Search Documents

By Huimin Lu, Shi Zhou, Lisha Yang

"The Zeolitic imidazolate frameworks (ZIFs) were successfully synthesized by applying a combination of ionothermal synthesis and microwave energies for rapid synthesis. The synthesis was proceeded under various conditions including different raw materials, reaction temperature as well as microwave irradiation time. Zeolitic imidazolate frameworks (ZIFs), also known as coordination polymers, are new type of porous materials formed by inerratic polyhedral in three-dimensional. They are the ideal crystalline substances for gas separation and storage. The assynthesized samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), thermal gravimetric analysis (TGA) and C02 adsorption test. Results illustrated that the synthesized samples had stable structure, high thermal stability (up to 530 °C) and C02 adsorption capacity (10.2 cm3/g at 0°C under ambient pressure). This novel method also showed great advantage with high energy efficiency, safe synthesis conditions, and rapid crystallization time (60 minutes).IntroductionNowadays, carbon dioxide capture has become imperative due to the global warming caused by the increase of C02 in the atmosphere, especially produced by the concentrated sources such as power plants [1]. Zeolitic imidazolate frameworks (ZIFs), also known as coordination polymers, are ideal crystalline substances for gas separation and storage due to their structure diversity, high thermal and chemical stability [2-5]. They are formed by inerratic polyhedra in threedimensional with large cages and small apertures. Traditionally, ZIFs are synthesized by solvothermal method in a sealed autoclave under autogenous pressure [6-9]. However, in order to generate the products, the solvothermal temperature should not be lower than 100°C according to the sovlothermal mechanism. Moreover, at such a temperature, molecules with a low boiling point (such as water) may generate high pressure in reactor which might cause danger [9]. Thus the synthesis requires the equipment to possess resistance to autogenous pressure and corrosion. Further, conventional solvothermal methods need a long time to prepare products, usually a few days, which is a large energy consumption and inefficiency. So it is interesting to synthesis ZIFs through other ways under mild reaction condition with high energy efficiency."

Jan 1, 2012

By R. Oler

The need for yieldable ground support, particularly in high stress or deep mining conditions, has grown in recent years. This paper highlights some of the current industry limitations and provides selection criteria for a new yielding ground support system, DSI?s Dynatork Bolt. This bolt distinguishes itself by withstanding 16 ? 30 kJ of energy deflecting loads anywhere from 7 ? 20 tons (depending on the energy). A summary of the laboratory test results and case studies will also be presented as a measure of the performance of this dynamic product.

Jan 1, 2012

The Discrete Element Method (DEM) is a powerful tool for analysing the flow of charge, the energy consumption and the pattern of energy utilisation of a SAG mill. With the development of laser scanning measurement, the detailed internal working surfaces of a SAG mill can now be included in DEM models. Using scanned results for new and worn shell liners for a 32? (9.75 m) SAG mill, it is shown that the feed and discharge lifters have significant effect on the flow of the charge introducing significant threedimensionality. The effects of the resolution accuracy of liner geometry and the lower cut-off of the rock size distribution are explored. Finally, using a matched new and end of life worn liner and operating conditions taken from site surveys, the effect of wear on charge motion, distribution and energy utilisation are evaluated.

Jan 1, 2012

By J. A. L. Napier

It has been established that significant time-dependent stope convergence may occur over time periods of hours and days in certain hard-rock gold and platinum mines. The source of this time-dependent behaviour appears to be associated with both pre-existing discontinuities and with mining-induced fractures that form near the stope face. These induced fractures may be associated with blasting processes and may also be formed in response to high stress concentrations in the unmined regions immediately ahead of the stope face. In shallower platinum mining operations, time-dependent behaviour is, however, observed to be much less marked unless some form of specific mining-induced fracturing occurs. One particular case of considerable interest is the time-dependent behaviour that is found to be associated with the formation and deployment of crush pillars. The purpose of the paper is to present a simple limit-equilibrium computational model of this behaviour that is sensitive to both the formation sequence and the size of planned crush pillars in a mine layout. This model provides a useful means to optimize the sizing of crush pillars, and at the same time may be used to identify potentially hazardous circumstances in which pillars may not crush in a stable manner.

