Search Documents

By Sanjay Kumar Singh

The mechanics of load transfer in bord-and-pillar mining is not well understood despite the evolution of the art of pillar extraction over the last 20 years via trial and error (empirical) or Rock Mass Rating (RMR), simple monitoring and pillar extraction experiences at neighboring mines. Variations in geologic conditions and pillar extraction methods, along with a lack of comprehensive instrumentation programs for monitoring ground behavior during pillar recovery, are among the factors that make it difficult to predict how strata will respond to pillar extraction. Efficient and safe use of roof supports depends on the interaction between the designed support and coal strata. Of particular interest in this study is the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods and optimum support with load-bearing capabilities in strata control during mass exploitation of underground coal deposits required detailed investigation,?. To provide a better understanding of the mechanics of strata deformation, as researchers, we have collected data and reviewed measurements of convergence and stress in one mine of South Eastern Coalfields Limited (S.E.C.L.), i. e., in North Chirimiri Pondary Hills (NCPH) and have completed numerical modeling with FLAC software for (Fast Lagrangian Analysis of Continua modeling, Itasca India Consulting Pvt. Ltd.) for two typical pillar extraction plans. Stress distribution in the mine roof above pairs of roof supports was calculated to demonstrate how Resin roof bolt support installed support contributed to roof block movement control. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal measure rocks and by pillar extraction sequences and layouts. Also, resin roof bolts and other support systems play a critical role in controlling stability of both the immediate roof and the main roof for a distance of up to 18 meters (i.e., working coal seam height X three times) above the seam. Installed supports provide unique strata control advantages over other types of secondary support by significantly reducing the time between mining and installation of the secondary support. Although resin roof bolts are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at nearpeak capacity(Singh, et al., 2006), whereas posts fail and lose their ability to limit mine roof deformation.

Jan 1, 2012

By Roberto Folchi, Hans Wallin

Lake Mead, the largest man-made reservoir in the United States, is located about 30 miles southeast of Las Vegas, Nevada. For the construction of Lake Mead third water intake, which is entirely placed underground, an underwater excavation was needed at a depth of 100 m (330 ft): a large surface had to be deepened by 20 m (66 ft) in basalt.

Jan 1, 2012

By B. Dyck, C. Rodgers

ABSTRACT Cameco Corporation is revitalizing its Key Lake Operation uranium mill in northern Saskatchewan. The mill currently uses ammonia stripping in solvent extraction (SX) and ammonia yellowcake precipitation. As part of the revitalization, the company considered installing strong acid stripping in solvent extraction (used at its Rabbit Lake Operation), which would lead to using hydrogen peroxide for uranium precipitation. As part of the process evaluation, tests were carried out to study how the drying temperature in indirect fired dryers would affect the uranium peroxide yellowcake precipitate properties. This paper discusses the test work results, including the relationships between drying temperature and product reactivity with water, product colour, product grade, and energy input requirements.

Jan 1, 2012

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component?based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

By Ruilin Yang

"Blast vibrations are essentially a strain/stress wave propagating in rock or structures inthe vicinity of a blast. However, blast vibration has always been quantified in terms ofpeak particle velocity (PPV) or acceleration (PPA), and a meaningful relationshipbetween blast vibration and strain/stress has not been established. The determination ofthe dynamic strain from blast vibration may improve quantification of blast damage andselection of a blast vibration limit for critical structures or high walls. Dynamic strainrelates to rock mechanics or material strength more directly than peak particle velocity(PPV). This paper documents a method to calculate the three-dimensional dynamic straintensor from recorded blast vibration signals. The method is based on determination of thedisplacement gradient at a point of interest for each time instance during the vibrationduration. The method to calculate dynamic strain is applicable to generic seismicwaveforms including near and far field blast vibration from a production blast withmultiple blast holes. In order to minimize measurement errors the specifications of thespacing between monitors and the sampling frequency of the vibration recording aredescribed."

