased to varying degrees, which indicated that the failure of the coal samples induced the rebound deformation of the rock samples. With the increase in rock-coal height ratios, the rebound deformation amount of the rock samples decreased from 0.042 mm to 0.008 mm, and the rebound deformation rate decreased from 0.210 per cent to 0.010 per cent. Meanwhile, the rock samples’ rebound deformation releases part of the elastic energy to act on the coal sample, further contributing to the destruction of the coal samples. Compared with single composite coal samples, the coal samples of the composite samples have much more failures. In addition, with the increase in rock-coal height ratio, the input energy density, elastic energy density, post-peak release energy density, and residual elastic energy density of the composite samples increased, the dissipation energy density decreased, and the percentage of pre-peak elastic energy density increased from 98.56 per cent to 99.86 per cent. These results revealed the deformation failure characteristics of rock-coal composite with different height ratios and provided a theoretical reference for understanding the underground dynamic rock failures.

Nov 29, 2022

By I Canbulat, G Si, Y Duan, X Luo

The presence of unfavourable geological structures such as faults and dykes often can contribute to coal burst risk. Seismic events associated with rock fractures tend to cluster around these structures and it is important to understand the characteristics of seismicity for coal burst risk management. In an Australian underground longwall coalmine, two clusters of seismic activities close to the longwall face and within a section of the maingate roadway which was intersected by a major dyke were respectively identified. The induced seismicity in the dyke-roadway area was closely related to the longwall mining. These seismic events were located and the distribution of seismic events shows that more fractures were distributed on the inbye side of the dyke. The spatial-temporal changes of the seismic event locations delineate the fracture propagation as the longwall mined through the dyke. The frequency-magnitude relationship of seismicity was analysed and it was found that it changed significantly when the longwall was mining towards, through and past the dyke. The monitoring results demonstrate that because of the stiff dyke, the seismicity was intensified in the roadway section. It proves that the dyke promoted stress re-distribution and seismicity in its vicinity. More fractures were induced in the hanging wall of the dyke, whereas less strain energy was accumulated and released in the footwall of the dyke.

Nov 29, 2022

By P Mikula, R Geranmayeh, R Carlton, M Ferguson, R Whiting

The concept of using specially designed slot blasts to mine through stress abutments that intersect faults, while controlling fault-slip seismicity, has come of age at Mt Charlotte Mine. Due to the high and adverse stress field and the presence of major faults, the mine is vulnerable to significant fault-slip seismicity. As mining proceeded, advancing stress abutments around various mined areas encroached on several major subvertical faults. If the sequence formed a diminishing pillar between stope and fault, the removal or failure of that pillar daylighted the fault, and often resulted in significant fault-slip seismicity. A new strategy called ‘Tight Slot Blasting’ (TSB) was developed to restrain or dampen this style of fault-slip movement. The TSB has geometric similarities to a conventional cut-off slot used to create stress shadows, but its function is different. Its objective is to trigger and control a sudden shift of the stress state on a fault from an initial stable state, through an unstable transition, to a second stable state. A TSB firing advances a long tall narrow slot through a stressed abutment between a stope void and a nearby fault, using a rapid blast with a low swell ratio, so that the slot substantially and rapidly fills with blasted rock fragments. During the blast process, the stressed rock is rapidly removed and transformed into the fragmented rock fill in the slot. The strategy deliberately allows a fault-slip episode to manifest at a chosen time and place. The tight-packed broken rock in the slot performs an essential shock-absorbing function by controlling the slip amount and rate on the fault, while at the same time the fill becomes compacted by the movement. This controls the dissipation of fault-slip energy, and greatly reduces the seismic response in time and space. A small closure across the slot occurs, with consequent relaxation and destressing of the adjacent rock mass. Stress monitoring data shows that slot creation lowers the abutment stress in the nearby rock mass, while the newly placed fragmented rock fill acts as a shock absorber, providing considerable resistance to substantial fault-slip movement that otherwise could deliver a significant seismic event. First used in 2007, the strategy has been refined to become a routine specialised practice for management of seismically hazardous situations at Mt Charlotte, with 12 successful TSBs conducted to date. Despite mining through multiple high stress abutments, seismic reactions have not exceeded ML 2.1 with any TSB firing, all remaining below the site tolerable maximum of ML 2.3. This paper presents an overview of the strategy, and five case examples of the strategy in critical stressed areas in July 2016, Sept 2017, Dec 2017 and two in Oct 2020. The strategy has successfully managed the seismicity and is expected to remain an essential part of the seismic management plan at Mt Charlotte Mine.