Jan 1, 2012

By A. G. Taylor

High value materials, such as gold, platinum and other precious metals are subject to loss through unauthorized removal from mines, smelters, refiners, and other places where such materials are processed. A study published in 20011 determined that between 1994 and 1998 an average of 603 kilograms of gold per year was stolen from South African miners and subsequently recovered. This does not include the gold that was stolen but not recovered. At 2011 prices, 603 kilograms of gold would be worth approximately $33 million. Mine security personnel believe that the unrecovered stolen gold far exceeds what is recovered2. Traditionally, metal detectors have been used to screen personnel leaving secure areas to discourage such unauthorized removal. However, with the current near-record prices of gold, platinum, and other precious metals, it has become worthwhile for people exiting a facility to walk out with quantities of product that are too small for ordinary metal detectors to register, resulting in substantial financial losses.

Jan 1, 2012

By Jorge Beim

Helical Piles are increasingly being used to support and rehabilitate structures subjected to compressive axial loads. Traditionally, empirical correlations between installation torque and load capacity of helical screw piles are used as the field quality control. Load tests, however, are always recommended to validate the installation process and design methodology. This paper describes a test program performed on helical piles installed at the National Geotechnical Experimentation Site of the University of Massachusetts - Amherst campus (UMass-Amherst), well known for its deep varved clay deposit. Seven of these piles were submitted to Dynamic Load Tests using the Pile Driving Analyzer® (PDA), and also to Static Load Tests. Good agreements were obtained between the results of the dynamic and static load tests, encouraging the use of the former testing method as a viable alternative to the latter for determining the compressive load capacity of helical piles installed in cohesive soils. The results of the load tests were also compared to the predictions based on torque correlations, resulting in correlation coefficients which were higher than the ones traditionally used.

Jan 1, 2012

By Mansoor Barati, Shaghayegh Esfahani

"The slag from extraction of ferrous and non-ferrous metals is a potential heat source which if treated properly can contribute to recovery of a significant amount of energy. The waste heat of slag may be used to generate steam, synthetic fuel gas, or electricity. Although several technologies have been investigated for this purpose, very little has been achieved in terms implementing the technology in industry. In this article, the development and application of various granulation techniques are reviewed and the methods to recover energy from granulated slag are discussed.IntroductionEvery year, more than 422 million tons of slag is being produced around the world as a by-product of the metal manufacturing at temperatures of up to 1300-1600°C [1, 2]. Currently slags are either disposed of or treated by processes such as granulation. Through the granulation process, most slags can be converted into a material which may be fully used as a cement feedstock. Conventional cement production is an energy intensive process with large emissions of CO2; therefore, the replacement can both be energy saving and environmentally friendly. However, for this purpose, the slag should have what is known as a “glassy” content (i.e. it should be amorphous) which requires rapid cooling rates that are not easily achieved due to the very low thermal conductivity. The main challenge in all these processes is to granulate the slag at a high cooling rate while the heat is also being recovered."

Jan 1, 2012

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By Roger M. Turpening

This study was performed to examine the feasibility of using seismic shear waves to detect the presence of abandoned coal mines. !he Antiquity Coal Mine near Antiquity, Ohio was used as a region of known voids. No attempt was made here to accurately locate the mine tunnels if detection was obtained. The results of this study were positive. Sharp changes in the amplitude of the received shear waves were clear indications of the presence of a fluid (gas or liquid) filled region between the source and receivers. When moving the source showed no change in the received signals it was concluded that the voids existed beneath the sensors. Prior to these tests drilling (SM-3) had determined that a void did exist in this area. This void was confirmed by this shear wave test and two additional voids were found.