Jan 1, 2012

By Baojie Zhang

The main goal of this study was not only to investigate the effectiveness of the FGX Dry Separator for removing pure rock from run-of-mine coal producing a better feed stock for conventional coal preparation plants but also to optimize the FGX Dry Separator performance for producing a salable clean coal product without using the conventional wet coal preparation processes. A Model FGX-1 Dry Separator with feed throughput capacity of 10 tph was extensively tested at the Illinois Coal Development Park using two coal samples having distinctly different cleaning characteristics. Statistically designed experimental programs were conducted to indentify critical process variables and optimize FGX Dry Separator performance by systematic adjustments of critical process variable parameters. The coal cleaning performance of the FGX Dry Separator was evaluated for the particle size range of 63.5 x 4.76 mm in most cases, although FGX Dry Separator feed consisted of nominal -63.5 mm run-of-mine coals. The best cleaning performance obtained from the FGX Dry Separator is described by specific gravity of separation (SG50) and probable error (Ep) values of 1.98 and 0.17, respectively. The SG50 and Ep values for individual size fractions were as follow: 1.90 and 0.12 for the +50.8 mm size fraction, 1.95 and 0.18 for the 50.8 x 25.4 mm size fraction, 2.01 and 0.19 for the 25.4 x 12.7 mm size fraction, and 2.03 and 0.23 for the 12.7 x 4.76 mm size fraction. These process efficiency measures produced a clean coal with ash content of 13.38% from a feed coal with ash content of 34.45%. Ash content of tailings and middlings streams were 85.09% and 39.57%, respectively. Total sulfur contents of corresponding streams were 3.87%, 4.68%, 6.87%, and 4.62%. For a relatively easy to clean Illinois No 6 seam coal (Cleaning Index: 0.72), only about 0.42% of the clean coal (i.e., 1.6 float fraction) present in the feed was lost to the tailings stream. For a relatively difficult to clean coal (Cleaning Index: 0.53), about 0.98% of the clean coal present in the feed was lost to the tailings stream.

Jan 1, 2012

By Hairong Zeng, Matthew Baumann, Shahram Tafazoli, Edmond Chow

Measurement of rock fragmentation has evolved from a completely subjective and manual process to a statistically objective and semi-automated process. However, ultimately, the vision is to achieve a statistically representative and fully-automated process. From the blast optimization perspective, it is critical to receive reliable rock fragmentation results quickly to incorporate into the planning of subsequent blasts. Since manual rock fragmentation measurement methods tend to be time consuming, a fully-automated method is the practical way to meet these requirements.

Jan 1, 2012

By Samantha Moodley, Rauf Hurman Eric, Cevat Kucukkaragoz, Aditya Kale

"Two titania slags, rutile and synthetic rutile were chlorinated with petroleum coke and CO in a small bubbling fluidized bed reactor. The study aims to identify differences in chlorination mechanism, compare conversion rates, blowover and the chlorination of impurities for the various titania feedstocks at different temperatures.Chlorination rates were highest at 1000ºC; rutile chlorination significantly increases as temperature increases from 800ºC to 1000ºC. At 1000ºC, synthetic rutile had the highest chlorination conversion rate; this was followed by Slag B which in turn was more reactive than Slag A and rutile. The mechanism for slag, synthetic rutile (SR) and rutile chlorination differs. Synthetic rutile feed is porous, providing a larger surface area for the chlorination reaction, hence the highest conversion rates was attained. Titania slag becomes porous with the initial chlorination of FeO and MnO whilst rutile remains solid. As the porosity of slag particles increases so does its tendency to be elutriated. Ti2O3 is oxidized within the early stages of chlorination during the chlorination of FeO and MnO. Ti2O3 not oxidized is then rapidly chlorinated.IntroductionTitanium dioxide (TiO2) is the most common compound of titanium, about 95 - 98% of extracted titanium minerals is processed into TiO2 white pigment [1]. Two processing routes exist for the production of TiO2 pigments, i.e., sulphate and chloride based processes. In the chloride process, titania feedstock is fed to a fluidized bed reactor together with reductant and chlorine gas. A temperature of 1000 - 1300ºC is maintained in the reaction zone and apart from silica, zirconia, uranium and thorium, virtually all the metal oxides in the feed are converted to their respective chlorides [2]. Chlorine is recovered and recycled back to the reactor."