Nov 29, 2022

By J Player, P Mikula, G Sweby

A numerical modelling back-analysis exercise was carried out at a WA gold mine at which early signs of seismicity (rock noise, scatts from active faces) were becoming apparent as depth of mining increased towards the 500 m mark. Some strain bursting had occurred and it was necessary to discover what the implications of this were for greater depth. The aim of the modelling was to: 1. Establish a correlation between observed ground conditions and model predicted damage, in overstressed areas of the mine. 2. Use this correlation to forecast rock mass damage and ground control requirements for proposed future stoping panels at greater depth. Good correlation has been achieved between observed rock mass damage, and a 3D Finite-Element RS3 model, run in elastic mode. Two candidate stress field orientations were modelled. The model parameter best fitting the observations was the Strength Factor (SF), the ratio of strength/stress. The good match (correlation coefficient of 0.7) between observed and modelled suggests that the elastic approach is justified for the depth range and rock mass properties analysed. The correlation also enabled a link between observed damage and installed ground support performance. Using the linear best-fit between observed and modelled, a forecasting exercise was carried out using the same RS3 model, modified to include future stoping. The resulting damage and ground support categories were obtained from the modelled SF for each proposed stoping level. Also, a series of generic geometries was assessed to investigate the impact of varying stope face lead/lag distance, sill pillar height and stope pillar size, on ground conditions. The key finding of the generic geometries were: • Ground support schemes have been defined for the expected conditions. • All ore drives are expected to have significant damage in the backs and rehabilitation. • Lead/lag distance not to exceed 10 m. • Sill pillar/level intervals of less than 20 m require an increase in ground support scheme. • Pillar sizes for maintaining footwall and hanging wall stability should be at least 10 m × 5 m.

Nov 29, 2022

By B Darlington, L Sandberg, O Vallati

The D47 and D39 Mechanical Dynamic Extra bolts (D47 MDX and D39 MDX) have been developed in response to the ever-increasing demand from the mining industry for rock bolts with high dynamic capacity. To prove such capacity, Sandvik has performed numerous in situ dynamic testing with the unique Dynamic Test Rig (DTR) (Darlington, Rataj and Roach, 2019; Roach, Rataj and Darlington, 2019). To complement the collection of testing data, Sandvik, in collaboration with the Swedish Research Institute for Mining, Metallurgy and Materials (Swerim) have performed additional experiments in laboratory condition using Swerim’s new drop test rig. This rig utilises a momentum transfer method to apply a dynamic load to the bolt. The sample falls together with the mass until the support beam impacts stationary dampers and the momentum energy is transferred to the bolt. Part of the charged energy is released by the dumpers while the remaining portion is absorbed by plastic deformation and/or displacement of the ground support element. The D47 and D39 MDX bolts have been tested at Swerim’s test facility with different levels of input energy. Six tests were performed at the specification energy of 36 kJ and six tests were carried out with the maximum allowable energy from the facility, ie 44 kJ. The bolts confirmed their dynamic performance absorbing the input energy without failure. The D47 MDX bolt absorbed up to 33 kJ with 150 mm displacement while the D39 MDX bolt absorbed up to 35 kJ with 162 mm displacement. This work will present an overview of the drop test rig at Swerim’s facility and a collection of results of the test performed on the D47 and D39 MDX bolts. The test method and results will be analysed and compared to the tests carried out with the in situ DTR.

Nov 29, 2022

By A D. Campbell

Sublevel caving (SLC) is a mining method adopted in a wide range of mining depths and ground conditions with various layouts adopted to suit orebody geometry. Sublevel caving offers more flexibility and versatility compared to other cave mining methods and is a low cost alternative to open stoping. SLC also has the advantage that stopes are not required to remain stable during production, and no backfill is required. This flexibility combined with increasing pressure on mines to target deeper and lower grade mineralisation has led to increased uptake of the method. The implementation of SLC mining methods across a wide range of mining depths and rock mass conditions has led to ground control practices which vary globally from mine to mine. To date, there has been limited documentation of ground control practices in SLC mining and few benchmarks available in the literature. This paper describes the main findings from a global benchmark of sublevel cave mines conducted over three years as part of the Caving 2040 research consortium. The purpose of the project was to document and compare operational practices, technical aspects and hazard management techniques across SLC mines around the world. The review included 21 mines spread over four continents and 17 different mining companies. This paper provides an overview of geotechnical conditions, challenges and ground control practices at each of the benchmarked SLC mines. Mine design and sequencing practices adopted for ground control purposes and hazard mitigation are provided with case studies. The impact of depth and rock mass conditions on mining productivity and development rates is also described.