Jan 1, 2012

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012

By Nils Eivind Kamfjord, Roar Jensen, Ingeborg Solheim

"SINTEF has carried out several pilot scale silicon process experiments in the past, but always with an open off gas system. In order to test the possibilities in running a semi closed furnace operation, a new off gas hood has been designed and tested. The off gas hood is designed to collect all off gases to gain insight into the phase compositions in the off gas and at the same time have the opportunity to monitor and maintain the charging/stoking of the furnace. The furnace hood has regulation and control of the air inlet into the combustion zone in two different heights. The off gas temperature and composition was continuously monitored and analyzed during the experiment. In order to expand the knowledge on NOx- formation in silicon metal production, such information is vital.IntroductionBecause of the negative environmental impact, the attention towards all kinds of NOX emissions increases in Norway. The authorities’ demand towards better surveillance and control of emissions increases as well.Earlier and new industrial measurements in FeSi- and Si-metal furnaces reveal quite high NOX-emission. The measurements also show that the NOX formation (mainly as thermal NOX) is distinct connected to the formation of dust (SiO?SiO2) in the combustion chamber above the furnace surface, when the temperature is high and the access to N2/O2 is good. This means that stoking, charging and temperature straight above the furnace surface is important factors for the NOX formation."

Jan 1, 2012

Lonmin RoM ball mills are treating two types of feed ore produced by conventional mining and mechanised mining methods. It was reported that reduction in mill throughput was observed when treating the mechanised mining ore. Detailed grinding surveys were conducted for troubleshooting. Ore samples were collected for breakage characterisation using a JKRBT based on different particle density components. XRD analysis was conducted to investigate the association of minerals with density components. The plant surveys and the breakage characterisation tests all suggested that the two mining methods did not significantly affect either the ore breakage properties or the RoM mill performance. Instead, the mill discharge open area exerted a remarkable influence on mill throughput. The RoM ball mill operated at Lonmin K4 Concentrator has been proven to be a versatile mill that performed stably with variations in feed size distribution and feed ore changes by different mining techniques. The reasons are elucidated by the multi-component breakage characterisation and the plant surveys data.

Jan 1, 2012

By Uldis Jansons

This report evaluates the economic Mining feasibility of four selected mineral deposit types that can be anticipated to be found in (d)(2) lands in the western Brooks Range, Alaska. The major assumption made for this study is the availability of a rail system for transporting equipment and concentrates for the base metal mines. Commodity prices used are those in existence in July 1976. Mine models were established based on known deposits and then evaluated. A lead-zinc-silver-barite deposit for which grades were available but ore reserves were assumed would require approximately 25% higher ore grades or higher metal prices to yield a 15% discounted cash-flow rate of return an the investment if mined at a rate of 10,000 tons per day open pit methods. Large copper-zinc mineral deposits could be mined economically at rates either of 5,000 tons per day underground or 10,000 tons per day by open pit methods. A high-grade copper deposit require a copper price of over one dollar ryes pound to yield an economic profit to be mined at 2,000 tons per day by underground methods. A small high-grade gold underground mine would require a gold price of about $295 per ounce to yield a 20% discounted cash-flow rate of return on investment if all new mine equipment were used and if existing labor rates were paid: Enterprising mining groups operating as partnerships might be able to operate this mine profitably at a gold price of about $152 per ounce, perhaps slightly less.

Jan 1, 2012

By Mohammed Sakr

This paper presents the results of a full-scale axial compression and tension (uplift) testing program executed on large-capacity helical piles installed in very stiff to very hard clay till soils (i.e. cohesive soils). A total of ten tests including six axial compression tests and four tension (uplift) tests were carried out. The results of the axial compressive and tensile pile load tests and field monitoring of helical piles with either a single helix or double helix are presented in this paper. Helical piles are traditionally used to support light to medium loads (i.e. loads up to 500 kN or 56 tons). However the results of the present study confirmed that helical piles can support significantly higher axial compressive loads up to 2450 kN or 275 tons, which is about 5 times traditional design loads. The study also demonstrated the high tensile capacities of helical piles which was as high as 85% of their compressive capacity. Hence helical piles can provide a viable design option for foundations supporting relatively heavy loads.