Jan 1, 2012

By M. Javier

Defining the concept of sustainability is an important step for industry and society. It is necessary in order to clarify what it means when debunking the many misinterpretations pervasive in different levels of anthropogenic activities. Essentially, the extractive industry has a harvest of differences. Mining involves the extraction of natural resources which are finite, exhaustible, non-renewable, unsustainable, and pay only once. It is remarkable that the definition of sustainability that we will shortly arrive at has totally different characteristics from the definition accepted throughout society. We categorize nature as having its own destiny which is controlled by its own rules and principles and its own society, and is part of nature; therefore, society depends on nature and not vice versa as the initial focus. To society there are no conditions to humanize nature but only respect nature?s rules. It was a challenge to find simplicity for this task not only for the definition but also for the explanation of this concept specifically, to answer the question, ?what is the true meaning of sustainability?? Finally, we are also able through this definition to provide fuel for wide discussions and stimulate critical thinking to improve such a concept. As a result, we present this definition as the tool for society today and for future generations.

Jan 1, 2012

By Bo Jiang, Lianyun Liu, Hongmin Zhu, Kai Huang

"Watermelon peel is selected as a novel adsorbent to remove Pb(II) from aqueous solution. A simple saponification process is proposed to modify the peel and the adsorbent is characterized by SEM and FTIR. The effects of pH, contact time, initial concentration of Pb(ll), biosorbent dosage and temperature on adsorption of Pb(II) are investigated. Different models are used to fit experimental data. These models indicate that the adsorption process follows the Langmuir model and pseudo-second-order model. The maximum adsorption capacity obtained from Langmuir model is 1.05mol kg-1 for the prepared sorbent. Equilibrium time is attained in 5-10 min for the studied concentrations. The watermelon peel can be used as an effective and low-cost biosorbent for removal of Pb(ll) from aqueous solution.IntroductionRecently, removal of heavy metal ions from industrial effluents by biosorption has become a very attractive topic, since the more serious pollution issues caused by heavy metals emerge frequently, and more strict requirements for its control are called upon by society [1,2]. In this case, most conventional purification technologies are not suitable due to poor cost-effectiveness [3]. For example, chemical precipitation by alkaline reagents usually can not decrease the metal ion concentration below the permissive levels, and also it will produce a large amount of sludge containing toxic metals. Membrane separation techniques can realize deep purification of wastewater easily, although its operating cost is usually high. Thus, considering the high effectiveness, low cost and free-sludge operation, bisorption has become a promising technique in water treatment [4]. The most important thing for this technology is the synthesis of a suitable biosorbent, whose adsorption properties will determine the removal efficiency and economic cost for the whole process. Watermelon is one of the most popular fruits for mankind for its delicious flavor. Usually, the watermelon is consumed mainly for its edible pulp, and its peel is discarded or only used as feed for livestock. Considering the pectin contained in the watermelon peel, just like that in orange wastes in the reported literatures [3], the idea of using it as the raw material to prepare the biosorbents for heavy metal ions removal from the aqueous solution was evaluated in this study."