Nov 29, 2022

By T Warren, A Dempster, N Barnett, J Oh, S Saydam

The influence of the insulating properties of lunar regolith was shown in the sub-surface temperature tests performed by the Apollo missions, with no significant temperature fluctuations occurring below 80 cm from the lunar surface even if surface temperatures fluctuated >200 K between lunar days and nights (Heiken et al, 1991). Key to the thermal insulation of the regolith is its low density near the surface having the greatest insulative effect with the lunar regolith becomes denser with depth. As the regolith becomes denser, the thermal conductivity of the regolith increases (Hayne et al, 2017). Thermal modelling software, Oxford 3D Thermal Model, which mapped the lunar surface temperatures effect on the thermal influence at the lunar south pole sub-surface over a lunar year found areas with brief illumination with surface temperatures >120 K could have sub-surface temperatures <112 K that can sustain long-term stable water ice at depths of <30 cm (Paige et al, 1992; King et al, 2020). Further to this, the observation of water molecules or other hydroxyls by the NASA/DLR Stratospheric Observatory for Infrared Astronomy (SOFIA) in non-permanently shadowed regions (PSRs) on the Moon, indicated that water could be present beyond PSRs (Honniball et al, 2021). Using the Oxford 3D Thermal Model in selected regions in the lunar south pole, can provide insights into the location and depth of cold traps that could sustain water ice.

Nov 29, 2022

By P B. Hills

A simple algebraic method of aligning large scale underground excavations such as a crusher station or workshop or indeed any large cavern or mine layout to the optimal stress condition is outlined. The method uses the stress transformation law to determine how the component stresses vary as the stress tensor is rotated around its axis. The aim is to define the orientations at which the maximum and minimum horizontal stresses occur such that the excavation can be aligned with its long axis paralleling the trend of the maximum horizontal stress leading to the minimum potential for overstressing of the side walls. The physical environment in which the stress field is acting is unchanged. At the design location, the trend and plunge of the major principal stress is unchanged. However, the coordinate system by which the location of the stress field is described is arbitrary and the stress transformation law allows that coordinate system to be rotated to a more convenient orientation and for the component stresses to be calculated within the alterative coordinate system. The stress field is typically described in terms of normal and shear stresses aligned to a north–south, east–west, vertical, coordinate system. In this scenario, there are two orientations in the 360° horizontal plane defined by the coordinate system where the horizontal normal stresses are equal, and at 45° to those orientations, two orientations where they diverge to the maximum extent. Those orientations of maximum divergence correspond to the trend of the maximum and minimum horizontal stresses, usually designated σH and σh, and that is what the algebraic manipulation seeks to determine. This technique is a first pass assessment which relies on a knowledge of the full stress tensor. It is not a replacement for numerical modelling or detailed design, but a tool to guide planning.

Nov 29, 2022

By I Canbulat, A Mcquillan

This paper presents a parametric analysis showing the impact of virgin in situ stresses on a shallow (less than 100 to 150 m) high slope in a jointed sedimentary rock environment. Slope stability is assessed at varying ratios of slope orientation and horizontal stresses. The results of this study indicate stress conditions should be included in stability assessments of excavated slopes, particularly where structure is orientated perpendicular to the direction of horizontal stress. Some consideration of stress state is applied in deep open cut pits (eg those with planned excavations of 400–1200 m) (Myrvang et al, 1993; Stacey et al, 2003; de Bruyn et al, 2014; Kozyrev et al, 2015). Dodd and Anderson (1972), Kalkani and Piteau (1976), Lee (1978), Coulthard et al (1992), Noorani et al (2011) have studied the effect or horizontal stress and its impact on slope stability, showing that tensile stresses tend to develop at the crest of the slope, with larger tensile zones for higher horizonal stresses and steeper slope angles (Stacey, 1970, 1973; Sjoberg, 2013). However, the consideration of virgin stresses on shallow slope stability is less frequent (Lynch et al, 2005; Dight, 2006; Lucas, 2006; Sjoberg, 2013). This has led many geotechnical engineers to believe the impact of virgin in situ stresses on open cut slope stability is minimal and not worth time or consideration in modelling, or their effects on slope stability are still poorly understood (Stacey et al, 2003; Sjoberg, 2013).