Jan 1, 2012

By I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke, and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale Fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL) in Fairchance, PA, using Ponderosa Pine, Red Oak, Douglas-fir, high and low volatile coals, PVC and SBR conveyor belt, No. 2 diesel fuel, and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector, and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations, and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (1). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters? Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2012

By Dong Liang, Honggang Zhong, Zhenxing Yin, Qijie Zhai

"2507 super duplex stainless steel (SDSS) has been widely applied in a marine environment, attributing to its excellent pitting corrosion resistance and mechanical properties which are particularly determined by the nitrogen precipitation behaviors and volume fraction of ferrite. In this paper, various cooling rates were obtained by applying four different moulds with the common gating system. By which the influence of cooling rates on nitrogen precipitation behaviors and the ferrite fraction in cast 2507 SDSS was comparatively investigated. The results showed that nitrogen porosity could easily precipitate in cast 2507 SDSS under standard atmospheric pressure. The number of nitrogen holes increased with decreasing the cooling rates, and the holes mainly distributed in three zones, i.e. the interface between the horizontal and vertical columnar grains, top vertical columnar grains and the final solidification region. Additionally, higher ferrite fraction was obtained with lower cooling rates.IntroductionDuplex stainless steels (DSS) have a dual-phase microstructure consisting of ferrite (d) and aus-tenite (?). Due to the combined advantageous properties of d and ? phase, their application rapid-ly increased in industry [1, 2]. Super duplex Stainless Steel (SDSS) is the third generation of du-plex stainless steels, of which the alloy elements Cr, Ni and N content are higher than the stand-ard 2205 DSS. Because it has high contents of alloy elements, the SDSS has better mechanical properties, and its pitting resistance equivalent number (PREN) reached a point 43. Hence SDSS has been used in petroleum chemical industry, the marine equipment and harsh corrosion environments [3]. SDSS contains ferrite stabilizing elements, such as Cr, Mo and Si, and austenite stabilizing elements like Ni, Mn and N [4]. Many researchers have studied the effects of these elements on the stabilization of d and ? phase and the ratio of the two phases. High nitrogen con-tent is another prominent feature of SDSS. Nitrogen addition to SDSS is very effective for improving its mechanical properties [5] and corrosion resistance [6], such as pitting resistance in NOx environment. To increase the nitrogen content in steels, a lot of work had been done. N. Nakamura and S. Takaki [7] examined the behavior of nitrogen absorption in Fe-23Cr alloy powder by sintering in nitrogen gas atmosphere, they found nitrogen content easily up to 1.0 wt. %. Using devised NH3 gas injection system, W. Park et al. [8] successfully produced austenitic Fe–23.5Cr alloys containing over 3 wt. % of nitrogen. Further-more, W.P. Tong et al. [9] stated that nitrogen percent was extraordinary high (about 10 wt. %) in pure iron plate. However, the above methods are difficult to be applied to large-scale industrial production."

Jan 1, 2012

By J. P. Beukes

South Africa holds approximately three-quarters of the world?s viable chromite ore resources and dominates the global production of ferrochrome. Albeit completely unintended, small amounts of Cr(VI) are formed during ferrochrome production. Certain Cr(VI)species are regarded as carcinogenic, hence making the treatment of some ferrochrome waste materials necessary. In this paper, the Cr(VI) treatment strategies currently employed by the South African ferrochrome producers are investigated by means of a literature review and a questionnaire survey. From the discussion, it is evident that various treatment strategies are available to deal with Cr(VI)-containing waste in the ferrochrome industry. However, by far the most commonly applied treatment strategy remains the aqueous reduction of Cr(VI) with ferrous iron. The advantages and the correct application of this strategy, together with the disadvantages and pitfalls, are argued. Innovative improvements on historic practices are also discussed