Jan 1, 2012

By Qingyu Deng, Shiwei Ma, Wang Hua, Guibao Qiu

"The flow properties of the blast furnace slag bearing high TiO2 at high temperature like the viscocity may change a lot due to the formation of the carbonitride inside, causing serious problems on the separation between the metal and the slag. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process with iron ore bearing titania. In this study, the formation of Ti(C,N) in blast furnace and the influences of various factors on the Ti(C,N) formation are investigated by FactSage. It is found that the mass of Ti(C,N) would reach the maximum at 1480 oC, and the product is mainly TiN below 1620 oC, while it is mainly TiC above 1620oC. The order of the factors by the importance from strong to weak was: temperature, the content of TiO2 in slag, basicity of slag, the content of MgO and Al2O3.IntroductionThe titanium dioxide (TiO2) in iron ore bearing titania will be partly reduced by carbon to titanium carbonitride (Ti(C,N)) in blast furnace, causing serious problems on the separation between the metal and the slag because of the change of flow property. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process, especially for the smelting of iron ore bearing titania. Extensive experimental data in regard to the formation of Ti(C,N) has been reported in numerous papers[1-6]. However, only some discrete data can be obtained by experiment, and it is difficult to detect the mass of Ti(C,N) in slag. In addition, the experiment is difficult to be proceeded when the temperature is above 1600oC. Therefore, it is very difficult to make clear the critical condition of the formation of Ti(C,N) by experiment."

Jan 1, 2012

By Donald P. Ziegler, James F. Klausner, Srinivas S. Garimella

"By 2015, nearly half the world's population will live in ""water stressed"" areas. Production of fresh water utilizing waste heat from industrial processes has been identified globally as a research priority.About 15% of the electricity required to produce aluminum is lost as waste heat in the off-gas. However, the low temperature (low grade) of the heat limits reuse. The off-gases contain 50-150 ppm SO2 ; tightening regulations coupled with increasing coke sulfur levels are motivating SO2 control, for which seawater scrubbing is attractive for smelters with suitable access.We describe a process that produces fresh water, utilizing the waste heat while scrubbing SO2 . It uses direct contact between seawater and off-gas to humidify the off-gas. The vapor is subsequently condensed. In smelter trials, a unit treating a slip stream produced high quality water in the anticipated quantity, attaining over 95% SO2 scrubbing. Future work involves scaling the process to be economically attractive.BackgroundPopulation growth, coupled with industrialization and urbanization, are increasing demand for water. Water scarcity already affects every continent. Around 1.2 billion people, or almost one-fifth of the world's population, live in areas of water scarcity, and 500 million people are approaching this situation. By 2025, 1.8 billion people will be living in countries or regions with absolute water scarcity, and two-thirds of the world's population could be living under water stressed conditions (< 1,700 m3 per person annually) [1]. An assessment by the U.S. General Accounting Office revealed that under normal conditions, by 2013, water managers in 36 states in the USA anticipate water shortages, and that the number might grow to 46 states under drought conditions [2].The obvious choice to alleviate water scarcity is the 97% of available water in the oceans, which is saline and requires desalination for use in biological, agricultural and industrial applications. Technologies developed for desalination include Thermal Distillation, Reverse Osmosis (RO), Electro-Dialysis, and Vacuum Freezing. Distillation and RO are the most commercially prominent. Thermal distillation technologies include Multiple Effect Distillation (MED) and Multi-Stage Flashing (MSF). The report commissioned by the World Bank [3] is one of the many excellent references on desalination technologies. According to the International Desalination Association working paper [4], there were more than 17,348 industrial scale desalination plants installed or contracted by 2004. The total production from these plants is on the order of 8.3 billion imperial gallons per day. RO provides 47.2% of the total capacity. The leading thermal process, MSF, provides 36.5% of the total capacity. Although MSF and RO technologies currently provide the most cost effective means for desalination, their drawback is that they are very energy intensive, and whether or not they remain cost effective strongly depends on energy prices and energy supply."