Nov 29, 2022

By G W. Swana

Elastoplastic parameter is a parameter that describe how much materials behave elastically up to certain stress states and plastically thereafter (Hudson and Harrison, 1997). In the continuum analysis, two main parameters of the elastoplastic parameter are modulus elasticity and Poisson’s ratio. In the slope, elastoplastic parameter holds the main role for stability related to deformation in ductile type of rock. There’s a limitation to determine elastic or plastic deformation at the field for ductile rock type. Field manifestation commonly showed that there was no accumulation zone during and after the sliding failure mechanism, in other hand, at the research area, manifestation of deformation at the toe of slope only indicated by bulging shape. This paper will focus at the sliding failure occurred at Coal mining Pit Y owned by Arutmin Indonesia, which according to failure investigation report similar with the condition described above. This paper also will be based on two hypotheses, first hypothesis is claystone rock mass has not been reached plastic deformation yet and the second hypothesis is there is a chance that elastoplastic parameter of the rock mass has been changed during the deformation/sliding failure process. Research method of this paper are back analysis using probabilistic analysis in Finite Element Method (FEM), which conducted before and after failure. Then, the result of the displacement or deformation of the analysis will be checked with the actual deformation shape. Meanwhile, the change of the elastoplastic parameter will be analysed and interpreted. This paper hopefully able to be developed to study about elastoplastic behaviour of rock mass in actual condition and the influence of another uncertainty factor which determine the slope stability.

Nov 29, 2022

By I Canbulat, J Emery, L Yao and C Zhang

This paper documents a process of data analytics and machine learning applied to coalmine roof convergence data. It follows a publication documenting the formation of the database. For each set of analyses Python scripts were utilised to extract data from an SQL database, with subsequent analyses also executed in Python, utilising open-source tools such as scikit-learn. Preliminary analyses with classic machine learning algorithms included multiple logistic regression, K-nearest neighbours, decision tree, random forest, support vector machine, kernel support vector machine, artificial neural network (ANN), naïve Bayes and multiple linear regression. Results indicated that relationships were complex and non-linear, with the artificial neural network most suitable. An ANN model was then refined through a standard process of hyperparameter optimisation and data augmentation to arrive at a final model. Due to the black box nature of the ANN further insight into how the parameters interacted was sought and found with Shapley additive explanations (SHAP values). SHAP values utilise Game Theory, where each input parameter or feature is a ‘player’ while the data set is the ‘team’. The SHAP value is the impact of each player on the target value, essentially establishing the contribution of each input parameter. The results from all analyses are delivered in the paper, together with insights, applications, strengths, and limitations of the methodology.

Nov 29, 2022

By C Balci, D Tumac, A Sheterpour-Mamaghani, E Dogan, A Kocbay, T Erdogan, A Gumus, H Copur, E Altintas

Excavation of vertical and/or inclined shafts in the underground structures requiring careful design and planning. Raise Boring Machines (RBMs) are commonly used for excavation of shafts for different purposes such as ventilation, orepass, and human-material transportation. Proper selection and accurate performance prediction of RBMs are two main parameters affecting the cost estimation and planning/scheduling. Indentation test is one of the most preferred methods that can be used to predict advance rate of RBMs. This study aims at suggestion of new prediction model for instantaneous penetration rate of RBMs based on indentation tests. Different rock (core) samples (with different geological origins) are obtained from the raise boring application projects in Turkey; then, the indentation tests are carried out on them by using a real-life insert (button), which is used in reamerhead cutters investigated in this study. Finally, the statistical relationships between the field performance and the indentation indices are investigated. The study indicates that the brittleness index (the ratio of maximum applied force to corresponding penetration) can be used to predict instantaneous penetration rate of RBMs used in the vertical raise bored shafts excavating rocks having uniaxial compressive strength lower than 100 MPa.