Jan 1, 2012

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"A simplified finite-difference time-domain (FDTD) algorithm for modeling microwave propagation in magnetic dielectric materials was developed and employed to study the microwave dissipation in magnetite. Heat transfer during microwave heating of magnetite was subsequently investigated by solving heat transfer differential equation using explicit finite-difference (EFD) method. It is observed that temperature of magnetite surface increases rapidly in the first minute due to the rapid strength decays in both electric and magnetic fields within a short distance along the path of microwave dissipation. A temperature peak, initially formed at the surface of the sample slab, migrates inward as heating time extends and microwave power increases.IntroductionAs one of primary materials in iron and steel industry, magnetite exhibits excellent microwave absorption capability, which leads to great energy conservation in microwave assisted steelmaking [1,2]. The fast temperature increase in microwave heating of magnetite can be attributed to both dielectric and magnetic losses [2]. Although much experimental work has confirmed this observation, detailed computational studies for modeling of microwave field dissipation in magnetite at commonly used frequencies, such as 915 MHz, has not been well addressed [1,3].Finite-difference time-domain (FDTD) method is widely used in computational electrodynamics modeling to simulate the dynamics of electromagnetic wave scattering from various media [4,5]. This approach requires modeling algorithm to be formulated with integration of specific characteristics of each medium. An extensive literature survey indicates that current formulations are only suitable for modeling electromagnetic waves propagating in normal dielectric lossy materials [5,6]. Since magnetite is a magnetic dielectric material in which both dielectric and magnetic properties contribute to the heating process under microwave irradiation, a specific algorithm should be developed for the simulation."

Jan 1, 2012

By Youzhen Zhang

The drilling boom is the key component of a roof bolter, and it has significant impact on the performance, safety, and reliability of the overall working device. In this paper, the experimental modal parameters of a drilling boom at low frequencies are identified with the Laplace wavelet correlation filtering method. Based on the obtained experimental parameters, a finite element model of the drilling boom is revised using an optimization algorithm to improve its accuracy. The dynamics of the drilling boom are analyzed through its modal and harmonic response. As a result, an improvement for the drilling boom is proposed to fix the weak links and enhance the dynamic performance.

Jan 1, 2012

By C. Lottering

Copper sulphate solutions are produced during the pressure leaching of first-stage leach residue in a typical base metal refinery process. Apart from impurities such as selenium and tellurium, this leach solution also contains other precious metals (Rh, Ru, and it) due to dissolution in the pressure leaching stage. Selenium and tellurium are removed from the leach solution by precipitation with sulphurous acid, since these elements negatively affect electrowinning. This study investigates the feasibility of modifying the Se/Te precipitation process step to achieve significant rhodium precipitation in addition to selenium and tellurium precipitation, in order to reduce the rhodium inventory of the process. Thiourea, S02, formaldehyde, formic acid, and sodium thiosulphate were evaluated to determine which of these reagents would achieve the highest Rh precipitation. Based on these screening tests, SO2 and thiourea were selected to be used as precipitation reagents in optimization tests. During these optimization tests, the operating temperature (80 to 150°C) and the amount of reagent added (80 to 140 per cent excess) were varied to evaluate the effects that these operating conditions have on the precipitation behaviour of Rh as well as Se, Te, Cu, and Ni, and to propose appropriate operating conditions. It was found that thiourea resulted in good Rh and Se precipitation (typically in excess of 90 per cent), but precipitated noticeably more copper and nickel from the solution than when SO2 was used. In addition, thiourea had poor Te removal characteristics. SO2 achieved a maximum of 70 per cent precipitation of the rhodium. Faster kinetics and a larger extent of Te precipitation were, however, observed when using SO2 compared to thiourea.

Jan 1, 2012