Jan 1, 2012

"The pressure leaching of alkali-pretreated limonitic laterite ore in nitric acid was studied. The optimal leaching conditions are as follows: leaching temperature of 458 K, initial nitric acid of 2.44 mol/L, leaching time of 60 min, liquid to solid ratio of 2:1 mL/g, agitation speed of 500 RPM. Under the above conditions, the extraction of nickel and cobalt can be achieved as approximate 95% and 80% respectively while that of iron is as lower as 1%. The leaching residue containing 70% of iron in the form of hematite and trace amount of chromium is suitable as the raw material for iron-making. The nitric acid in the leaching solution can be regenerated and further recycled to leach. INTRODUCTIONIt has been estimated that 60%-70% of the world land-based nickel resources presented in nickel laterites containing 130 million tons of nickel although these only accounted for about 42% of the world nickel production (Sudol, 2005; Luo et al., 2010). The nickel resource of laterite has not yet been fully utilized. Due to the increasing global demand of nickel and the declining global reserves of nickel sulphides, there is an increasing focus on the processing of the huge reserves of laterite ores today. Nickel laterite ores can be simply divided into two types, namely, silicate-rich and limonite. The former can be treated effectively by pyrometallurgical process in which the ferronickel product or nickel/iron sulphide matte is produced (Monhemius, 1987). The limonitic laterite is rich in iron in the form of goethite which is the main nickel-bearing mineral and usually contains cobalt associated with a manganese phase (Chang et al., 2010; Georgiou and Papangelakis, 2004). The limonitic laterite is usually processed by hydrometallurgical methods, such as atmosphere acid leaching (AL) (Xu et al., 2005; McDonald and Whittington, 2008), high pressure acid leaching (HPAL) (Chou et al., 1977; Georgiou and Papangelakis, 1998; Rubisov et al., 2000; Whittington and Muir, 2000) and reductive roasting-ammonia leaching (Caron Process) (Whittington and Muir, 2000; Valix and Cheung, 2002). The AL process can proceed at lower temperature, thus the operation costs may be very low. But two biggest problems associate with the AL process, namely, the slow rates of nickel extraction and potentially the significant amount of impurities such as iron and aluminum in the leaching solutions, which hampers the wide application of the AL process. The Caron Process uses the pyrometallurgical and hydrometallurgical methods together to obtain the metallic values, but the overall metal recovery is relatively low, especially for cobalt. In recent years, the environment-friendly process of HPAL has become increasingly important because it is most suitable for low-grade ores and leads to high extraction of the valuables. However, the HPAL process needs a much higher temperature and pressure (503-533 K, 4-5 MPa) to maintain a relatively fast leaching rates, which results in higher operation costs. Moreover, another serious problem of scale formation in autoclaves occurs in the HPAL process, for example, in Moa Bay, up to 20 cm scale may build up resulting in 5 days descale downtime per month. In addition, the iron residues cannot be utilized for ironmaking due to the presence of high content chromium (Ema and Harada, 1987; Owada and Harada, 1987; Takagi and Furui, 1987)."

Jan 1, 2012

By C. Stacy

The mining industry is changing rapidly. Competition among OEM and aftermarket vendors increases dramatically each year as a result of mergers and acquisitions, and especially technology advancements in the mining industry. Adding value to mine operations by delivering technical value and differentiation is becoming more subtle and more difficult to accomplish. Because of this, identifying and protecting intellectual property has become more important to the product development, engineering and marketing/sales continuum than it had been in the past. How companies protect intellectual property and determine the value of those assets is critical to the sustainability and differentiation of technology providers in the mining industry.

Jan 1, 2012

By M. Fan

Froth flotation is the most widely-used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different particle size fractions of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50 mm inside diameter column and a 152 mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during coal froth flotation process improved flotation efficiency. The use of nanobubble in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.

Jan 1, 2012

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminick, D. Evans-Lamswood

"Abstract — Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite."

Jan 1, 2012

By C. Heiss, A. Hofmann

Due to an explosion in an Austrian steel works during the basic oxygen process, the Chair of Mining Engineering and Mineral Economics at the Montanuniversitaet Leoben was assigned with the set-up of a test arrangement to study the effects of large-scale particle emissions on the plant´s installations and the testing of various structures and structure-combinations to be applied as explosive-proof enclosure.