Nov 29, 2022

By B Liu, W J. Zhang, S Saydam, B Li

Rock bolts are commonly used to reinforce ground in underground mining and civil tunnel environments. Rock bolts serve two main functions: i) they suspend large, loose blocks of ground, and ii) provide a protective pressure arch to restrain the deformation in an excavated void. Automated and precise tracking of rock bolt positions can assist with the operational success of ground support by reducing the amount of labour required in current manual practices. A point cloud is a large list of x, y and z coordinates in three-dimensional space, that when visualised, show a precise 3D representation of a physical environment. Point cloud data can be collected using accurate LiDAR scanners. These scanners can be mounted on a stationary tripod or on a moving vehicle. A key way point cloud data is used is in the bolt detection project being completed in conjunction with UNSW Sydney, which aims to provide an automated location of underground rock bolts from LiDAR scans. The immediate challenge with identifying rock bolts is that they constitute a very small portion of the data set amounting to approximately 0.01 per cent of some of the collected civil tunnel data. The process of detecting rock bolts from point clouds therefore requires a quick elimination of large background data while still preserving the bolt data. A further challenge is that the geometry of underground environments can often be very complex and non-uniform. To overcome these challenges, a two-step coarse to fine deep learning approach is taken. The first step is a coarse background elimination step aimed at removing as much of the background data as possible. The second step is a finer classification method, which uses deep learning to further segment the bolts from the remaining background. Additionally, a computer vision module is being implemented, which is expected to increase the detection rate by adding another dimension to the training data set.

Nov 29, 2022

By M Colwell

The Coal Mine Roof Rating (CMRR) is a rock (roof) mass classification (RMC) system/index that was originally developed by the United States Bureau of Mines (USBM) for aspects of underground coalmine geotechnical design and was first introduced to Australia as a part of the original Analysis of Longwall Tailgate Serviceability (ALTS) project conducted in 1997/1998. In subsequent years further refinement to its calculation was undertaken, such that the CMRR is now an industry standard for quantifying the structural competence of the primary bolted roadway roof interval and has been routinely/widely used by Australian collieries over the last 25 years with great success for roof support/chain pillar design. There have been many publications discussing the use and calculation of RMC systems and this paper also provides an important update and recommendations in how best to calculate the CMRR. However, it is rare to find an explanation as to why and how a RMC system/index satisfactorily takes account of the mechanics and rock mass behavioural issues associated with ground reinforcement. This paper provides such an explanation and insight with respect to the CMRR so it is: 1) better understood, 2) to allay any concerns, and therefore 3) will continue to be confidently used by and for the collieries’ benefit.

Nov 29, 2022

By A B. Jahed, Ö Aydan, T Ito

In this study, the authors compiled some case history data and present some typical examples of rock slope stability issues in Afghanistan with a special emphasis on Kandahar region and categorise rock slope failures according to the principles of modern rock slope engineering. The slopes considered involve rock-cut, natural rock slopes mainly. The effect of structural geology and discontinuous nature of rock mass on both slope-cuts and natural rock slopes is taken into account and some preliminary assessments on the stable and unstable rock slopes are presented. Furthermore, the seismic effect on their stability is also considered. It is also pointed out that similar issues could be observed in open pit mines, which may be exploited in years to come.

Nov 29, 2022

By P B. Hills

Increasingly over the past couple of decades, the importance of understanding the in situ stress regime in underground hard rock mines has become accepted by all. Providers have responded to this requirement and various techniques for undertaking the measurements have been honed while others have slipped from use. It is a simple, though not inexpensive task to engage a provider to undertake the require measurements, and a comprehensive report will ensue. So, what has actually been obtained? What should the geotechnical engineer do next? What tools are necessary to do so? Regardless of the method of measurement, the report will describe the location of the measurement site and describe the basis of the methodology used in undertaking the measurements and a log of the measurement program. Finally, it will include the results, which should incorporate the normal and shear stress components of the full stress tensor. Ground control management plans (GCMP’s) and stress summary reports and spreadsheets prepared by site geotechnical engineers always include the magnitude, trend and plunge of the principal stresses. Remarkably few site-based summaries include the full stress tensor. This is a significant gap as the full stress tensor is vital for any further data manipulation. However, without the algebraic tools to undertake those manipulations, their value is diminished. This paper seeks to provide a checklist of ideas to be considered. It provides commentary on the options available to dissect the stress measurement report and ensure that the maximum possible value is derived from it. The manipulation and presentation of component stress data is also discussed. The various methods of stress measurement are not the focus of the paper but some of the strengths and weaknesses of them over which the site geotechnical engineer has some control, are highlighted.

Nov 29, 2022