Jan 1, 2012

By Yuanbo Zhang, Yongbin Yang, Guanghui Li, Zhengwei Yu, Yufeng Guo, Tao Jiang, Xiaohui Fan, Youming Hu

"Composite agglomeration process (CAP), as an innovative method for preparing blast furnace burden, was developed and has been put into operation in China. CAP is different from traditional agglomeration processes of iron-bearing materials involving sintering and pelletizing. Compared to the traditional agglomeration processes, CAP is characterized by several strengths such as permission of diverse iron-bearing materials in production, obvious improvement of permeability in the feed bed, decreasing the fuel consumption and remarkably increasing the productivity of sintering machine. Furthermore, the use of the composite agglomerates prepared with CAP is capable of obviating the negative effects caused by the differences in quality of sinter and pellets on the operation of blast furnaces. This paper mainly presents an overview of the principle and applications of CAP.Development Background and Principle of CAPhe traditional agglomeration processes including sintering and pelletizing have been the two predominant methods for preparing ironmaking burden from iron-bearing materials. Sintering is a way for agglomeration by heating the coarser fine ores (general granularity 0~10mm). The mechanical strength of irregular porous sinter is obtained by the solidification of molten phase at high temperature process. It has been shown that the production of high basicity sinter (R=1.8~2.2) is characterized by low energy consumption and high efficiency compared to low basicity sintering. Meantime, the finished high basicity sinter is characterized by good mechanical strength and metallurgical performance. Pelletizing is another way for agglomeration by firing wet green pellets, which are balled from the fine grained iron ores or concentrates. Based on the differences of chemical compositions, the finished pellets can be divided into acidic oxidized pellets, fluxed pellets, magnesium-bearing pellets, and so on. The acidic oxidized pellets are the dominant products of modern pelletizing."

Jan 1, 2012

By Xuewei Lv, Yuelin Qin, Guibao Qiu, Chenguang Bai

"Blast furnace slag (BF slag), is the main by-product in the ironmaking process, which contains large amounts of sensible heat. To recover the sensible heat, this paper described the hot experiments which were carried out in a rotary multi-nozzles cup atomizer, where the molten BFS was transformed into granules without water impingement; subsequently, a new method-pyrolysis the printed circuited board (PCB) with the hot BFS particle, was proposed for recovering the sensible heat in this study. The gaseous products were analyzed by gas analyzer. The residual of the PCB was analyzed by FT-IR and XRD respectively, and the obtained slag particles were analyzed by XRD.The results showed that it is a feasible process of pyrolyzing PCB powder with the hot BFS particle. The sensible heat of hot BF slag could be converted to chemical heat and a large amount of combustible gas could also be generated during the process.IntroductionDue to the rising of the product cost of blast furnace iron (BFI) and the increasing public awareness of environmental problems, the steel industries have to focus on the energy saving and emission reduction. Blast furnace slag (BF slag) is a byproduct from blast furnace exhaust temperature of 1450°C or so, is a high-quality waste heat resources. In China, the steel industry produces approximately 220Mt ofBFS per year, and the enthalpy of those slags is approximately equivalent to 13.3% of the whole energy consumption in the ironmaking process[!]. It can be seen, recycling waste heat is an important way of energy saving for iron and steel enterprises. The molten slag was treated by conventional water quenching method without any recovery of heat in spite of its huge potential. Also, the water quenching process consumes a plenty of water, pollutes the air and water[2]. Additionally, the extra energy is necessary for the drying process of slag to produce cement. As a kind of secondhand resource which can be reused, the BF slag contains a large amount of sensible heat. To recover the sensible heat of BF slag, three key problems should be considered, which refer to ( 1) the dry granulation of BFS without consuming water, (2) how to recover the heat of slag particles efficiently, (3) how to use the slag particles after heat recovery."

Jan 1, 2012

By R. Erpelding

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012